Materials Science and Engineering Commons^™

Sub-Bandgap Photon-Assisted Electron Trapping And Detrapping In Algan/Gan Heterostructure Field-Effect Transistors, Andrew Gunn

All Theses

We have investigated photon-assisted trapping and detrapping of electrons injected from the gate under negative bias in a heterostructure field-effect transistor (HFET). The electron injection rate from the gate was found to be dramatically affected by sub-bandgap laser illumination. The trapped electrons reduced the two-dimensional electron gas (2DEG) density at the AlGaN/GaN heterointerface but could also be emitted from their trap states by sub-bandgap photons, leading to a recovery of 2DEG density. The trapping and detrapping dynamics were found to be strongly dependent on the wavelength and focal position of the laser, as well as the gate bias stress time …

Controlled Manipulation Of Droplets On Fibers: Fundamentals And Printing Applications, Yueming Sun

All Dissertations

In this dissertation, the drop interactions with a single fiber is discussed under an application angle for the development on new Drop-on-Demand (DOD) printhead using a fiber-in-a-tube platform[1] to print highly viscous materials[2]. To control the drop formation and manipulation on fiber, one needs to know how the fiber wetting properties and the fiber diameter influence drop formation. And then, one needs to know the effects of fiber movement in the device on drop formation. These two questions constitute the main theme of this dissertation.

Before this study, it was accepted that the liquids could not form axisymmetric droplets if …

Characterization Of Thermal Gelation Properties In Bioresorbable Thermally Activated Hydrogel Polymers For Hernia Surgery Applications, Alexander Mayfield

All Theses

Hydrogel adhesives are a new class of materials with excellent biocompatibility, which makes them very attractive for biomaterial applications. It has been previously shown that Tetronic T1107, a four-arm poly (propylene oxide)-poly (ethylene oxide) (PPO-PEO) block copolymer, is useful as a chemical crosslinking thermo-responsive hydrogel for bioadhesive applications. The end groups of this polymer are modified with acrylate and N-hydroxysuccinimide (NHS) functional groups. The acrylate end group gives the polymer cohesive properties with long-range chemical crosslinking using dithiothreitol (DTT), while the NHS end group gives the polymer adhesive properties through bonding with amines found in organic tissue. It was found …

3d Printed Multicomponent Polymer Based Materials Via Hybrid Filaments: Fabrication And Characterization, Erik Antonio

All Dissertations

Additive manufacturing, also known as 3D printing, promises a manufacturing revolution for both industry and academic circles. One of the most widely used method of 3D printing is Fused Deposition Modeling (FDM) or Fused Filament Fabrication (FFF), which requires a thermoplastic filament to be directed towards a heating block and then deposited via extrusion layer by layer to produce a finished part. However, there are significant issues with this technology, mainly a limitation on the materials available for use and mechanical property deficiencies when compared to traditional manufacturing. These issues are brought about by the temperature limited nature of the …

Creep Behavior Of A Ti-Based Multi-Principal Element Alloy, Benjamin Elbrecht

All Theses

Abstract

The understanding of microstructural damage mechanisms is the foundation of better understanding existing materials and future material development. There are significant challenges to measuring these damage mechanisms in-situ as continuous observation of the state of the microstructure is difficult or impossible for many experimental setups. This thesis presents a method for measuring grain boundary sliding (GBS) and local strain concentrations in-situ via a Heaviside function based algorithm. GBS is the shearing of two grains along their shared grain boundary and is a common damage mechanism in creep which presents as a discontinuity that can be measured with a Heaviside …

Computational Characterization Of Nonwoven Fibrous Materials: Transport And Wetting Properties, Fang Wang

All Dissertations

Nonwoven fibrous materials represent a platform of flexible material substrates. Nonwovens are widely used in the production of napkins, paper, filters, wound covers and face masks. In addition, for many applications, nonwoven materials interact with fluids. For example, in filtration applications, nonwoven materials are used to clean fluids containing solid particles or emulsified droplets. The filtration performance is affected not only by the geometrical arrangement of fibers in non-woven materials but also wettability of fibers. Understanding the transport properties of nonwoven materials and interactions between the dispersed droplets and solid substrate is crucial for the design and optimization of filter …

Modeling Phase Behavior And Agglomeration In Polymer Systems Incorporating Complex Architectures: From Bottlebrush To Lysozyme, Sidong Tu

