Electrical and Electronics Commons^™

Research Tools And Their Uses For Determining The Thermal Inactivation Kinetics Of Salmonella In Low-Moisture Foods, Soon Kiat Lau

Department of Food Science and Technology: Dissertations, Theses, and Student Research

The reputation of low-moisture foods as safe foods has been crumbling over the past decade due to repeated involvement in foodborne illness outbreaks. Although various pasteurization technologies exist, a majority are thermal processes and have not been well-characterized for pasteurizing low-moisture foods. In addition, the nature of a low-moisture food matrix introduces various experimental complications that are not encountered in high-moisture foods. In this dissertation, the development, building instructions, and characterization of various open source tools for studying the inactivation kinetics of microorganisms in low-moisture foods are described. The first tool is the TDT Sandwich, a dry heating device for …

Spectrum Modeling Of Out-Of-Band Intermodulation For Dual-Band Rf Amplifiers In Ofdm Modulation, Xianzhen Yang, Siyuan Yan, Xiao Li, Qiang Wu, Fu Li

Electrical and Computer Engineering Faculty Publications and Presentations

Dual-band RF amplifiers play increasingly important roles in next-generation mobile communication systems including 5G, and the out-of-band intermodulation products are often not negligible since they generate interference to adjacent channels. In this article, following our previous modeling of cross-modulation for amplified dual-band signals, an analytical expression of out-of-band intermodulation for dual-band orthogonal frequency-division multiplexing signals is derived using the third-order intercept points IP₃. The experimental measurement results validate the proposed analytical expression.

On-Site And External Energy Harvesting In Underground Wireless, Usman Raza, Abdul Salam

Faculty Publications

Energy efficiency is vital for uninterrupted long-term operation of wireless underground communication nodes in the field of decision agriculture. In this paper, energy harvesting and wireless power transfer techniques are discussed with applications in underground wireless communications (UWC). Various external wireless power transfer techniques are explored. Moreover, key energy harvesting technologies are presented that utilize available energy sources in the field such as vibration, solar, and wind. In this regard, the Electromagnetic(EM)- and Magnetic Induction(MI)-based approaches are explained. Furthermore, the vibration-based energy harvesting models are reviewed as well. These energy harvesting approaches lead to design of an efficient wireless underground …

Nonlinear Least Squares 3-D Geolocation Solutions Using Time Differences Of Arrival, Michael V. Bredemann

Mathematics & Statistics ETDs

This thesis uses a geometric approach to derive and solve nonlinear least squares minimization problems to geolocate a signal source in three dimensions using time differences of arrival at multiple sensor locations. There is no restriction on the maximum number of sensors used. Residual errors reach the numerical limits of machine precision. Symmetric sensor orientations are found that prevent closed form solutions of source locations lying within the null space. Maximum uncertainties in relative sensor positions and time difference of arrivals, required to locate a source within a maximum specified error, are found from these results. Examples illustrate potential requirements …

Ece Senior Design Project - Cost-Effective Diy Electrometer, Benjamin Hahn

Honors Theses

An electrometer is a critical electrophysiology instrument used to generate minuscule currents for intracellular stimulation of biological neurons. An electrometer also enables simultaneous measurement of the neuron membrane voltage response. This device is necessary to perform accurate stimulation of neurons. However, the cost of commercial electrometers, around $5000, is prohibitive to many researchers, particularly at the high-school or introductory college level. A recent Western Michigan University graduate student, Lucas Essenburg, designed a basic electrometer for $210. His thesis proved that quality electrometers can be constructed for a fraction of the price of commercial-grade equipment.

