Materials Science and Engineering Commons^™

Lunalight Project: Solar-Rechargeable Led Lantern And Cell Phone Charger, Sean C. Dawson, Michael E. Deagen, Francisco N. Dye, Brian S. Mircheff, Ryan O. Ramelb

Materials Engineering

Today, 1.6 billion people in the world do not have access to grid electricity. Villagers living off the grid in developing nations resort to kerosene lanterns to light their homes. The fumes from burning kerosene are toxic and lead to respiratory illnesses over time. Our sponsor, OneMillionLights, plans to help people to escape poverty by providing them with a clean source of light at night. Children that must work in the fields during the day can use a solar-rechargeable lantern at night to read or study, and street vendors can use the lanterns at night to improve their businesses.

The …

The Design And Fabrication Of A Microfluidic Reactor For Synthesis Of Cadmium Selenide Quantum Dots Using Silicon And Glass Substrates, Peter Robert Gonsalves

Master's Theses

A microfluidic reactor for synthesizing cadmium selenide (CdSe) quantum dots (QDs) was synthesized out of a silicon wafer and Pyrex glass. Microfabrication techniques were used to etch channels into the silicon wafer. Holes were wet-drilled into the Pyrex glass using a diamond-tip drill bit. The Pyrex wafer was anodically bonded to the etched silicon wafer to enclose the microfluidic reactor. Conditions for anodic bonding were created by exposing the stacked substrates to 300V at ~350oC under 5.46N of force. A syringe containing a room temperature CdSe solution was interfaced to the microfluidic reactor by using Poly (dimethylsiloxane) (PDMS) as an …

Evaluating Superconducting Ybco Film Properties Using Xray Photoelectron Spectroscopy, Paul N. Barnes, Justin C. Tolliver, Timothy J. Haugan, Sharmila M. Mukhopadhyay, John T. Grant

Mechanical and Materials Engineering Faculty Publications

Initial results have been recently reported that suggest a potential correlation exists between the full-width-halfmaximum (FWHM) of the Y(3d) peak obtained by x-ray photoelectron spectroscopy (XPS) and the critical current density a YBa₂Cu₃O₇-x film can carry. In particular, the Y(3d_5/2) demonstrated a stronger correlation. Transport currents were determined by the 4-point contact method using the 1μV/cm criterion. An apparent correlation was also suggested between the Y(3d) FWHM and ac loss data points were acquired to further test the usefulness of the correlations. Samples were created by pulsed laser deposition of YBa_{2 …}

Controlling Nanoparticles Formation In Molten Metallic Bilayers By Pulsed-Laser Interference Heating, Mikhail Khenner, Sagar Yadavali, Ramki Kalyanaraman

Mathematics Faculty Publications

The impacts of the two-beam interference heating on the number of core-shell and embedded nanoparticles and on nanostructure coarsening are studied numerically based on the non-linear dynamical model for dewetting of the pulsed-laser irradiated, thin (< 20 nm) metallic bilayers. The model incorporates thermocapillary forces and disjoining pressures, and assumes dewetting from the optically transparent substrate atop of the reflective support layer, which results in the complicated dependence of light reflectivity and absorption on the thicknesses of the layers. Stabilizing thermocapillary effect is due to the local thickness-dependent, steady- state temperature profile in the liquid, which is derived based on the mean substrate temperature estimated from the elaborate thermal model of transient heating and melting/freezing. Linear stability analysis of the model equations set for Ag/Co bilayer predicts the dewetting length scales in the qualitative agreement with experiment.

