Materials Science and Engineering Commons^™

Development Of Fiber-Optic Humidity Sensor Probe With Gelatin Cladding, Akhiruddin Maddu, Kun Modjahidin, Sar Sardy, Hamdani Zain

Makara Journal of Technology

Development of Fiber-Optic Humidity Sensor Probe with Gelatin Cladding. Humidity sensor based on optical fiber with gelatin cladding has been developed. In this humidity sensor probe, the origin cladding of optical fiber is replaced by gelatin coating as humidity sensitive cladding. Testing of the optical fiber sensor probe was conducted by measuring of light intensity transmitted on the optical fiber probe for each variation of different humidity treatments. Response of the optical fiber sensor probe measured from 42%RH to 99%RH, the results show an optical transmission curve varied with relative humidity (RH). Optical transmission in the optical fiber probe increase …

On The Performance Of Imt-2000 Communication Link Based On Stratospheric Platforms, Iskandar Iskandar, Shigeru Shimamoto

Makara Journal of Technology

A new means for providing wireless communication has been currently proposed. It is based on aerial vehicle known as High Altitude Platform or Stratospheric Platforms (SPF). The SPF will be operated at an altitude of 17-22 km above the ground. Therefore, the channel condition may be different compared with those of the conventional terrestrial or satellite wireless channel. In this paper, the channel propagation characteristic of such a system is firstly investigated by means of ray tracing algorithm. We emphasize our investigation in a typical urban environment, in which the mobile users mostly exist. We developed building block model for …

Analysis Of Technical Energy Losses By Using Simulation, Betrianis Betrianis, Randite Herawan

Makara Journal of Technology

Model is a representation of a system. Through model, it can be easier to forecast and control the changing of each element system. Electricity distribution is also a system. Losses are general problem that exist in a distribution network system. But with the right methods, specifically technical energy losses can be reduced in order to increase the efficiency. By making model of the distribution network, the value of technical energy losses in the whole network as well as in every line can be observed. Simulation can also be used to see all losses reduction alternatives. By comparing results from each …

Modeling Of Coupled-Tank System Using Fuzzy Takagi-Sugeno Model, Aries Subiantoro

Makara Journal of Technology

Modeling of Coupled-Tank System Using Fuzzy Takagi-Sugeno Model. This paper describes modeling of coupledtank system based on data measurement using fuzzy Takagi-Sugeno model. The fuzzy clustering method of Gustafson- Kessel algorithm is used to classify input-output data into several clusters based on distance similarity of a member of input-output data from center of cluster. The formed clusters are projected orthonormally into each linguistic variables of premise part to determine membership function of fuzzy Takagi-Sugeno model. By estimating data in each cluster, the consequent parameters of fuzzy Takagi-Sugeno model are calculated using weighted least-squares method. The resulted fuzzy Takagi-Sugeno model is …

Design Of Induction Motor Drive Without Velocity Sensor Using Current Vector Controller With Full And Reduced Observer Moving To Dq Axis, Ridwan Gunawan, Feri Yusivar, Wahidin Wahab, Zuhal A. Kadir

Makara Journal of Technology

Design of Induction Motor Drive Without Velocity Sensor Using Current Vector Controller with Full and Reduced Observer Moving to DQ Axis. The observer is used in estimation velocity sensor usually in α-β axis, therefore this situation will need an extra transformation when we want to add compensator because the flux model is in direct and quadrature-axis dq. Every used the transformation to make possible emerge an error. So in this simulation is used a method to estimate the velocity of induction motor drive with observer that is moved to dq-axis. The model of actual motor used is in alfa-beta axis, …

Hybrid Identification System With Arx And Fast Fourier Transform In Application Of A Quarter Of Vehicle Half Active Suspension, Noveri Lysbetti M, Antonius R.