This project focused on the improvement …

Resonant Metagratings For Spectral And Angular Control Of Light For Colored Rooftop Photovoltaics, Floris Uleman, Andrea Cordaro, Andrea Alù, Albert Polman

Advanced Science Research Center

We designed semitransparent metagrating supercells that enable control over the spectrum and directivity of incident light for applications in photovoltaics with tailored angular appearance. The building block of the supercells is a 100–120 nm wide and 175 nm tall silicon nanowire that shows a strong Mie resonance around λ = 650 nm. By arranging the resonant Mie scatterers into metagratings of increasing pitch (675–1300 nm), we created a Lambertian-like scattering distribution over an angular range of choice. The millimeter-sized metasurfaces were fabricated using electron beam lithography and reactive ion etching. The fabricated metasurface nearly fully suppresses specular reflection on resonance …

Engineering Design I, Hao Su

Open Educational Resources

Introduction to robotics

Effects Of Collision Damage On The Ultimate Strength Of Fpso Vessels, Muhammad Zubair Muis Alie, Dian Ramasari, Taufiqur Rachman, Ristiyanto Adiputra

Makara Journal of Technology

Floating production storage offloading (FPSO) vessels are movable offshore structures. These structures are designed with large dimensions, and their decks are loaded with several types of equipment. During collision damage, the hull and deck parts loaded with equipment are severely affected. Therefore, the ultimate strength of FPSO vessels should be thoroughly checked and evaluated. The objective of the present study is to analyze the ultimate strength of FPSO vessels against collision damage characterized by hogging and sagging under longitudinal bending. The cross section of an FPSO vessel is modeled with elements composed of stiffened and unstiffened plates. The vessel length …

Ionic Conductivity And Electrochemical Properties Of Alginate–Nn4no3-Based Biopolymer Electrolytes For Edlc Application, Norfatihah Binti Mazuki, Nur Muhitul Jalilah Rasali, Bouchta Sahraoui, Ahmad Salihin Samsudin

Makara Journal of Technology

In this work, alginate doped with various contents of ammonium nitrate (NH4NO3) as a solid biopolymer electrolyte (SBE) was prepared via casting by using distilled water as a solvent. Impedance studies on alginate–NH4NO3 SBE films were conducted via impedance spectroscopy. The lowest bulk resistance (Rb) showed that the maximum ionic conductivity of the sample containing 25 wt.% NH4NO3 at ambient temperature (303 K) was 5.56 × 10−5 S cm−1. The temperature dependence of ionic conductivity was evaluated, and results confirmed that electrolytes followed an Arrhenius behavior. The highest conducting sample was fabricated into an electrical double-layer capacitor and characterized in …

Synthesis Of Epoxy Monoethanolamide From Bauhinia Monandra Seed Oil, Adewale Adewuyi, Rotimi A. Oderinde

Makara Journal of Technology

In this study, we synthesized epoxidised monoethanolamide (EMA) from Bauhinia monandra seed oil (BMO) via a simple reaction route. In this process, BMO was transesterified to obtain a mixture of methyl esters, which was subjected to a urea adduct complexation reaction. The unsaturated methyl esters (BME) from the urea adduct complexation reaction were then epoxidised using performic acid produced in situ in a one-pot reaction system. The epoxidised methyl esters were converted to EMA by reacting them with monoethanolamine (1:10). The progression of the reaction was monitored using Fourier transform infrared spectroscopy and proton nuclear magnetic resonance spectroscopy, and the …

Ethylene Carbonate And Polyethylene Glycol As Efficient Plasticizers In Cmc-Pva-Nh4no3-Based Polymer Electrolyte, Noor Saadiah Mohd Ali, Yuki Nagao, Ahmad Salihin Samsudin

Makara Journal of Technology

This study investigated the influence of plasticizers (polyethylene glycol [PEG] and ethylene carbonate [EC]) on the ionic conduction of CMC-PVA-NH4NO3. Blended biopolymer electrolytes (BBEs) based on carboxymethyl cellulose–polyvinyl alcohol (CMC-PVA) doped with ammonium nitrate (NH4NO3) were obtained via casting solution technique incorporated with PEG and EC, which acted as plasticizers. Electrical impedance spectroscopy (EIS) was conducted to evaluate the effect of plasticization on the ionic conduction properties. The ionic conductivity improved from 1.70 × 10−3 S/cm for un-plasticized BBEs to 3.92 × 10−3 S/cm for plasticized BBEs with EC and 3.00 × 10−3 S/cm for plasticized BBEs with PEG. The …

Current Status Of Hydrothermal Treatment For Energy And Material Recovery Toward A Sustainable Post-Consumer Material Cycle, Baskoro Lokahita, Muhammad Aziz, Fumitake Takahashi

