Civil Engineering Commons^™

Calibration Of Numerical Model For Shoreline Change Prediction Using Satellite Imagery Data, Sigit Sutikno, Keisuke Murakami, Dwi Puspo Handoyo, Manyuk Fauzi

Makara Journal of Technology

This paper presents a method for calibration of numerical model for shoreline change prediction using satellite imagery data in muddy beach. Tanjung Motong beach, a muddy beach that is suffered high abrasion in Rangsang Island, Riau province, Indonesia was picked as study area. The primary numerical modeling tool used in this research was GENESIS (GENEralized Model for Simulating Shoreline change), which has been successfully applied in many case studies of shoreline change phenomena on a sandy beach.The model was calibrated using two extracted coastlines satellite imagery data, such as Landsat-5 TM and Landsat-8 OLI/TIRS. The extracted coastline data were analyzed …

Independency Of Elasticity On Residual Stress Of Room Temperature Rolled Stainless Steel 304 Plates For Structure Materials, Parikin Parikin, David Allen

Makara Journal of Technology

Mechanical strengths of materials are widely expected in general constructions of any building. These properties depend on its formation (cold/hot forming) during fabrication. This research was carried out on cold-rolled stainless steel (SS) 304 plates, which were deformed to 0, 34, 84, and 152% reduction in thickness. The tests were conducted using Vickers method. Ultra micro indentation system (UMIS) 2000 was used to determine the mechanical properties of the material, i.e.: hardness, modulus elasticity, and residual stresses. The microstructures showed lengthening outcropping due to stress corrosion cracking for all specimens. It was found that the tensile residual stress in a …

Effect Of Fly Ash Fortification In The Manufacture Process Of Making Concrete Towards Characteristics Of Concrete In Sulfuric Acid Solution, Asep Handaya Saputra, Muhammad Shohibi, Masatoshi Kubouchi

Makara Journal of Technology

Fly ash is a silica or alumino silica material that can be used as a constituent of cement in the concrete manufacturing process. Utilization of fly ash aims to improve durability and minimize the reduction of concrete’s compressive strength exposed to an acidic environment, which can be achieved through the pozzolanic reaction of fly ash with Ca(OH)2 within concrete. The reduced content of Ca(OH)2 through pozzolanic reaction will minimize the tendency of ettringite formation (compounds that cause deterioration and decrease the compressive strength of concrete). In order to determine the relation between fly ash replenishment into concrete with concrete’s characteristics …

Improving Renewable Energy Transition Acceptance: A Simulation Gaming Approach On A Multi Actor Setting In The Netherlands, Aziiz Sutrisno, Jac A. M. Vennix, Noor Syaifudin

Makara Journal of Technology

The Netherlands have tried very hard to increase their renewable energy sources (RES) shares to fulfill the European Union target in 2050. However, RES performance did not show the expected result as the performance declined in 2009 producing even wider gap compare to the target. The Dutch government’s tried to incorporate all interested stakeholders by forming the Dutch energy transition task force. Nevertheless, the task force’s result is also not showing a desirable trend. Key reasons behind the Dutch low RES performance are the lack of shared understanding and positive attitude toward RES development among interested actors. This research uses …

Oxidation Process Of H 2 O /Uv For Cod Reduction Of Wastewater From Soybean Tofu Production, Komala Pontas, Abrar Muslim

Makara Journal of Technology

Chemical Oxygen Demand (COD) reduction of wastewater from soybean tofu production was studied by conducting advanced oxidation process (AOP) using hydrogen peroxide with UV radiation catalysts in a closed cylindrical glass reactor. The hydroxyl radical (*OH) concentration from H2O2 decomposition was modeled, and exponential trends were found for the *OH concentration over radiation time and operation temperature. As a result, it was found that the maximal *OH concentration was 0.209 mol L-1 at 240 minutes and 50 °C. The *OH concentration exponentially increased following rise in operation temperature. The H2O2/UV AOP application reduced COD concentration to approximately 42.41% from 10,545 …

Uplift Of Shoreline Regions On Pagai Island Due To The September 12, 2007 Mw 8.4 Earthquake Captured By Sar Image, Ashar Muda Lubis