Dechlorination Of Environmental Contaminants Using A Hybrid Nanocatalyst: Palladium Nanoparticles Supported On Hierarchical Carbon Nanostructures, Hema Vijwani, Abinash Agrawal, Sharmila M. Mukhopadhyay

Mechanical and Materials Engineering Faculty Publications

This paper demonstrates the effectiveness of a new type of hybrid nanocatalyst material that combines the high surface area of nanoparticles and nanotubes with the structural robustness and ease of handling larger supports. The hybrid material is made by fabricating palladium nanoparticles on two types of carbon supports: as-received microcellular foam (Foam) and foam with carbon nanotubes anchored on the pore walls (CNT/Foam). Catalytic reductive dechlorination of carbon tetrachloride with these materials has been investigated using gas chromatography. It is seen that while both palladium-functionalized carbon supports are highly effective in the degradation of carbon tetrachloride, the rate of degradation …

Development And Validation Of Probabilistic Fatigue Models Containing Out-Life Suspensions, Noel S. Murray

College of Graduate Studies: Theses & Dissertations

Author's abstract: In the area of reliability engineering it is necessary to be confident that a component or system of components will not fail under use for safety and cost reasons. One major mechanism of failure to a mechanical component is fatigue. This is the repetitious motion of loading and unloading of the material, typically below the ultimate tensile strength of the material, which ultimately leads to a catastrophic failure. To ensure this does not happen, engineers design components based on tests to determine the life of these components. These tests are typically conducted on a bench type tester in …

Numerical Simulation Of Natural Convection In Rectangular Enclosures Of Varying Aspect Ratios And Its Feasibility In Environmental Impact Management Studies, Charles R. Walker

College of Graduate Studies: Theses & Dissertations

Author's abstract: Numerical simulation was used to investigate natural convection in horizontal and vertical enclosures with and without an internal heat source. Natural convection in rectangular enclosures is found in many real-world applications. Included in these applications are the energy efficient design of buildings, operation and safety of nuclear reactors, solar collector design, passive energy storage, heat transfer across multi-pane windows, thermo-electric refrigeration and heating devices, and the design-for-mitigation of optical distortion in large-scale laser systems. Considering all these applications, especially controlling heat transfer in nuclear power plants, knowledge and research results of natural convection in enclosure play a vital …

A Front Tracking Model Of The Maxus-8 Microgravity Solidification Experiment On A Ti-45.5at.% Al-8at.%Nb Alloy, Robin Mooney, Shaun Mcfadden, Marek Rebow, David J. Browne

Articles

On 26th March 2010 the MAXUS-8 sounding rocket was launched from the Esrange Space Center in Sweden. As part of the Intermetallic Materials Processing in Relation to Earth and Space Solidification (IMPRESS) project, a solidification experiment was conducted on a Ti-45.5at.%Al-8at.%Nb intermetallic alloy in a module on this rocket. The experiment was designed to investigate columnar and equiaxed microstructures in the alloy. A furnace model of the MAXUS 8 experiment with a Front Tracking Model of solidification has been developed to determine the macrostructure and thermal history of the samples in the experiment. This paper gives details of results of …

Introducing Fly Ash Into Lsi's Recipe, Andrew Mathias Beckrich

All Graduate Theses, Dissertations, and Other Capstone Projects

There has been published data that states that concrete producers can use Fly Ash as an alternative to Portland cement and still generate similar or better strength properties. By applying these principles to our industry and products, what new processes will need to be put in place and followed? What is the correct combination/portion of Fly Ash that will produce similar and better results as well as the adjusted new recipes? What type of cost is associated with the introduction of this new ingredient? Lastly, how does this affect the quality and reputation of the product?

Cryogenic Machining And Burnishing Of Az31b Magnesium Alloy For Enhanced Surface Integrity And Functional Performance, Zhengwen Pu

Theses and Dissertations--Mechanical and Aerospace Engineering

Surface integrity of manufactured components has a critical impact on their functional performance. Magnesium alloys are lightweight materials used in the transportation industry and are also emerging as a potential material for biodegradable medical implants. However, the unsatisfactory corrosion performance of Mg alloys limits their application to a great extent. Surface integrity factors, such as grain size, crystallographic orientation and residual stress, have been proved to remarkably influence the functional performance of magnesium alloys, including corrosion resistance, wear resistance and fatigue life.

