Civil and Environmental Engineering Commons^™

Effects Of Collision Damage On The Ultimate Strength Of Fpso Vessels, Muhammad Zubair Muis Alie, Dian Ramasari, Taufiqur Rachman, Ristiyanto Adiputra

Makara Journal of Technology

Floating production storage offloading (FPSO) vessels are movable offshore structures. These structures are designed with large dimensions, and their decks are loaded with several types of equipment. During collision damage, the hull and deck parts loaded with equipment are severely affected. Therefore, the ultimate strength of FPSO vessels should be thoroughly checked and evaluated. The objective of the present study is to analyze the ultimate strength of FPSO vessels against collision damage characterized by hogging and sagging under longitudinal bending. The cross section of an FPSO vessel is modeled with elements composed of stiffened and unstiffened plates. The vessel length …

Ionic Conductivity And Electrochemical Properties Of Alginate–Nn4no3-Based Biopolymer Electrolytes For Edlc Application, Norfatihah Binti Mazuki, Nur Muhitul Jalilah Rasali, Bouchta Sahraoui, Ahmad Salihin Samsudin

Makara Journal of Technology

In this work, alginate doped with various contents of ammonium nitrate (NH4NO3) as a solid biopolymer electrolyte (SBE) was prepared via casting by using distilled water as a solvent. Impedance studies on alginate–NH4NO3 SBE films were conducted via impedance spectroscopy. The lowest bulk resistance (Rb) showed that the maximum ionic conductivity of the sample containing 25 wt.% NH4NO3 at ambient temperature (303 K) was 5.56 × 10−5 S cm−1. The temperature dependence of ionic conductivity was evaluated, and results confirmed that electrolytes followed an Arrhenius behavior. The highest conducting sample was fabricated into an electrical double-layer capacitor and characterized in …

Synthesis Of Epoxy Monoethanolamide From Bauhinia Monandra Seed Oil, Adewale Adewuyi, Rotimi A. Oderinde

Makara Journal of Technology

In this study, we synthesized epoxidised monoethanolamide (EMA) from Bauhinia monandra seed oil (BMO) via a simple reaction route. In this process, BMO was transesterified to obtain a mixture of methyl esters, which was subjected to a urea adduct complexation reaction. The unsaturated methyl esters (BME) from the urea adduct complexation reaction were then epoxidised using performic acid produced in situ in a one-pot reaction system. The epoxidised methyl esters were converted to EMA by reacting them with monoethanolamine (1:10). The progression of the reaction was monitored using Fourier transform infrared spectroscopy and proton nuclear magnetic resonance spectroscopy, and the …

Ethylene Carbonate And Polyethylene Glycol As Efficient Plasticizers In Cmc-Pva-Nh4no3-Based Polymer Electrolyte, Noor Saadiah Mohd Ali, Yuki Nagao, Ahmad Salihin Samsudin

Makara Journal of Technology

This study investigated the influence of plasticizers (polyethylene glycol [PEG] and ethylene carbonate [EC]) on the ionic conduction of CMC-PVA-NH4NO3. Blended biopolymer electrolytes (BBEs) based on carboxymethyl cellulose–polyvinyl alcohol (CMC-PVA) doped with ammonium nitrate (NH4NO3) were obtained via casting solution technique incorporated with PEG and EC, which acted as plasticizers. Electrical impedance spectroscopy (EIS) was conducted to evaluate the effect of plasticization on the ionic conduction properties. The ionic conductivity improved from 1.70 × 10−3 S/cm for un-plasticized BBEs to 3.92 × 10−3 S/cm for plasticized BBEs with EC and 3.00 × 10−3 S/cm for plasticized BBEs with PEG. The …

Current Status Of Hydrothermal Treatment For Energy And Material Recovery Toward A Sustainable Post-Consumer Material Cycle, Baskoro Lokahita, Muhammad Aziz, Fumitake Takahashi

