Electrical and Electronics Commons^™

Rapid Battery Exchange Safety And Sensing, Ben John Froelich, Isaac Sungjin Kim

Electrical Engineering

The Rapid Battery Exchange system (RBX) swaps batteries in an electric van, allowing almost continuous operation of the vehicle. The RBX system is designed and built by The Cal Poly Electric Vehicle Engineering Club (EVEC). The system includes the exchange ramp, two battery packs, and the electric “G-Van.” While the vehicle drives using one of the battery packs, the other pack charges in the exchange ramp. When the van’s battery depletes, it drives onto the ramp and swaps the dead battery for the charged one, and the process repeats.

The RBX battery pack safety and sensing project divides into two …

Low Voltage Cmos Sar Adc Design, Ryan Hunt

Electrical Engineering

This project centers on the design of a single ended 10-bit successive approximation register analog to digital converter (SAR ADC for short) that easily interfaces to a micro-controller, such as an Arduino. With micro-controller interfacing in mind, the universal data transfer technique of SPI proved an easy way to communicate between the ADC and the micro-controller. The ADC has a range of 1V (highest code value) to 0V (lowest code value) and operates from a single voltage rail value of 1.8V. Typical SPI clock speeds run on the order of 2MHz and with a 10-bit ADC this means a sampling …

Investigation Of Degradation Effects Due To Gate Stress In Gan-On-Si High Electron Mobility Transistors Through Analysis Of Low Frequency Noise, Michael Curtis Meyer Masuda

Master's Theses

Gallium Nitride (GaN) high electron mobility transistors (HEMT) have superior performance characteristics compared to Silicon (Si) and Gallium Arsenide (GaAs) based transistors. GaN is a wide bandgap semiconductor which allows it to operate at higher breakdown voltages and power. Unlike traditional semiconductor devices, the GaN HEMT channel region is undoped and relies on the piezoelectric effect created at the GaN and Aluminum Gallium Nitride (AlGaN) heterojunction to create a conduction channel in the form of a quantum well known as the two dimensional electron gas (2DEG). Because the GaN HEMTs are undoped, these devices have higher electron mobility crucial for …

Quantum Efficiency Enhancement For Gan Based Light-Emitting Diodes And Vertical Cavity Surface-Emitting Lasers, Fan Zhang

Theses and Dissertations

This thesis explores the improvement of quantum efficiencies for InGaN/GaN heterostructures and their applications in light-emitting diodes (LEDs) and vertical cavity surface-emitting lasers (VCSELs). Different growth approaches and structural designs were investigated to identify and address the major factors limiting the efficiency. (1) Hot electron overflow and asymmetrical electron/hole injection were found to be the dominant reasons for efficiency degradation in nitride LEDs at high injection; (2) delta p-doped InGaN quantum barriers were employed to improve hole concentration inside the active region and therefore improve hole injection without sacrificing the layer quality; (3) InGaN active regions based on InGaN multiple …

Electron – Phonon Interaction In Multiple Channel Gan Based Hfets: Heat Management Optimization, Romualdo A. Ferreyra

Theses and Dissertations

New power applications for managing increasingly higher power levels require that more heat be removed from the power transistor channel. Conventional treatments for heat dissipation do not take into account the conversion of excess electron energy into longitudinal optical (LO) phonons, whose associated heat is stored in the channel unless such LO phonons decay into longitudinal acoustic (LA) phonons via a Ridley path. A two dimensional electron gas (2DEG) density of ~5×10¹²cm^-2 in the channel results in a strong plasmon–LO phonon coupling (resonance) and a minimum LO phonon lifetime is experimentally observed, implying fast heat removal from …

Measurement And Modeling Of Humidity Sensors, Jingbo Tong

Theses and Dissertations--Electrical and Computer Engineering

Humidity measurement has been increasingly important in many industries and process control applications. This thesis research focus mainly on humidity sensor calibration and characterization. The humidity sensor instrumentation is briefly described. The testing infrastructure was designed for sensor data acquisition, in order to compensate the humidity sensor’s temperature coefficient, temperature chambers using Peltier elements are used to achieve easy-controllable stable temperatures. The sensor characterization falls into a multivariate interpolation problem. Neuron networks is tried for non-linear data fitting, but in the circumstance of limited training data, an innovative algorithm was developed to utilize shape preserving polynomials in multiple planes in …

Physical Design Of A Smart Camera With Integrated Digital Pixel Sensors Using A 0.13Μm 8-Layer Metal Cmos Process, Mahir K. Gharzai

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

The design of cameras has historically kept imagery and computational circuitry isolated in an attempt to maximize image quality by improving pixel pitch and routing density. Although this technique has worked in creating high density arrays of pixels for large resolution imagers, it has never been able to achieve high framerate computational operations.

