Power and Energy Commons^™

Electric Aircraft System Co-Simulation Including Body, Propeller, Propulsion, And Energy Storage Models, Damien Lawhorn, Vandana Rallabandi, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

This paper discusses the multi physics modeling of an electric aircraft with distributed electric propulsion. Mathematical models for the aircraft body, propellers, propulsive motors, power electronics inverters, and batteries are developed. Two types of models are proposed for the power electronics inverters and electric machines, namely, average models which allow study of the aircraft performance under a specified mission profile, and detailed switching models used for transient examination. A new simulation framework was developed to allow communication between these two types of models so that losses and thermal stresses in the power electronics converters can be estimated especially during takeoff, …

Anonymous And Efficient Message Authentication Scheme For Smart Grid, Libing Wu, Jing Wang, Sherali Zeadally, Debiao He

Information Science Faculty Publications

Smart grid has emerged as the next-generation electricity grid with power flow optimization and high power quality. Smart grid technologies have attracted the attention of industry and academia in the last few years. However, the tradeoff between security and efficiency remains a challenge in the practical deployment of the smart grid. Most recently, Li et al. proposed a lightweight message authentication scheme with user anonymity and claimed that their scheme is provably secure. But we found that their scheme fails to achieve mutual authentication and mitigate some typical attacks (e.g., impersonation attack, denial of service attack) in the smart grid …

Design Optimization Of Electric Machines With 3d Fea And A New Hybrid Doe-De Numerical Algorithm, Narges Taran, Vandana Rallabandi, Dan M. Ionel, Greg Heins, Dean Patterson, Ping Zhou

Power and Energy Institute of Kentucky Faculty Publications

This paper discusses the multi-objective optimization of axial flux permanent magnet (AFPM) machines with ferrite spoke-type magnets, utilizing 3D finite element models. Three-dimensional finite element analysis is computationally expensive, and furthermore, substantial computation time is expended by optimization algorithms in evaluating low performing designs whose performance is far from the optimum if the search space is not specified correctly. In this regard, this work proposes two new methods for identifying the search space. The search is limited to ranges of input geometric variables where high performing designs are likely to be found. The optimization algorithm utilized is based on surrogate …

Inductance Testing For Ipm Synchronous Machines According To The New Ieee Std 1812 And Typical Laboratory Practices, Vandana Rallabandi, Narges Taran, Dan M. Ionel, Ping Zhou

Power and Energy Institute of Kentucky Faculty Publications

Equivalent circuit parameters serve as the basis for performance estimation and implementation of power electronic drives controls and therefore their accurate evaluation is very important. Specified in the newly approved IEEE Std 1812, a short-circuit test can be employed, in combination with an open-circuit measurement, in order to determine the back emf and the synchronous inductance. In the case of interior permanent magnet (IPM) machines, this approach can be used only to determine the d-axis inductance and additional and separate measurements are required for the q-axis inductance. In this respect, various methods, inclusive of dc step response tests, on-load tests, …

A Comparative Study Of Methods For Calculating Ac Winding Losses In Permanent Magnet Machines, Narges Taran, Vandana Rallabandi, Dan M. Ionel, Greg Heins, Dean Patterson

Power and Energy Institute of Kentucky Faculty Publications

In this study different methods of estimating the additional ac winding loss due to eddy currents at open-circuit are explored. A comparative study of 2D and 3D FEA, and hybrid numerical and analytical methods is performed in order to recommend feasible approaches to be employed. Axial flux permanent magnet (AFPM) machine case studies are included, namely a machine with open slots and a coreless configuration. These machine topologies are expected to present a substantial amount of ac winding loss, which would therefore need to be considered during optimal design. This study is one of the first ones to compare meticulous …

A Systematic Study On The Effects Of Dimensional And Materials Tolerances On Permanent Magnet Synchronous Machines Based On The Ieee Std 1812, Narges Taran, Vandana Rallabandi, Dan M. Ionel, Ping Zhou, Mark Theile, Greg Heins

Power and Energy Institute of Kentucky Faculty Publications

In the process of designing and manufacturing an electrical machine, a systematic study of dimensional and material tolerances is of the utmost importance. This paper proposes a systematic method by which the effect of design specification variations on permanent magnet (PM) synchronous machine performance may be identified and quantified. The method combines design of experiments techniques, open-circuit and short-circuit physical measurements, and virtual test simulations conducted based on the recently approved IEEE Std 1812 testing guide. Three case studies, two provided by a spoke-type PM radial field machine configuration, in two designs with different electromagnetic loading, and an axial flux …

