Electrical and Electronics Commons^™

Utilization Of Distributed Generation In Power System Peak Hour Load Shedding Reduction, Nandu Balachandran

LSU New Orleans Theses and Dissertations

An approach to utilize Distributed Generation (DG) to minimize the total load shedding by analyzing the power system in Transactive energy framework is proposed. An algorithm to optimize power system in forward and spot markets to maximize an electric utility’s profit by optimizing purchase of power from DG is developed. The proposed algorithm is a multi-objective optimization with the main objective to maximize a utility’s profit by minimizing overall cost of production, load shedding, and purchase of power from distributed generators. This work also proposes a method to price power in forward and spot markets using existing LMP techniques. Transactive …

Sensitivity Analysis Of Synchronous Generators For Real-Time Simulation, Sowmya Munukuntla

LSU New Orleans Theses and Dissertations

The purpose of this thesis is to validate generator models for dynamic studies of power systems using PSS/E (Power System Simulator for Engineering), EMTP (ElectroMagnetic Transient Program), and Hypersim. To thoroughly evaluate the behavior of a power system in the three specified software packages, it is necessary to have an accurate model for the power system, especially the generator which is of interest. The effect of generator modeling on system response under normal conditions and under faulted conditions is investigated in this work. A methodology based on sensitivity analysis of generator model parameters is proposed aiming to homogenize the behavior …

Test Plan For Real-Time Modeling & Simulation Of Single Pole Switching Relays, Ram Mohan Sanaboyina

LSU New Orleans Theses and Dissertations

A real-time simulator (RTS) with digital and analog input/output modules is used to conduct hardware-in-the-loop simulations to evaluate performance of power system equipment such as protective relays by exposing the equipment to the simulated realistic operating conditions. This work investigates the use of RTS to test relays with single-pole-switching (SPS) feature. Single-pole switching can cause misoperations due to fault arc during reclosing of the breakers. Through this investigation, a test procedure appropriate for the testing SPS relays has been developed. The test procedure includes power system modeling for real time simulation, relay test setup, and test plan. HYPERSIM real-time simulator …

Smart Gate Driver Design For Silicon (Si) Igbts And Silicon-Carbide (Sic) Mosfets, Abdulaziz Alghanem

Electrical Engineering Undergraduate Honors Theses

The design of an efficient and smart gate driver for a Si IGBT and SiC MOSFET is addressed in thesis. First, the main IGBT parameters are evaluated thoroughly in order to understand their effects in the design of the gate driver. All known consequences of previously designed gate drivers are studied in order to achieve an optimum gate driver. As a result of this assessment, the designer is able to determine whether adding or removing components from the gate driver circuit are beneficial or not. Then, exhaustive research is done to identify suitable integrated circuits to use for the power …

High Step-Up/Down Transformerless Multilevel Converter For Renewable Energy Applications, Haider Ghazi Mhiesan

Graduate Theses and Dissertations

This thesis focuses on a high step-up/down transformerless dc-dc modular multilevel converter (MMC) that would be applicable to dc power systems. The design achieves high voltage ratios for interfacing renewable energy sources such as photovoltaic and line interactive Uninterruptible Power System (UPS) systems. The circuit topology provides for high step-up/down dc-dc conversion ratios using an MMC approach operating in resonant mode in order to improve overall efficiency. This topology operates to step-up the input voltage with 1:10 or larger conversion ratio. As a bidirectional converter, it also provides step-down capability at the same voltage ratio (10:1 or greater). The MMC …

Solar Tracking And Lighting Design For A Multimedia Sculpture, Alexandra Ferguson

Honors Theses

A lighting system utilizing solar energy was built to illuminate a wireframe multimedia sculpture. Increased power generation from the solar cells was achieved using a solar tracking mechanism. Color-selectable light emitting diodes were used to provide the user with unlimited customization options. A digital control system was designed using an Arduino® microcontroller to configure the color of the lights and the positioning of the solar panel. The sculpture will create a sense of community and sustainability among students at the school.