All Dissertations

Using computational modeling, we focus on the phase behavior of multicomponent systems incorporating enzyme and bottlebrush polymers where the agglomeration of multiple components occurs. We start with all-atom molecular dynamics (MD) simulations of lysozyme and polyethylene glycol (PEG) based polymer mixture to understand the mechanisms of preservation of lysozyme bioactivity at high temperatures with addition of PEG-derived bottlebrushes. We show that the PEG part of bottlebrushes phase separates at high temperature and shells the access of water to lysozyme, resulting in the preservation of lysozyme secondary structures. We then developed a coarse-grained model using a Dissipative Particle Dynamics approach to …

Modeling Pattern Formation And Morphology Development In Polymer Networks, Yao Xiong

All Dissertations

Topography and morphology have considerable impacts on the functionalities of soft materials in an entire range of applications from smart optics to tissue engineering. Adapting theoretical and computational approaches, we focus on the dynamics of pattern formation and morphology development in polymer networks. This dissertation starts with studying the dynamical control of pattern formation in confined thermo-responsive poly(N-isopropylacrylamide) (PNIPAAm) gel films. The patterns are formed due to mechanical instabilities. We perform a linear stability analysis and identify the limits of this analysis in predicting pattern formation in gels. We then study the restructuring between patterns and hysteresis phenomena …

Subwavelength Engineering Of Silicon Photonic Waveguides, Farhan Bin Tarik

All Dissertations

The dissertation demonstrates subwavelength engineering of silicon photonic waveguides in the form of two different structures or avenues: (i) a novel ultra-low mode area v-groove waveguide to enhance light-matter interaction; and (ii) a nanoscale sidewall crystalline grating performed as physical unclonable function to achieve hardware and information security. With the advancement of modern technology and modern supply chain throughout the globe, silicon photonics is set to lead the global semiconductor foundries, thanks to its abundance in nature and a mature and well-established industry. Since, the silicon waveguide is the heart of silicon photonics, it can be considered as the core …

Quantum-Mechanical Evaluation Of Defects In Uranium-Bearing Materials, Megan Hoover

All Dissertations

Quantum-mechanical calculations using density functional theory with the generalized gradient approximation were employed to investigate the effects dopants have on the uranium dioxide (UO₂) structure. Uraninite is a common U⁴⁺ mineral in the Earth's crust and an important material used to produce energy and medical isotopes. Though the incorporation mechanism remains unclear, divalent cations are known to incorporate into the uranium dioxide system. Three charge-balancing mechanisms were evaluated to achieve a net neutral system, including the substitution of (1) a divalent cation for a tetravalent uranium atom and oxygen atom; (2) two divalent cations for a tetravalent …

Crack Control And Bond Performance Of Alternative Coated Reinforcements In Concrete, Sachin Sreedhara

All Dissertations

Concrete cracking in structures is a ubiquitous problem which can lead to the deterioration of the structure. Other than affecting the strength aspect of a structure, cracking impacts the serviceability criteria as well. Although cracking phenomenon in any structure is highly inevitable, it has to be minimized in order to maintain a structure’s life effectively. Cracking in reinforced concrete structures is related to the bond strength developed between the bar and the concrete. It also depends on an ability of the bar to resist the stresses due to shrinkage to minimize the crack. Another important aspect is the resistance offered …

Numerical Implementation And Validation Of A Viscoelastic-Plastic Material Model For Predicting Curing Induced Residual Stresses In Adhesive Bonded Joints, Akshat Agha, Fadi Abu-Farha

Publications

One of the main challenges in the joining of multi-material components is the assessment of the nature and magnitude of the residual stresses developing in the adhesive bond during the heat curing manufacturing process. Numerical modeling of these residual stresses can provide insights for making informed decisions related to (i) material substrate properties; (ii) adhesive properties i.e., low, medium, or high stiffness; (iii) bondline geometry i.e., bondline width and bead thickness; (iv) curing cycle characteristics; and (v) fixation design i.e., type, spacing, the number of joints. This work presents a cure history-dependent viscoelastic-plastic material description for the modeling of adhesive …

Insect Antennae As Bioinspirational Superstrong Fiber-Based Microfluidics, Griffin J. Donley

