Electrical and Electronics Commons^™

Energy Harvesting From Exercise Machines: Lt8705 Dc-Dc Conversion For Elliptical Trainers, Braden Burk, Raj Bhula, Nathan Mckay

Electrical Engineering

Cal Poly’s Energy Harvesting from Exercise Machines (EHFEM) program aims to power the grid using human energy harvested from exercise machines in its gym. Doing so could save the school money and increase the total supply of power available on the grid. This document belongs to one of many groups attempting to design a suitable DC-DC conversion system for an elliptical trainer using an LT8705 Four-Switch Buck-Boost converter. Past teams have built other converters and developed system compatibility characteristics such as filtering, safety, and stability for interfacing components. These teams fall into one of two departments in EHFEM: DC-DC Conversion …

Metal Assisted Nanowire Growth For Silicon Nanowire/Amorphous Silicon Composite Solar Cell, Asmaa Ali Sadoon

Graduate Theses and Dissertations

Solar cells are photovoltaic devices that convert the energy of light to electricity by the photovoltaic effect. Crystalline silicon-based solar cells are the most dominant solar cells in the market today due to the high efficiency and relatively low cost. However, the cost of such solar cell is still high due to the large amount of material that is consumed in fabricating such a device. Polycrystalline/amorphous thin films and nanomaterial technologies have emerged to reduce the high cost of c-Si based solar cells and increase the efficiency. In this research, we combined these two technologies to propose and fabricate silicon …

Microprocessor Management Of Energy Harvesting Buck Boost Converters, Timothy O'Sullivan

Electrical Engineering

No abstract provided.

High Voltage Pulse-Width Generator For The Algae Biofuel Project, Philip Yu, Stephen Leung

Electrical Engineering

This purpose of this project, sponsored by Boeing and advised by Dr. Arakaki and Dr. Taufik, is to build a high voltage pulse width generator that lyses algae cells to harvest the biofuel within. This project uses Emmanuel Loza's thesis on a cascaded high voltage converter with variable control to build a portable pulse width generator with independent control on the peak voltage, pulse width, and frequency. The project focuses on creating a pulse width generator capable of finding the most optimal pulsed electric field to lyse algae. The pulse width module ranges from 10V-80V peak voltage, 60Hz-100 kHz frequency, …

A Prototype Microwave Cavity Control Circuit For Use In Next Generation Free Electron Laser, Josh Thompson, Peter Neal Barrina, Jiayi Jiang, Joe Frisch, Steve Smith, Daniel Van Winkle

STAR Program Research Presentations

One of the current programs at SLAC National Accelerator Laboratory is the Linac Coherent Light Source, or LCLS. Using the existing hardware of the last third of their linear accelerator (or “linac”), SLAC has created one of the most energetic X-ray free electron lasers (or “FEL”). Since 2009, LCLS has used this FEL to perform a wide range of experiments across all sciences, most notably ultrafast filming at the molecular scale. As requests for beam-time with this laser increases, SLAC is purposing a linac upgrade to better match this demand. This upgrade, named LCLS-II, will replace existing copper radio frequency …

Simulation Of A Smart Home Energy Management System With Dynamic Price Response, Jason Y. Chan, Qinran Hu

Pursuit - The Journal of Undergraduate Research at The University of Tennessee

With the continuing development of the smart grid combined with the fluctuating nature of the electricity market, the development of demand-side management with controllable loads have been greatly driven. With the amount of household loads in the residential sector, managing their energy usage has received lots of interest. This paper presents a simulation of a previously proposed hardware design of a smart home energy management system (SHEMS), focusing on the data collection and processing functions of the proposed design while implementing them onto standard household loads like an electric water heater and an electric vehicle charging station. It was found …

Smart Wall Outlet Design And Implementation For The Dc House Project, Kevin Roy Mendoza

Master's Theses

Most everyday AC appliances are designed to operate off of 120V coming from the wall outlet in our homes. This voltage is a standard set from our established infrastructure. Unlike AC devices, DC devices do not have any set standard of voltage they all will run off of. This presents a problem for the DC house as the various loads that will be used will have different required input voltages. One set voltage for a wall outlet will not suffice for the DC House. This Smart Wall Outlet is designed with a DC-DC converter that will have its output voltage …

Dual High-Voltage Power Supply For Use On Board A Cubesat, Nicholas Weiser

Master's Theses

Since their conception in 1999, CubeSats have come and gone a long way. The first few that went into space were more of a “proof of concept,” and were more focused on sending simple data and photographs back to Earth. Since then, vast improvements have been made by over 40 universities and private firms, and now CubeSats are beginning to look towards interplanetary travel. These small satellites could provide a cost effective means of exploring the galaxy, using off the shelf components and piggy-backing on other launch vehicles with more expensive payloads. However, CubeSats are traditionally launched into Low Earth …