Impact Of Clustering Microgrids On Their Stability And Resilience During Blackouts, Mahmoud S. Saleh, Ammar Althaibani, Yusef Esa, Yassine Mhandi, Ahmed Mohamed

Publications and Research

In this paper, the impact of clustering multiple microgrids during blackouts, on their stability and supply availability, will be investigated. Microgrids have the capability of satisfying their emergency loads during blackouts. However, distributed energy resources (DERs)-dominated microgrids are affected by the uncertainty of their input energy supply, e.g. impact of solar irradiance on photovoltaic (PV) output. Moreover, an individual islanded microgrid is prone to instability issues due to large sudden load/generation changes. In order to increase the supply security, and enhance system stability, we propose to use the existing distribution grid infrastructure, if applicable, during blackouts to form microgrid clusters. …

Ingan Leds For General Lighting: Overcoming Efficiency Droop At High Current Injection, Nicolas Andrade

AUCTUS: The Journal of Undergraduate Research and Creative Scholarship

According to the Energy Information Administration's Annual Energy Outlook report in 2011, the United States alone consumed 97.8 quadrillion Btus (quads) of primary energy in 2010. Roughly 41% of this energy was consumed for electricity use, with 18% of the electricity being dedicated to lighting. The International Energy Agency (IEA) estimated light consumption of this scale translates to CO2 production equivalent to 70% of the emissions from all of the world's light passenger vehicles. Pollution levels at this rate caused 18,200 premature deaths, 2,100,000 days of medication, and 29 million cases of lower respiratory symptoms.

Solid-State Transformers For Interfacing Solar Panels To The Power Grid: An Optimum Design Methodology Of A High Frequency Transformer For Dc-Dc Converter Applications, Kenny George

Inquiry: The University of Arkansas Undergraduate Research Journal

Nowadays the use of power electronic interfaces to integrate distributed generation with the power grid is becoming relevant due to the increased penetration of renewable energy sources like solar, and the continued interest to move to a smarter and more robust electric grid. Those interfaces, which also provide a voltage step-up or step-down function, are of particular interest because renewable energy sources do not always have voltages compatible with the connecting grid. Among them, the so-called “power electronic transformer” or “solid-state transformer” (SST) is the focus of significant research. Advantages such as bidirectional power flow, improved system control, reduced size, …

Supervision Of Community Based Microgrids: An Economic Model Predictive Control Approach, Francesco Tedesco, Lubna Mariam, Malabika Basu, Alessandro Casavola, Michael F. Conlon

Conference papers

Abstract— In this paper, an Economic Model Predictive Control (EMPC) approach has been presented to manage a Community-based microgrid (C-µGCC) at the pricing level. The main task is at satisfying the demand at prosumer sides and, at the same time, optimizing various µ-Grid contrasting objectives. Emphasis has been given to the operational constraints related to the components lifetime, whose satisfaction would be beneficial for the grid in that the maintenance and replacement costs would be reduced. A simulative analysis has been carried out on the basis of available measured data related to a location in Dublin, Ireland. Results show the …

Genetic Algorithms In Stochastic Optimization And Applications In Power Electronics, Mengmei Liu

Theses and Dissertations--Electrical and Computer Engineering

Genetic Algorithms (GAs) are widely used in multiple fields, ranging from mathematics, physics, to engineering fields, computational science, bioinformatics, manufacturing, economics, etc. The stochastic optimization problems are important in power electronics and control systems, and most designs require choosing optimum parameters to ensure maximum control effect or minimum noise impact; however, they are difficult to solve using the exhaustive searching method, especially when the search domain conveys a large area or is infinite. Instead, GAs can be applied to solve those problems. And efficient computing budget allocation technique for allocating the samples in GAs is necessary because the real-life problems …