Incorporating Battery Energy Storage Systems Into Multi-Mw Grid Connected Pv Systems, Vandana Rallabandi, Oluwaseun M. Akeyo, Nicholas Jewell, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

This paper analyzes the configuration, design, and operation of multi-MW grid connected solar photovoltaic (PV) systems with practical test cases provided by a 10-MW field development. In order to improve the capacity factor, the PV system operates at its maximum power point during periods of lower irradiance, and the power output is limited to a rated value at high irradiance. The proposed configuration also incorporates a utility scale battery energy storage system (BESS) connected to the grid through an independent inverter and benefits of the experience gained with a 1-MW 2-MWh BESS large demonstrator. The BESS power smoothing and frequency …

Study Of Factors Affecting Distribution System Pv Hosting Capacity, Fanxun Li

Theses and Dissertations--Electrical and Computer Engineering

As renewable energy plays an increasingly important role in the power system, the addition of PV systems to the distribution network has become a major trend in the current power system development. However, if a PV system with excessive capacity is added to the distribution network, voltage problems may occur in the system. Hence, it is important to determine the capacity of the PV system that can be added at the distribution system.

The thesis aims to identify the major factors that affect the PV hosting capacity of distribution systems. The thesis studies various scenarios for the IEEE-123 test network …

Mathematical Programming Approach For The Design Of Satellite Power Systems, Allen Flath Iii

Theses and Dissertations--Electrical and Computer Engineering

Satellite power systems can be understood as islanded dc microgrids supplied by specialized and coordinated solar cell arrays augmented by electrochemical battery systems to handle high-power loads and periods of eclipse. The periodic availability of power, the limited capacity of batteries, and the dependence of all mission service on power consumption create a unique situation in which temporal power and energy scarcity exist. A multi-period model of an orbital satellite power system’s performance over a mission’s duration can be constructed. A modular power system architecture is used to characterize the system’s constraints. Using mathematical programming, an optimization problem can be …

Estimation Of Transmission Line Parameters Using Linear Method With Synchronized And Unsynchronized Data, Mustafa Lahmar

Theses and Dissertations--Electrical and Computer Engineering

Accurate value of transmission line parameters is important for power system protection applications, especially for distance relays whose zone settings are based on positive sequence line impedance. The research is devoted to estimating transmission line positive-sequence parameters from synchronized or unsynchronized measurements of voltage and current phasors that are obtained at both terminals of the line. The positive sequence parameters including series impedance and shunt admittance can be linearly estimated. The linear least square algorithm has been derived in this dissertation for different transmission line configurations. The algorithm is able to handle both synchronized and unsynchronized measurements and deal with …

Optimal Distribution Feeder Reconfiguration With Distributed Generation Using Intelligent Techniques, Ahmad Ghaweta

Theses and Dissertations--Electrical and Computer Engineering

Feeder reconfiguration is performed by changing the open/close status of two types of switches: normally open tie switches and normally closed sectionalizing switches. A whole feeder or part of a feeder may be served from another feeder by closing a tie switch linking the two while an appropriate sectionalizing switch must be opened to maintain the radial structure of the system. Feeder reconfiguration is mainly aiming to reduce the system overall power losses and improve voltage profile. In this dissertation, several approaches have been proposed to reconfigure the radial distribution networks including the potential impact of integrating Distributed Energy Resources …

Curricular Optimization: Solving For The Optimal Student Success Pathway, William G. Thompson-Arjona

Theses and Dissertations--Electrical and Computer Engineering

Considering the significant investment of higher education made by students and their families, graduating in a timely manner is of the utmost importance. Delay attributed to drop out or the retaking of a course adds cost and negatively affects a student’s academic progression. Considering this, it becomes paramount for institutions to focus on student success in relation to term scheduling.

Often overlooked, complexity of a course schedule may be one of the most important factors in whether or not a student successfully completes his or her degree. More often than not students entering an institution as a first time full …

Advanced Fault Area Identification And Fault Location For Transmission And Distribution Systems, Wen Fan

Theses and Dissertations--Electrical and Computer Engineering

Fault location reveals the exact information needed for utility crews to timely and promptly perform maintenance and system restoration. Therefore, accurate fault location is a key function in reducing outage time and enhancing power system reliability.