Makara Journal of Technology

The demand for energy-efficient and environmentally friendly municipal solid waste (MSW) processing has increased in developing countries. The thermochemical process offers a fast and reliable solution to reutilize or reduce the volume of MSW. Hydrothermal treatment is a novel MSW treatment technology that is compatible with high-moisture-content feedstock. It involves the thermal degradation of MSW in pressurized water or steam, which promotes the disintegration of cellulosic and polymer materials. Recent advances have shown effective MSW conversion into homogenous solid hydrochar with higher energy density. Alkali and chlorine content, which causes issues in combustors, was successfully removed due to the washing …

Liquefaction Potential Analysis Based On Nonlinear Ground Response On The Coastline Of Bengkulu City, Indonesia, Lindung Zalbuin Mase

Makara Journal of Technology

This paper presents the study of the seismic response and liquefaction potential of the coastal area of Bengkulu City during the September 2007 Sumatra earthquake. The study is conducted by collecting site investigation data (standard penetration test) and applying input motion to observe soil response. Synthetic ground motion is generated by considering the important aspects of earthquakes, including focal depth, epicenter, earthquake source, and site classification. The synthetized ground motion is then used as the input motion in the seismic response analysis. The results of this analysis are spectral acceleration and peak ground acceleration at each depth. The resulting spectral …

Comparison Of Phytoremediation And Filtration For Diamond-Mine-Tailings Water Treatment, M. Hafidhuddin Noor, Mijani Rahman, Akhmad Gazali, Nia Kania, Aulia Rahma, Erdina L.A. Rampun, Amalia E. Pratiwi, Muthia Elma

Makara Journal of Technology

The water pollution caused by diamond mine activities can kill aquatic life. In this work, we used phytoremediation and filtration to treat pond water polluted by the tailings of a diamond mine located in South Kalimantan, Indonesia. Einchhornia crassipes (water hyacinth) was utilized as the biomass for the phytoremediation process. Gravel (10–15 mm) and sand (0.1–1 mm) were used as filter media in the simple filtration setup, using an up-flow system (bottom to top). In the experiment, 16 L of diamond tailing water was poured into five phytoremediation reactors (each 60 L in volume), which were then tested over seven …

Characterization And Sensitivity Analysis Of 6 Meter Cassegrain Antenna, James L. Harris

Theses and Dissertations

This paper will characterize a 6 meter in diameter cassegrain antenna. The cassegrain antenna is a special form of a dual reflector antenna which uses a main reflector following a parabolic curve and a sub reflector which follows a hyperbolic curve. Cassegrain style antennas have multiple parameters which can be tuned to achieve specific design goals. Performing a sensitivity analysis will establish relationships between design parameters, directivity, side lobe levels, and effects of strut geometry. The initial design parameters will be assumed based on typical values. Results from the sensitivity analysis will be used to provide a performance band for …

A Non-Destructive Evaluation Application Using Software Defined Radios And Bandwidth Expansion, Nicholas J. O'Brien

Theses and Dissertations

The development of low-complexity, lightweight and low-cost Non-Destructive Evaluation (NDE) equipment for microwave device testing is desirable from a maintenance efficiency and operational availability perspective. Current NDE equipment tends to be custom-designed, cumbersome and expensive. Software Defined Radio (SDR) technology, and a bandwidth expansion technique that exploits a priori transmit signal knowledge and auto-correlation provides a solution. This research investigated the reconstruction of simultaneous SDR receiver instantaneous bandwidth (sub-band) collections using single, dual and multiple SDR receivers. The adjacent sub-bands, collectively spanning a transmit signal bandwidth were auto-correlated with a replica transmit signal to restore frequency and phase offsets. The …

Near Real-Time Zigbee Device Discrimination Using Cb-Dna Features, Yousuke Z. Matsui