All Theses

Nature is frequently turned to for inspiration for the creation of new materials. Insect antennae are hollow, blood-filled fibers with complex shape, and are cantilevered at the head. The antenna is muscle-free, but the insect can controllably flex, twist, and maneuver it laterally. To explain this behavior, a comparative study of structural and tensile properties of the antennae of Periplaneta americana (American cockroach), Manduca sexta (Carolina hawkmoth), and Vanessa cardui (painted lady butterfly) was performed. These antennae demonstrate a range of distinguishable tensile properties, responding either as brittle fibers (Manduca sexta) or strain-adaptive fibers that stiffen when stretched (Vanessa cardui …

Near-Earth Ion Irradiation Effects On Functional Ceramic Materials: A Combined Experimental-Monte Carlo Approach, William J. Sands

All Theses

The near-Earth space radiation environment is a complex system that creates a harmful environment for materials to operate in. Motivated by the search for using optical defects as an indicator of radiation damage, five single-crystal functional ceramic materials were selected to undergo ion irradiation at conditions found in the near-Earth space environment. Due to the complex nature of ion irradiation effects in ceramic materials, a host of calculations and experimental characterization methods were used. Calculations using the 2013 SRIM code were used to evaluate the ion projected range and the type and number of defects (vacancies) created by ion irradiation. …

A Study On Effect Of Manufacturing Parameters On Morphology Of A356 Aluminum Foam, Nikhil Nanabhau Mahajan

All Theses

Metal foams have shown an excellent promise for usage as multifunctional material concerning research & development in the last 20 years. They provide remarkable mechanical as well as physical properties being lightweight. Open-cell metal foams have already been used in sound and noise absorption. Open-cell metal foams are outstanding for use in heat exchangers, filters, and many more applications, while closed-cell foams show excellent characteristics in impact energy absorptions. Closed-cell metal foams have higher energy absorption than their solid parent metal as they convert most of the impact energy into deformation energy. Metal foams have been used as prominent safeguard …

Reactive Thin Film Polymers And Thin Film Composite Membranes For The Rapid Screening Of Uranium Isotopes, Abenazer W. Darge

All Dissertations

Traditional radiochemistry approaches for the detection of trace-level alpha-emitting radioisotopes in water require lengthy offsite sample preparations and do not lend themselves to rapid quantification. Therefore, a novel platform is needed that combines onsite purification, concentration, and isotopic screening with a fieldable detection system. My dissertation research objective was to develop novel reactive thin polymer films and thin film composite membranes for the selective separation of uranium from environmental water followed by direct isotopic analysis by alpha spectroscopy. Chapter 1 reviews progress made on uranium separation from aqueous matrices and discusses methods used for the determination of isotopic composition.

Chapter …

Porous Silicon Photonics For Label-Free Interferometric Biosensing And Flat Optics, Tahmid Hassan Talukdar

All Dissertations

This dissertation uses porous silicon as a material platform to explore novel optical effects in three domains: (i) It studies dispersion engineering in integrated waveguides to achieve high performance group index sensing. With proper design parameters, the sensor waveguides can theoretically achieve 6 times larger group index shift compared to the actual bulk effective refractive index shift. We demonstrate the guided mode confinement factor to be a key parameter in design and implementation of these waveguides. (ii) It explores multicolor laser illumination to experimentally demonstrate perceptually enhanced colorimetric sensing, overcoming the limitations faced by many contemporary colorimetric sensors. Our technique …

Synthesis Of Monodisperse Nanoscintillators At High Temperatures For Biomedical Relevant Applications, Eric Zhang

All Dissertations

Luminescent sub-100 nm particulates continuously generate immense research interest in the biomedical field for imaging, theranostics, and optogenetics. Conventionally, upconversion nanoparticles or UV activated semiconductors are studied, however these materials are limited by biological barriers such as the skin which reduces the penetration depth of these excitation sources, tissue's auto- fluorescence, and toxicity. One approach to overcome these challenges is to use nanoscintillators (sub-100 nm materials that can generate visible light using high energy excitation sources such as x-rays) which can generate light locally to the human body. Numerous scintillators have been reported since the discovery of x-rays from the …

Investigating The Effects Of Sic Abrasive Particles On Friction Element Welding, Gaurav Awate