Modern power systems are witnessing a trend of integrating more distributed generations (DG) into the grid. DG power outputs may be intermittent and can no longer be treated as constants in fault location method development. DG modeling is also difficult for fault location purpose. Moreover, most existing fault location methods are not applicable to simultaneous faults. To solve the challenges, this dissertation proposes three …

Fault Location Techniques Using The Traveling Wave Method And The Discrete Wavelet Transform, Wesley Fluty

Theses and Dissertations--Electrical and Computer Engineering

Fault location within electric power systems is an important topic that helps reduce outage duration and increases reliability of the system. This paper explores the topic of fault location using traveling waves generated by fault conditions and the discrete wavelet transform used for time-frequency analysis. The single-ended and double-ended traveling wave methods are presented and evaluated on a single circuit and double circuit 500kV system modeled using MATLAB SIMULINK. Results are compared on the basis of wavelet used for analysis, sampling rate, and fault resistance.

Optimum Design Of Axial Flux Pm Machines Based On Electromagnetic 3d Fea, Narges Taran

Theses and Dissertations--Electrical and Computer Engineering

Axial flux permanent magnet (AFPM) machines have recently attracted significant attention due to several reasons, such as their specific form factor, potentially higher torque density and lower losses, feasibility of increasing the number of poles, and facilitating innovative machine structures for emerging applications. One such machine design, which has promising, high efficiency particularly at higher speeds, is of the coreless AFPM type and has been studied in the dissertation together with more conventional AFPM topologies that employ a ferromagnetic core.

A challenge in designing coreless AFPM machines is estimating the eddy current losses. This work proposes a new hybrid analytical …

Linking Lignin Source With Structural And Electrochemical Properties Of Lignin-Derived Carbon Materials, Wenqi Li, Yan Zhang, Lalitendu Das, Yikai Wang, Mi Li, Namal Wanninayake, Yunqiao Pu, Doo Young Kim, Yang-Tse Cheng, Arthur J. Ragauskas, Jian Shi

Biosystems and Agricultural Engineering Faculty Publications

Valorization of lignin to high-value chemicals and products along with biofuel production is generally acknowledged as a technology platform that could significantly improve the economic viability of biorefinery operations. With a growing demand for electrical energy storage materials, lignin-derived activated carbon (AC) materials have received increasing attention in recent years. However, there is an apparent gap in our understanding of the impact of the lignin precursors (i.e., lignin structure, composition and inter-unit linkages) on the structural and electrochemical properties of the derived ACs. In the present study, lignin-derived ACs were prepared under identical conditions from two different lignin …

Cfd Modeling On Hydrodynamic Characteristics Of Multiphase Counter-Current Flow In A Structured Packed Bed For Post-Combustion Co2 Capture, Li Yang, Fang Liu, Kozo Saito, Kunlei Liu

Mechanical Engineering Faculty Publications

Solvent-based post combustion CO₂ capture is a promising technology for industrial application. Gas-liquid interfaces and interactions in the packed bed are considered one of the key factors affecting the overall CO₂ absorption rate. Understanding the hydrodynamic characterizations within packed beds is essential to identify the appropriate enhanced mass transfer technique. However, multiphase counter-current flows in the structured packing typically used in these processes are complicated to visualize and optimize experimentally. In this paper, we aim to develop a comprehensive 3D multiphase, counter-current flow model to study the liquid/gas behavior on the surface of structured packing. The output from …

Two-Level Surrogate-Assisted Differential Evolution Multi-Objective Optimization Of Electric Machines Using 3-D Fea, Narges Taran, Dan M. Ionel, David G. Dorrell

Power and Energy Institute of Kentucky Faculty Publications

A two-level surrogate-assisted optimization algorithm is proposed for electric machine design using 3-D finite-element analysis (FEA). The algorithm achieves the optima with much fewer FEA evaluations than conventional methods. It is composed of interior and exterior levels. The exploration is performed mainly in the interior level, which evaluates hundreds of designs employing affordable kriging models. Then, the most promising designs are evaluated in the exterior loop with expensive 3-D FEA models. The sample pool is constructed in a self-adjustable and dynamic way. A hybrid stopping criterion is used to avoid unnecessary expensive function evaluations.

