Materials Science and Engineering Commons^™

Radiation Exposure Calibration Of The Al2o3:C With Radium-226 And Cesium-137 Using The Osl Method, Selma Tepeli Aydin

All Theses

Optically stimulated luminescence (OSL) dosimetry was utilized to calibrate Al₂O₃:C powder dosimeters, available commercially as the nanoDot® from Landauer Inc., and compare the dosimeter response to radium-226 (²²⁶Ra) and cesium-137 (¹³⁷Cs). The signal from the OSL was quantified using a microSTARii^® OSL reader also produced by Landauer Inc. Dose-response curves were developed for ²²⁶Ra and ¹³⁷Cs experiments (5 dosimeters each) at thirteen absorbed doses. Individual dosimeter response was tracked by serial number. Linear regression analysis was performed to determine if there were significant differences between the intercepts of the …

Cfrp Delamination Density Propagation Analysis By Magnetostriction Theory, Brandon Eugene Williams

All Dissertations

While Carbon Fiber Reinforced Polymers (CFRPs) have exceptional mechanical properties concerning their overall weight, their failure profile in demanding high-stress environments raises reliability concerns in structural applications. Two crucial limiting factors in CFRP reliability are low-strain material degradation and low fracture toughness. Due to CFRP’s low strain degradation characteristics, a wide variety of interlaminar damage can be sustained without any appreciable change to the physical structure itself. This damage suffered by the energy transfer from high- stress levels appears in the form of microporosity, crazes, microcracks, and delamination in the matrix material before any severe laminate damage is observed. This …

Material World, Nicole Weldy

All Theses

My thesis, Material World, delves into the use of the crochet unit as a construction technique for building forms. Through this, I aim to organize different materials in a way that responds to the challenges posed by the physical world. My artistic process is centered around honoring the inherent qualities of thread and uses these qualities to create form, lightness, and linearity. At the same time, I remain receptive to transformative processes such as combining three-dimensional (3D) printed lines and lace stiffener to push the boundaries of what thread can do. By combining manual craftsmanship with technology materialized as …

A Transport Property-Based Assessment Of Triple Ionic-Electronic Conductors As Cathodes For Protonic Ceramic Fuel Cells, Jack Harrison Duffy

All Dissertations

Triple ionic-electronic conductors (TIECs) are a widely studied class of materials for electrodes in ceramic electrochemical devices such as protonic ceramic fuel cells. These ceramics are perovskite-based and exhibit concurrent conductivity of protons, oxide ions, and electrons at elevated temperatures. Despite their numerous references in literature, few studies have systematically probed the fundamental surface- and bulk-level properties of TIECs. In this dissertation, dopant levels are systematically altered in the BaCo_0.4Fe_0.4Zr_0.1Y_0.1O_3-δ-type perovskite TIEC to reveal the effects on structure, transport properties, and durability of each material. The results of this work …

Glass Bubbles Grafted With Polymer Brushes For Liquid Hydrocarbon Fire Extinguishment, Randall Snipes

All Dissertations

The current most efficient solution to fighting liquid pool fires involves the use of firefighting foams containing fluorinated surfactants. The physiochemical properties of these foams are considerably different to all other currently available firefighting foams. Fluorinated surfactants lower the surface tension to a point where the foam solution draining from the foam structure forms a continuous aqueous film on the surface of a volatile hydrocarbon fuel, adding an additional barrier to fuel vapor diffusion to the burning fire. For this reason, these foams qualify as aqueous film forming foams (AFFFs). However, fluorinated compounds are extremely harmful for the environment due …

Life Cycle Energy Assesment Of Advanced Fiber Reinforced Composite Design And Manufacturing Methodologies, Urjit Lad

All Theses

Automotive industry at large is focused on vehicle light-weighting since a 6%-8% increase in fuel efficiency can be achieved with a 10% reduction in vehicle weight [1]. With the growing demand for cost-effective and sustainable light weighting of automobile structures, interest has increased in the application of fiber reinforced plastic (FRP) composites for use in the Body-in-White (BiW), which can account for up to 40% of the total vehicle weight. Traditional FRP composite manufacturing processes like vacuum assisted resin transfer molding, autoclave consolidation or use of automated fiber placement have been successfully used for marine and aerospace applications. However, these …

Multiscale Modeling And Gaussian Process Regression For Applications In Composite Materials, Joshua Arp

All Dissertations

An ongoing challenge in advanced materials design is the development of accurate multiscale models that consider uncertainty while establishing a link between knowledge or information about constituent materials to overall composite properties. Successful models can accurately predict composite properties, reducing the high financial and labor costs associated with experimental determination and accelerating material innovation. Whereas early pioneers in micromechanics developed simplistic theoretical models to map these relationships, modern advances in computer technology have enabled detailed simulators capable of accurately predicting complex and multiscale phenomena.

