Electrical and Electronics Commons^™

Grid-Connected Photovoltaic Systems Based On Nonlinear Control., Pablo R. Rivera

Electronic Theses and Dissertations

Nowadays, due to the high-scale penetration of photovoltaic systems, reliable and efficient grid-connected photovoltaic (PV) systems utilizing the advances of power electronics and control system technology are desirable. Thus, single-stage grid-connected photovoltaic systems, have gained attention, especially in low voltage applications. However, PV systems exhibit nonlinear behavior that could negatively affect the performance of the system if they are not adequately compensated for. In this dissertation, using the general structure for the synchronous dq0 frame, a single-stage three-phase grid-connected photovoltaic system, and a single-stage single-phase grid-connected PV system, both with a nonlinear control strategy, are developed to track the maximum …

Gating Methods For High-Voltage Silicon Carbide Power Mosfets, Audrey Dearien

Graduate Theses and Dissertations

The objective of this thesis is to assess the challenges associated with driving Silicon Carbide (SiC) power devices, and to compare the potential gate drive methods for these devices which address those challenges. SiC power devices present many benefits that make them suitable for next generation automotive, power utility grid, and energy management applications. High efficiency, increased power density, and reliability at high-temperatures are some of the main benefits of SiC technology. However, the many challenges associated with these devices have prevented their adoption into industry applications. The argument is made in this thesis that the gate driver is a …

Accurate Location Of Evolving Faults On Transmission Lines Using Sparse Wide Area Measurements, Xiangqing Jiao, Yuan Liao

Electrical and Computer Engineering Faculty Publications

In electric power systems, not all fault conditions remain unchanged during faults. An evolving fault has one characteristic initially and changes to a different condition subsequently. Locating evolving faults is challenging due to the change in fault type shortly after the fault initiation. This paper presents a new approach for estimating the locations of evolving faults on transmission lines. By using sparse wide area voltage measurements, this method is able to accurately locate evolving faults without requiring measurements from either end of the faulted line. There is no need to detect whether a fault is an evolving fault or not. …

Optimal Operation Of Integrated Microgrids, Abdullah Albaker

Electronic Theses and Dissertations

Microgrids' deployments are increasing and projected to increase even more in future due to the significant advantages that are provided by this technology for end-use customers. However, microgrids can be connected to each other to create integrated microgrids system, which can further promote the anticipated and desired benefits. An integrated operation of microgrids can potentially improve the local power system reliability and resilience, increase the individual microgrids' economic benefits, and promote further utilization of renewable energy resources. Integrating microgrids, to achieve a microgrid network or cluster, is expected be an essential application towards smarter power grids and a key operational …

Control Of Gas Metal Arc Welding Using Process Sensing And Laser Arc Stabilization For Additive Manufacturing, Dale Brush

Graduate Theses & Non-Theses

The goal of the present research was to bridge the gap between powder-based and wire-based additive manufacturing (AM) processes using gas metal arc welding (GMAW). Powder-based AM processes typically can produce components with high geometric resolution (small features), but at low deposition rates. Wire-based AM processes typically can produce components with low geometric resolution, but at high deposition rates. AM with GMAW is a wire-based AM process in the wire arc additive manufacturing (WAAM) category of AM. To bridge the gap between powder-based and wire-based AM processes, GMAW’s deposition rate has to be reduced, allowing small features to be built. …

Electrowetting Using A Microfluidic Kelvin Water Dropper, Elias Yazdanshenas, Qiang Tang, Xiaoyu Zhang

Mechanical & Aerospace Engineering Faculty Publications

The Kelvin water dropper is an electrostatic generator that can generate high voltage electricity through water dripping. A conventional Kelvin water dropper converts the gravitational potential energy of water into electricity. Due to its low current output, Kelvin water droppers can only be used in limited cases that demand high voltage. In the present study, microfluidic Kelvin water droppers (MKWDs) were built in house to demonstrate a low-cost but accurately controlled miniature device for high voltage generation. The performance of the MKWDs was characterized using different channel diameters and flow rates. The best performed MKWD was then used to conduct …