A radical approach is introduced to solve this dilemma by creating compact, low- power pixel elements with built-in analog-to-digital converters that directly interface with digital logic. These pixels are capable of integrating alongside logic cells and to create an array of pixels inside the processor that can …

Investigation Of The Effects Of Rapid Thermal Annealing On Mbe Grown Gaasbi/Gaas Heterostructures For Optoelectronic Devices, Perry C. Grant

Graduate Theses and Dissertations

High efficiency optoelectronic devices rely on high quality materials making up the device structure. The scope of this thesis investigates the effectiveness of rapid thermal annealing (RTA) at improving the material quality of GaAsBi/GaAs heterostructures. During the fabrication of a device, the contacts of the device had the rapid thermal annealing process accomplished to produce ohmic contacts and this research explored if this annealing treatment degraded the quantum wells that made up the active region of a device. To investigate these effects, a system to measure the photoluminescence of the material system was constructed utilizing Fourier Transform Infrared Spectroscopy. The …

A Novel Design Optimization Of A Fault-Tolerant Ac Permanent Magnet Machine-Drive System, Peng Zhang

Dissertations (1934 -)

In this dissertation, fault-tolerant capabilities of permanent magnet (PM) machines were investigated. The 12-slot 10-pole PM machines with V-type and spoke-type PM layouts were selected as candidate topologies for fault-tolerant PM machine design optimization problems. The combination of 12-slot and 10-pole configuration for PM machines requires a fractional-slot concentrated winding (FSCW) layout, which can lead to especially significant PM losses in such machines. Thus, a hybrid method to compute the PM losses was investigated, which combines computationally efficient finite-element analysis (CE-FEA) with a new analytical formulation for PM eddy-current loss computation in sine-wave current regulated synchronous PM machines. These algorithms …

Theoretical Analysis Of Laterally Vibrating Hammerhead Microcantilever Sensors In A Viscous Liquid, Jinjin Zhang

Dissertations (1934 -)

Dynamically driven prismatic microcantilevers excited in the in-plane flexural mode have been investigated and used in liquid-phase sensing applications. However, the performance is restricted due to their limited surface sensing area and higher stiffness in shorter and wider prismatic microcantilevers. To increase the surface sensing area, and further improve sensing characteristics, it has been proposed to investigate symmetric hammerhead microcantilevers vibrating laterally in viscous liquid media. In this work, a theoretical model is proposed and the characteristics of the microcantilevers with symmetric shaped hammerheads (isosceles trapezoid, semi-circle, uniform rectangle and composite rectangle) are investigated. In the analysis, the stem of …

Understanding Vehicular Traffic Behavior From Video: A Survey Of Unsupervised Approaches, Brendan Tran Morris, Mohan Manubhai Trivedi

Electrical & Computer Engineering Faculty Research

Recent emerging trends for automatic behavior analysis and understanding from infrastructure video are reviewed. Research has shifted from high-resolution estimation of vehicle state and instead, pushed machine learning approaches to extract meaningful patterns in aggregates in an unsupervised fashion. These patterns represent priors on observable motion, which can be utilized to describe a scene, answer behavior questions such as where is a vehicle going, how many vehicles are performing the same action, and to detect an abnormal event. The review focuses on two main methods for scene description, trajectory clustering and topic modeling. Example applications that utilize the behavioral modeling …

Design And Fabrication Of Inverter And Rectifier Modules For Indirect Matrix Converter Applications, Saikishore Talakokkula

Graduate Theses and Dissertations

In power converter applications, silicon carbide (SiC) power semiconductor devices are preferred over their silicon counterparts due to many advantages such as wide bandgap, high junction temperatures and low on-state resistance. The SiC devices provide reduced conduction and switching losses. Due to the above mentioned advantages the power conversion efficiency of SiC devices is better compared to that of silicon (Si) devices.

