Electrical and Electronics Commons^™

Optimal Power Flow Control Of Networked Dc Microgrids, Eddy H. Trinklein

Dissertations, Master's Theses and Master's Reports

The US military is moving toward the electrification of many weapon systems and platforms. Advanced weapon systems such as high energy radar, electro-magnetic kinetic weapons and directed energy pose significant integration challenges due to their pulsed power electrical load profile. Additionally, the weapons platforms, including ships, aircraft, and vehicles can be studied as a mobile microgrids with multiple generation sources, loads, and energy storage. There is also a desire to extend the mission profile and capabilities of these systems. Common goals are to increase fuel efficiency, maintaining system stability, and reduce energy storage size as typically required to enable pulsed …

Autonomous Combat Robot, Andrew J. Szabo Ii, Chris Heldman, Tristin Weber, Tanya Tebcherani, Holden Leblanc, Fabian Ardeljan

Williams Honors College, Honors Research Projects

This honors project will also serve as an engineering senior design project.

The objective is to design and build the software and electrical systems for a 60 lb weight class combat robot that will function autonomously and outperform manually driven robots during competition.

While running autonomously, the robot will use LiDAR sensors to detect and attack opponent robots. This robot will also be able to be remote controlled in manual mode. This will mitigate the risk in case the autonomy or sensors fail. LED lights on the robot will indicate whether it is in autonomous or manual mode. The system …

Cycle Assist, Tyler Matthews

Williams Honors College, Honors Research Projects

The senior engineering design project presented in the paper that succeeds this, outlines the steps taken to design and implement an electronic bicycle that is able to keep a user’s heart-rate in a selected “intensity zone” though the use of an electronic motor and custom control circuitry. My portion of this project was to allow for safe and consistent power delivery to the rest of the electronics. That is to say, I built a battery pack and battery management system (BMS) to safely supply sufficient power to the rest of the electronics that were required for this project. In order …

Electric Load Forecasting Using Long Short-Term Memory Algorithm, Tianshu Yang

Theses and Dissertations

Abstract

Power system load forecasting refers to the study or uses a mathematical method to process

past and future loads systematically, taking into account important system operating

characteristics, capacity expansion decisions, natural conditions, and social impacts, to

meet specific accuracy requirements. Dependence of this, determine the load value at a

specific moment in the future. Improving the level of load forecasting technology is

conducive to the planned power management, which is conducive to rationally arranging

the grid operation mode and unit maintenance plan, and is conducive to formulating

reasonable power supply construction plans and facilitating power improvement, and

improve the …

Design And Implementation Of Overcurrent Protection Relays Test Bench, Khalid Daud Khattak

Graduate Theses, Dissertations, and Problem Reports (ETD)

The electrical power simulator in Engineering Sciences Building (ESB) at WVU was dismantled in July 2018. The simulator was used as a teaching tool for EE students to conduct lab experiments. The power simulator employed electromechanical and microprocessor protection relays, manual isolation and industrial circuit breakers, switches, variable autotransformer (VARIAC), voltmeters and ammeters. During the dismantling, a lot of equipment was retrieved for future possible use. This led to the idea of designing and implementing a simple circuit on a test bench that can be used as a lab equipment to demonstrate the operation of overcurrent protection relays. It was …

Mathematical Programming Approach For The Design Of Satellite Power Systems, Allen Flath Iii

Theses and Dissertations--Electrical and Computer Engineering

Satellite power systems can be understood as islanded dc microgrids supplied by specialized and coordinated solar cell arrays augmented by electrochemical battery systems to handle high-power loads and periods of eclipse. The periodic availability of power, the limited capacity of batteries, and the dependence of all mission service on power consumption create a unique situation in which temporal power and energy scarcity exist. A multi-period model of an orbital satellite power system’s performance over a mission’s duration can be constructed. A modular power system architecture is used to characterize the system’s constraints. Using mathematical programming, an optimization problem can be …

Curricular Optimization: Solving For The Optimal Student Success Pathway, William G. Thompson-Arjona

Theses and Dissertations--Electrical and Computer Engineering

Considering the significant investment of higher education made by students and their families, graduating in a timely manner is of the utmost importance. Delay attributed to drop out or the retaking of a course adds cost and negatively affects a student’s academic progression. Considering this, it becomes paramount for institutions to focus on student success in relation to term scheduling.

Often overlooked, complexity of a course schedule may be one of the most important factors in whether or not a student successfully completes his or her degree. More often than not students entering an institution as a first time full …

Optimum Design Of Axial Flux Pm Machines Based On Electromagnetic 3d Fea, Narges Taran

Theses and Dissertations--Electrical and Computer Engineering

Axial flux permanent magnet (AFPM) machines have recently attracted significant attention due to several reasons, such as their specific form factor, potentially higher torque density and lower losses, feasibility of increasing the number of poles, and facilitating innovative machine structures for emerging applications. One such machine design, which has promising, high efficiency particularly at higher speeds, is of the coreless AFPM type and has been studied in the dissertation together with more conventional AFPM topologies that employ a ferromagnetic core.