Contributions To Hybrid Power Systems Incorporating Renewables For Desalination Systems, Nasser Alawhali

Theses and Dissertations--Electrical and Computer Engineering

Renewable energy is one of the most reliable resource that can be used to generate the electricity. It is expected to be the most highly used resource for electricity generation in many countries in the world in the next few decades. Renewable energy resources can be used in several purposes. It can be used for electricity generation, water desalination and mining. Using renewable resources to desalinate the water has several advantages such as reduce the emission, save money and improve the public health. The research described in the thesis focuses on the analysis of using the renewable resources such as …

Ball Oscillating Bouncer, Eric Blok, Daniel Altemese, Ryan Nowacki, Maram Qurban

Williams Honors College, Honors Research Projects

The purpose of this report is to document the need, objectives, marketing and engineering requirements, as well as validate the design of an autonomous control device capable of continuously bouncing a table tennis ball on a paddle. This includes the design of a self correcting system using lightweight materials, and as few sensors and components as possible to achieve a compact, portable design. To accomplish this, the system is designed to react to a ball falling from as short a distance as 10 centimeters above the paddle, meaning all sensor processing, control processing, and motor drives should be able to …

Stability Analysis And Design Of A Tracking Filter For Variable Frequency Applications, Pranav Aramane

Theses and Dissertations--Electrical and Computer Engineering

The work presented in this thesis is a frequency adaptive tracking filter that can be used in exact tracking of power frequencies and rejection of unwanted harmonics introduced during power disturbances. The power synchronization process includes power converters and other equipment that have many non-linear components that introduce unwanted harmonics. This new design is motivated by the requirement of a filter that can filter all the harmonics and exactly track a rapidly varying fundamental frequency with little time delay and phase error. This thesis analyzes the proposed filter mathematically based on Lyapunov theory and simulations are presented to show the …

Advanced Synchronous Machine Modeling, Yuqi Zhang

Theses and Dissertations--Electrical and Computer Engineering

The synchronous machine is one of the critical components of electric power systems. Modeling of synchronous machines is essential for power systems analyses. Electric machines are often interfaced with power electronic components. This work presents an advanced synchronous machine modeling, which emphasis on the modeling and simulation of systems that contain a mixture of synchronous machines and power electronic components. Such systems can be found in electric drive systems, dc power systems, renewable energy, and conventional synchronous machine excitation. Numerous models and formulations have been used to study synchronous machines in different applications. Herein, a unified derivation of the various …

Designing And Testing 3-D Printed Wafer-Box With Embedded Pzt Sensors To Identify The Shape Effect On Energy Harvesting, Ahmad Jami Safayet

College of Graduate Studies: Theses & Dissertations

Piezoelectric energy has been recently paid attention in the field of alternative energy. Day by day the traditional energy sources including Coal tar and oils are becoming scarce. People are heading to an alternative energy source to meet the future energy demand. Piezoelectric energy is one of the competitive energy sources compared to the conventional renewable energy sources including solar, wind, and geothermal power and so on. This energy production method bears enormous research potential because it can be used as the roadway for a new method of power generation. This research project aimed to identify which shaped wafer-box produced …

A Quantification Analysis On Potential Use Of Recuperated Regenerative Braking Energy From Nyct Subways Into Charging Electric Buses, Ahmed S. Rahman

Dissertations and Theses

The New York Metropolitan Transportation Authority (MTA) is one of the biggest consumers of electricity in east coast of the United States. According to a report published by Dayton T. Brown in 2013, MTA consumes approximately 2150 GWh electrical energy per year for traction power, where the New York City Transit (NYCT) alone is a consumer of about 80% of the total annual MTA energy consumption. This continuous high demand for electricity from a single organization opens research opportunities to search for alternative ways to reduce the needs. NYCT Subways has an existing total rolling stock of 6,418 train cars …

A Case Study On Grid Impacts Of Electric Vehicles On New York City Power Grid, Amir Abbas Rizvi

Dissertations and Theses

The U.S. electric power industry is anticipating a huge increase in electricity demand in the future due to reformation of the transportation industry. In this work, we focus on electric cars and their impact on the transportation industry as well as the electric grid. The increase in number of electric cars over the years and their growing number indicates that in the future, transportation means are going to largely depend upon electricity to achieve cost and environmental benefits. In other words, in future, the transportation will be impacting the electric grid and vice versa.