Theses and Dissertations

Currently, Low-Rate Wireless Personal Area Networks (LR-WPAN) based on the Institute of Electrical and Electronics Engineers (IEEE) 802.15.4 standard are at risk due to open-source tools which allow bad actors to exploit unauthorized network access through various cyberattacks by falsifying bit-level credentials. This research investigates implementing a Radio Frequency (RF) air monitor to perform Near RealTime (NRT) discrimination of Zigbee devices using the IEEE 802.15.4 standard. The air monitor employed a Multiple Discriminant Analysis/Euclidean Distance classifier to discriminate Zigbee devices based upon Constellation-Based Distinct Native Attribute (CB-DNA) fingerprints. Through the use of CB-DNA fingerprints, Physical Layer (PHY) characteristics unique to …

Syllabus Ee330 Electromagnetics, Nicholas Madamopoulos

Open Educational Resources

Concepts covered in the undergraduate electrical engineering class of electromagnetics

Dartmouth Formula Racing: Full Electric Battery System Design, Matt Gardner, Jacob Hagler, Ruthie Nordhoff, Otto Salmi

ENGS 89/90 Reports

Dartmouth Formula Racing (DFR) lacked an electrical energy storage system that was Formula Hybrid rules-compliant, optimized for FH events, safe, reliable, and integrated with the rest of their vehicle. Additionally, the team lacked the academic and professional resources required to bring a thorough, analytical approach to the design, testing, and documentation of the new storage system. Our team designed and built a Lithium-Ion battery pack (accumulator) containing energy storage, active cooling, battery management and temperature monitoring systems, and control circuitry compatible with DFR’s vehicle. Collaboration throughout design, fabrication, assembly and testing processes ensured effective knowledge transfer to the DFR team.

Dashboard-Mounted Driver Monitoring System, Daniel Lein, Prahlad Sarma, William Roussell, Nathan Nuñez, Elvis Manzanares

ENGS 89/90 Reports

The objective of this project is to deliver safe DMS hardware and interfacing/preprocessing software on which Toyota can run its drowsiness detection neural net. The system shall: securely house all necessary imaging, electronic, and computer hardware to output facial recognition data to the car’s computer, without data input from any other car system; obscure less than 10% of the driver’s field of view out of a standard windshield; be able to capture and process images such that the image classification neural net recognize the images, meeting the top-1 benchmark accuracy statistic across static and dynamic car-cabin lighting conditions; and meet …

Neca Ghana Project, Michael T. Klee

Construction Management

Cal Poly’s motto is, “Learn by Doing" and for Cal Poly’s NECA Chapter, this isn’t simply a motto, but a directive for proactive change. For my senior project I will be leading the Cal Poly NECA chapter in the design, pre- fabrication and construction of a 5-7kw solar array, community center, ice production room and technology room in the remote fishing village of Agbokpa, Ghana. The solar array will power multiple industrial DC freezers, high efficiency LED lighting and charging stations while additionally powering water filtration and irrigation systems. Like many other fishing villages around the world, Agbokpa has no …

Development Of A Drone-Mounted Wireless Attack Platform, Nathan V. Barker

Theses and Dissertations

The commercial drone market has grown rapidly due to the increasing utility and capabilities of drones. This new found popularity has made it possible for inexpensive drones capable of impressive carry capacities and flight times to reach the consumer market. These new features also offer an invaluable resource to wireless hackers. Capitalizing on their mobility, a wireless hacker can equip a drone with hacking tools to surpass physical security (e.g. fences) with relative ease and reach wireless networks. This research seeks to experimentally evaluate the ability of a drone-mounted wireless attack platform equipped with a directional antenna to conduct wireless …

Improved Ground-Based Monocular Visual Odometry Estimation Using Inertially-Aided Convolutional Neural Networks, Josiah D. Watson

Theses and Dissertations

While Convolutional Neural Networks (CNNs) can estimate frame-to-frame (F2F) motion even with monocular images, additional inputs can improve Visual Odometry (VO) predictions. In this thesis, a FlowNetS-based [1] CNN architecture estimates VO using sequential images from the KITTI Odometry dataset [2]. For each of three output types (full six degrees of freedom (6-DoF), Cartesian translation, and transitional scale), a baseline network with only image pair input is compared with a nearly identical architecture that is also given an additional rotation estimate such as from an Inertial Navigation System (INS). The inertially-aided networks show an order of magnitude improvement over the …

Residential Thermal Storage And Cooling, Joao Marcelo Rocha Belmonte, Jacob Anderson, Andrew Clarke, Daphne Forester, Bianca Hardtke, Josh Hartman, Marc D. Compere

Sustainability Conference

No abstract provided.