Makara Journal of Technology

At least 25 people were killed by the September 12, 2007 Mw 8.4 Bengkulu earthquake, and many buildings were destroyed in Bengkulu and West Sumatra provinces. It is very important to estimate the earth surface deformation due to the earthquake to understand the rupture size and its process. The aim of this research is to estimate the shoreline change and vertical displacement on Pagai Island associated with the September 12, 2007 Mw 8.4 Bengkulu earthquake. The intensity of ALOS-PALSAR satellite images is used to access the pattern of displacement. The result shows that Pagai Island demonstrated huge uplift due to …

Dual-Band Singly-Fed Proximity-Coupled Tip-Truncated Triangular Patch Array For Land Vehicle Mobile System, Basari Basari, Josaphat Tetuko Sri Sumantyo

Makara Journal of Technology

This paper proposes a dual-band left-handed circularly polarized triangular-patch array that is developed for land vehicle mobile system aimed at mobile satellite communications. The array consists of six tip-truncated triangular patches, which the first three patches are used for reception and the second three patches are used for transmission purpose. Each of three-patches has a beam pattern that can be switched in three different 120°-coverage beam in azimuth-cut plane at a minimum targeted gain at a desired elevation angle. The targeted minimum gain of the array is 5 dBic, in order for data communications with a large geostationary satellite can …

Improvement Of Quality Of Carica Papaya L. With Clove Oil As Preservative In Edible Coating Technology, Eny Kusrini, Anwar Usman, Chrispine Deksita Wisakanti, Rita Arbianti, Dedy Alharis Nasution

Makara Journal of Technology

We have studied utilization of essential clove oil, extracted from clove buds by hydrodistillation, as preservative in edible packaging technology. Preservative of essential clove oil was applied on chopped papaya fruits by using two methods, namely spray and brush. The effects of concentration of clove oil from 0.05 to 0.20% on the preservation of papaya fruits (Carica papaya L.) at room temperature (25 °C) were also evaluated. Physicochemical and in vitro microbiological activities on the papaya fruits that were stored at 25 oC and 85-90% relative humidity were investigated in details. The results indicate that the clove oil at concentration …

Comparative Analysis Of Buckling-Restrained Braced Frames In Eccentric Configuration (Brbf-Es) And Eccentrically Braced Frames (Ebfs), Peter T. Vayda

Civil Engineering Undergraduate Honors Theses

Continuing on the findings of “Using Buckling-Restrained Braced Frames in Eccentric Configuration,” by Dr. Gary S. Prinz, P.E., which determined that, from a performance standpoint, BRBF-Es could be a viable alternative for EBFs. A comparative analysis was conducted on the design procedures and initial cost estimates of BRBF-Es and EBFs. Upon designing four 12-Story buildings (two BRBF-Es and two EBFs), it was determined that BRBF-Es were easier to design due to the statically determinant system. The initial costs estimates of BRBF-Es; however, ranged upwards of 30% more cost than EBFs. Therefore, the initial investment of more intensive structural engineering design …

Cultural Change Through Bim: Driving Lean Transformation In Education, Avril Behan, Malachy Mathews, Kevin Furlong, Ciara Ahern, Una Beagon, Peter Brennan, Colin Conway, Lee Corcoran, Pierce Fahy, Alan Hore, Barry Mcauley, Trevor Woods

Conference papers

This paper presents a case study of how the adoption of BIM-based practices in the AECO industry is being reflected by cultural change in higher education in Ireland. The silo-mentality that has dominated the AECO sector for more than a century has, despite numerous reorganisations, been replicated in the structures of educational institutions, including in Dublin Institute of Technology since the inception of its founding colleges in the late 1800s. Most AECO programmes must include content that is external to the programme’s specific discipline. Through the School structures of the Institute, delivery of such content is known as "service teaching" …

Assessment Of Wood Processing Engineers By Requirements Of Leading Manufacturing Entities In Albania, Ramadan Topuzi, Arden Bejtja

UBT International Conference

In Albania a significant number of wood-processing engineers exercise this profession in the field of manufacturing and trading of furniture. In this sector exercise their activity over 800 manufacturing entities distributed across the country with about 9,000 employees. The main purpose of the study is the assessment of wood processing engineers as perceived by the manufacturing entities and their adaptation to the requirements of the labor market . The data collected through a structured questionnaire for this purpose, are thrown into a database (where they are analyzed to generate the results given in this paper. The selection of the respondents …