Makara Journal of Technology

The demand for energy-efficient and environmentally friendly municipal solid waste (MSW) processing has increased in developing countries. The thermochemical process offers a fast and reliable solution to reutilize or reduce the volume of MSW. Hydrothermal treatment is a novel MSW treatment technology that is compatible with high-moisture-content feedstock. It involves the thermal degradation of MSW in pressurized water or steam, which promotes the disintegration of cellulosic and polymer materials. Recent advances have shown effective MSW conversion into homogenous solid hydrochar with higher energy density. Alkali and chlorine content, which causes issues in combustors, was successfully removed due to the washing …

Liquefaction Potential Analysis Based On Nonlinear Ground Response On The Coastline Of Bengkulu City, Indonesia, Lindung Zalbuin Mase

Makara Journal of Technology

This paper presents the study of the seismic response and liquefaction potential of the coastal area of Bengkulu City during the September 2007 Sumatra earthquake. The study is conducted by collecting site investigation data (standard penetration test) and applying input motion to observe soil response. Synthetic ground motion is generated by considering the important aspects of earthquakes, including focal depth, epicenter, earthquake source, and site classification. The synthetized ground motion is then used as the input motion in the seismic response analysis. The results of this analysis are spectral acceleration and peak ground acceleration at each depth. The resulting spectral …

Comparison Of Phytoremediation And Filtration For Diamond-Mine-Tailings Water Treatment, M. Hafidhuddin Noor, Mijani Rahman, Akhmad Gazali, Nia Kania, Aulia Rahma, Erdina L.A. Rampun, Amalia E. Pratiwi, Muthia Elma

Makara Journal of Technology

The water pollution caused by diamond mine activities can kill aquatic life. In this work, we used phytoremediation and filtration to treat pond water polluted by the tailings of a diamond mine located in South Kalimantan, Indonesia. Einchhornia crassipes (water hyacinth) was utilized as the biomass for the phytoremediation process. Gravel (10–15 mm) and sand (0.1–1 mm) were used as filter media in the simple filtration setup, using an up-flow system (bottom to top). In the experiment, 16 L of diamond tailing water was poured into five phytoremediation reactors (each 60 L in volume), which were then tested over seven …

Influence Of Glass Fiber Reinforced Polymer Wraps On Corrosion Progression Of Bridge Piles In Marine Environments, Shayan Yazdani

USF Tampa Graduate Theses and Dissertations

The Friendship Trail Bridge connecting Tampa to St. Petersburg was demolished in 2016. Thirteen 20 inches. by 20 inches. reinforced concrete piles supporting its superstructure were part of research studies conducted between 2004 and 2008 to explore the role of glass fiber reinforced polymers (GFRP) in corrosion repair. During demolition, piles were typically cut at the pile cap and in the splash zone. The resulting segments varied in length between 3 to 4 ft. These remnants were transported to the University of South Florida (USF) campus for postmortem analysis. The overarching goal was to establish the role of GFRP in …

A Novel Self-Healing System: Towards A Sustainable Porous Asphalt, Shi Xu, Xueyan Liu, Amir Tabakovic, Erik Schlangen

Articles

Self-healing asphalt, aimed to produce a sustainable asphalt pavement using green technology, has been studied in the past two decades. Technologies including encapsulated rejuvenator and induction heating have been proposed, demonstrated in the laboratory, and gradually evaluated in field application. This paper looks into the synergy effect of the above two technologies, where induction heating serves as the asphalt damage repair mechanism, requiring just 2 min heating time and encapsulated rejuvenator will replenish (rejuvenate) aged asphalt binder and reinstate bitumen’s healing ability. Moreover, the increased temperature from induction heating could in turn accelerate the diffusion process of rejuvenator into aged …

Architecture And Trilogy Of (Law, Theory And Hypothesis), Ahmed Hashim Hameed

Al-Esraa University College Journal for Engineering Sciences

The general cognitive expositions had focused on the study of the general knowledge frameworks of the field of architecture, with both concepts that influencing and influenced by them, which used to contain them without referring to their intellectual origins in order to understand their general effect and their role in the cognitive enrichment to the architectural field. This, in return, showed the importance of direction to study the role, influence and effect of trilogy (Law, theory and hypothesis) in the field of architecture, according to their general reality knowledge and their specific theoretical and intellectual characteristics. This research deals with …

