Open Access. Powered by Scholars. Published by Universities.®

Civil and Environmental Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Brigham Young University

Discipline
Keyword
Publication Year
Publication
Publication Type
File Type

Articles 481 - 510 of 1183

Full-Text Articles in Civil and Environmental Engineering

Evaluation Of The Accuracy Of Approach Volume Counts And Speeds Collected By Microwave Sensors, Gregory Hans Sanchez Mar 2016

Evaluation Of The Accuracy Of Approach Volume Counts And Speeds Collected By Microwave Sensors, Gregory Hans Sanchez

Theses and Dissertations

This study evaluates the accuracy of approach volumes and free flow approach speeds collected by the Wavetronix SmartSensor Advance sensor using the field data collected by JAMAR counter boards for free flow approach volumes and a TruCam LiDAR gun for approach speeds. The Advance sensor is primarily designed for dilemma zone reduction. It does not have the capability to differentiate between lanes, but the Advance sensor currently used has a detection range of up to 600 ft. and has the capability to track vehicles approaching the intersection. The Utah Department of Transportation (UDOT) wanted to use this capability to get …

Go to article

The Impact Of Bicycle Corridors On Travel Demand In Utah, Christopher Kent Haskell Mar 2016

The Impact Of Bicycle Corridors On Travel Demand In Utah, Christopher Kent Haskell

Theses and Dissertations

Bicycling as an alternate mode of transportation has been on the rise. It is environmentally friendly in nature and the associated health benefits have made it a popular choice for many types of trips. The purpose of this research is to increase understanding of the impacts of implementing bicycle corridors (as part of the Utah Department of Transportation's (UDOT) Inclusion of Active Transportation policy) on bicycle rate as a function of roadway characteristics. The results of this research will be used in determining when and where bicycle corridors will enhance the transportation system and an estimate of the overall impact …

Go to article

Design, Development And Testing Of Web Services For Multi-Sensor Snow Cover Mapping, Jiri Kadlec Mar 2016

Design, Development And Testing Of Web Services For Multi-Sensor Snow Cover Mapping, Jiri Kadlec

Theses and Dissertations

This dissertation presents the design, development and validation of new data integration methods for mapping the extent of snow cover based on open access ground station measurements, remote sensing images, volunteer observer snow reports, and cross country ski track recordings from location-enabled mobile devices. The first step of the data integration procedure includes data discovery, data retrieval, and data quality control of snow observations at ground stations. The WaterML R package developed in this work enables hydrologists to retrieve and analyze data from multiple organizations that are listed in the Consortium of Universities for the Advancement of Hydrologic Sciences Inc …

Go to article

A Comprehensive Python Toolkit For Harnessing Cloud-Based High-Throughput Computing To Support Hydrologic Modeling Workflows, Scott D. Christensen Feb 2016

A Comprehensive Python Toolkit For Harnessing Cloud-Based High-Throughput Computing To Support Hydrologic Modeling Workflows, Scott D. Christensen

Theses and Dissertations

Advances in water resources modeling are improving the information that can be supplied to support decisions that affect the safety and sustainability of society, but these advances result in models being more computationally demanding. To facilitate the use of cost- effective computing resources to meet the increased demand through high-throughput computing (HTC) and cloud computing in modeling workflows and web applications, I developed a comprehensive Python toolkit that provides the following features: (1) programmatic access to diverse, dynamically scalable computing resources; (2) a batch scheduling system to queue and dispatch the jobs to the computing resources; (3) data management for …

Go to article

Finite Element Modeling Of Shallow Embedded Connection Stiffness, Trevor Jones, Dr. Paul Richards Jan 2016

Finite Element Modeling Of Shallow Embedded Connection Stiffness, Trevor Jones, Dr. Paul Richards

Journal of Undergraduate Research

Shallowly embedded connections are a common and important connection of steel columns to reinforced concrete foundations, which can increase the building’s overall stiffness and strength. Until now, their contributions have been neglected because they are hard to quantify and study. Previous research at BYU (Barnwell 2015) has shown that the strength and stiffness available in these connections is greater than was previously assumed. A thorough understanding of these desirable properties would allow engineers to design buildings that are more cost-effective.