Motorizing Cbd Of Tirana. A Before And After Study In Tirana From Sustainability Point Of View, Edison Barhani

UBT International Conference

The Center Business District of Tirana (Skanderbeg Square) plays a crucial part in Tirana Transportation System. After a closure of about 2 years, being under reconstruction, CBD opened to traffic on November 14th, 2011. This study analyses performance parameters like: travel time for both cars and buses, waiting time at bus stations, and passenger boarding/alignment for bus passing through or around the CBD before and after it was opened to traffic. Route that follows Kinostudio-Kombinat bus line has been selected as a representative of all other lines passing through the center of Tirana. Opened to traffic for the supply to …

Structural Analysis Of A Typical Highway Bridge Comparison Between Ktp, En And Aashto Load Models, Endrit Berisha

UBT International Conference

This study consists on a structural analysis comparison of a typical highway bridge between KTP, EN and AASHTO based on load capacity. The Eurocodes are currently in the process of national implementation towards becoming the Europe wide means for structural design of civil engineering works. A team from Mott Macdonald inspected 562 bridges and the main causes of the defects are figured out in the study as traffic load, nature force, and aging, lack of maintenance and design deficiencies. As design codes are advancing with time, the need of Albania to upgrade its code has become a must. This paper …

Effect Of Steel Fiber And Polypropylene Fiber On Reinforced Concrete, Erjola Reufi, Jozefita Marku

UBT International Conference

This paper presents the results of an experimental study that investigated, the effects of steel fibers and polypropylene fibers on the mechanical properties of concrete. Two types of fibers used are hooked end steel fibers of 50 mm and 30 mm length with the aspect ratio of 67 (length 50 mm and diameter 0.75 mm) and 44 (length 30 mm and diameter 0.75 mm). On the other hand, three types of polypropylene fibers are used of length 12mm, 6mm and 3 mm. Steel fibers are used of 0%, 0.25%, 0.5%, and 1% by the volume of concrete and polypropylene fiber …

A Study On Tibiofemoral Joint Contact Area Stresses Using Finite Element Method, Anjeza Gjini, Altin Bidaj, Enio Deneko, Drilona Disha

UBT International Conference

The joints of the human body act as mechanical or building structures joints. Joints connect different segments by enabling the movement of these segments. The design of a joint that provides durability or static support differs from that one which provides only movement. Joints of the human body, as organic joints, are considered more complex than other types of joints. Finite element models help to comprehend the knee structure behavior under the action of dynamic and static loads. Deformations in the articulating cartilage and the distribution of loads from meniscus provide data to understand the effect of loads in different …

Application Of Ec Regulations On Assessment Of The Effect Of Fire On Buildings, Xhemshir Mulliqi

UBT International Conference

The last decade has been characterized by construction of multi-storey buildings in almost all cities of Kosovo, with the storey-height ranging from B+G+4 to B+G+11 and even B+G+15, which means that they need to be subjected to the revision of the main project, including things be verified for the effect of fire. This paper aims to illustrate the use of EC regulations for the verification of reinforced concrete structures under effect of fire, respectively: EN 1991-2-2 Basis of design and actions on structures. Part-2.2: Actions on structures exposed to fire and EN 1992-1-2:2004 Design of concrete structures- part -1-2: Structural …

Application Of En 1991-1-2 Annex E, Using’S Software Package, Xhemshir Mulliqi

UBT International Conference

The fire may occur anywhere and in any phase in the lifetime of a building .Fire resistance requirements should be based on the parameters influencing fire growth and development. For calculating the characteristic fire load, the characteristic fire load has to be determined using the table of EN 1991-1-2 Annex E.The aim of this paper is to present the methodology used in this tool and to show an example of application. The fire resistance of a steel beam submitted to compartment fires which supports a non-collaborating concrete slab in a compartment is estimated in case of an unprotected and a …

Reducing The Porosity And Sealing Cracks By Using Crystalline Admixture In Conventional Concrete, Visar Krelani, Liberato Ferrara