The Impact Of Spatial Location Of Functions To Identify Architectural Forms As A Landmark (Case Study - Contemporary Islamic Architecture -), Ibtisam Abdulelah Mohammed Al Khafaji, Maha Haki Ismaeil

Al-Esraa University College Journal for Engineering Sciences

This research discusses the impact of spatial location of functions inside architectural form to enhance visual legibility and how it can improve the possibilities of identifying them as a landmark. The absence of a clear conceptual frame which can be used to describe this impact forms the basic research problem. The objective aim of the research is to clarify and describe this impact. To achieve this objective aim, an analytical process was used. We supposed that spatial location of functions enhances visual legibility of forms, then improves our possibility of identifying them as a landmark. For applying the conceptual frame, …

Effect Of Loading Level Of Hybrid Reinforced Concrete Deep Beams Under Repeated Loading, Sawsan Akram Hassan, Ghsoon Ali Faroun

Al-Esraa University College Journal for Engineering Sciences

This research is devoted to investigating the experimental and theoretical behavior of hybrid deep beams under monotonic and repeated two-point loading. The dimensions and the flexural reinforcement of the deep beams were kept constant. In this work, the idea of a hybrid beam is completely different. Two types of concrete were used but not in the cross-section. The first type, which is fiberous concrete (FC), was used in casting beam sides (shear spans), while the second type was conventional concrete (CC) which was used in the middle portion of the beam (between two shear spans). This was done to strengthen …

Reverse Osmosis Method For Sulphate Re-Moval From Treated Wastewater Of Al-Doura Refinery, Rana Mohammed Rasheed

Al-Esraa University College Journal for Engineering Sciences

The treated wastewater by the industrial Wastewater Treatment Plant (WWTP) commonly named (INGECO) in Al-Doura refinery suffers from highly sulfate concentrations that exceed the EPA specified limits of 250 mg/L. Therefore, laboratory water quality historical data have been reviewed and analyzed to determine the annual rate, maximum, and peak sulfate concentrations that were found to be 360 mg/L, 425 mg/L, and 550 mg/L, respectively. Through field inspection aimed at specifying the reasons for the high sulfate concentrations in the wastewater of most refinery process units, it was found that the maximum required sulfate remaining concentration should not exceed 10 mg/L …

Comparison Between Regular And Irregular Configuration In Earthquake Resistant Design, Ali Nur-Aldeen Azeez, Ali Mohsen Jaafer Al-Khafaji

Al-Esraa University College Journal for Engineering Sciences

Earthquake-resistant design is one of the greatest challenges that must be considered by the Architect because it is a serious natural disaster that affects the stability and durability of the building. Due to the connection between the seismic behavior of buildings with its formal configuration and the differences in seismic resistance between regular and irregular buildings, the research problem presented as the confusion of seismic behavior of irregular buildings and their difference from the regular buildings when earthquakes occur. The aim of the research is to clarify the differences between regular and irregular configurations, also clarifying the design considerations in …

Pedestrian Movement Within Residential Areas, Abd Alali Hamza Mohamed

Al-Esraa University College Journal for Engineering Sciences

The network of transport within residential areas, especially within residential neighborhoods, consists mainly of roads designed to provide relative safety for road users and to prioritize solutions that enhance safety. It is believed that the pedestrian movement network should be separated from the car movement network, with a focus on road design, pedestrian paths, and the types of vehicles used in these areas to ensure safety. This research explores the solutions developed in the planning of roads and walkways in traditional housing schemes within the urban fabric of old cities. It examines the approaches and conclusions of modern models of …

Low-Grade Kaolin Clay Natural Resource For Use As A Supplementary Cementitious Material In Structural Concrete Elements, Brandon X. Lorentz

USF Tampa Graduate Theses and Dissertations

At the turn of the century, low-grade kaolin clay (LGK) was presented as a widely available and potential natural resource of supplementary cementitious materials (SCM) for producing high performance concretes. In using LGK as an SCM, clinker production is reduced, aiding environmental concerns with associated CO2 emissions. These types of clays have very heterogeneous mineralogy and microstructural characteristics, causing unique influences on concrete structural and flow performance, although these influences are not well understood. This research studies LGK natural to the state of Florida and assesses their potential use as high performance SCM.