The surge in electric vehicles on …

Modeling, Designing And Analysis Of A Standalone Pv Dc Microgrid System, Sharaf Sumaiya

College of Graduate Studies: Theses & Dissertations

The increasing concern about global warming, the upsurge of oil prices, and pollution of petroleum energy has led scientists to search for cost-effective energy sources, for example, photovoltaics. Recently DC microgrids have also drawn more consideration because of the expanding use of direct current (DC) energy sources, energy storages and loads in power systems. First, as a groundwork, the 1D organic solar cell has been investigated that leads to design 3D organic solar cell. Then design and analysis of a standalone solar PV system with dc microgrid has been proposed to supply power for both DC and AC loads. The …

Core And Uncore Joint Frequency Scaling Strategy, Vaibhav Sundriyal, Masha Sosonkina, Bryce Westheimer, Mark Gordon

Electrical & Computer Engineering Faculty Publications

Energy-proportional computing is one of the foremost constraints in the design of next generation exascale systems. These systems must have a very high FLOP-per-watt ratio to be sustainable, which requires tremendous improvements in power efficiency for modern computing systems. This paper focuses on the processor—as still the biggest contributor to the power usage—by considering both its core and uncore power subsystems. The uncore describes those processor functions that are not handled by the core, such as L3 cache and on-chip interconnect, and contributes significantly to the total system power. The uncore frequency scaling (UFS) capability has been available to the …

Testing Of Recursive And Non-Recursive Algorithms For Real-Time Phasor And Frequency Estimations In Power Systems, Dhruv Sharma

Dissertations, Master's Theses and Master's Reports

Steady-state performance of various recursive and non-recursive algorithms are tested in this report according to the test signals given in the IEEE Standard C37.118.1-2011. Phase magnitude and phase angle of the power grid signals have been estimated using Discrete Fourier Transform (non-recursive), Discrete Fourier Transform (recursive), Least Square, and Wavelet Transform Algorithms. Frequency estimation is performed using Discrete Fourier Transform, Weighted Least Square, and Zero Crossing methods. These algorithms are evaluated in LabView software and tested by generating test signals in a Simulink model. Furthermore, Total Vector Error (TVE) is calculated using dynamic test signals as per the IEEE Standard …

Cyber-Based Contingency Analysis And Insurance Implications Of Power Grid, Zhiyuan Yang

Dissertations, Master's Theses and Master's Reports

Cybersecurity for power communication infrastructure is a serious subject that has been discussed for a decade since the first North American Electric Reliability Corporation (NERC) critical infrastructure protection (CIP) initiative in 2006. Its credibility on plausibility has been evidenced by attack events in the recent past. Although this is a "very high impact, rare probability" event, the establishment of quantitative measures would help asset owners in making a series of investment decisions. First, this dissertation tackles attackers' strategies based on the current communication architecture between remote IP-based (unmanned) power substations and energy control centers. Hypothetically, the identification of intrusion paths …

Energy Storage Control And Requirements For Inverter-Based Microgrids, Mehrzad Mohammadi Bijaieh

Dissertations, Master's Theses and Master's Reports

The intermittent nature of distributed renewable sources such as wind or solar requires integration of energy storage systems. In this dissertation a distributed form of the Hamiltonian Surface Shaping and Power Flow Control (HSSPFC) method is used to determine the energy storage requirements of three-phase inverter-based microgrids. The overall control is appropriate to be integrated into a hierarchical control system. As the primary control, a novel dq droop control sets the local references and is supported by a level-zero Hamiltonian controller which includes energy storage feed-forward and feedback, and an inverter feed-forward controls. Here, the energy storage element performs as …