UBT International Conference

There is a continuous increase of quality on civil engineering materials in developed countries and parallel increase of need for new constructions in developing countries. Professional community should propose solutions for the durability that can resist in different severe environments. The most important factor that can affect concrete durability is represented by the pore distribution. Transport properties can take place through the porous network inside the cementitious composites and the aggregates interface, permitting the ingress of aggressive agents damaging concrete function intrinsically as a material and the well-functioning of the entire structure. The use of a crystalline admixture during the …

The Impact Of Municipal Waste Water In Neredime River, Kosovo, Bekim Selimi

UBT International Conference

Today, environmental protection is of great concern in Kosovo. Almost all waste water effluents from the localities are discharging in surface water and groundwater without being significantly treated deterioning water quality in Kosovo’s rivers. The aim of this paper is to analyze the level of pollution in the Neredime river created from municipal wastewater as well as to identify pollutants and their impact on the river. An attempt has been made to present the situation of the waters defining physicochemical water qualities of Neredime river from the source to the outskirts of town in the south-west of Ferizaj; this includes …

Design Of Bearing Capacity Of The Driven Piles Of A Highway Bridge Foundation According To 3 Different Methods, Papa Dhimitri, Dervishi Idlir

UBT International Conference

Contemporary design methods of bearing capacity of deep foundation (pile foundation) change according to different design codes. The main requisition of the designing process of the deep foundation is related with the axial bearing capacity, which should be sufficient to withstand the applied loads. Many authors has developed and published detailed methods to analyze the behavior of a single reinforced concrete pile or a group of piles, based on vertical bearing capacity due to lateral friction or residence at the pile point. The goal of this paper is to illustrate the calculation methods according to 3 analytical methods of vertical …

Advanced Construction Materials For Highway Applications, Altin Bidaj, Irakli Premti, Hektor Cullufi

UBT International Conference

Nowadays cost of highway materials increase every year. In addition, use of marginal materials results in early development of pavement distress, requiring more frequent repairs also rehabilitation, associated lane closures, traffic congestion in high volume traffic areas which increases the potential for construction zone accidents and increased levels of environmental pollution related to automobile emissions. Therefore, there is a strong desire in our country to optimize the use of materials currently used for highway pavement construction and to seek advanced materials that are cheaper and environmentally friendly. It has now been recognized that the age of limitless construction materials and …

Processing Of Gis Data And Building Of 3d Dem Models With Fme Transformer Tools, Hebib Alili, Fadil Shehu, Shenur Muslija

UBT International Conference

The processes of processing of 2D or 3D geodetic or geo-information data by using the FME software and other software's or tools in combination and then through mathematical logics in FME building of such 3D models from original measured terrain data within transformers given by FME, could be considered as very important attempt of creating of such 3D models, exactly when we have to deal with huge data by the size of its as input data. These kind of doing of processing of data through FME software, can be considered as important issue also for resolving of other today related …

The Effects Of Recycling Asphalt Use In Terms Of Economic Growth And Environmental Improvement In Kosova, Muhamet Ahmeti, Binak Beqaj

UBT International Conference

Through this paper is analysed the possibility of recycling asphalt and reusing this in receipts of new asphalt to build road infrastructure inside urban areas and inter-urban areas, because analysing the investments that are being realized in the road infrastructure in Kosova last years, and investments that are going on, there are indicators showing economical, environmental and ….benefits of the society .

According to database of the Kosova Ministry of Transport and Telecommunication until the year 2014, the territory of Kosova has 2005.5 km of the road, 4% are highways, magisterial roads 32% and 64% regional roads, most of them …

Climate Change And Drinking Water, Muhamet Ahmeti, Ilira Abdullahu

UBT International Conference

The period June 2012 – March 2014 saw a prolonged deficit of precipitation below normal. This led to a major continental scale drought across southern Europe, and in eastern Kosova in particular. E.g. see figure 1 below for the month of December 2013, from Drought Monitoring Center for SEE. In fact December 2013 was the fifth driest month in the recorded history of Kosova. February registered the driest month in the recorded hydro-meteorological history of Kosova, since 1927 with only 2.1 mm precipitation, which expressed in Standardized Precipitation Index (SPI). The chance of getting this value in February was 1 …

Imperfection Impact On Behavior Of The Secondary Nonstructural Elements And Vertical Non Precise Erection Of Members, Armend Mujaj, Florim Grajçevci, Driton R. Kryeziu, Zijadin Guri, Fisnik Kadiu