Wide-Band Gap Devices For Dc Breaker Applications, Olukayode O. Sodipe

Master's Theses

With the increasing interest in wide-band gap devices, their potential benefits in power applications have been studied and explored with numerous studies conducted for both SiC and GaN devices. This thesis investigates the use of wide-band gap devices as the switching element in a semiconductor DC breaker. It involves the design of an efficient semiconductor DC breaker, its simulation in SPICE, construction of a hardware prototype and the comparative study of SiC and Si versions of the aforementioned breaker. The results obtained from the experiments conducted in the process of concluding this thesis show that the SiC version of the …

Modeling, Simulation And Control Of Hybrid Electric Vehicle Drive While Minimizing Energy Input Requirements Using Optimized Gear Ratios, Sanjai Massey

Dissertations, Master's Theses and Master's Reports

This project was conducted to analyze (model and simulate) and optimize an electric motor based drive system to propel a typical passenger vehicle in an urban driving environment. Although there are many HEV and EV type systems on the market today, this paper chose the Toyota Prius HEV system as a baseline using a brushless AC motor.

Although a vehicle can be driven many ways, a more standardized Urban Dynamometer Driving Schedule, UDDS, was chosen to simulate real driving conditions. This schedule is determined by the US Environmental Protection Agency, EPA, and is intended to represent the city driving conditions …

Electromechanics Of An Ocean Current Turbine, Vasileios Tzelepis

LSU New Orleans Theses and Dissertations

The development of a numeric simulation for predicting the performance of an Ocean Current Energy Conversion System is presented in this thesis along with a control system development using a PID controller for the achievement of specified rotational velocity set-points. In the beginning, this numeric model is implemented in MATLAB/Simulink® and it is used to predict the performance of a three phase squirrel single-cage type induction motor/generator in two different cases. The first case is a small 3 meter rotor diameter, 20 kW ocean current turbine with fixed pitch blades, and the second case a 20 …

An Organic Mixed Ion-Electron Conductor For Power Electronics, Abdellah Malti, Jesper Edberg, Hjalmar Granberg, Zia Ullah Khan, Jens W. Andreasen, Xianjie Liu, Dan Zhao, Hao Zhang, Yulong Yao, Joseph W. Brill, Isak Engquist, Mats Fahlman, Lars Wågberg, Xavier Crispin, Magnus Berggren

Physics and Astronomy Faculty Publications

A mixed ionic–electronic conductor based on nanofibrillated cellulose composited with poly(3,4-ethylene-dioxythio­phene):­poly(styrene-sulfonate) along with high boiling point solvents is demonstrated in bulky electrochemical devices. The high electronic and ionic conductivities of the resulting nanopaper are exploited in devices which exhibit record values for the charge storage capacitance (1F) in supercapacitors and transconductance (1S) in electrochemical transistors.

Dual-Input Dc-To-Dc Converter Topologies And Control Schemes, Shaun Alan Stickel

Boise State University Theses and Dissertations

Dual-input DC-to-DC converters are power supplies that draw power from two sources simultaneously and deliver power to a single load, the ratio of power drawn from each source and be held constant with changes in the load. Applications for dual-input power supplies are computer systems, mobile systems using energy harvesting, and systems needing redundant power supplies. This writing covers the operation and control of dual-input DC-to-DC converters that implement a non-inverting buck-boost function and utilize only a single power path.

Traditionally, a dual-input power supply is created by placing two standard power paths in parallel. This adds considerable control complexity …

Model Development And Validation For Wind Generation Transmission Systems, Mahmood Shihadeh Saadeh

Graduate Theses and Dissertations

In this research a new benchmark system is proposed for wind energy transmission systems. New model development, validation, and calibration methods for power transmission systems are proposed and implemented as well. First, a model reduction criteria is chosen based on electrical interconnection and geographical information. Model development is then done using reduction techniques on an operation model provided by a transmission operator based on the chosen criteria. Then model validation is performed using actual PMU synchrophasor measurements provided by a utility company. The model development and validation process ensures the accuracy of the developed model and makes for a realistic …

High-Frequency Transformer Design For Solid-State Transformers In Electric Power Distribution Systems, Roderick Javier Garcia Montoya