Optimal Design Of A Switched Reluctance Motor With Magnetically Disconnected Rotor Modules Using A Design Of Experiments Differential Evolution Fea-Based Method, Vandana Rallabandi, Jie Wu, Ping Zhou, David G. Dorrell, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

Switched reluctance (SR) machines are attractive because they present relatively high efficiency and torque density in spite of lacking permanent magnets. This paper focuses on a two-objective optimization of an external rotor SR motor with a stator that has concentrated coils and a rotor with magnetically isolated modules. The objectives are minimum loss and mass, and 11 independent dimensionless geometric variables are considered as inputs that affect them. A combined design of experiments (DOE) and differential evolution (DE) approach is proposed. The DOE methodology is used to reduce the search space by eliminating from consideration input variable values, leading to …

An Accurate And Efficient Time Delay Estimation Method Of Ultra-High Frequency Signals For Partial Discharge Localization In Substations, Pengfei Li, Kejie Dai, Tong Zhang, Yantao Jin, Yushun Liu, Yuan Liao

Electrical and Computer Engineering Faculty Publications

Partial discharge (PD) localization in substations based on the ultra-high frequency (UHF) method can be used to efficiently assess insulation conditions. Localization accuracy is affected by the accuracy of the time delay (TD) estimation, which is critical for PD localization in substations. A review of existing TD estimation methods indicates that there is a need to develop methods that are both accurate and computationally efficient. In this paper, a novel TD estimation method is proposed to improve both accuracy and efficiency. The TD is calculated using an improved cross-correlation algorithm based on full-wavefronts of array UHF signals, which are extracted …

Power Utility Tests For Multi-Mw High Energy Batteries, Oluwaseun M. Akeyo, Huangjie Gong, Vandana Rallabandi, Nicholas Jewell, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

This paper reviews the procedures, layouts and metrics described in the new test manual issued by the Electric Power Research Institute (EPRI), in order to determine the performance and functionality of a utility scale battery energy storage system (BESS). In this approach, the large battery unit is connected to the dc-link of a bidirectional power conversion system (PCS), which may be interfaced with either the utility grid or a load bank for the purpose of estimating the BESS operation and performance characteristics, some of which includes; available charge/discharge energy at rated power, continuous charge/discharge duration, battery ramp rate, and ac …

Simulation Studies For A Multi-Mw Hybrid Wind-Solar Pv System For Desalination Plants, Vandana Rallabandi, Nasser Alawhali, Oluwaseun M. Akeyo, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

This paper presents a power system configuration and control schemes for a Multi-MW wind-solar hybrid system, which includes multiple wind turbines and solar panels to support a desalination plant. The wind and solar systems are sized such that the desalination plant obtains, as far as possible, its power from the renewable sources, to minimize the dependence on the utility grid. Each section of the wind turbine system includes a variable speed permanent magnet synchronous generator connected to the grid via a back-to-back voltage source converter. The rectifier operates the wind system at the maximum power point, and the inverter provides …

Real Time Operation Of Smart Homes With Pv And Battery Systems Under Variable Electricity Rate Schedules And Transactive Power Flow, Huangjie Gong, Oluwaseun M. Akeyo, Vandana Rallabandi, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

According to some utility schedules, the electricity rate is variable such that homes may be encouraged to buy and store power in a battery when it is inexpensive, and self-consume or sell to the grid during other times. Power arbitrage through a battery energy storage (BES), can help maintain consumer comfort and minimize residential electricity bills. This paper reports the calculated daily energy costs incurred by different types of homes for a given utility electricity rate schedule. The homes exchange power among each other behind a section of the distribution network. A free market system is formed and the electricity …

Exploring The Efficiency And Cost Limits Of Fractional Hp Axial Flux Pm Machine Designs, Narges Taran, Vandana Rallabandi, Greg Heins, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

Optimizing the design of electric machines is a vital step in ensuring the economical use of active materials. The three-dimensional flux paths in axial flux PM (AFPM) machines necessitate the use of computationally expensive 3D electromagnetic analysis. Furthermore, a large number of design evaluations is required to find the optimum, causing the total computation time to be excessively long. In view of this, a two-level surrogate assisted algorithm capable of handling such expensive optimization problems is introduced, which substantially reduces the number of FEA evaluations. The proposed algorithm is employed to optimally design an AFPM machine within a specified envelope, …

Net Zero Energy Houses With Dispatchable Solar Pv Power Supported By Electric Water Heater And Battery Energy Storage, Huangjie Gong, Vandana Rallabandi, Dan M. Ionel, Donald G. Colliver, Shaun Duerr, Cristinel Ababei