Makara Journal of Technology

Hybrid Identification System with ARX and Fast Fourier Transform in Application of a Quarter of Vehicle Half Active Suspension. In a control system problem, identification system mechanism is a absolute thing, especially in adaptation controlling to disturbance changing. For that case, is needed an identification method which can identify the changing of disturbance in that system. The aim of this research is to give an alternative in system/plant identification which is a combination (hybrid) of ARX and Fast Fourier Transform. So, it is needed an algorithm design for identification process. In this case, the designed algorithm will be implemented in …

Characterization Of Stress In Gan-On-Sapphire Microelectromechanical Systems (Mems) Structures Using Micro-Raman Spectroscopy, Francisco E. Parada

Theses and Dissertations

Micro-Raman (µRaman) spectroscopy is an efficient, non-destructive technique widely used to determine the quality of semiconductor materials and microelectromechanical systems. This work characterizes the stress distribution in wurtzite gallium nitride grown on c-plane sapphire substrates by molecular beam epitaxy. This wide bandgap semiconductor material is being considered by the Air Force Research Laboratory for the fabrication of shock-hardened MEMS accelerometers. µRaman spectroscopy is particularly useful for stress characterization because of its ability to measure the spectral shifts in Raman peaks in a material, and correlate those shifts to stress and strain. The spectral peak shift as a function of stress, …

High Temperature Heat Exchanger Project: Quarterly Progress Report October 1, 2005 Through December 31, 2005, Anthony Hechanova

Publications (NSTD)

• Liquid Salt Technical Working Group Meeting. The first meeting of the Liquid Salt Technical Working Group was held on October 28, 2005 at the Pratt Whitney Rocketdyne facility in Canoga Park, CA. 20 experts from academia, industry, and national laboratories participated to discuss current state of knowledge and research needs for high temperature liquid salt applications.
• Nuclear Hydrogen Initiative Semi-annual Review. Several participants from the UNLVRF University Consortium gave technical presentations at the NHI Semi-annual Review meeting in Rockville, MD, November 9-10, 2005.
• Quarterly Collaboration Meeting. The University of Nevada, Las Vegas hosted a UNLVRF HTHX Project quarterly meeting December …

Cracking Of Martensitic Alloy Ep-823 Under Controlled Potential, Ajit K. Roy, M. K. Hossain

Mechanical Engineering Faculty Research

The susceptibility of martensitic Alloy EP-823 to stress corrosion cracking was evaluated with and without an applied cathodic potential using the slow-strain-rate (SSR) testing technique. The magnitude of the applied potential was based on the corrosion potential determined by cyclic polarization. The cracking susceptibility in an acidic environment at different temperatures was expressed in terms of the true failure stress (ơ_f), time to failure (TTF), and ductility parameters, including percent elongation (%El) and percent reduction in area (%RA). The data indicate that the magnitudes of ơ_r, TTF, %El, and %RA were reduced due to cathodic charging. …

College Of Engineering Senior Design Competition Fall 2005, University Of Nevada, Las Vegas

Fred and Harriet Cox Senior Design Competition Projects

Part of every UNLV engineering student’s academic experience, the senior design project stimulates engineering innovation and entrepreneurship. Each student in their senior year chooses, plans, designs and prototypes a product in this required element of the curriculum. A capstone to the student’s educational career, the senior design project encourages the student to use everything learned in the engineering program to create a practical, real world solution to an engineering challenge.

The senior design competition helps to focus the senior students in increasing the quality and potential for commercial application for their design projects. Judges from local industry evaluate the projects …

Synthesis Of Fuel Cell Membrane: Copolymerization Of Styrene On Etfe Film By Grafted Pre-Irradiation, Yohan Yohan, Rifai M. Nur, Lilik Hendrajaya, E. S. Siradj

Makara Journal of Technology

Synthesis of Fuel Cell Membrane: Copolymerization of Styrene on ETFE Film by Grafted pre-Irradiation. Preirradiation Grafting styrene monomer on ETFE film has been prepared. Research has been performed by γ-ray radiation at various total dose from 2.5 – 12.5 kGy and various dose rate from 1.3 – 1.9 kGy/hour. Irradiated copolymer is then grafted by styrene monomer in various solvent: ethanol, 2-propanol, and toluene, various concentration from 20 – 70% volume, various temperature from 50 – 90oC, and various grafting time from 2 – 12 hours. The results showed that percent of grafting is increase with increase of total dose …

Design Of Product Placement Layout In Retail Shop Using Market Basket Analysis, Isti Surjandari, Annury Citra Seruni

Makara Journal of Technology

Retailing is an industry with high level of competition. It is a customer-based industry which depends on how it could be aware of what the customers’ needs and requirements are. One technique most used in supermarkets is the mix merchandise. The purpose of this paper is to identify associated products, which then grouped in mix merchandise with the use of market basket analysis. This association between products then will be applied in the design layout of the product in the supermarket. The process of identifying the related products bought together in one transaction is done by using data mining technique. …