In this dissertation, the influence of machining conditions, including dry and cryogenic cooling (liquid nitrogen was sprayed to …

Technical Feasibility Of Storage On Large Dish Stirling Systems, Charles E. Andraka, K Scott Rawlinson, Nathan P. Siegel

Faculty Journal Articles

Dish-Stirling systems have been demonstrated to provide high-efficiency solar-only electrical generation, holding the world record at 31.25%. This high efficiency results in a system with a high possibility of meeting the DOE SunShot goal of $0.06/kWh. Current dish-Stirling systems do not incorporate thermal storage. For the next generation of non-intermittent and cost-competitive solar power plants, we propose a thermal energy storage system that combines latent (phase-change) energy transport and latent energy storage in order to match the isothermal input requirements of Stirling engines while also maximizing the exergetic efficiency of the entire system. This report takes an initial look at …

Development Of A Multi-Material, Multi-Technology Fdm System For Process Improvement Experimentation, David Espalin

Open Access Theses & Dissertations

Over the last three decades, developments within the area of Additive Manufacturing (AM) have resulted in novel technologies capable of producing highly customized, complex part geometries in a fraction of the lead time required by traditional manufacturing methods (e.g., injection molding, metal casting). In particular, fused deposition modeling (FDM), a material extrusion AM process, can produce parts using production-grade thermoplastics like acrylonitrile butadiene styrene, polycarbonate, and polyetherimide. Additionally, non-commercial materials (e.g., polycaprolactone, ceramic loaded polymers, carbon nanotube loaded polymers) have been processed using FDM in part to demonstrate the potential diversity in material selection.

Recently, a myriad of personal 3D …

Oxidation Of Borides And Carbides With Y2o3 And Ta Additions, Salvador Manuel Rodriguez

Open Access Theses & Dissertations

The study presented here describes an investigation of an oxidation scale of a fully-sintered Y2O3-ZrB2-TiC composite exposed in air at 1173K. Upon oxidation of the boride/carbide, a ZrO2-TiO2 was expected to form similar to the ZrO2-SiO2 dual scale of an oxidized ZrB2-SiC. The 47wt% Y2O3-38wt%ZrB2-16wt%TiC composite formed a dual scale consisting primarily of an Y2O3-ZrO2-TiC inner scale with an outer scale of ZrO2-TiO2-Y2O3.

The samples oxidized with a parabolic layer growth allowing the calculation of the effective diffusion coefficient indicating that the oxidation was controlled by oxygen ingress through primarily the ZrO2-Y2O3 phase. The oxygen potential between the inner layer …

Finite Element Analysis Of The Contact Deformation Of Piezoelectric Materials, Ming Liu

Theses and Dissertations--Chemical and Materials Engineering

Piezoelectric materials in the forms of both bulk and thin-film have been widely used as actuators and sensors due to their electromechanical coupling. The characterization of piezoelectric materials plays an important role in determining device performance and reliability. Instrumented indentation is a promising method for probing mechanical as well as electrical properties of piezoelectric materials.

The use of instrumented indentation to characterize the properties of piezoelectric materials requires analytical relations. Finite element methods are used to analyze the indentation of piezoelectric materials under different mechanical and electrical boundary conditions.

For indentation of a piezoelectric half space, a three-dimensional finite element …

Investigation Into The Usability Of Micromechanical Models To Predict The Behavior Of A Nanocomposite Polymer, Jason Handlogten

All Graduate Theses, Dissertations, and Other Capstone Projects

The purpose of this thesis was to determine the acceptability of a set of existing nanocomposite test specimens for tensile testing and then to determine the Young's and shear modulus of these test specimens. If the test specimens were found to be acceptable, the accuracy of three micromechanical models was to be evaluated by comparing their predictions to the mechanical properties determined from testing the specimens. The set of existing nanocomposite test specimens had a distinct concave shape on two surfaces that were believed to be intended as flat. In order to determine if they adhered to the Type I …