All Theses

The growing demands on reducing the harmful emissions from automobiles have forced automakers to reduce the weight of the vehicle. The increasing demands on improving the fuel economy also has challenged automotive manufacturers to make the vehicle as lightweight as possible. However, the challenge is also to ensure that the vehicle meets safety standards. For the vehicle to meet these standards, it needs to be of adequate strength as well. Automotive manufacturers have adopted a strategy of using multi-material construction to achieve the target. But with multi-material construction comes the requirement of advanced joining techniques that are capable of joining …

Mechanochromic Tunable Emissions Of Hydrogel Encapsulated Radioluminescent Crystalline Colloidal Arrays, Sarah Mell

All Theses

Crystalline colloidal arrays (CCAs) are periodic dielectric arrays composed of monodisperse, negatively charged nanoparticles with unique optical characteristics. Poly(styrene-co-propargyl acrylate) (PS-PA) based copolymer nanoparticles synthesized via an emulsion polymerization form the basis of the CCAs in this work. The negatively charged surfaces result in the colloidal nanoparticles self-assembling into a face-centered cubic (fcc) crystal-like structure. The long-range order and spatial periodicity of the array result in a rejection wavelength, characteristic of CCAs, in which a specific wavelength of light is forbidden from propagating throughout the optical system. The CCAs exhibit mechanochromism through a rejection wavelength shift corresponding to a change …

Extractive Membranes For The Detection And Screening Of Waterborne Plutonium, James Foster

All Dissertations

The development of rapid screening tools for special nuclear materials remains a crucial focus for nonproliferation efforts. Traditional approaches for the analysis of trace-level Pu isotopes in water requires tedious and time-consuming sample preparation steps that do not lend well to expeditious screening. Therefore, a novel analytical method that combines both Pu concentration and source preparation into a single detection system would make for an invaluable tool for nuclear security applications. Extractive membranes absorbers can help to fulfill this role as they are capable of concentrating Pu to detectable limits while subsequently serving as alpha spectrometry sample sources. In Chapter …

Sustainable Composites From Agricultural And Petroleum Waste, Menisha S. Karunarathna

All Dissertations

Green gas emission has been a pervasive and persistent subject of debate for a prolonged period. The soaring number of industries and vehicle fuel emissions presage a concomitant rise in global CO₂ emissions. Global cement production is responsible for 8% of the total CO₂ release, yet, the production continues due to the surging demand. Hence, there is an ongoing quest to find alternatives for cement and building materials produced with zero to lower CO₂ emissions. The work presented in this dissertation focuses on finding recyclable, zero CO₂ gas-producing high sulfur biocomposites materials, which can compete with …

Graphene Oxide-Thermoplastic Nanocomposites: Fabrication And Properties, Seyedeh Mastooreh Seyedi Ghezghapan

All Dissertations

Polymer nanocomposites are used for a wide variety of applications. These nanocomposites can have a number of important characteristics depending on the nature of the nanomaterial, its size, volume fraction, its distribution, and interactions within the host polymer. Mechanical strength, thermal and electrical conductivity are some of these materials' most focused and studied features. Besides the positive influences of the reinforcements, nanomaterials also might have some adverse impacts on the polymer matrix. These issues could arise from the aggregation of the fillers and the poor interfacial interactions of the components. Several approaches are introduced to modify the nanofillers and enhance …

Synthesis And Molecular Processes Governing Self-Healing Polymeric Materials, Siyang Wang

All Dissertations

Self-healing polymers capable of recovering from physical damages are promising materials for advanced technologies. In these studies, we developed routes to achieve self-healable properties in acrylic-based copolymers that rely on non-covalent dipolar interactions present in essentially all polymeric materials. Using a combination of spectroscopic tools, thermo-mechanical analysis, and molecular dynamic (MD) simulations, these studies have shown that dipolar interactions lead to conformational changes of macromolecular segments which, in turn, result in self-healing without external intervention. This dissertation also describes the development of novel self-healable acrylic-based covalent adaptable networks (CANs) that combine reprocessing and self-healing properties. The utilization of dipolar interactions …

Thermoforming Process Effects On Structural Performance Of Carbon Fiber Reinforced Thermoplastic Composite Parts Through A Manufacturing To Response Pathway, Madhura Limaye, Sai Aditya Pradeep, Anmol Kothari, Sushil Savla, Akshat Agha, Srikanth Pilla, Gang Li