This thesis studies the implementation of 1200V/17A Normally-off SiC JFETs for an indirect matrix converter (IMC) application. A discussion on the parasitic inductance optimization is presented based on the electromagnetic simulation results extracted from the Ansoft Q3D extractor. …

High Voltage Direct Current Energy Transmission Using Modular Multilevel Converters, David Alejandro Guzman Pinzon

Graduate Theses and Dissertations

This thesis focus on high voltage direct current (HVdc) energy transmission using modular multilevel converter (MMC) based terminals. It provides a brief comparison between different HVdc technologies, focusing on voltage source converters (HVdc-VSC) with the MMC-based terminal emerging as the topology of choice for ratings less than 1 GW. The controllers for a two-terminal HVdc-link are analyzed and Matlab/Simulink^TM simulation models are presented. The simplified models and full Matlab/Simulink^TM based model are used to select the gains for the MMC controllers. Simulation results carried out on the full model validated the proposed methodologies. A new control technique that …

Electrical Design Considerations And Packaging Of Power Electronic Modules, Shijie Wang

Graduate Theses and Dissertations

A modern power electronic module can save significant energy usage in the power electronic systems by improving their switching efficiencies. One way to improve the efficiency of the power electronic module is to reduce its parasitic circuit elements. The purpose of this thesis is to investigate the mitigation of parasitic circuit elements in power electronic modules. General methods of mitigating parasitic inductances were analyzed by the Q3D Extractor and verified by the time-domain reflectometry (TDR) measurements. In most cases, the TDR measurement results closely matched those predicted by the Q3D Extractor. These methods were applied to design and analyze a …

2-Dimensional Personal Motion Energy Harvester For Low Power Electronics, Manuel Gutierrez, Sean Scott, Dimitrios Peroulis

The Summer Undergraduate Research Fellowship (SURF) Symposium

In a lab, it becomes crucial to have a way to monitor that lab workers aren’t exposed to too much radiation. Such a device that detects this should have an energy harvester so that batteries aren’t required. The need for an energy harvester that generates power from a user’s movements in 2 dimensions is needed. This energy harvester is needed to power a radiation monitor. An energy harvester that generates power based off movements in 2 dimensions was developed. The energy harvester was created through a series of prototypes. Each prototype was built from a CAD drawing and a stereolithography …

Lunalight - Bringing Light To The Expanding World, Gabriela M. Igel, Daniel J. Patrick, Kimberley M. Smith

Materials Engineering

The LunaLight, a solar rechargeable light and cell phone charger, addresses the lack of access to electricity faced by 1.4 billion of the world’s population (International Finance Corporation). The LunaTech team has developed a product that is bright, simple, compact, versatile and competitive with existing products. Through a partnership with the non-profit organization One Million Lights, LunaTech has improved a previous team’s design to address user feedback, concerns of durability, and manufacturability.

The LunaLight design includes a 5 component plastic housing held together by 4 screws, a surface mounted PCB, a lithium-ion (Li-Ion) battery, one high-brightness LED, a solar panel, …

Spice Netlist Generation For Electrical Parasitic Modeling Of Multi-Chip Power Module Designs, Peter Tucker

Electrical Engineering Undergraduate Honors Theses

Multi-Chip Power Module (MCPM) designs are widely used in the area of power electronics to control multiple power semiconductor devices in a single package. The work described in this thesis is part of a larger ongoing project aimed at designing and implementing a computer aided drafting tool to assist in analysis and optimization of MCPM designs. This thesis work adds to the software tool the ability to export an electrical parasitic model of a power module layout into a SPICE format that can be run through an external SPICE circuit simulator. The code was implemented in python using NetworkX graphs …

Digitally Programmable Rf Mems Filters With Mechanically Coupled Resonators, Hengky Chandrahalim, Sunil Ashok Bhave