Coupling Radio Frequency Energy Via The Embedded Rebar Cage In A Reinforced Concrete Structure For The Purpose Of Concrete Degradation Sensing, Ryan Campiz

UNF Graduate Theses and Dissertations

This study focuses on utilizing an energy harvesting system in which a dedicated Radio Frequency (RF) power source transmits RF power via rebar in a reinforced concrete column. The RF power is received and decoupled by a receiver, and is then rectified, boosted, and stored as electrical energy in a supercapacitor, later to be used to make measurements, process data, and communicate to the source via rebar. Two design attempts are presented in this study: (a) one uses single line conduction at 2.4 GHz for RF power transfer; (b) the other uses a more conventional two-line conduction at 8.0 kHz …

Parameter Estimation Technique For Models In Pss/E Using Real-Time Data And Automation, Malavika Vasudevan Menon

LSU New Orleans Theses and Dissertations

The purpose of this thesis is to use automation to create appropriate models in PSS/E with the data from Hardware-in-Loop real-time simulations. With the increase in technology of power electronics, the use of High Voltage Direct Current Technology and Flexible Alternating Current Transmission System devices in the electrical power system have increased tremendously. Static Var Compensators are widely used and it is important to have accurate and reliable models for studies relating to power systems planning and interaction. An automation method is proposed to find the parameters of an SVC model in PSS/E with the data from the Hardware-in- loop …

Harmonics Elimination In Three Phase Cascade H-Bridge Multilevel Inverter Using Virtual Stage Pwm, Amro Quedan

Durham School of Architectural Engineering and Construction: Dissertations, Theses, and Student Research

The multilevel inverters are one of the great solutions that are proposed to satisfy the demand for high-power application and the significant integration of renewable energy. The conversion process from DC to AC must be done at high efficiency to decrease the energy loss and to ensure the electric grid power quality. The Total Harmonic Distortion (THD) is the most important feature that indicates the efficiency of the conversion process. In this research, due to the advantages of the cascade H-bridge inverter over other topologies, it has been used with the virtual stage PWM technique to investigate two different methods …

Flexible Custom Electric Skateboard, Caleb Adam Kelsay

Electrical Engineering

At Cal Poly traveling long distances only accessible by foot such as across campus or from the car park to class can be tiring and time-consuming. While not physically demanding, the trek consumes time in our tight college life schedule. To improve our time efficiency this project provides a relatively lightweight, powered solution to quickly and effectively travel long distances while maintaining full control and safety even on hills, a current limitation of traditional skateboards.

This electric skateboard includes the battery capacity to travel all around campus on a single charge with a compact and flexible skateboard design that provides …

Energy Shaping Control For Stabilization Of Interconnected Voltage Source Converters In Weakly-Connected Ac Microgrid Systems, Nadia Lenora Carmita Smith

Graduate Theses and Dissertations

With the ubiquitous installations of renewable energy resources such as solar and wind, for decentralized power applications across the United States, microgrids are being viewed as an avenue for achieving this goal. Various independent system operators and regional transmission operators such as Southwest Power Pool (SPP), Midcontinent System Operator (MISO), PJM Interconnection and Electric Reliability Council of Texas (ERCOT) manage the transmission and generation systems that host the distributed energy resources (DERs). Voltage source converters typically interconnect the DERs to the utility system and used in High voltage dc (HVDC) systems for transmitting power throughout the United States. A microgrid …

Dc-To-Dc Buck Converter, Kyle Christopher Roman

Electrical Engineering

The growth of sustainable energy requires many components to work in harmony creating one efficient and effective system. Sustainable energy generation that produces a DC current varying in voltage requires a subsystem to convert voltage to a practical and usable value. The DC to DC Buck converter converts high DC solar generated voltage to a 12V output. This Modular -Level power electronic (MLPE) device performs as a solar charge controller for small lithium ion batteries. Fluctuating voltage levels generated by Photovoltaic cells makes the solar controller a critical part of the solar system. Regulating the DC voltage allows safe and …

Power Interface Design And System Stability Analysis For 400 V Dc-Powered Data Centers, Yuzhi Zhang

Graduate Theses and Dissertations

The demands of high performance cloud computation and internet services have increased in recent decades. These demands have driven the expansion of existing data centers and the construction of new data centers. The high costs of data center downtime are pushing designers to provide high reliability power supplies. Thus, there are significant research questions and challenges to design efficient and environmentally friendly data centers with address increasing energy prices and distributed energy developments.