This work advances domain knowledge via two means: firstly, through the development of high-fidelity, physics-based finite …

Integrating Sensor Development, Risk Assessment, And Community Engagement To Support Environmental Justice In The Rural Community Of El Tiple, Colombia, David Bahamon Pinzon

All Dissertations

In Colombia, ethnic communities have traditionally been responsible stewards of natural resources. They recognize the importance of these resources for their livelihood, as well as their ancestral and cultural heritage. El Tiple, a rural Afro-Colombian community, has been affected by the incursion of private corporations that promoted the expansion of sugarcane monocrops in their territory. Since the introduction of the monoculture industry, local freshwater sources have been depleted due to intensive water use for irrigation of the sugarcane crops. Additionally, the intensive usage of agrochemicals has been linked with loss of native flora, damages to family farms, and pollution of …

Preparation Of High Entropy Titanite Pyrochlore And Radiation Stability Study, Adam Gootgeld

All Theses

Pyrochlore has been studied as a host phase for safe storage of radionuclides and exists naturally with long-term stability with good long-range order [1]. High entropy oxides show promising tunable properties that could demonstrate favorable bulk deposit of radioactive materials such as spent nuclear fuel (Uranium and other actinides). It is proposed that using high entropy oxides (HEOs) as the cation in this framework will shift the gibbs free energy so that radioactive nuclear waste will be stabilized for safe, long-term, eco-friendly storage. We have established a consistent method to fabricate high entropy titanite pyrochlores. In this study, ion beam …

Characterization Of Mechanically Recycled Polylactic Acid (Pla) Filament For 3d-Printing By Evaluating Mechanical, Thermal, And Chemical Properties And Process Performance, Mahsa Shabani Samghabady

All Theses

Polylactic acid (PLA) is a biopolymer made from renewable resources such as sugar and corn. PLA filament is a popular material used in Fused Deposition Modeling (FDM) 3D-printing. While this material has many advantages, all the failed parts, support structures, rafts, nozzle tests, and the many prototype iterations during the 3D-printing process contribute to the plastic pollution and release of greenhouse gases. Although PLA is biodegradable, it can take years to degrade in landfills. Instead of throwing away PLA waste and buying new filaments, PLA can be recycled. Amongst the different recycling technologies, mechanical recycling is the most environmentally friendly. …

Carbon Fibers From Athabasca Oil-Sand Asphaltenes, Blake Reardon

All Theses

Carbon fibers possess ultra-high specific strength and modulus. Therefore, the material is popular in aerospace, automotive, and sports industries. Approximately 95% of all carbon fibers are spun from a high-cost precursor, polyacrylonitrile (PAN). There is a need for a cheaper grade of carbon fiber for low-cost applications because about half of carbon fiber cost is associated with precursor cost. A promising alternative to the high-cost PAN precursor is petroleum-based asphaltene. Asphaltenes are highly aromatic and have a high carbon content but lack the purity of the PAN precursor. Processes like the molten- sodium desulfurization upgrading have been used to harvest …

Processing, Microstructure, And Properties Of Alumina Ceramics And Silica Glass During Laser Selective Additive/Subtractive Manufacturing, Xiao Geng

All Dissertations

The heterogeneous structure is essential to obtain excellent performance in many ceramics or glass devices/components. Conventional fabrication on these heterogeneous structure composites usually requires multiple treatments, specific molds for certain structures, and post-processing to get desired structure and properties. Therefore, the flexibility of the structure is limited, and a long fabrication time is required.