Publications

Thermoforming process of thermoplastic-based continuous CFRP's offer a major advantage in reducing cycle times for large-scale productions, but it can also have a significant impact on the structural performance of the parts by inducing undesirable effects. This necessitates the development of an optimal manufacturing process that minimizes the introduction of undesirable factors in the structure and thereby achieves the targeted mechanical performance. This can be done by first establishing a relationship between the manufacturing process and mechanical performance and successively optimizing it to achieve the desired targets. The current study focuses on the former part, where a manufacturing-to-response (MTR) pathway …

Understanding Process-Structure-Property-Performance Relationships Of Thermoplastic Olefins (Tpo) Foams Through A Novel Manufacturing To Response Pathway, Sai Aditya Pradeep

All Dissertations

The global transportation industry is the second highest contributor to climate change. As a result, there has been a concerted effort to spearhead research in economical lightweighting technologies, as every 10 % reduction in weight will lead to to 6 – 8 % improvement in fuel efficiency. Additionally, the recent push for electrification and the emphasis on Corporate Average Fuel Economy (CAFE) standards have seen original equipment manufacturers (OEM’s) dive into lightweighting of materials to improve overall range and/or fuel-efficiency. Thermoplastic Olefins (TPOs) have in recent years carved out a niche in the automotive industry due to advantages such as …

Deep Learning-Guided Prediction Of Material’S Microstructures And Applications To Advanced Manufacturing, Jianan Tang

All Dissertations

Material microstructure prediction based on processing conditions is very useful in advanced manufacturing. Trial-and-error experiments are very time-consuming to exhaust numerous combinations of processing parameters and characterize the resulting microstructures. To accelerate process development and optimization, researchers have explored microstructure prediction methods, including physical-based modeling and feature-based machine learning. Nevertheless, they both have limitations. Physical-based modeling consumes too much computational power. And in feature-based machine learning, low-dimensional microstructural features are manually extracted to represent high-dimensional microstructures, which leads to information loss.

In this dissertation, a deep learning-guided microstructure prediction framework is established. It uses a conditional generative adversarial network (CGAN) …

Glycan Functionalization Of Iron Oxide Nanoparticles (Ionps) As A Method Of Inactivating Antibiotic Resistant Neisseria Gonorrhoeae Via A Magnetically Mediated Energy Delivery (Magmed) System, Cedric Taylor

All Theses

With the increase of antibiotic resistant bacteria, current established therapeutic treatment methods are rapidly demonstrating decreasing efficacy. For this project, we are studying a novel alternate mechanism of treating antibiotic resistant bacteria by utilizing magnetic iron oxide nanoparticles (IONPs) coated with a heterobifunctional polyethylene glycol polymer (PEG) and functionalized with glycan structures that can interact with Neisseria gonorrhoeae FA1090. Interaction between the IONPs and bacteria is manipulated by an external alternating magnetic field (AMF) in a process known as magnetically mediated energy delivery (MagMED). Magnetic IONPs were synthesized and reacted with PEG (PEG-IONPs) and functionalized with glycans Gal(α1-3)Gal(β1-4)Glc(β1-1) (common name: …

Development Of Lambda Factors For Masonry Design With Lightweight Grout, Rumi Shrestha

All Theses

Reduction in structural mass, improvement in thermal performance, and reduction in shrinkage cracking through internal curing are some of the reasons that lightweight (LW) aggregates have been used in structures and pavements for decades. However, lightweight grout is still not permitted for use in reinforced masonry construction by the TMS 402/602-16 code. In order to realize the benefits of lightweight grout in U.S. reinforced masonry construction, a codified procedure for its use is required which must be informed by experimental testing.

This research is a pilot project directed to characterize the performance of LW grout in comparison to normal weight …

Mechanical Interfacial Locking And Multiscale Modeling Of Reinforced Thermoplastic Composites For Structural Applications, Anmol Kothari

All Dissertations

The ever-growing pressure of reducing the adverse impact of transportation systems on environment has pushed industries towards fuel-efficient and sustainable solutions. While several approaches have been used to improve fuel efficiency, the light-weighting of structural components has proven broadly effective. In this regard, reinforced thermoplastic composites (RTPC), owing to their high recyclability, higher impact strength and fast cycle times, have become competitive candidates at an industrial scale. However, to implement RTPC toward large scale structural applications several challenges pertaining to material design and manufacturing effects need to be addressed. To this end, a computational study is carried out to address …