Improvements To A Bi-Directional Flyback Dc-Dc Converter For Battery System Of The Dc House Project, Michael Wu

Master's Theses

The DC House project relies primarily on renewable energy sources to provide DC power to the various loads of the house. However, not all renewable sources are capable of providing power at all times of the day. A back-up energy source in the form of a battery storage system must be available to meet the electrical needs of the house. A bi-directional flyback power converter was initially designed to allow a battery to charge from as well as discharge to the 48V bus line of the DC House. The design provided a 35W prototype to demonstrate the converter’s feasibility. Further …

Battery Management System, Michael Desando, Kyle Woody

Electrical Engineering

Problem Statement:

There have been recent reports of multi-million dollar companies having to recall entire projects due to their BMS’s malfunctioning or operating incorrectly. The purpose of this project is to analyze the future of batteries, the Lithium-Ion cell, and to exercise a BMS to better understand its capabilities and possible cases for errors. Lithium ion batteries are intolerant of overcharge and overdischarge. Abuse of this kind can result in high temperatures, venting of gases, fire, or explosion. Therefore battery management systems have been devised to prevent such abuse. Recent events such as fires on the Boeing Dreamliner and the …

Buck-Boost Dc-Dc Converter With Input Protection System For The Energy Harvesting From Exercise Machines Project, Byungjae David Yoo, Sheldon Tyler Kong Ming Chu

Electrical Engineering

Cal Poly’s Energy Harvesting from Exercise Machines (EHFEM) project comprises of multiple subprojects seeking to effectively create a sustainable energy source through harvesting electrical energy generated from physical exercise machines. This project designs and implements a Buck-Boost DC-DC converter using a LT3791-1 4-Switch Buck-Boost Controller, replacing the previous SEPIC design. The DC-DC converter must operate within limits set by the maximum input range of the LT3791-1 controller. An input protection system prevents inputs higher than rated values, which may adversely damage the Buck-Boost DC-DC converter. These inputs include overvoltage transients, average voltage, and current output by the Precor EFX 561i …

Portable Nano Hydro Generator For The Dc House Project, Caleb David Fink, Victor Olusoji Ojewole, Christopher Mapua Tan

Electrical Engineering

This Senior Project entails the design and testing processes of the Portable Nano Hydro Generator for the continuing DC House Project. No natural resources should go unused, especially in developing countries where they are found in abundance. Small streams in particular have potential to further Professor Taufik's DC House Project that will provide electricity to 1.6 billion people in the world without access to electricity upon completion. The goal of this project is to create a small portable generator that utilizes the discharge from small streams and convert it into useable electricity that could charge a car battery as an …

All Purpose Mobile Gps, James C. Smith, Matt Weege, Kevin Peters

Electrical Engineering

The aim of the All Purpose Mobile GPS (The System) is to create a GPS tracking device that can accurately record location and calculate velocity, distance traveled and elevation change even when the satellite signal is lost. This data can later overlay on existing internet-based maps illustrating a trip to oneself or others. The portable tracker consumes very little power achieving several days’ worth of power in a single charge. A solar cell provides a quick battery boost in a pinch. SD Card storage increases compatibility with computers and other forms of data transfer. Data processing, such as viewing the …

Design Improvement For The Smart Dc Wall Plug, Cory Yee, Haoyan Huang

Electrical Engineering

The DC smart wall plug is a subsystem within the Cal Poly DC House Project. The previous version faces challenges supplying DC voltage to meet household appliances’ nominal values. Specifically, it can only output the minimum required voltage for DC appliances to operate, resulting in unwanted power loss. In addition, the maximum output voltage is rated at 15V, which is insufficient to power most DC appliances. This design improvement project incorporates NFC technology as a solution to overcome the power loss and a new buck converter configuration to increase the output voltage range. Additionally, the new design introduces short-circuit and …

Integration Of Pv & Simulated Dc Sources For The Dc House, Arvind Ramesh, Kevin Gingrich, Scott Chau

Electrical Engineering

The DC House, an ever improving project, uses only pure DC power which most renewable energy sources generate, from solar to wind power. The DC House and this project expect a donation of photovoltaic modules to supply a constant source of DC power. At the moment, the DC House desperately needs power sources because not only does the house have various loads unaccounted for, but the distribution system to determine proper power flow needs a redesign. The project chose to account for these issues by implementing a solar panel onto the DC House and a power distribution module to have …

Evaluation Of Conservation Voltage Reduction As A Tool For Demand Side Management, Ali Dorrody