Graduate Theses and Dissertations

The objective of this thesis is to present a high- or medium-frequency transformer design methodology for Solid-State Transformer (SST) applications. SSTs have been proposed as a replacement of the traditional 50/60 Hz transformer in applications demanding high-power density. Moreover, due to the high penetration of distributed generation, DC grids, energy storage systems, and sensitive loads, SSTs have been considered as an enabling technology for envisioned future energy systems. These applications demand additional functionalities that may not be achieved with traditional transformers. For example, active power flow control, harmonic suppression, voltage regulation, voltage sag compensation, and reduced size and volume.

In …

Accelerated Aging Test On Multiple Xlpe Mv Cables Simultaneously To Induce Water Trees, Shane Conlan, Jane Courtney, Tom Looby

Conference papers

The objective of this paper is to develop an accelerated ageing test to induce water tree growth which is capable of testing up to ten 10 kV cable samples simultaneously. An existing accelerated ageing method was used as a basis for this project. This method uses a high frequency power supply (3 kHz) to achieve a test duration of 14 days. Modifications were made to this method to allow for multiple samples to be tested simultaneously. A specially designed variable inductor was utilised in a parallel RLC resonance circuit. This resonance circuit limits the current draw from a high frequency …

Enterprise Smart Outlet, David Faltmier, Matthew Mcgill, Luke Stencel

Electrical Engineering

The purpose of our senior project, Enterprise Smart Outlet, is to create an electrical outlet which will allow enterprise users to monitor and change their power consumption habits on a large scale. The initial goal of this project is to allow consumers to see their power consumption per outlet in real time, and then using that information conform their future habits to help them conserve electrical energy, and more importantly, money. Three requirements for our project to meet our initial goal are, the outlet will work in a standard electrical outlet and be completely compatible with current electrical standards, the …

Current Protection For The Energy Harvesting From Exercise Machines (Ehfem) Project, Colton Crivelli

Electrical Engineering

The Energy Harvesting from Exercise Machines (EHFEM) project intends to create an exercise machine that recycles the energy expended by an athlete operating the machine by sending it to the electric grid. The work done by the user goes through a DC-DC converter and an inverter in order to prepare it for delivery to the grid. A protection circuit ensures that the inverter does not try to pull too much current from the DC-DC converter. The project implements a current protection system that ensures the system doesn’t experience an overcurrent condition.

The Dc House Project: Electrical System Design & Construction, John Bradley

Electrical Engineering

This project entails the design and assembly of the photovoltaic system, switchboard panel enclosure, and battery enclosure for the DC House’s main electrical system. The intended purpose of this project is to provide the electrical framework necessary for future students to easily modify and add to this rendition of the DC House. The principle design implements a variety of renewable energy sources, however this senior project only uses solar power in order to maintain a manageable scope. Each of these renewable energy sources are stepped down to a voltage of 24V and input to a Multi Input Single Output DC …

Veloelectric: Creating A Device That Harvests Energy From Bicycles, Austin Hall, Daniel Stohr, Tj Fox

Mechanical Engineering

Long distance mountain bikers, bike-packers, and many bikers in developing countries rely on electrical devices for safety and communication. These specific groups of people operate in areas with little to no electricity, and often times have no power to sustain their devices. The purpose of this Cal Poly senior project, VeloElectric, was to design, build, and test a kinetic energy harvester for bicycles that can be used to charge common mobile devices via USB. This senior project team created a device that attaches directly to a bicycle and uses vibrations to generate energy, which in turn powers a variety of …

The Electric Reel For Soccer Fields, Stephen Taylor

Electrical Engineering

Painting a soccer field consumes too much time. The process of reeling the string after laying out string along the field needs to improve. As a result, my project addresses improvements in how the workers retrieve the string through the production of an electric reel. This electric reel allows the worker to have control of the speed, direction, and on/off state of the device. Direction control allows the user ability to reel and unwind the string. Variable speed allows the user to control how fast the reel unwinds and reels the string. The device gathers string in an orderly manner …