Go to article

Thermal Properties Of Natural-Colored And Darkened Portland Cement Concrete Pavement, Tenli Waters, W. Spencer Guthrie Jan 2016

Thermal Properties Of Natural-Colored And Darkened Portland Cement Concrete Pavement, Tenli Waters, W. Spencer Guthrie

Journal of Undergraduate Research

The purpose of this project was to measure thermal properties of natural-colored and darkened portland cement concrete in order to explain observations from field data already collected. While portland cement concrete pavement offers a durable surface and long service life when designed and constructed properly, selected concrete pavement sections require expensive winter maintenance treatments to clear snow and ice. One method of potentially reducing winter maintenance costs is darkening the concrete pavement. Darkening the concrete reduces its albedo, or whiteness, and should therefore promote higher pavement surface temperatures through increased absorption of radiation energy from the sun. In winter, darkened …

Go to article

Laboratory Exercise- Mapping The Risk Of Structural Failure In Schools Due To An Earthquake, Joel Barker, Kimberly Sowards, Casey Webb Jan 2016

Laboratory Exercise- Mapping The Risk Of Structural Failure In Schools Due To An Earthquake, Joel Barker, Kimberly Sowards, Casey Webb

Engineering Applications of GIS - Laboratory Exercises

Utah’s present geology has been greatly dictated by tectonic stresses that have occurred over the last 0.7 Ga. A determining factor in much of this Geology is the Hingeline that runs through Salt Lake County. Throughout the history of the western North America, this has been an important weak zone. It is no surprise that this same zone is now home to the Wasatch Fault System, which accommodates some of the extension of Western North America. The steep mountains facing west toward Salt Lake City were formed from the tectonic processes of the Fault. The Wasatch Fault is a normal …

Go to article

Laboratory Exercise X – Most Dangerous Places To Live In The United States Based On Natural Disasters, Joshua Alpers, Luke Kevan, Santiago Tovar Jan 2016

Laboratory Exercise X – Most Dangerous Places To Live In The United States Based On Natural Disasters, Joshua Alpers, Luke Kevan, Santiago Tovar

Engineering Applications of GIS - Laboratory Exercises

This laboratory assignment simulates the most dangerous places to live in the United States based on natural disasters. The natural disasters that will be used in this assignment include wild fires, earthquakes, landslides, hurricanes, tornadoes, and flooding. These inputs will be required in creating a heat map of the United States showing what locations are most likely to have a high probability of natural disasters.

Go to article

Laboratory Exercise – Ideal Locations For A Family, Benjamin Barrett, Colin Esplin, Chris Garcia Jan 2016

Laboratory Exercise – Ideal Locations For A Family, Benjamin Barrett, Colin Esplin, Chris Garcia

Engineering Applications of GIS - Laboratory Exercises

Upon the successful completion of a college degree, many students (and their families) are offered job positions in various locations throughout the Unites States. As a result, these young families are tasked with the challenge of finding a suitable place to live in an area they are completely unfamiliar with. By using a model in ArcMap this task can be made much easier. In this lab a model will be created in ArcGIS Model Builder along with a corresponding map showing suitable locations.

Go to article

Final Laboratory Project – Emergency Landing Site Map, John Chadwick, Daniel Pope, Todd Weichers Jan 2016

Final Laboratory Project – Emergency Landing Site Map, John Chadwick, Daniel Pope, Todd Weichers

Engineering Applications of GIS - Laboratory Exercises

Utah County is constantly developing and expanding. New developments require new roads, new power lines, and changes to existing topography. GIS data is maintained and made available for the state of Utah by Utah AGRC (Automated Geographic Reference Center). GIS can be used to make an easy to update map that will display the current situation of roads, power lines, population density, and terrain. In this exercise a model will be created that will execute to create a map that will display safe emergency landing sites for recreational aircraft in Utah County.