UNLV Theses, Dissertations, Professional Papers, and Capstones

To ensure stability of the power grid, electricity supply and demand must remain in balance in real time. Traditionally utilities, call upon peaking power plants to increase power generation to meet the peak demand during the afternoons of the hot summer months. Demand-side management (DSM), which includes energy efficiency and demand response (DR), works from the other side of the equation - instead of adding more generation to the system, it pays energy users to reduce consumption as it is cheaper and easier to procure than traditional generation. As a consequence, demand-side management allows utility customers to act as a …

Generation Of Bipolar Nanosecond Pulses, Sambasiva Rao Rajulapati

Electrical & Computer Engineering Theses & Dissertations

Bipolar pulse generation has been studied using transmission line technology, which was mainly used for monopolar pulse generation. In this thesis, low impedance, high current, nanosecond pulse generators were designed, constructed and tested. Five transmission lines were connected in parallel, so the impedance was 10 n. The transmission lines were switched by a spark gap switch operated in air. The closing of the switch creates a matched condition on one side of the transmission lines and a short circuit on the other side of the transmission lines. When the transmission lines are precharged, one of the two waves in opposite …

Position/Speed Sensorless Control For Permanent-Magnet Synchronous Machines, Yue Zhao

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Permanent-magnet synchronous machines (PMSMs) are widely used in industrial applications owing to their distinctive advantages, such as high efficiency, high power density, and wide constant power region. To achieve high-performance field oriented control, accurate rotor position information, which is usually measured by rotary encoders or resolvers, is indispensable. However, the use of these sensors increases the cost, size, weight, and wiring complexity and reduces the mechanical robustness and the reliability of the overall PMSM drive systems. The goal of the research for this dissertation was to develop a rotor position/speed sensorless control system with performance comparable to the sensor-based control …

Design And Implementation Of An X-Band Passive Rfid Tag, Praharshin Melaka Senadeera

Dissertations

This research presents a novel fully integrated energy harvester, matching network, multi-stage RF-DC rectifier, mode selector, RC oscillator, LC oscillator, and X-band power amplifier implemented in IBM 0.18-µm RF CMOS technology. We investigated different matching schemes, antennas, and rectifiers with focus on the interaction between building blocks. Currently the power amplifier gives the maximum output power of 5.23 dBm at 9.1GHz. The entire RFID tag circuit was designed to operate in low power consumption. Voltage sensor circuit which generates the enable signal was designed to operate in very low current. All the test blocks of the RFID tag were tested. …

Energy Optimization Of A Free-Piston Enhanced Hybrid Vehicle, Kenneth Jarod Jones

Dissertations

The world’s heavy dependence on vehicles which utilize hydrocarbon fuels as a primary power source has renewed the interest in electric and hybrid vehicles for industrial, commercial, and public use. The primary objective of this movement is centered on increased efficiency in energy usage for transportation. Hybrid vehicles which utilize an internal combustion engine as a linear generator, converting energy stored in hydrocarbon fuels into electrical power, could serve as a transitioning technology. The free-piston enhanced hybrid vehicle (FPHV) could potentially fill this role. The present work contains a theoretical and numerical approach to analyzing and optimizing the usage of …

Multifrequency Averaging In Power Electronic Systems, Fei Pan

Theses and Dissertations--Electrical and Computer Engineering

Power electronic systems have been widely used in the electrical power processing for applications with power levels ranging from less than one watt in battery-operated portable devices to more than megawatts in the converters, inverters and rectifiers of the utility power systems. These systems typically involve the passive elements such as inductors, capacitors, and resistors, the switching electronic components such as IGBTs, MOSFETS, and diodes, and other electronic circuits. Multifrequency averaging is one of the widely used modeling and simulation techniques today for the analysis and design of power electronic systems. This technique is capable of providing the average behavior …

A New Design Of Dc-Dc Converter For Capacitive Deionization Process, Zhiao Li

Theses and Dissertations--Electrical and Computer Engineering

The shortage of clean water has become a significant global problem, and capacitive deionization (CDI) is a technology that can be used to help relieve the problem. A Ćuk converter system that can recover energy from CDI cells is described. This converter transfers energy between two CDI cells when a cell is in its desorption period, allowing energy that would otherwise be lost to be recovered and improving overall system efficiency. In order to control the states of the MOSFET switches in the converter, a self boost charge pump is used. In this way, the microcontroller can control system duty …

Fea Estimation And Experimental Validation Of Solid Rotor And Magnet Eddy Current Loss In Single-Sided Axial Flux Permanent Magnet Machines, Xu Yang

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

The rotor and magnet loss in single-sided axial ux permanent magnet (AFPM) machines with non-overlapped windings is studied in this dissertation. Finite element analysis (FEA) estimations of the loss are carried out using both 2D and 3D modeling. The rotor and magnet losses are determined separately for stator slot passing and MMF space harmonics from currents in the stator. The segregation of loss between the solid rotor plate and the magnet is addressed. The eddy current loss reduction by magnet segmentation is discussed as well. Two prototype 24 slot/22 pole single-sided AFPMs, fabricated with both single layer (SL) and double …