This dissertation work aims to study and investigate the suitable technologies of power interface and system level configuration for high efficiency and reliable data centers.

A 400 …

Hardware Based Testing Of Communication Based Control For Dc Microgrid, Mahmoud Saleh, Yusef Esa, Ahmed Mohamed

Publications and Research

This paper further describes our work presented in Industry Application Society 2016 Conference, with more details related to the control and operation of the microgrid. The DC microgrid facility was custom designed and implemented at CCNY with minimal off-the-shelf components to enable flexibility and reconfiguration capability. The design steps, requirements, and experimental results of the developed testbed were discussed. As a case study, a central controller for energy management algorithm was developed and tested under several operational scenarios. The experimental results verify the applicability of the developed testbed for validating DC microgrid controllers.

Quantitative Analysis Of Regenerative Energy In Electric Rail Traction Systems, Mahmoud Saleh, Oindrilla Dutta, Yusef Esa, Ahmed Mohamed

Publications and Research

This paper aims at determining the influential factors affecting regenerative braking energy in DC rail transit systems. This has been achieved by quantitatively evaluating the dependence of regenerative energy on various parameters, such as vehicle dynamics, train scheduling, ground inclination and efficiency of the electrical devices. The recuperated power and energy have been presented by a mathematical model, comprising of a set of empirical forms, which allows for thorough analysis. A detailed simulation model of a typical DC-traction system has been developed to validate the developed empirical forms. The results verified the validity of the proposed mathematical model, and demonstrated …

Optimal Microgrids Placement In Electric Distribution Systems Using Complex Network Framework, Mahmoud Saleh, Yusef Esa, Nwabueze Onuorah, Ahmed Mohamed

Publications and Research

This paper provides a new approach to find the optimal location for Microgrids (MGs) in electric distribution systems using complex network analysis. An optimal location in this paper refers to a location that would result in increased grid resilience, reduced power losses, less line loading, higher voltage stability and secured supply to critical loads during power outage. The criteria used to find the optimal placement of MGs were based on the centrality analysis adopted from complex network theory, the center of mass concept used in physics, and the controlled delivery grid (CDG) concept. An IEEE 30-bus system was used as …

Energy Management Algorithm For Resilient Controlled Delivery Grids, Mahmoud Saleh, Yusef Esa, Ahmed Mohamed, Haim Grebel, Roberto Rojas-Cessa

Publications and Research

Resilience of the power grid is most challenged at power blackouts since the issues that led to it may not be fully resolved by the time the power is back. In this paper, a Real-Time Energy Management Algorithm (RTEMA) has been developed to increase the resilience of power systems based on the controlled delivery grid (CDG) concept. In a CDG, loads communicate with a central controller, periodically sending requests for power. The central controller runs an algorithm, based on which it may decide whether to grant the requested energy fully or partially. Therefore, the CDG limits loads discretionary access to …

Design Of Dc-Link Vscf Ac Electrical Power System For The Embraer 190/195 Aircraft, Eduardo Francis Carvalho Freitas, Nihad E. Daidzic

Journal of Aviation Technology and Engineering

A proposed novel DC-Link VSCF AC-DC-AC electrical power system converter for Embraer 190/195 transport category airplane is presented. The proposed converter could replace the existing conventional system based on the CSCF IDGs. Several contemporary production airplanes already have VSCF as a major or backup source of electrical power. Problems existed with the older VSCF systems in the past; however, the switched power electronics and digital controllers have matured and can be now, in our opinion, safely integrated and replace existing constant-speed hydraulic transmissions powering CSCF AC generators. IGBT power transistors for medium-level power conversion and relatively fast efficient switching are …