A challenge in designing coreless AFPM machines is estimating the eddy current losses. This work proposes a new hybrid analytical …

Ict-Enabled Control And Energy Management Of Community Microgrids For Resilient Smart Grid Operation, Mahmoud Saleh

Dissertations and Theses

Our research has focused on developing novel controllers and algorithms to enhance the resilience of the power grid and increase its readiness level against major disturbances.

The U.S. power grid currently encounters two main challenges: (1) the massive and extended blackouts caused by natural disasters, such as hurricane Sandy. These blackouts have raised a national call to explore innovative approaches for enhanced grid resiliency. Scrutinizing how previous blackouts initiated and propagated throughout the power grid, the major reasons are lack of situational awareness, lack of real-time monitoring and control, underdeveloped controllers at both the transmission and distribution levels, and lack …

A Review Of Co2 Emission Reductions Due To Wind Turbines Using Energy Benchmarks: A Focus On The Irish Electrical Energy Market, Tony Kealy

Articles

The installed capacity of wind turbines in Ireland increased from a value of 2,250 MW in 2014 to 3,318 MW in 2017, a 43% increase in the four years, supported through climate mitigation policies. The main aim of this study is to determine if the increase in wind turbine installed capacity is impacting on efforts to reduce CO2 emissions. The study utilises a review methodology. The findings show that the steady rise in wind turbine installed capacity year-on-year is not reflected in the Irish CO2 g/kWh energy benchmark. The benchmark value was 457 g CO2/kWh in 2014 and 437 g …

Series Compensation To Increase Power Flow: A Case Study On The Irish Transmission System, Aidan Heffernan, Jane Courtney

Conference papers

Ireland presents an interesting case study for transmission network strengthening. The majority of load in the country is located at the nation's capital, Dublin, in the East, while most of the new conventional generation and renewable generation are found in the South-West. Power is transferred between the two via a 400 kV network. This leads to large cross- country power flows. This power distribution disparity is due to increase. A large thermal generating station which is connected to the 400 kV system in the West, will close by 2025. This generation will be replaced partially with wind generation in the …

Performance Evaluation Of Communication Technologies And Network Structure For Smart Grid Applications, Desong Bian, Murat Kuzlu, Manisa Pipattanasomporn, Saifur Rahman, Di Shi

Engineering Technology Faculty Publications

The design of an effective and reliable communication network supporting smart grid applications requires the selection of appropriate communication technologies and protocols. The objective of this study is to study and quantify the capabilities of an advanced metring infrastructure (AMI) to support the simultaneous operation of major smart grid functions. These include smart metring, price-induced controls, distribution automation, demand response, and electric vehicle charging/discharging applications in terms of throughput and latency. OPNET is used to simulate the performance of selected communication technologies and protocols. Research findings indicate that smart grid applications can operate simultaneously by piggybacking on an existing AMI …

Development Of A Rapid Fatigue Life Testing Method For Reliability Assessment Of Flip-Chip Solder Interconnects, Cody Jackson Marbut

Graduate Theses and Dissertations

The underlying physics of failure are critical in assessing the long term reliability of power packages in their intended field applications, yet traditional reliability determination methods are largely inadequate when considering thermomechanical failures. With current reliability determination methods, long test durations, high costs, and a conglomerate of concurrent reliability degrading threat factors make effective understanding of device reliability difficult and expensive. In this work, an alternative reliability testing apparatus and associated protocol was developed to address these concerns; targeting rapid testing times with minimal cost while preserving fatigue life prediction accuracy. Two test stands were fabricated to evaluate device reliability …

Dc-Dc 4-Switch Buck-Boost Converter For Energy Harvesting From Elliptical Machines, Alexander C. Samietz, Gustavo Guzman

Electrical Engineering

The senior project report documents the process of replacing the network of resistors inside an elliptical machine with a DC-DC buck-boost converter. The buck-boost DC-DC converter accepts a wide input range of 5-60 Volts, with an output of 36 Volts for the most efficient use of the already available microinverter. The microinverter reclaims the lost energy and safely distributes it back to the electrical grid. The addition of this project reduces heat emissions from wasted energy and shrinks the carbon footprint of its users.

Effect Of Wireless Communication Delay On Dc Microgrids Performance, Mahmoud Saleh, Yusef Esa, Ahmed Mohamed

Publications and Research

This paper investigates the effect of wireless communication technologies latency on the converters and the bus voltage of centrally communication based controlled DC microgrids (MGs) during islanding. A DC microgrid with its communication based control scheme was modeled to show the impact of latency. Simulation results show that the impact may be severe depending on the design, and the operational condition of the microgrid before latency occurs.