Integrated additive/subtractive manufacturing and laser-based technologies have caught researchers` attention in ceramics/glass heterogeneous structure fabrication. This is because the integration of additive manufacturing (AM) with subtractive manufacturing (SM) not only maintained the advantages of AM in rapid prototyping, design complexity, and reduced material wastage but also …

An In Vivo Biocompatibility Analysis Of A Novel Tissue Regeneration Matrix Using A Pig Model, Shamar Thomas

All Theses

The goal of this project is to develop an injectable bead scaffold to promote tissue regeneration in the void created by lumpectomy and to alleviate post lumpectomy problems by preventing local recurrence and minimizing surgical-related infections. Microbeads were synthesized from collagen type I and crosslinked with tannic acid to form the basis for this injectable therapeutic. Tannic acid acts as a therapeutic anticancer agent. The action mechanisms of tannins in breast cancer cells have been studied with studies showing tannins to be cytotoxic to cancer cells in a dose-dependent manner. Tannic acid induces apoptosis in breast cancer cells via caspase …

Iii-Nitride Triangular Microcantilevers For Multimodal Sensing Applications, Balaadithya Uppalapati

All Dissertations

Micro-electromechanical systems (MEMS)-based sensors have gained significant attention due to their ability to sense, measure, and process various physical, chemical, and biological parameters. The small size of MEMS sensors provides numerous advantages, including low power consumption, high sensitivity, and rapid response time, making them suitable for various applications in healthcare, automotive, aerospace, and consumer electronics.

In the past few years, AlGaN/GaN MEMS devices have been found to offer several advantages over silicon-based MEMS devices. One of the main advantages of AlGaN/GaN MEMS is their high sensitivity to surface stresses and forces due to their high piezoelectric coefficients. This sensitivity allows …

Mesoscale Modeling And Machine Learning Studies Of Grain Boundary Segregation In Metallic Alloys, Malek Alkayyali

All Dissertations

Nearly all structural and functional materials are polycrystalline alloys; they are composed of differently oriented crystalline grains that are joined at internal interfaces termed grain boundaries (GBs). It is well accepted that GB dynamics play a critical role in many phenomena during materials processing or under operating environments. Of particular interest are GB migration and grain growth processes, as they influence many crystal-size dependent properties, such as mechanical strength and electrical conductivity.

In metallic alloys, GBs offer a plethora of preferential atomic sites for alloying elements to occupy. Indeed, recent experimental studies employing in-situ microscopy revealed strong GB solute segregation …

Machine Learning-Based Data And Model Driven Bayesian Uncertanity Quantification Of Inverse Problems For Suspended Non-Structural System, Zhiyuan Qin

All Dissertations

Inverse problems involve extracting the internal structure of a physical system from noisy measurement data. In many fields, the Bayesian inference is used to address the ill-conditioned nature of the inverse problem by incorporating prior information through an initial distribution. In the nonparametric Bayesian framework, surrogate models such as Gaussian Processes or Deep Neural Networks are used as flexible and effective probabilistic modeling tools to overcome the high-dimensional curse and reduce computational costs. In practical systems and computer models, uncertainties can be addressed through parameter calibration, sensitivity analysis, and uncertainty quantification, leading to improved reliability and robustness of decision and …

Classification Of Electrical Current Used In Electroplastic Forming, Tyler Grimm

All Dissertations

Electrically assisted manufacturing (EAM) is the direct application of an electric current to a workpiece during manufacturing. This advanced manufacturing process has been shown to produce anomalous effects which extend beyond the current state of modeling of thermal influences. These purported non-thermal effects have collectively been termed electroplastic effects (EPEs).

While there is a distinct difference in results between steady-state (ideal DC) testing and pulsed current testing, the very definition of these two EAM methods has not been well established. A "long" pulse may be considered DC current; a "short" pulse may produce electroplastic effects; and even "steady-state" current shapes …

Elucidating The Mechanical And Transport Properties Of Lignin-Based Hydrogel Composites, Nicholas Gregorich

All Dissertations

The use of lignin in the fabrication of soft composites has become an emerging area of research in polymer science and polymer chemistry. These lignin-based materials present numerous benefits, notably, a reduction in the use of petroleum-based precursor, improved structural benefits to otherwise soft host polymers, as well as the inherent antimicrobial and antioxidant properties of lignin, making it suitable for biomaterials. Herein, we present two chemical reaction pathways of incorporating lignin that was fractionated and cleaned using the Aqueous Lignin Purification with Hot Agents (ALPHA) process into poly(vinyl alcohol) (PVA) hydrogel composites for aqueous-based separations. By leveraging the ALPHA …