Go to article

Laboratory Exercise – Determining Evacuation Route For Deer Creek Dam Failure, Eleise Hinton, Matt Randall, Brian Packer Jan 2016

Laboratory Exercise – Determining Evacuation Route For Deer Creek Dam Failure, Eleise Hinton, Matt Randall, Brian Packer

Engineering Applications of GIS - Laboratory Exercises

Deer Creek Reservoir holds a volume of approximately 153,000 acre-ft of water. All of this water is held back by Deer Creek dam. Below the dam, the Provo River flows through Provo Canyon and down into Provo before terminating at Utah Lake. While the chance of a dam break is considered unlikely, an extreme event such as a major earthquake could trigger a break. In the case of a dam break, residents of Provo who live in the flood path will need to know where to evacuate. This exercise will create a model to show the nearest evacuation sites for …

Go to article

Laboratory Exercise — Safety On Roads, Elise Estep, Kyungmin Kim, Danielle Nixon Jan 2016

Laboratory Exercise — Safety On Roads, Elise Estep, Kyungmin Kim, Danielle Nixon

Engineering Applications of GIS - Laboratory Exercises

In transportation study area, safety is a great issue. GIS is appropriate to perform spatial analysis the accident history in define area. Specifically, GIS allow researchers to find an area or road segment that have high probability of any type of car accident such as Vehicle to Vehicle, Vehicle to Pedestrian, and Vehicle to Bicycle.

Go to article

Final Laboratory Project - Finding The Ideal Camping Location In The Uintas, Jeffrey Baker, Josh Curtis, Ryan Egbert Jan 2016

Final Laboratory Project - Finding The Ideal Camping Location In The Uintas, Jeffrey Baker, Josh Curtis, Ryan Egbert

Engineering Applications of GIS - Laboratory Exercises

GIS is used extensively by the United States Forest Service in mapping and research. Many resources are available online including raster data and shapefiles. The use of GIS tools allows for analyzing entire forests and finding specific points within large areas that meet certain criteria. The Ashley National Forest, High Uinta Mountains Wilderness, in northeastern Utah contains many shapefiles including roads, forest, highway, points of interest, lakes, streams, etc. The purpose of this lab is to use these available datasets to identify ideal locations to set up camp in the Uinta Mountains.

Go to article

Child Safety Near Pot Shops In Denver, Jacob Flansberg, Elise Jackson, Amelia Theobald Jan 2016

Child Safety Near Pot Shops In Denver, Jacob Flansberg, Elise Jackson, Amelia Theobald

Engineering Applications of GIS - Laboratory Exercises

Some major factors in deciding where one’s family should live include relative safety of the neighborhood, available green space such as parks and schools, grocery stores, and other commercial retail in the area. With the legalization of marijuana in states such as Colorado, proximity of these marijuana dispensaries has become another factor. The Normalized Difference Vegetation Index (NDVI) can be used as a measure of vegetation, and to determine areas with high levels of irrigated vegetation. Using ArcGIS Modelbuilder, the data from an NDVI analysis can be used to determine the proximity of marijuana shops to these types of greenspaces …

Go to article

Use Of Personality Profile Assessments In The Construction Industry, Brian Richard Childs Dec 2015

Use Of Personality Profile Assessments In The Construction Industry, Brian Richard Childs

Theses and Dissertations

Various industries are using personality profile assessments as tools to help reduce employee turnover. Employee turnover is a continuing challenge in the construction industry that has negative effects on construction companies. Research found that it was difficult to know if companies in the construction industry are using personality profile assessments as a tool to help reduce employee turnover. After understanding that other industries were using personality profile assessments in their hiring, promoting, team building and leadership development to reduce turnover, it was desired to understand if the construction industry was doing the same. This research performed a survey among the …

Go to article

A Pilot Study To Determine The Performance Of Tension Lap Splices In Reinforced Masonry Made With Light-Weight Grout, Brandon Richard Corbett Dec 2015

A Pilot Study To Determine The Performance Of Tension Lap Splices In Reinforced Masonry Made With Light-Weight Grout, Brandon Richard Corbett