Chemical Mechanical Planarization Of Electronic Materials, Fnu Atiquzzaman

USF Tampa Graduate Theses and Dissertations

In the modern semiconductor manufacturing processes, chemical mechanical planarization (CMP) has attained important processing step because of its ability to provide global planarization. CMP is the planarization technique which is used for the removal of excess material, as left over from the previous processing steps. In addition, CMP offers a uniform surface that is essential for subsequent processing steps, especially for the high resolution photolithography processes. In simpler notation, CMP is a process where a chemical reaction enhances in obtaining a planar surface through removal of the mechanical materials from a wafer.

In this study, CMP performance of three electronic …

Formation Of Organized Nanostructures From Unstable Bilayers Of Thin Metallic Liquids, Mikhail Khenner, Sagar Yadavali, Ramki Kalyanaraman

Mathematics Faculty Publications

Dewetting of pulsed-laser irradiated, thin (< 20 nm), optically reflective metallic bilayers on an optically transparent substrate with a reflective support layer is studied within the lubrication equations model. A steady-state bilayer film thickness (h) dependent temperature profile is derived based on the mean substrate temperature estimated from the elaborate thermal model of transient heating and melting/freezing. Large thermocapillary forces are observed along the plane of the liquid-liquid and liquid-gas interfaces due to this h-dependent temperature, which, in turn, is strongly influenced by the h-dependent laser light reflection and absorption. Consequently the dewetting is a result of the competition between thermocapillary and intermolecular forces. A linear analysis of the dewetting length scales established that the non-isothermal calculations better predict the experimental results as compared to the isothermal case within the bounding Hamaker coefficients. Subsequently, a computational non-linear dynamics study of the dewetting pathway was performed for Ag/Co and Co/Ag bilayer systems to predict the morphology evolution. We found that the systems evolve towards formation of different morphologies, including core-shell, embedded, or stacked nanostructure morphologies.

Effect Of Extracellular Matrix (Ecm) Protein Micropatterns On The Behavior Of Human Neuroblastoma Cells, Ishwari Poudel

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Recent advances in patterning techniques and emerging surface microtechnologies have allowed cell micropatterning to control spatial location of the cells on a surface as well as cell shape, attachment area, and number of contacting neighbor cells. These parameters play important roles in cell cellular behaviors. Cell micropatterning has thus become one of the most important strategies for biomedical applications, such as, tissue engineering, diagnostic immunoassays, lab-on-chip devices, bio-sensing, etc., and cell biology studies as well. For neuronal cells, there have been attempts to distribute neuronal cells on specific patterns to control cell-to-cell interaction. However, there have been very limited understanding …

Surface Wetting And Friction Studies Of Nano-Engineered Surfaces On Copper Substrate, Julius Sheldon Morehead

Graduate Theses and Dissertations

Nano-engineered-textures on a material surface can dramatically improve the wetting and non-wetting properties of a surface, and they also show promise to address friction issues that affect surfaces in contact. In this work, aluminum-induced crystallization (AIC) of amorphous silicon (a-Si) was used to produce nano-textures on copper (Cu) substrates. A study was performed to examine the effects of changing the annealing conditions and a-Si thickness on nano-texture formation. The creation of various nano-topographies and chemically modifying them using octafluorocyclobutane (C4F8) was performed to control hydrophilicity, hydrophobicity, and oil affinity of nano-textured surfaces. A video-based contact angle measurement system was used …

Strength Of Polycrystalline Ceramics Under Shock Compression, Jianbin Zhu

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Determinations of Some polycrystalline ceramics’ strength properties and inelastic deformation mechanisms in the shocked state are critically important to the design and optimization of armor structures involving these materials. In this work, multiscale modeling and simulations have been carried out to study strength of the effects of polycrystalline microstructure, crystal anisotropy, porosity, and their interactions with microscopic deformation/damage mechanisms on the responses of several polycrystalline ceramics under shock compression and to extract their shock strengths from the wave profiles measured in the related plate impact shock wave experiments.