Molecular Dynamics Simulation On Molybdenum Disulfide: Thermal-Mechanical Properties And Phase Transitions Under External Loading, Mahabubur Rahman

All Dissertations

Due to their remarkable properties, transition metal dichalcogenides (TMDs) have received much scientific interest throughout the past decade. Two layers of chalcogen atoms (S, Se, Te) sandwich a layer of transition metal atoms (Mo, W, Ta) to form the three-atom thick unit cell in TMDs. The interaction between TMD "single layers" is mediated by neighboring chalcogen planes and bonded by Van der Waals forces. Due to this weak out-of-plane interaction, bulk samples can be thinned down to a single layer by exfoliation. Among the TMDs, Molybdenum Disulfide (MoS₂) shows promise in the field of electronics, optics, and sensing …

Mesoscale Modeling Of Controlled Degradation In Polymer Networks And Melts, Vaibhav Palkar

All Dissertations

Controlled degradation of polymers finds various applications in fields ranging from the design of functional soft materials to recycling of polymers. In several of these applications, the characteristic length scale at which relevant processes occur ranges from nanometers to microns, typically referred to as the mesoscale. Although analytical models and continuum approaches inform our current understanding, analysis of degradation at the mesoscale is exceptionally limited. For modeling degradation at the mesoscale, we use the Dissipative Particle Dynamics (DPD) technique and the LAMMPS simulation software. Within the DPD framework, we model controlled degradation or the breaking of covalent bonds within a …

Iron Phosphate Glass For The Immobilization Of Dehalogenated Salt Waste, Matthew Aaron Page

All Theses

Electrochemical reprocessing can be used to recycle presently stored nuclear fuel and consists of dissolving that used fuel in molten salt and the waste produced from these processes is a small amount of a high-level salt waste. Vitrification has been selected as the primary means of safely disposing high and low level radioactive waste. This is due to glass’ ability to incorporate many elements within its matrix, and it is chemically durable with the addition of network formers and other glass forming chemicals. With over 90,000 tonnes of nuclear waste in the United States, the avoidance of additional steps required …

Design, Fabrication, And Characterization Of Conjugated Polymeric Electrochemical Memristors As Neuromorphic/Integrated Circuits, Benjamin Grant

All Dissertations

Organic materials are promising candidates for future electronic devices compared to the complementing inorganic materials due to their ease of processability, use, and disposal, low cost of fabrication, energy efficiency, and flexible nature toward implementation as flexible and non-conformal devices.With that in mind, electrochemical materials have been widely demonstrated with commercial use as sensors, displays, and a variety of other electronic devices. As Moore's law predicts the increase in the density of transistors on a chip, the requirement to create either smaller transistors or the replacement of the transistor device entirely is apparent. Memory resistors, coined ``memristor", are variable resistive …

Effects Of Surface Noise On Printing Artifacts: An Artistic Approach To Hiding Print Artifacts, Samuel New

All Theses

This research focuses on improving the quality of Fused Filament Fabrication (FFF) 3D printing by using fractal noise to mask certain print artifacts (e.g. layer lines and stair-stepping). The use of textures is quite common in digital sculpting for aesthetic reasons. This study focuses on finding specific textures that minimize visible 3D print artifacts.

Effects Of Polymer Side-Group Size On Interfacial Mechanics Of Graphene-Polymer Nanocomposites, Grace Brokaw

All Theses

Graphene-reinforced polymer nanocomposites possess excellent mechanical, thermal, and electrical properties, which make them promising candidates for various applications. Favorable interfacial interactions and mechanics between graphene sheets and polymer matrices are often essential to achieve superior mechanical properties. Nevertheless, it remains largely elusive how molecular features of polymer systems, particularly the side-group size of polymer chains, affect the interfacial mechanics between graphene sheets and polymer matrices, primarily due to challenges in well controlling these features in experiments. On the other hand, exploring their roles in the mechanical properties of graphene-polymer nanocomposites is very expensive to study with all-atomistic molecular dynamics (MD) …

An Application Of Optimized Bistable Laminates As A Low Velocity, Low Impact Mechanical Deterrent, Graham Lancaster