AFIT Patents

A digitally-tunable RF MEMS filter includes a substrate and a plurality of mechanically coupled resonators, wherein a first and a last resonator of the plurality of mechanically coupled resonators are configured to be electrostatically transduced. One or more of the plurality of mechanically coupled resonators are configured to be biased relative to the substrate such that the one or more biased resonators may be brought substantially in contact with the substrate. In a method of digitally tuning an RF MEMS filter having a mechanically coupled resonator array, a DC bias voltage is applied to at least a first resonator and …

Dc, Rf, And Thermal Characterization Of High Electric Field Induced Degradation Mechanisms In Gan-On-Si High Electron Mobility Transistors, Matthew Anthony Bloom

Master's Theses

Gallium Nitride (GaN) high electron mobility transistors (HEMTs) are becoming increasingly popular in power amplifier systems as an alternative to bulkier vacuum tube technologies. GaN offers advantages over other III-V semiconductor heterostructures such as a large bandgap energy, a low dielectric constant, and a high critical breakdown field. The aforementioned qualities make GaN a prime candidate for high-power and radiation-hardened applications using a smaller form-factor. Several different types of semiconductor substrates have been considered for their thermal properties and cost-effectiveness, and Silicon (Si) has been of increasing interest due to a balance between both factors.

In this thesis, the DC, …

Investigation Of Cds Nanowires And Planar Films For Enhanced Performance As Window Layers In Cds-Cdte Solar Cell Devices, Jianhao Chen

Theses and Dissertations--Electrical and Computer Engineering

Cadmium sulfide (CdS) and cadmium telluride (CdTe) are two leading semiconductor materials used in the fabrication of thin film solar cells of relatively high power conversion efficiency and low manufacturing cost. In this work, CdS/CdTe solar cells with a varying set of processing parameters and device designs were fabricated and characterized for comparative evaluation. Studies were undertaken to elucidate the effects of (i) each step in fabrication and (ii) parameters like thickness, sheet resistance, light absorptivity solution concentration, inert gas pressure etc. Best results were obtained when the thickness of CdS planar film for the window layer was in the …

Wireless Sensor Networks And The Internet Of Things, Yingtao Jiang, Lei Zhang, Ling Wang

Electrical & Computer Engineering Faculty Research

It is estimated that mobile internet devices that can act as sensors will outnumber humans this year (2013), and by 2015, there will be about 15 billion internet-connected devices. Related applications are thriving in commercial, civic, and scientific operations that involve sensors, web, and services, leading by both academic societies and industry companies. It is commonly accepted that the next generation of internet is becoming the “Internet of Things (IoT)” which is a worldwide network of interconnected objects and their virtual representations uniquely addressable based on standard communication protocols. Identified by a unique address, any object including computers, mobile phones, …

Estimation Of Performance Indices For The Planning Of Sustainable Transportation Systems, Alexander Paz, Pankaj Maheshwari

Electrical & Computer Engineering Faculty Research

In the context of sustainable transportation systems, previous studies have either focused only on the transportation systemor have not used a methodology that enables the treatment of incomplete, vague, and qualitative information associated with the available data. This study proposes a system of systems (SOS) and a fuzzy logic modeling approach. The SOS includes the Transportation, Activity, and Environment systems. The fuzzy logic modeling approach enables the treatment of the vagueness associated with some of the relevant data. Performance Indices (PIs) are computed for each system using a number of performance measures. The PIs illustrate the aggregated performance of each …

Modeling Leakage Currents In Metal Insulator Metal Structures With High K Materials, Priyamvada Maleeswaran

Electrical & Computer Engineering Theses & Dissertations

Various products such as personal computers, cellular phones and mobile devices require high speed and low power consumption. Such improvements have been attained by minimizing physical dimensions of electronic devices, leading to high density integration of transistors and capacitors on integrated chips (]Cs). However, as a consequence of down-scaling device dimensions, tunneling of electrons through thin gate oxides (SiO₂) increases, leading to increased static power leakage. This constitutes wastage in power, and for the case of memory applications necessitates faster refresh cycles. In order to overcome such issues, high-k materials (such as HfO₂ and ZrO₂) …