Theses and Dissertations

The use of light-weight building materials in modern construction has resulted in efficient designs and considerable cost savings by reducing structural weight and supporting sections. This has only been possible because of many years of research to better understand the properties of the light-weight material, and its structural behaviors. However, light-weight grout is a relatively new building material in reinforced masonry construction and little is known about its structural properties. The main objective of this study was to determine if the use of light-weight grout would impact the performance of reinforcing steel, specifically development length, in masonry construction.The research included …

Go to article

Laboratory Resilient Modulus Measurements Of Aggregate Base Materials In Utah, Kirk David Jackson Dec 2015

Laboratory Resilient Modulus Measurements Of Aggregate Base Materials In Utah, Kirk David Jackson

Theses and Dissertations

The Utah Department of Transportation (UDOT) has fully implemented the Mechanistic-Empirical Pavement Design Guide for pavement design but has been using primarily level-three design inputs obtained from correlations to aggregate base materials developed at the national level. UDOT was interested in investigating correlations between laboratory measurements of resilient modulus, California bearing ratio (CBR), and other material properties specific to base materials commonly used in Utah; therefore, a statewide testing program was needed. The objectives of this research were to 1) determine the resilient modulus of several representative aggregate base materials in Utah and 2) investigate correlations between laboratory measurements of …

Go to article

An Automated Tool For High Resolution Visualization Applied To Transient Watershed Models, Noah Robert Taylor Dec 2015

An Automated Tool For High Resolution Visualization Applied To Transient Watershed Models, Noah Robert Taylor

Theses and Dissertations

Numeric hydrologic models can aid in water resource management by providing predictive simulations of water behavior. As computers become more advanced, the models developed also become more complex using more data to represent larger areas for forecasting hydrologic behavior. Unfortunately, as the simulations use more data, the output often becomes difficult to manage and share without investing time and effort into setting up server environments or decreasing the quality of the output to compensate for an efficient and effective user experience. A proposed solution to facilitate the accessibility of massive hydrologic model output is through the web-based visualization tool developed …

Go to article

Evaluating Long-Term Land Cover Changes For Malheur Lake, Oregon Using Envi And Arcgis, Ryan Joseph Woods Dec 2015

Evaluating Long-Term Land Cover Changes For Malheur Lake, Oregon Using Envi And Arcgis, Ryan Joseph Woods

Theses and Dissertations

Land cover change over time can be a useful indicator of variations in a watershed, such as the patterns of drought in an area. I present a case study using remotely sensed images from Landsat satellites for over a 30-year period to generate classifications representing land cover categories, which I use to quantify land cover change in the watershed areas that contribute to Malheur, Mud, and Harney Lakes. I selected images, about every 4 to 6 years from late June to late July, in an attempt to capture the peak vegetation growth and to avoid cloud cover. Complete coverage of …

Go to article

Shaking Table Testing To Evaluate Effectiveness Of Prefabricated Vertical Drains For Liquefaction Mitigation, Caleb Robert Oakes Dec 2015

Shaking Table Testing To Evaluate Effectiveness Of Prefabricated Vertical Drains For Liquefaction Mitigation, Caleb Robert Oakes

Theses and Dissertations

This study was designed to evaluate the ability of vertical drains to prevent liquefaction and limit associated settlement. Drain performance was investigated using full-scale tests with vertical drains in liquefiable sand using a laminar shear box with acceleration time histories applied at the base. Performance of the sand box with drains in these tests was compared with performance of the sane box without drains in previous tests. The test data was also used to create case histories which can be used for further research and calibration of computer models. Although some investigations regarding vertical drains have been performed with centrifuge …

Go to article

Numerical Analysis Of Passive Force On Skewed Bridge Abutments, Zifan Guo Dec 2015

Numerical Analysis Of Passive Force On Skewed Bridge Abutments, Zifan Guo

Theses and Dissertations

Accounting for seismic forces and thermal expansion in bridge design requires an accurate passive force-deflection relationship for the abutment wall. Current design codes make no allowance for skew effects on passive force; however, large scale field tests indicate that there is a substantial reduction in peak passive force as skew angle increases. A reduction in passive force also reduces the transverse shear resistance on the abutment. The purpose of this study is to validate three-dimensional model using PLAXIS 3D, against large scale test results performed at Brigham Young University and to develop a set of calibrated finite element models. The …