Portable Nano-Hydro Power Generator For The Dc House Project, Andrew Aw, James Biggs

Electrical Engineering

This senior project report explains the construction and design of a small, portable water generator that converts kinetic energy flowing in small creeks to electrical energy as a renewable source of energy for the DC House. The DC House, in short, is a project to build a self-sustainable house for Third World countries that utilizes only DC electricity. The system consists of two converters and a charge controller for a 12V lead-acid battery. The first converter converts the hydro generator voltage output to 15 Volts for safe and proper charging of the lead-acid battery by the charge controller. The second …

Photovoltaic Tracker Optimization With Unique Fault Detection And Enhanced Combiner System, Caitlin Nicole Conway

Electrical & Computer Engineering Theses & Dissertations

Renewable energy resources are rapidly becoming extremely important as the world's energy consumption continues to rise. The most popular of these resources is solar energy and more specifically photovoltaic energy. Currently, solar modules on the market are still not highly efficient. In order to increase the productivity of solar energy systems, larger fixed-panel photovoltaic systems or tracking photovoltaic systems are utilized. The major disadvantage of larger photovoltaic systems is the increased space requirements. Therefore, tracking photovoltaic systems are the best alternative to achieve higher solar energy yields.

To date, the only method of monitoring tracking photovoltaic systems is with the …

Understanding Vehicular Traffic Behavior From Video: A Survey Of Unsupervised Approaches, Brendan Tran Morris, Mohan Manubhai Trivedi

Electrical & Computer Engineering Faculty Research

Recent emerging trends for automatic behavior analysis and understanding from infrastructure video are reviewed. Research has shifted from high-resolution estimation of vehicle state and instead, pushed machine learning approaches to extract meaningful patterns in aggregates in an unsupervised fashion. These patterns represent priors on observable motion, which can be utilized to describe a scene, answer behavior questions such as where is a vehicle going, how many vehicles are performing the same action, and to detect an abnormal event. The review focuses on two main methods for scene description, trajectory clustering and topic modeling. Example applications that utilize the behavioral modeling …

Solar Photovoltaic Water Pumping For Multiple Use Systems (Mus) In Nepal, Fintan Mcloughlin, Aidan Duffy, Michael Conlon

Conference Papers

This paper investigates the performance of five solar photovoltaic (PV) Multiple Use Systems (MUS) used for water pumping. The solar MUS’s provide water for drinking, cleaning and micro-irrigation for some of the poorest communities in Nepal. In the absence of data logging, the performance of each system is investigated based on a series of rules of thumb to determine the predicted, expected and estimated demand and supply of water to small rural communities. The systems are compared based on their technical and economic performance and how this relates to local environmental, physical and socioeconomic characteristics at each location.

Maximising Value Of Electrical Networks For Wave Energy Converter Arrays, Fergus Sharkey, Elva Bannon, Michael Conlon, Kevin Gaughan

Articles

Currently there are the beginnings of a commercial wave energy industry and the ultimate ambition will be to deploy Wave Energy Converters (WECs) in arrays, or wave farms, in a similar fashion to offshore wind. These arrays will require electrical networks to collect and export the generated electrical power to shore and onto the electrical grid. For large scale wind farms the inter-array and export electrical networks can represent more than 20% of the project’s capital expenditure. Submarine power cables account for a large proportion of this cost. The same is expected to be the same for WEC arrays.

This …

Impacts On The Electrical System Economics From Critical Design Factors Of Wave Energy Converters And Arrays, Fergus Sharkey, Michael Conlon, Kevin Gaughan

Conference papers

It is expected that ultimately, like offshore wind farms, electrical systems will make up to a quarter of the overall Capex of wave farms. This is a significant element of cost and consideration must be taken in the design of both individual wave energy converters (WECs) and arrays of WECs to ensure that these costs can be minimised. In a worst case scenario design decisions could increase the cost of the electrical system by several orders and ultimately make the technology uncompetitive.

This paper outlines the impacts on the cost of the electrical system arising from design factors of WECs …

Resource-Induced Voltage Flicker For Wave Energy Converters – Assessment Tools, Fergus Sharkey, Joe Macenri, Elva Bannon, Michael Conlon, Kevin Gaughan

Articles

For wave energy converters, the input resource has a typical period of 5–20 s depending on the site location and dominant seastates. Wave energy converters generally produce mechanical power twice per wave cycle and therefore depending on the storage available, the electrical power output has half the period of the input resource. These regular power changes induce a voltage change at the point of connection (POC) which is proportional to the amplitude of the power change and at the same frequency. Therefore the coupling of the input resource to the output power of a wave energy converter will cause voltage …