UBT International Conference

In this paper of works will be try to present the fundamental computation referring to the imperfection impacts phenomena of non-precise erection effects of the structural members as are vertical columns. Depends from the structural type, the structure should have a vertical structural members with the enough vertical and shear capacity provoked from horizontal action of earthquake, wind, dead and imposed vertical loads. The structural designers, during the structural computation are improve the several approximations creating the dynamic modeling, having into the consideration of structural elements classification in the prior and secondary structural elements. It is very none that the …

Experimental And Predicted Behavior Of Frp Beam-Columns Including Retrofitting, Ali Al-Huazy

Civil & Environmental Engineering Theses & Dissertations

This thesis presents the outcome of a theoretical and experimental study of Fiber Reinforce Polymer (FRP) beam-columns with uniaxial bending and including retrofitting. The research involved the design and fabrication of a testing apparatus which was then used for a series of beam-column tests. Three different types of beam-column cross sections were used, namely, channel section, I-section, and square tube section. Six non-retrofitted beam-columns were tested in addition to two retrofitted ones. The members were subjected to an eccentric vertical load applied through a lever arm generating gradually increasing axial load and uniaxial bending moment up to the maximum load. …

Behavior And Strength Of Pultruded Frp I-Section Columns Including Uniaxial And Biaxial Bending, Emad M. Amin

Civil & Environmental Engineering Theses & Dissertations

This thesis presents the outcome of a study of the behavior and strength of pultruded glass fiber reinforced polymer (FRP) I-section columns including uniaxial and biaxial applied bending moments. Also included in the study is a critical assessment of ASCE-LRFD Pre-standard for pultruded FRP structures in view of the rigorous analysis presented herein. The theoretical solution is based on a system of three coupled differential equations of equilibrium combined with pinned flexural and torsional boundary conditions. Effects of induced warping due to second-order terms as well as initial out-of-straightness are accounted-for in the governing differential equations. Detailed investigations into the …

Role Of Soil Parameters On Loading Of Buried Structures, Xiao Zhang, Mark D. Bowman, Rafael R. Armendariz Briones

The Summer Undergraduate Research Fellowship (SURF) Symposium

Load rating is the process to evaluate and explore the structural capacity of bridges as much as possible within safety range. As a balance between economy and safety, proper load ratings save money and keep public safe. Knowing the contribution and interaction of each different soil parameter on the loading can significantly reduce the amount of work when load rating those structures. However, for buried structures without plans, such contribution or interaction is never known. This parametric study explores how much each soil parameter of three types of soils can affect the loading of buried structures without plans. An existing …

Seismic Vulnerability Assessment Of Low-Rise Reinforced Concrete Buildings In Kathmandu, Nepal, Prateek Pratap Shah, Santiago Pujol

The Summer Undergraduate Research Fellowship (SURF) Symposium

In seismically active cities like Kathmandu, there often exists a need to assess the seismic vulnerability of a large number of poorly designed buildings within a short period of time. Traditional analysis techniques do not work because they require building data that are either inaccurate or unavailable. One alternative to traditional analysis techniques is to use simple correlations like the Priority Index. This index uses basic building information such as floor area, column area, and wall area to estimate the seismic vulnerability of a building. Following the 2015 Nepal earthquake, 146 low-rise reinforced concrete buildings were surveyed in Kathmandu, Nepal. …

Application Of Fiscal Incentives For Development Of East Natuna Gas Field For Long-Term National Natural Gas Demand, Marwan Batubara, Widodo Wahyu Purwanto, Akhmad Fauzi

Makara Journal of Technology

East Natuna gas field, which has proven reserves of 46 trillion cubic feet, is projected to meet long-term natural gas needs. However, CO2-content of the gas reserves reaches 71%, leading to expensive development costs. This research investigates the feasibility of the field based on several fiscal incentives. Firstly, gas supply-demand until year 2040 was analyzed. Then, based on the analysis, the field was developed using high CO2 gas separation technology to produce gas of 1300 MMSCFD in 2023, 2600 MMSCFD in 2031, and 3900 MMSCFD in 2039. Finally, the economic feasibility was assessed using cash flow analysis in accordance with …