All Theses

This research considers the problem of using bistable laminates as a mechanical deterrent to the impending impact of a particle. The structure will be controlled through an algorithm that will utilize piezoelectric devices to activate them in unison with the bistable laminate to successfully deter. A novel experimental setup will be constructed to ensure that the bistable laminate stays fixed when acting as a mechanical deterrent. Piezoelectricity is the main driving force of the bistable laminate to morph and this study will use a Macro Fiber Composite (MFC) actuator that contains piezoelectric ceramic rods in a patch to transfer electrical …

Enhancing The Performance Of Poly(3-Hexylthiophene) Based Organic Thin-Film Transistors Using An Interface Engineering Method, Eyob Negussie Tarekegn

All Dissertations

An original design and photolithographic fabrication process for poly(3-hexylthiophene-2, 5-diyl) (P3HT) based organic thin-film transistors (OTFTs) is presented. The structure of the transistors was based on the bottom gate bottom contact OTFT. The fabrication process was efficient, cost-effective, and relatively straightforward to implement. Current–voltage (I-V) measurements were performed to characterize the primary electronic properties of the transistors. The measured mobility of these transistors was significantly higher than most results reported in the literature for other similar bottom gate bottom contact P3HT OTFTs. The higher mobility is explained primarily by the effectiveness of the fabrication process in keeping the interfacial layers …

Carbon Fibers From Bio-Based Precursors Derived From Renewable Sources, Sagar Kanhere

All Dissertations

Carbon fibers have the highest strength and modulus among all known fibers and are used as reinforcements in high-performance composites [1]. Carbon fibers also have a very low density relative to metals. Therefore, carbon fibers possess ultrahigh specific strength and modulus, which make them desirable for high-performance light-weight composites. A vast majority of commercial carbon fibers are produced from PAN precursors that are expensive, which limits the use of PAN-derived carbon fibers to aerospace applications (e.g., airplanes). However, for costsensitive applications, there is a need for low-cost, moderate performance carbon fibers. Lignin is a low-cost by-product of pulping and biorefining …

Active Rheological And Stiffening Control Of Cementitious Systems For Additive Manufacturing, Abdul Basit Peerzada

All Dissertations

Technological advancements and automation in the last two decades have made additive manufacturing of cementitious systems a reality. Among all the additive manufacturing techniques used for cementitious materials, layer-by-layer extrusion-based printing is the most used technique. For a layer-by-layer printing process, the requirements of cementitious materials vary from those of a conventional construction process. Typically, the cementitious materials are pumped to a print head using a positive-displacement pump. The pumpability of the cementitious material for a specific pumping system depends on its rheological properties. For effective pumping, the yield stress and plastic viscosity of a cementitious system should be low. …

Design And Development Of A Multi-Material, Cost-Competitive, Lightweight Mid-Size Sports Utility Vehicle’S Body-In-White, Amit M. Deshpande, Rushabh Rajesh Sadiwala, Nathan Brown, Sai Aditya Pradeep, Leon M. Headings, Ningxiner Zhao, Brad Losey, Ryan Hahnlen, Marcelo J. Dapino, Gang Li, Srikanth Pilla

Publications

Vehicle light-weighting has allowed automotive original equipment manufacturers (OEMs) to improve fuel efficiency, incorporate value-adding features without a weight penalty, and extract better performance. The typical body-in-white (BiW) accounts for up to 40% of the total vehicle mass, making it the focus of light-weighting efforts through a) conceptual redesign b) design optimization using state-of-the-art computer-aided engineering (CAE) tools, and c) use of advanced high strength steels (AHSS), aluminum, magnesium, and/or fiber-reinforced plastic (FRP) composites. However, most of these light-weighting efforts have been focused on luxury/sports vehicles, with a relatively high price range and an average production of 100,000 units/year or …

Modeling Hierarchical Porous Electrodes With Tailored Anisotropic Structure, Debanjan Sarker

All Theses

Modern electric vehicles and consumer electronics applications demand high specific energy from Li-ion batteries, which can be charged and discharged faster. In the search for high specific energy, researchers have tried to make thicker battery electrodes which contain a greater proportion of active material. While chemical and structural modification of electrodes can help to increase the electronic conductivity of active material, the microstructure of porous electrodes can be engineered to enhance ion transport for fast charge and discharge. Previous research has shown that macropores introduced by directional freeze tape casting can enhance the performance of thick porous electrodes. For instance, …