With a mesoscopic computational model, the roles of intragranular microplasticity and deformation …

Modeling And Control Of A Flexible Ionic Polymer Metal Composite(Ipmc) Actuator For Underwater Propulsion, Shivakanth Gutta

UNLV Theses, Dissertations, Professional Papers, and Capstones

The goal of this research is to model and control the underwater vehicle propelled by IPMC actuator. IPMC consists of an ionic membrane sandwiched between two metallic electrodes. When an external voltage is applied, IPMC undergoes large deformation due to transport of ions. Due to its ability to work in aqueous environments, it can be used for developing small scale underwater vehicles.

First, Finite element approach is used to describe the dynamics of the both single and segmented IPMC actuator. In the approach presented, each element is attached with a local coordinate system that undergoes rigid body motion along with …

Modeling Of A Novel Solar Down Beam Test Facility Utilizing Newtonian Optics, Ryan J. Hoffmann

UNLV Theses, Dissertations, Professional Papers, and Capstones

As advances in concentrated solar energy progress there will inevitably be an increase in the demand of resources for testing new conceptions. Currently, there are limited facilities available for taking concentrated solar energy concepts from the laboratory bench scale to the engineering test scale. A proposed solution is a scientific and developmental facility that provides highly concentrated solar energy at ground level. The design presented is a solar down beam test facility utilizing a Newtonian optics approach with a flat rectangular down beam mirror to reflect and concentrate the sun's rays at ground level.

Literature review suggests a hyperbolic reflector …

Molecular Diffusion And Slip Boundary Conditions At Smooth Surfaces With Periodic And Random Nanoscale Textures, Nikolai V. Priezjev

Mechanical and Materials Engineering Faculty Publications

The influence of periodic and random surface textures on the flow structure and effective slip length in Newtonian fluids is investigated by molecular dynamics (MD) simulations. We consider a situation where the typical pattern size is smaller than the channel height and the local boundary conditions at wetting and nonwetting regions are characterized by finite slip lengths. In case of anisotropic patterns, transverse flow profiles are reported for flows over alternating stripes of different wettability when the shear flow direction is misaligned with respect to the stripe orientation. The angular dependence of the effective slip length obtained from MD simulations …

Flexible Connection Elastomeric Rubber As A Pounding Resisting Element Between Two Adjacent Buildings, Yuskar Lase, James Jatmiko Oetomo

Makara Journal of Technology

Flexible Connection Elastomeric Rubber as a Pounding Resisting Element between Two Adjacent Buildings To solve pounding problem of two adjacent buildings, structural designer usually employs a dilatation between the structures or make the two structures as a monolith structure. Other alternative is by using an elastomeric rubber as a pounding resisting element between the two structures. Effectiveness in applying elastomeric rubber component as flexible connection of two adjacent structures is the main focus of this paper. Various simulations such as structure models, earthquake excitations and openings in gap element are studied. Observation of maximum structural responses will be performed for …

Improvement Of High Temperature Oxidation Of Low Carbon Steel Exposed To Ethanol Combustion Product At 700 °C By Hot-Dip Aluminizing Coating, Mohammad Badaruddin

Makara Journal of Technology

Low carbon steel (AISI 1005) was coated by hot-dipping into a molten Al-10% Si bath at 700 °C for 18s. After hotdipping treatment, the coating layers consisted of Al, Si, FeAl3, τ5-Fe2Al8Si, and Fe2Al5. The bare steel and the aluminized steel were isothermally oxidized at 700 °C in ethanol combustion product at atmospheric pressure for 49 h. The aluminized steel shows good performance in high temperature oxidation because the formation of Al2O3 layer on the coating surface. The growth of iron oxide nodules on the surface coating was accelerated by rapid outward diffusion of Fe-ions due to the presence of …