A Hop-By-Hop Relay Selection Strategy In Multi-Hop Cognitive Relay Networks, Hui Sun, Mort Naraghi-Pour, Weixing Sheng, Renli Zhang

Faculty Publications

In this paper, a hop-by-hop relay selection strategy for multi-hop underlay cognitive relay networks (CRNs) is proposed. In each stage, relays that successfully decode the message from previous hop form a decoding set. Taking both maximum transmit power and maximum interference constraints into consideration, the relay in the decoding set which has the largest number of channels with an acceptable signal-to-noise ratio (SNR) level to the relays in the next stage is selected for retransmission. Therefore, relay selection in each stage only relies on channel state information (CSI) of the channels in that stage and does not require the CSI …

Dual-Axis Solar Tracker, Bryan Kennedy

All Undergraduate Projects

Renewable energies, and fuels that are not fossil fuel-based, are one of the prolific topics of debate in modern society. With climate change now becoming a primary focus for scientists and innovators of today, one of the areas for the largest amount of potential and growth is that of the capturing and utilization of Solar Energy. This method involves using a mechanical system to track the progression of the sun as it traverses the sky throughout the day. A dual-axis solar tracker such as the one designed and built for this project, can follow the sun both azimuthally and in …

Ensemble Lung Segmentation System Using Deep Neural Networks, Redha A. Ali, Russell C. Hardie, Hussin K. Ragb

Electrical and Computer Engineering Faculty Publications

Lung segmentation is a significant step in developing computer-aided diagnosis (CAD) using Chest Radiographs (CRs). CRs are used for diagnosis of the 2019 novel coronavirus disease (COVID-19), lung cancer, tuberculosis, and pneumonia. Hence, developing a Computer-Aided Detection (CAD) system would provide a second opinion to help radiologists in the reading process, increase objectivity, and reduce the workload. In this paper, we present the implementation of our ensemble deep learning model for lung segmentation. This model is based on the original DeepLabV3+, which is the extended model of DeepLabV3. Our model utilizes various architectures as a backbone of DeepLabV3+, such as …

Rc Mini Baja Car - Suspension And Chassis, Collin Mckenzie

All Undergraduate Projects

Two students have developed a unique design of the RC Baja Car to optimize functionality and performance. A Baja car is a remote controlled 1/10 scale car that is used for recreation or competition, usually meant for competing in the ASME Baja car competition versus various schools. The competition focuses on the best time achieved in different courses that utilize speed, turns, and jumps. The objective for the project was to create a unique suspension from previous individual’s projects by creating a four-link suspension in which allows more travel in the suspension of the car and maintains functionality with the …

Calibration To Mitigate Near-Field Antennas Effects For A Mimo Radar Imaging System, Ha Hoang, Matthias John, Patrick Mcevoy, Max Ammann

Articles

A calibration method for a high-resolution hybrid MIMO turntable radar imaging system is presented. A line of small metal spheres is employed as a test pattern in the calibration process to measure the position shift caused by undesired antenna effects. The unwanted effects in the antenna near-field responses are analysed, modelled and significantly mitigated based on the symmetry and differences in the responses of the MIMO configuration.

Ultra-Low Power Circuits And Architectures For Neuromorphic Computing Accelerators With Emerging Tfets And Rerams, Jie Lin

Electronic Theses and Dissertations, 2020-2023

Neuromorphic computing using post-CMOS technologies is gaining increasing popularity due to its promising potential to resolve the power constraints in Von-Neumann machine and its similarity to the operation of the real human brain. To design the ultra-low voltage and ultra-low power analog-to-digital converters (ADCs) for the neuromorphic computing systems, we explore advantages of tunnel field effect transistor (TFET) analog-to-digital converters (ADCs) on energy efficiency and temperature stability. A fully-differential SAR ADC is designed using 20 nm TFET technology with doubled input swing and controlled comparator input common-mode voltage. To further increase the resolution of the ADC, we design an energy …