Go to article

Bending Behavior Of Carbon/Epoxy Composite Isobeam Structures, Brandon A. Asay Sep 2015

Bending Behavior Of Carbon/Epoxy Composite Isobeam Structures, Brandon A. Asay

Theses and Dissertations

This research demonstrated the fabrication, flexural testing, and analysis of nominally 5 ft (1.5 m) 6-bay and 10 ft (3 m) 12-bay carbon/epoxy IsoBeam™ structures. The rectangular cross-section was 5 in (12.7 cm) wide by 10 in (25.4 cm) high. The IsoBeam structure is a composite lattice structure that is a geometric derivative of the IsoTruss® structure. Modifying the geometry to yield a rectangular cross-section provides additional applications for these beams as structural elements in buildings, aircraft, vehicles, and other structures. The diameters of the constituent members of the IsoBeam, namely the longitudinal and diagonal members, were sized such that …

Go to article

Evaluating The Security Of Smart Home Hubs, Steven A. Christiaens Aug 2015

Evaluating The Security Of Smart Home Hubs, Steven A. Christiaens

Theses and Dissertations

The goal of this research is to improve the security of smart home hubs by developing a standard against which hubs can be evaluated. This was done by first reviewing existing standards, guides, and collections of best practices. I determined that adapting or extending an existing standard was the best way to proceed. Potential candidates were selected, and after thorough comparison, I chose to extend the OWASP Application Security Verification Standard (ASVS). Extensions were composed of additional security requirements to address smart home hub functionality not covered by the existing requirements of the ASVS. These additional requirements were developed based …

Go to article

A Method For Using Pre-Computed Scenarios Of Physically-Based Spatially-Distributed Hydrologic Models In Flood Forecasting Systems, Herman Guillermo Dolder Aug 2015

A Method For Using Pre-Computed Scenarios Of Physically-Based Spatially-Distributed Hydrologic Models In Flood Forecasting Systems, Herman Guillermo Dolder

Theses and Dissertations

Every year floods are responsible of a significant number of human losses, many of which could be avoided with a broader implementation of flood forecasting systems. Nevertheless, there are still some technological and economic limitations that impede the creation of these systems in many parts of the world. At the core of many flood forecasting systems is a hydrologic model that transforms the weather forecast into a flow forecast. Using real-time modeling for potential floods poses a series of problems: if the model is complex, the computational power required can be significant, and consequently expensive, and if the model is …

Go to article

Lateral Resistance Of Pipe Piles Near 20-Ft Tall Mse Abutment Wall With Strip Reinforcements, Jason James Besendorfer Jul 2015

Lateral Resistance Of Pipe Piles Near 20-Ft Tall Mse Abutment Wall With Strip Reinforcements, Jason James Besendorfer

Student Works

Full scale lateral load testing was performed on four 12.75x0.375 pipe piles spaced at 3.9, 2.9, 2.8, and 1.7 pile diameters behind an MSE wall which was constructed for this research to determine appropriate reduction factors for lateral pile resistance based on pile spacing behind the back face of the wall. The load induced on eight soil reinforcements located at various transverse distances from the pile and at different depths was monitored to determine the relationship between lateral load on the pile and load induced in the reinforcement. Each pile was loaded towards the wall in 0.25 in. increments to …

Go to article

Evaluation Of The Accuracy Of Traffic Volume Counts Collected By Microwave Sensors, David Keali'i Chang Jul 2015

Evaluation Of The Accuracy Of Traffic Volume Counts Collected By Microwave Sensors, David Keali'i Chang