Power and Energy Institute of Kentucky Faculty Publications

Over a year, net zero energy (NZE) houses produce and feed zero net metered electrical energy to the grid. Technical challenges, notably the `duck curve' arise due to the fact that peak solar generation and load demand are seldom coincident. Common approaches to mitigate this limitation include the curtailment of solar power, and the use of storage. Surplus solar energy may be stored in a battery, which can subsequently be discharged to supply the home electricity needs when demand is in excess. In addition to batteries, less expensive electric water heaters, which are ubiquitous, can be modified as energy storage …

Torque Production Capability Of Axial Flux Machines With Single And Double Rotor Configurations, Narges Taran, Greg Heins, Vandana Rallabandi, Dean Patterson, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

Axial flux PM (AFPM) machines are used particularly in applications requiring a compact structure. Their disc shape topology and axial air-gap have lead to a variety of configurations including two popular ones: the yokeless and segmented armature (YASA), and the single-stator single-rotor or single sided machine. In this study, a comprehensive comparative analysis of these configurations is conducted at different magnetic and electric loadings. It is found that at lower loadings, typically employed for air-cooled machines, the torque/ampere characteristics of the YASA machine are almost identical to those of a single sided machine constructed with half the magnet volume. On …

Transistor-Clamped Multilevel H-Bridge Inverter In Si And Sic Hybrid Configuration For High-Efficiency Photovoltaic Applications, Yibin Zhang, Jiangbiao He, Sanjeevikumar Padmanaban, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

Using wide bandgap (WBG) devices has been a promising solution to improve the efficiency of power inverters for photovoltaic (PV) applications. However, for multilevel inverters, using WBG devices to improve the inverter efficiency can increase the system cost dramatically due to the high price of WBG devices in the present market as well as the large number of power devices typically required in multilevel inverter topologies. In this paper, a five-level transistor clamped H-bridge (TCHB) inverter will be further investigated. This inverter requires much lower number of semiconductor switches and fewer isolated dc sources than the conventional cascaded H-bridge inverter. …

Improving The Capacity Factor And Stability Of Multi-Mw Grid Connected Pv Systems With Results From A 1mw/2mwh Battery Demonstrator, Oluwaseun M. Akeyo, Vandana Rallabandi, Nicholas Jewell, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

Conventional PV systems integrated with a battery connect the array and the energy storage unit to a dc-link through individual dc-dc converters for maximum power point tracking (MPPT) and battery charge control. This paper proposes a new system configuration, which connects the PV array and battery unit to the dc-link of the system inverter via a single dc-dc converter capable of simultaneously operating as a charge controller and MPPT device. This dc-dc converter is controlled such that it charges/discharges the battery with the amount of power required to maintain the PV array at its MPPT reference voltage. The proposed system …

Hybrid Pv-Wind, Micro-Grid Development Using Quasi-Z-Source Inverter Modeling And Control—Experimental Investigation, Neeraj Priyadarshi, Sanjeevikumar Padmanaban, Dan M. Ionel, Lucian Mihet-Popa, Farooque Azam

Power and Energy Institute of Kentucky Faculty Publications

This research work deals with the modeling and control of a hybrid photovoltaic (PV)-Wind micro-grid using Quasi Z-source inverter (QZsi). This inverter has major benefits as it provides better buck/boost characteristics, can regulate the phase angle output, has less harmonic contents, does not require the filter and has high power performance characteristics over the conventional inverter. A single ended primary inductance converter (SEPIC) module used as DC-DC switched power apparatus is employed for maximum power point tracking (MPPT) functions which provide high voltage gain throughout the process. Moreover, a modified power ratio variable step (MPRVS) based perturb & observe (P&O) …

Coreless And Conventional Axial Flux Permanent Magnet Motors For Solar Cars, Narges Taran, Vandana Rallabandi, Greg Heins, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

Axial flux permanent magnet (AFPM) motors are suitable options for solar-powered vehicles due to their compact structure and high torque density. Furthermore, certain types of AFPM machines may be configured without stator cores, which eliminates associated losses and cogging torque and simplifies the manufacturing and assembly. This paper examines two machine designs for use in the solar-powered vehicle of the challenger class-a single rotor, single stator conventional AFPM machine, and a coreless AFPM machine with multiple stator and rotor disks. The response surface methodology (RSM) is utilized for the systematic comparison of the conventional and coreless topologies and to select …