Improving A Transient Stability Control Scheme With Wide-Area Synchrophasors And The Microwecc, A Reduced-Order Model Of The Western Interconnect, Robin Hallett

Graduate Theses & Non-Theses

This thesis is composed of two research projects. The first project investigated the feasibility of improving a generator tripping control scheme using wide-area synchrophasors and the second project focused on building a reduced-order model of the western North American power system (wNAPS) for use in a real-time digital simulator.

Transient stability is a major reliability issue for power systems. Radially-connected power plants are especially prone to transient stability problems. An example of this is the fourgenerator Colstrip power plant located in southeast Montana, USA. The Colstrip generators are protected by a tripping control system called the Acceleration Trend Relay (ATR) …

Impact Of Communication Latency On The Bus Voltage Of Centrally Controlled Dc Microgrid During Islanding, Mahmoud Saleh, Yusef Esa, Ahmed Mohamed

Publications and Research

Maintaining a sustainable and reliable source of energy to supply critical loads within a renewable energy based microgrid (MG) during blackouts is directly related to its bus voltage variations. For example, voltage variation might trigger protection devices and disconnect DERs within the MG. Centrally controlled MGs (CCMGs) type is dependent on communication. Therefore, it is very important to analyze the impact of communication networks performance degradation, such as latency, on the bus voltage of CCMGs. This paper investigates the effect of wireless communication technologies latency on the bus voltage and performance of centralized DC MGs. Two mathematical models were developed …

Hybrid Perovskite Characterization And Device Applications., Kasun Fernando

Electronic Theses and Dissertations

Hybrid perovskites are a group of materials that has shown a great impact in the field of scientific research in the past decade due to the efficiency gain within a short period of time. Hot casting is one technique that has been producing high efficient and stable solar cells. Electrical transportation of lateral device structure by such film is explored to understand basic properties and predict possible device applications using it. Under dark, memristive ability of the film was explored using various experiments. Unique uni-polar memristor ability was observed. Using the experimental results, a model is hypothesized using the concepts …

Investigation Of The Skin Effect In Alternating Currents, Matthew Liang

The International Student Science Fair 2018

My research is on the investigation of the skin effect in alternating currents. The skin effect is when an alternating current tends to flow on the surface of the conductor, such that the current density is highest near the surface, and decreases with greater depths in the conductor. This is due to the alternating current inducing changing magnetic fields, which in turn induces currents that oppose the original flow of current, resisting the current flowing through the centre the most. This reduces the effective cross-sectional area of the conductor and increases the resistance, causing increased power losses. This effect becomes …

Low Voltage Ride Through Enhancement For Wind Turbines Equipped With Dfig Under Symmetrical Grid Faults, Francis Mwasilu

Tanzania Journal of Engineering and Technology (TJET)

In modern power systems with significant penetration of wind-turbines (WTs), improvement of low voltage ride through (LVRT) capability of WTs equipped with doubly-fed induction generators (DFIGs) is an important issue. Thus, this paper proposes a low voltage ride through (LVRT) strategy, which comprise of a capacitor connected in series with an inductor both connected in parallel to a resistor. The configuration is then connected to a small series resistor via a pair of antiparallel-Thyristors. The circuit and its switching control scheme of the proposed LVRT circuit are designed to: minimize the transition times, maintain the RSC connection to the rotor-windings, …

Investigation Of The Skin Effect In Alternating Currents, Matthew Liang

The International Student Science Fair 2018

My research is on the investigation of the skin effect in alternating currents. My project is broken down into 4 sub-aims. The first aim would be, to be able to mathematically model the distribution of current in the radius of the wire, which consists of the applications of the Maxwell equation and solving zeroth order differential Bessel equations of the first kind. The next aim would be to computationally plot out the desired current readings as the depth of the wire increases from the surface, using the Matlab software. The third aim that I have would be conducting an experiment, …

Energy Conversion System For Travelers (Ecost), Thipok Bovornratanaraks

The International Student Science Fair 2018

We have innovated “The Energy Conversion System for Travelers” or the ECoST. With the fact that most travelers have wheeled cabin-bags, whilst walking, the wheels will rotate so why don’t we harvest electricity from this kinetic energy? We thus install our innovation, the ECoST, to the bag to generate electricity from the spinning wheels. The electricity is then kept in the storage unit and ready to charge your empty battery devices in an emergency case via a USB port. To make life easy, our ECoST was designed to replicate the power bank charging method; therefore, we can charge …

Electric Upgrades - Supercapacitor Electric Bicycle, John Chen, Wilson Fletcher, Spencer Esparza

Electrical Engineering

Supercapacitors provide high current capabilities compared to conventional lithium-ion batteries, allowing for fast charging and discharging of electrical energy. This project seeks to test the benefits of supercapacitors in an electric bicycle unit in order to gain higher regenerative energy. The main components of the bicycle are its regenerative motor, supercapacitor array, and motor controller. Developing the project will provide data on the feasibility of using alternative battery storage and charging.