Production Hydrogen And Nanocarbon Via Methane Decomposition Using Ni-Based Catalysts. Effect Of Acidity And Catalyst Diameter, Widodo W. Purwanto, M. Nasikin, E. Saputra, L. Song

Makara Journal of Technology

Objectives of this research are mainly to study impacts of acidity strength (by varying amount of precipitant and loading Al-Si) and the effect of nickel particle size (by varying calcinations temperature) on decomposition reaction performances. In this research, high-nickel-loaded catalyst is prepared with two methods. Ni-Cu/Al catalysts were prepared with co-precipitation method. While the Ni-Cu/Al-Si catalyst were prepared by combined co-precipitation and sol-gel method. The direct cracking of methane was performed in 8mm quartz fixed bed reactor at atmospheric pressure and 500-700°C. The main results showed that the Al content of catalyst increases with the increasing amount of precipitant. The …

Design And Implementation Of 1-2 Ghz Stepped Frequency Gpr For Buried Metal Detection, Joko Suryana, Andriyan B. Suksmono, Tati R. Mengko

Makara Journal of Technology

Design and Implementation of 1-2 GHz Stepped Frequency GPR for Buried Metal Detection. In this paper, we describe the design and realization steps of 1 – 2 GHz SFGPR (Stepped Frequency Ground Penetrating Radar) transceiver for metal detection under the ground. Before using prototyped GPR for detecting the metal under the ground, several of calibration processes must be performed, namely phase calibration and monocycle pulse waveform calibration. After completing the calibrations, this prototyped GPR would be ready for detecting a hidden object such as a metal plate 5 cm under the ground in our small test range size 25 cm …

Simultaneous Treatment Of Organic (Phenol) And Heavy Metal (Cr6+ Or Pt4+) Wastes Over Tio2, Zno-Tio2 And Cds-Tio2 Photocatalysts, Slamet Slamet, R. Arbianti, Daryanto Daryanto

Makara Journal of Technology

Simultaneous Treatment of Organic (Phenol) and Heavy Metal (Cr6+ or Pt4+) Wastes over TiO2, ZnO-TiO2 and CdS-TiO2 Photocatalysts. Treatment of heavy metal (Cr6+ and Pt4+) and organic (phenol) wastes has been studied using the relatively new method, i.e. simultaneous photocatalytic process over TiO2 photocatalysts in the batch photoreactor. Following the photocatalytic reduction of the heavy metal wastes, recovery of Cr and Pt was carried out by precipitation and leaching method, respectively. The experimental results show that in the simultaneous photocatalytic system, there is a synergism effect between the photocatalytic reduction of heavy metal waste (Cr6+ or Pt4+) and the oxidation …

Design Of Generating Dual Frequency Operation For Triangular Microstrip Antenna Using Electromagnetic Coupling, Indra Surjati, Eko Tjipto Rahardjo, Djoko Hartanto

Makara Journal of Technology

Design of Generating Dual Frequency Operation for Triangular Microstrip Antenna Using Electromagnetic Coupling. A new design is proposed in this paper by applying a pair of slits using a microstrip feed line. Therefore the microstrip line feeding system is electromagnetically coupled to the patch. The antenna works at two different frequencies in the range from 2 GHz to 4 GHz (S band frequency). The results of the simulation shows that the dual frequency operation can be created when the slit width is 1 mm and the height of the slits ranges from 10 mm to 14 mm with inter slit …

Development Of Low Frequency Vibration Method Of Direct-Write Deposition Relevant To Layer Manufacturing Application, Susilo Adi Widyanto, Alva Edy Tontowi, Jamasri Jamasri, Heru Santosa Budi Rochardjo

Makara Journal of Technology

The research of deposition process is the first step in development process of multi materials selective laser sintering. The deposition process enables to settle multi materials powder in horizontal formation on one layer. In this research we use low frequency (70 - 200Hz) to vibrate a hopper nozzle in which powder is settled. The research method consists of two steps, the first step is to determine flow-ability parameters and the second is to join flow ability parameter with other parameters such that the line width can be controlled. The results show that the line width depends on uniformity of particle …

High Temperature Heat Exchanger Project: Quarterly Progress Report July 1, 2005 Through September 30, 2005, Anthony Hechanova

Publications (NSTD)

Quarterly Collaboration Meeting. The University of California, Berkeley, hosted a UNLVRF HTHX Project quarterly meeting on September 12. The purpose of the meeting was to promote collaboration and communication among the UNLV Research Foundation partners. Collaborators discussed their research program plan and provided an update on their progress. The next meeting will be in December in Las Vegas, NV hosted by UNLV.