Modeling Of Power Semiconductor Devices, Tanya Kirilova Gachovska

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

One of the requirements for choosing a proper power electronic device for a converter is that it must possess a low specific on-resistance. The specific on-resistance of a bipolar device is related to the base width and doping concentration of the lightly doped drift region. This means that the doping concentration and the width of the low-doped base region in a bipolar device must be carefully considered to achieve a desired avalanche breakdown voltage and on-resistance. In order to determine the technological parameters of a semiconductor device, a one dimensional analysis is used to calculate the minimum depletion layer width, …

Delay Insensitive Ternary Logic Utilizing Cmos And Cntfet, Ravi Sankar Parameswaran Nair

Graduate Theses and Dissertations

As digital circuit design continues to evolve due to progress of semiconductor processes well into the sub 100nm range, clocked architectures face limitations in a number of cases where clockless asynchronous architectures require substantially less power, generate less noise, and produce less electromagnetic interference (EMI). This dissertation develops the Delay Insensitive Ternary Logic (DITL) asynchronous design paradigm that combines the designs aspects of similar Dual-Rail asynchronous paradigms and Boolean logic to create a single wire per bit, three voltage signaling and logic scheme.

DITL is designed at the transistor level using multi-threshold CMOS and carbon nanotube (CNT) FETs to develop …

Highly Sensitive X-Ray Detectors In The Low-Energy Range On N-Type 4h-Sic Epitaxial Layers, K. C. Mandal, P. G. Muzykov, J. R. Terry

Faculty Publications

No abstract provided.

Nanoscale Contacts Between Semiconducting Nanowires And Metallic Graphenes, Seongmin Kim, David B. Janes, Sung-Yool Choi, Sanghyun Ju

Birck and NCN Publications

Metal–semiconductor (M–S) junctions are important components in many semiconductor devices, and there is growing interest in realizing high quality M–S contacts that are optically transparent. In this paper, we present our investigations into the characteristics of M–S junction in a semiconducting ZnO nanowire that was directly grown on a multilayer graphene film (MGF). The synthesized nanowires were fabricated into two-terminal devices with MGF as one contact and Al as the other contact. By comparison with devices employing Al contacts at both ends, the nanowire resistivity and specific contact resistivity of the MGF–nanowire contact can be extracted. The extracted specific contact …

Fabrication And Characterization Of Torsional Micro-Hinge Structures, Mike Madrid Marrujo

Master's Theses

ABSTRACT

Fabrication and Characterization of Torsional Micro-Hinge Structures

Mike Marrujo

There are many electronic devices that operate on the micrometer-scale such as Digital Micro-Mirror Devices (DMD). Micro actuators are a common type of DMD that employ a diaphragm supported by torsional hinges, which deform during actuation and are critical for the devices to have high stability and reliability. The stress developed within the hinge during actuation controls how the actuator will respond to the actuating force. Electrostatically driven micro actuators observe to have a fully recoverable non-linear viscoelastic response. The device consists of a micro-hinge which is suspended by two …

Energy Harvesting From Elliptical Machines: Dc-Dc Converter Design Using Sepic Topology, Martin Kou

Master's Theses

Cal Poly’s ongoing Energy Harvesting from Exercise Machines (EHFEM) project is a very convenient and cost-effective way for generating DC power from physical exercise and sending it back to the electrical grid as AC power, providing a renewable energy source for the future. The EHFEM project consists of numerous subprojects involving converting different types of exercise machines for power generation. This project is a continuation of one of the previous subprojects, specifically involving an elliptical machine, and focuses on improving system functionality at different machine settings without altering the elliptical user’s experience by selecting a new DC-DC converter design, while …

Cell Phone Charger For The Dc House Project, Andrew Hefner, Antonio Magdaleno

Electrical Engineering

The goal of this project is to create a multiple output cell phone charger for the DC House project. The cell phone charger is essentially a DC-DC converter. The converter takes an input of 48 volts from the outlet in the DC House and decreases the voltage level to 5 volts; the input voltage level of all cellular devices. By designing an isolated flyback converter with initial specification in LTSpice simulation software, a converter was created. By monitoring the input and output voltage and current using the multi-meters and electronic load, we determined the charger to be 71% efficient when …