Sun-Tracking Solar-Powered Led Street Light, Wesley Ballar, Harrison Wong

Electrical Engineering

Street lighting is an essential utility especially in urban and industrialized areas because it provides illumination and safety for vehicles and pedestrians throughout the night. However, street lights are relatively inefficient; they consume large amounts of power from electrical grids and have predetermined operation times that are often non-optimal for the surrounding environment. The Sun-Tracking Solar-Powered LED Street Lamp is a self-sustaining device, built to replace the current lighting sources. The device features sun-tracking capabilities for maximum energy gathering and darkness recognition to establish optimal operation times. The project provides a reliable and enhanced alternative to current street lighting systems.

Adaptive Automotive Lighting Systems, Marc W. Haeberlin

Master's Theses

Over the past few years, the use of LEDs within the automotive and avionic industries has increased due to their high efficiency, durability and wide range of light brightness. As the use of LEDs within these industries grows, a need for reliable, high performance drivers becomes more relevant. Companies are implementing LEDs for applications involving adaptive lighting or simple dimming features. This thesis shows implementation of various non-isolated analog converters integrated with digital dimmers to achieve these adaptive lighting systems. Adaptive lighting systems involve reading an input from an external source (brake pedal or steering wheel) and changing the brightness …

Universal Programmable Battery Charger With Optional Battery Management System, Michael Duke Desando

Master's Theses

This report demonstrates improvements made in battery charging and battery management technology through the design of a universal programmable battery charger with optional battery management system attachment. This charger offers improvements in charge efficiency and unique battery charging algorithms to charge a variety of battery chemistries with variety of power requirements. Improvements in efficiency result from a synchronous Buck Controller topology as compared to previous universal chargers that use asynchronous Buck-Boost Converter topologies. This battery charger also surpasses current universal battery chargers by offering different charge modes for different battery chemistries. Charge modes provide the user an option between extending …

Evaluating The Level Of Harmonic Distortion In A Typical Distribution Feeder, Wessen S. Bogale

UNLV Theses, Dissertations, Professional Papers, and Capstones

Steady-state analysis of electrical power systems is largely based on linear and sinusoidal AC circuits which allow the concept of impedance, phasors and well-defined power quantities (i.e., real, reactive and apparent powers). In reality, however, the electric load which was once composed of linear elements (e.g., induction motors, incandescent lighting, etc …) is becoming more and more nonlinear due to the wide-spread use of electronic components such as fluorescent lighting and variable-frequency drives that power the majority of electric motors. As a consequence, the current drawn by such devices is often distorted, thus containing a number of high frequency harmonics …

Secondary Re-Use Of Batteries From Electric Vehicles For Building Integrated Photo-Voltaic (Bipv) Applications, Fintan Mcloughlin, Michael Conlon

Reports

PV Crops is evaluating the use of battery technologies such as Vanadium Redox within Building Integrated Photovoltaic (BIPV) applications. However, their inclusion into BIPV systems will inevitably raise the overall costs of such systems. As a result, PV Crops is looking at other measures in parallel to help lower the costs associated with such systems. One particular area of interest is the potential secondary re-use of battery technology from Electric Vehicle (EV) market as a way of mitigating high costs of such systems as well as a means of encouraging battery recycling.

The global installed capacity for Photovoltaic’s (PV) connected …

Three-Phase Generation Using Reactive Networks, Tattiana Karina Coleman Davenport

Master's Theses

Household appliances utilize single-phase motors to perform everyday jobs whether it is to run a fan in an air conditioner or the compressor in a refrigerator. With the movement of the world going “green” and trying to make everything more efficient, it is a logical step to start with the items that we use every day. This can be done by replacing single-phase motors with three-phase motors in household appliances. Three-phase motors are 14% more efficient than single-phase motors when running at full load and typically cost less over a large range of sizes [1]. One major downside of incorporating …