A Fe-Fd Hybrid Scheme For Solving Parabolic Two-Step Micro Heat Transport Equations In Irregularly Shaped Three Dimensional Double -Layered Thin Films Exposed To Ultrashort -Pulse Lasers, Brian R. Barron

Doctoral Dissertations

Multi-layer thin films are important components in many micro-electronic devices. These films are often used when a single film layer is insufficient to meet devices specifications. The continued reduction in component size has the side effect of increasing the thermal stress on these films and consequently the devices they comprise. Understanding the transfer of heat-energy at the micro-scale is important for thermal processing using a pulse-laser. Often, micro-voids may be found in processed devices. This is due to thermal expansion. Such defects may cause an amplification of neighboring defects resulting in severe damage and consequently the failure of the device. …

Support For A Delivery Train Based Material Handling Mechanism, Sai P. Boyedapu

Electrical & Computer Engineering Theses & Dissertations

Modeling a delivery train system is more challenging than traditional forklift systems as the delivery train model consists of a tugger, cart and a controller that combine to deliver materials within a manufacturing plant. Also, the decision logic for selection of carts and tuggers, joining of loads to particular delivery trains is more complicated than forklift systems. Simulation software such as Arena, Automod and Flexsim do not provide direct support for modeling delivery train systems.

In this thesis, an object-oriented, platform and language independent model of a delivery train was designed. The model was then implemented as an extension to …

Validation Of Finite Element Beam Models, Pavan R. Madhineni

Mechanical & Aerospace Engineering Theses & Dissertations

Finite Element (FE) methods these days are becoming very popular to predict the responses of structures in industries, such as the aerospace and automobile industries. When there is a new design or modification of an existing design, the product must be tested to fulfill the criterion projected by the industry or external agencies before it can be launched. The product must be checked for each and every aspect, and every minute detail of each of the external forces. Hence, it becomes very important to carry out the model validation on the product.

This thesis describes validation of finite element (FE) …

Freeze-Form Extrusion Fabrication Of Ceramics, Tieshu Huang, Michael S. Mason, Greg Hilmas, Ming-Chuan Leu

Materials Science and Engineering Faculty Research & Creative Works

A novel, environmentally friendly solid freeform fabrication method called Freeze-form Extrusion Fabrication (FEF) has been developed for the fabrication of ceramic-based components. The method is based on deposition of ceramic pastes using water as the media. The ceramic solids loading can be 50 vol. % or higher and initial studies have focused on the use of aluminum oxide (Al₂O₃). The FEF system components and their interaction are examined, and the main process parameters affecting part geometry defined. 3-D shaped components have been fabricated by extrusion deposition of the ceramic paste in a layer-by-layer fashion. The feasibility …

Modeling, Fabrication, And Optimization Of Niobium Cavities Final Phase: Final Report, Robert A. Schill Jr., Mohamed Trabia, William Culbreth

Transmutation Sciences Materials (TRP)

This final report provides the activities and accomplishments of Modeling, Fabrication, and Optimization of Niobium Cavities – Final Phase. The fluid flow experiments for the etching of the superconducting cavity walls and baffle designs of phase II of the three phases has been completed leading to a MS thesis in December of 2003. Designing the experimental setup of secondary electron emission was well underway in early summer of 2003 when funding was made available for this portion of the study. By March 2004, many of the components of the experimental study reached UNLV with some assembly accomplished. The first secondary …

High Temperature Heat Exchanger Project: Quarterly Progress Report April 1, 2005 Through June 30, 2005, Anthony Hechanova

Publications (NSTD)

Quarterly Collaboration Meeting. General Atomics hosted a UNLVRF HTHX Project quarterly meeting on June 5 in San Diego, California. The purpose of the meeting was to promote collaboration and communication among the UNLV Research Foundation partners. Collaborators had the opportunity to discuss their research program plan and update their progress. The next meeting will be in September in Berkeley hosted by UC Berkeley.