Effect Of Copper Addition On Mechanical Properties And Electrical Conductivity Of Pp/C-Cu Bipolar Plate Composites, Anne Zulfia, Taufik Abimanyu, Verina Warga Dalam

Makara Journal of Technology

Effect of Copper Addition on Mechanical Properties and Electrical Conductivity of PP/C-Cu Bipolar Plate Composites. Bipolar plate is a major component in PEM fuel cell which possess main function of collecting and removing electrons from anode to cathode. Therefore, materials for bipolar plates produced must have high electrical conductivity. To obtain bipolar plate materials which is cheap, lightweight and high conductivity, so it is developed bipolar plates material based on PP/C-Cu composite. PP/C-Cu composites has been made by mixing all materials then compounding, rheomix, hot blending and hot press. Cu (Copper) has been used various from 0.1 wt%, 1 wt% …

Application Of Principal Component Proximity Transform And Geostatistics Methods For Volume Shale Distribution As Reservoir Characreristic Imaging In Seismic 3d, Nur Islami

Makara Journal of Technology

Application of Principal Component Proximity Transform and Geostatistics Methods for Volume Shale Distribution as Reservoir Characreristic Imaging in Seismic 3D. Principal component proximity transform (PCPT) technique was used to predict the content of volume shale into seismic data in reservoir modeling framework. The goal in this research is to get the volume shale imaging in three dimensions and allow for reservoir modelling. The reservoir modelling requires an integrated quantitative and qualitative data sources collected separately, such as well and seismic data. Integrating PCPT and Geostatistic methods can generate the detail information for characterization of reservoir’s properties. Finally, it shows that …

Application Of Empirical Orthogonal Function Models To Analyze Shoreline Change At Bangkalan Madura, Darius Arkwright, Suntoyo Suntoyo

Makara Journal of Technology

Bangkalan’s shoreline, especially on the opposite side of Surabaya, has been evaluated to determine the morphological changes due to wave attack, near-shore current, long-shore sediment transport and coastal configuration. This research aims to determine the dominant patterns of variation of Bangkalan’s shoreline change, expressed by Eigen-function in empirical orthogonal function (EOF) models. That was started with data collection such as oceanographic data (wave and tidal), bathymetry and topographic map and sediment data. All data was used for forecasting two-monthly shoreline. Coordinate of two-monthly shoreline was used as input of EOF model. The first Eigen mode is a profile of shoreline …

Establishment Code Hand Palm (Palm Code) 2d Gabor-Based Method, I Ketut Gede Darma Putra, Wira Bhuana, Erdiawan Erdiawan

Makara Journal of Technology

Establishment Code Hand Palm (Palm Code) 2D Gabor-Based Method. Palmprint is relatively new in physiological biometrics. Palmprint ROI segmentation and feature extraction are two important issues in palm print recognition. This paper introduces two steps in the center of mass moment method for ROI segmentation that will be applied in the Gabor 2D filter to obtain palm code as palmprint feature vector. Normalized Hamming distance was used to measure the similarity degrees of two feature vectors of palmprint. The system was tested using database 1000 palmprint images generated from 5 samples from each of the 200 persons randomly selected with …

The Effectiveness Of Anaerobic Baffled Reactor And Rotating Biological Contactor In Batik Wastewater Treatment, Augustinus Ignatius Kristijanto, Widhi Handayani, Purwanti Asih Anna Levi

Makara Journal of Technology

Batik is one of popular arts of Indonesia. The batik industries in Sragen, Central Java, are prepared to compete in global market. In order to realize that objective, batik products should fulfill some qualifications, one of which is “environmental friendliness”. As batik production is usually generating wastewater which pollutes the environment, the technology of wastewater treatment should be developed to solve the problem. This preliminary study has been done to assess the effectiveness of anaerobic baffled reactor (ABR) and rotating biological contactor (RBC) in batik wastewater treatment. In 40 days of treatment period, the ABR performance in reducing pollutants showed …