Analog Sorting Using Pulse Width Modulation, Riley C. Olson

Computer Engineering

As time goes on, computers become more and more powerful. However, as processing time becomes less of a limiting factor for computing tasks, power consumption takes its place for many tasks. This paper proposes and tests a new method for sorting analog signals. This new sorting method converts analog signals into Pulse Width Modulated(PWM) signals of varying duty cycle , which are then sorted by a simple network of combinational logic, and then converted to a normal binary representation. In order to implement this new method, multiple circuits had to be designed and and tested to ensure their functionality and …

A Multiphase Modified Boost Converter With Reduced Input Current Ripple: Combined Capacitors, Omri Nissan

Master's Theses

The delivery of high power and smaller footprints through a non-isolated topology demands for the use of multiphase topology in DC-DC converters. Multiphase reduces the ripple observed on both the input and output waveforms; however, it may not be enough to connect to sensitive power sources such as renewable energy sources. A single-phase modified boost converter demonstrates the ability to acquire very minimal input current ripple by addition of passive components. The expansion to multiphase topology is the next logical step for higher power application while furthering the low input current ripple benefit. In this thesis, the multiphase modified boost …

The Modified-Multiphase Boost Converter: Combined Inductors And Capacitors Topology, Zachary L. Eldredge

Master's Theses

In this work, a modified boost converter design has been implemented in a multiphase configuration with a condensed topology. The modified aspect of the design has already been proven to drastically reduce input current ripple by about 40% in a single-phase implementation. By placing two modified boost converters in parallel with interleaving main switches (multiphase), the input inductors and modified capacitors of the modified topology can be reduced to just one of each, lowering the number of components, size, and cost. Additionally, multiphase DC/DC converters lower input/output voltage and current ripples while delivering more power compared to single-phase converters. By …

Performance Evaluation Of Energy-Autonomous Sensors Using Power-Harvesting Beacons For Environmental Monitoring In Internet Of Things (Iot), George Dan Moiş, Teodora Sanislav, Silviu Corneliu Folea, Sherali Zeadally

Information Science Faculty Publications

Environmental conditions and air quality monitoring have become crucial today due to the undeniable changes of the climate and accelerated urbanization. To efficiently monitor environmental parameters such as temperature, humidity, and the levels of pollutants, such as fine particulate matter (PM2.5) and volatile organic compounds (VOCs) in the air, and to collect data covering vast geographical areas, the development of cheap energy-autonomous sensors for large scale deployment and fine-grained data acquisition is required. Rapid advances in electronics and communication technologies along with the emergence of paradigms such as Cyber-Physical Systems (CPSs) and the Internet of Things (IoT) have led to …

Applications Of Artificial Intelligence In Power Systems, Samin Rastgoufard

LSU New Orleans Theses and Dissertations

Artificial intelligence tools, which are fast, robust and adaptive can overcome the drawbacks of traditional solutions for several power systems problems. In this work, applications of AI techniques have been studied for solving two important problems in power systems.

The first problem is static security evaluation (SSE). The objective of SSE is to identify the contingencies in planning and operations of power systems. Numerical conventional solutions are time-consuming, computationally expensive, and are not suitable for online applications. SSE may be considered as a binary-classification, multi-classification or regression problem. In this work, multi-support vector machine is combined with several evolutionary computation …

A Human Powered Micro-Generator For Charging Electronic Devices, John Adam

Senior Theses

A hand-pulled generator has been designed and tested. A preliminary result has been obtained and discussed. This device was created to provide outlet-free charging. Electronic devices are useful when going out into the wilderness. A portable power supply is necessary to keep an electronic device alive. This project created a device that converts human energy into electricity to charge electronic devices. This thesis overviews the device’s design, build, and tests. Two different tests were run to determine that the device is capable of charging the storage battery. The device presented can provide 14 minutes of charging time with one hour …

Fabrication And Characterization Of Graphene Based 2d Materials For Supercapacitors, Anishkumar Manoharan

Graduate Theses and Dissertations

Supercapacitors have attracted a lot attention due to their efficient energy storage. In comparison to batteries, supercapacitors have high capacitance, energy, and power densities per unit mass than conventional capacitors. Carbon based materials are most promising in supercapacitor application due to their outstanding physical and electrochemical behavior. In this work, a facile method to synthesize a nanocomposite electrode consisting of annealed carbon from carbon ink and MoS2 was demonstrated. Effects of various aqueous and solid electrolytes were studied. It was found that the nanocomposite electrode with 10% MoS2 and 1M Na2SO4 as the aqueous electrolyte tested using the three electrode …