Theses and Dissertations

Over the past few years, the Utah Department of Transportation (UDOT) has developed a system called the Signal Performance Metrics System (SPMS) to evaluate the performance of signalized intersections. This system currently provides data summaries for several performance measures including: 1) Purdue Coordination Diagram, 2) Speed, 3) Approach Volume, 4) Purdue Phase Termination Charts, 5) Split Monitor, 6) Turning Movement Volume Counts, 7) Arrivals on Red, and 8) Approach Delay. There is a need to know the accuracy of the data that are being collected by the Wavetronix SmartSensor Matrix and displayed in the SPMS. The TAC members determined that …

Go to article

Correlation Of Fluorescence Spectroscopy And Biochemical Oxygen Demand (Bod5) Using Regression Analysis, Alexander Tetteh Narteh Jul 2015

Correlation Of Fluorescence Spectroscopy And Biochemical Oxygen Demand (Bod5) Using Regression Analysis, Alexander Tetteh Narteh

Theses and Dissertations

This research uses Regression analysis of fluorescence spectroscopy results to correlate with Biochemical Oxygen Demand (BOD5). Fluorescence spectroscopy was applied to samples taken from seven sample sites in the Provo and Orem waste water treatment plants found in Utah County. A total of 161 samples were collected for this research. 23 samples each were taken from four sites in the Provo waste water treatment plant namely Provo head works, aeration basin, primary filter settlement basin and the Provo effluent basin. The Orem head works, the clarifier and the Orem effluent basin were the three sample sites in the Orem waste …

Go to article

Development Of A Simplified Performance-Based Procedure For Assessment Of Liquefaction Triggering Using Liquefaction Loading Maps, Kristin Jane Ulmer Jul 2015

Development Of A Simplified Performance-Based Procedure For Assessment Of Liquefaction Triggering Using Liquefaction Loading Maps, Kristin Jane Ulmer

Theses and Dissertations

Seismically-induced liquefaction has been the cause of significant damage to infrastructure and is a serious concern in current civil engineering practice. Several methods are available for assessing the risk of liquefaction at a given site, each with its own strengths and limitations. One probabilistic method has been shown to provide more consistent estimates of liquefaction risk and can be tailored to the specific needs of a given project through hazard-targeted (i.e. based on return periods or likelihoods) results. This type of liquefaction assessment is typically called “performance-based,” after the Pacific Earthquake Engineering Research (PEER) Center's performance-based earthquake engineering framework. Unfortunately, …

Go to article

Large-Scale Testing Of Passive Force Behavior For Skewed Bridge Abutments With Gravel And Geosynthetic Reinforced Soil (Grs) Backfills, Amy Fredrickson Jul 2015

Large-Scale Testing Of Passive Force Behavior For Skewed Bridge Abutments With Gravel And Geosynthetic Reinforced Soil (Grs) Backfills, Amy Fredrickson

Theses and Dissertations

Correct understanding of passive force behavior is particularly key to lateral evaluations of bridges because plastic deformation of soil backfill is vital to dissipation of earthquake energy and thermally-induced stresses in abutments. Only recently have studies investigated the effects of skew on passive force. Numerical modeling and a handful of skewed abutment tests performed in sand backfill have found reduced passive force with increasing skew, but previous to this study no skewed tests had been performed in gravel or Geosynthetic Reinforced Soil (GRS) backfills. The goal of this study was to better understand passive force behavior in non-skewed and skewed …

Go to article

A Cloud-Based Gssha Index Map Editor Utility For Watershed Decision Support, Jocelynn Marie Anderson Jul 2015

A Cloud-Based Gssha Index Map Editor Utility For Watershed Decision Support, Jocelynn Marie Anderson

Theses and Dissertations

Preventing damages from flooding is critically important for city managers and planners.Efforts in protecting infrastructure from flooding are often coupled with building hydrologicmodels to provide predictions of what is likely to happen during storm events. As land usechanges, these models must be updated, which is more challenging with sophisticated models. Ateam of researchers from universities in Utah and Wyoming have been developing tools forwater management in the Intermountain West as part of a collaborative NSF research grantcalled CI-WATER. In particular, a free and open source web platform called Tethys has beendeveloped to support the development and hosting of hydrologic web …

Go to article

First Prev Next Last