HTHX Computational Design (UNLV). Work on optimizing the ceramic offset strip in compact HTHX design through parametric studies was performed and completed. A simple single channel model was used to perform parametric studies on dimensions and flow …

Method Of Reducing Internal Stress In Materials, Maher S. Amer, John F. Maguire

Mechanical and Materials Engineering Faculty Publications

Methods are provided for adjusting and controlling the stress between layers of material in a multilayer structure. A first stress is configured in a region of stress on the substrate material. A second material is then deposited over the substrate. A second stress results between the substrate and the second material such that a net stress results where the net stress is a function of said first and second stresses. As such, the first stress can be configured to achieve a predetermined, desired net stress. For example, the first stress can be configured to cancel out the second stress such …

Slip Behavior In Liquid Films On Surfaces Of Patterned Wettability: Comparison Between Continuum And Molecular Dynamics Simulations, Nikolai V. Priezjev, Anton A. Darhuber, Sandra M. Troian

Mechanical and Materials Engineering Faculty Publications

We investigate the behavior of the slip length in Newtonian liquids subject to planar shear bounded by substrates with mixed boundary conditions. The upper wall, consisting of a homogenous surface of finite or vanishing slip, moves at a constant speed parallel to a lower stationary wall, whose surface is patterned with an array of stripes representing alternating regions of no shear and finite or no slip. Velocity fields and effective slip lengths are computed both from molecular dynamics (MD) simulations and solution of the Stokes equation for flow configurations either parallel or perpendicular to the stripes. Excellent agreement between the …

Modeling, Fabrication, And Optimization Of Niobium Cavities: Phase Iii Fourth Quarterly Report, Robert A. Schill Jr., Mohamed Trabia, William Culbreth

Transmutation Sciences Materials (TRP)

Niobium cavities are important parts of the integrated NC/SC high-power linacs. Over the years, researchers in several countries have tested various cavity shapes. They concluded that elliptically shaped cells are the most appropriate shape for niobium superconducting cavities. The surface preparation can significantly affect the secondary electron emission yields. Such yields are used in design codes. Current codes use values obtained from niobium samples cleaned by a different means at temperatures other than the operating temperature. Secondary electron emission studies on LANL surface-cleaned niobium are conducted with preliminary data presented in this report at room temperature. Soon studies will be …

3d Modelling With Linear Approaches Using Geometric Primitives, Mochammad Zuliansyah

Makara Journal of Technology

In this paper, we study linear approaches for 3D model acquisition from non-calibrated images. First, the intrinsic and extrinsic camera calibration is taken into consideration. In particular, we study the use of a specific calibration primitive: the parallelepiped. Parallelepipeds are frequently present in man-made environments and naturally encode the affine structure of the scene. Any information about their euclidean structure (angles or ratios of edge lengths), possibly combined with information about camera parameters is useful to obtain the euclidean reconstruction. We propose an elegant formalism to incorporate such information, in which camera parameters are dual to parallelepiped parameters, i.e. any …

Tensile Properties Of Martensitic Stainless Steels At Elevated Temperatures, Ajit K. Roy, Srinivasarao R. Kukatla, Bhagath Yarlagadda, V. N. Potluri, Martin Lewis, Brendan O'Toole

Mechanical Engineering Faculty Research

Tensile properties of quenched and tempered martensitic alloys EP-823, HT-9, and 422 were evaluated at temperatures ranging from ambient to 600 °C as a function of three different tempering times. The results indicated that the yield strength, ultimate tensile strength, and the failure strength were gradually reduced with increasing temperature. The ductility parameters were enhanced at elevated temperatures due to increased plastic flow. However, the tempering time did not significantly influence these properties. The evaluation of the fracture surfaces by scanning electron microscopy revealed reduced cracking and dimpled microstructures, indicating enhanced ductility at higher testing temperatures.

Residual Stress Characterization In Structural Materials By Destructive And Nondestructive Techniques, Ajit K. Roy, Anand Venkatesh, Vikram Marthandam, Satish Dronavalli, Douglas P. Wells, Ronald Rogge

Mechanical Engineering Faculty Research

Transmutation of nuclear waste is currently being considered to transform long-lived isotopes to species with relatively short half-lives and reduced radioactivity through capture and decay of minor actinides and fission products. This process is intended for geologic disposal of spent nuclear fuels for shorter durations in the proposed Yucca Mountain repository. The molten lead-bismuth-eutectic will be used as a target and coolant during transmutation, which will be contained in a subsystem vessel made from materials such as austenitic (304L) and martensitic (EP-823 and HT-9) stainless steels. The structural materials used in this vessel will be subjected to welding operations and …