Ten kaolin clays were obtained through a …

Performance Evaluation Of Lightweight Normal And Geopolymer Foamed Concrete Using Palm Oil Fuel Ash As Partial Replacement Of Binder, M .E. Alnahhal Ahmed

Student Works (2020-2029)

Carbon dioxide (CO2) emissions from Ordinary Portland Cement (OPC) have a detrimental effect on the environment and this had led many researchers to search for other alternatives in the form of sustainable cementitious materials. The depletion of natural resources and dumping the industrial by-products and waste materials are serious concern to our environment. This research focusses on the performance of using a palm oil industrial by-product, namely, palm oil fuel ash (POFA), as a partial replacement for OPC and fly ash (FA) in lightweight normal foamed concrete and lightweight geopolymer foamed concrete, respectively. Thus, using 10, 20, and 30% POFA …

Thei Student Applied Research Presentations Sarp 2020, Research Office, Technological And Higher Education Institute Of Hong Kong

THEi Student Applied Research Presentations (SARP)

No abstract provided.

Experimental Study On The Characteristics Of Formation And Dissociation Of Co2 Hydrates In Porous Media, Amin Hosseini Zadeh, Ijung Kim, Seunghee Kim

Department of Civil and Environmental Engineering: Faculty Publications

Geologic carbon sequestration (GCS) has pursued as a feasible strategy to store the large amount of CO₂ to curb its emission to the atmosphere in an effort to mitigate the greenhouse effects. CO₂ hydrate, which can form when the pressure and temperature satisfy its stability condition, can provide a self-trapping mechanism for an offshore CO₂ geologic storage. For example, direct sequestration of CO₂ in the form of hydrate cystals an be achieved in the storage zone an potentially provide a secondary caprock. These application, however, require a thorough understanding of the formation and dissociation of CO …

Macro - And Microstructure Evaluation And Field Applications Of Concrete With Recycled Glass Pozzolan, Marija Krstic

Dissertations and Theses

Concrete is the most used material in the world, second only to water. Conventional concrete is produced with Portland cement (PC). The production of cement is an energy intensive operation that has raised significant environmental concerns, since one ton of cement generates an equal ton of CO₂. In the USA about 90 million tons of cement are used annually, with 3 million tons used in New York. Most contemporary concrete applications for buildings and infrastructure use high-performance concrete (HPC) mixtures which are produced by replacing a percentage of cement with supplementary cementitious materials (SCMs), consisting mainly of fly-ash …

Studying The Effects Of Various Process Parameters On Early Age Hydration Of Single- And Multi-Phase Cementitious Systems, Rachel Cook

Doctoral Dissertations

”The hydration of multi-phase ordinary Portland cement (OPC) and its pure phase derivatives, such as tricalcium silicate (C₃S) and belite (ß-C₂S), are studied in the context varying process parameters -- for instance, variable water content, water activity, superplasticizer structure and dose, and mineral additive type and particle size. These parameters are studied by means of physical experiments and numerical/computational techniques, such as: thermodynamic estimations; numerical kinetic-based modelling; and artificial intelligence techniques like machine learning (ML) models. In the past decade, numerical kinetic modeling has greatly improved in terms of fitting experimental, isothermal calorimetry to kinetic-based modelling …

Time-Dependent Reliability Framework For Durability Design Of Frp Composites, Rajneesh Kumar Bharil

Graduate Theses, Dissertations, and Problem Reports (ETD)

The life-cycle performance, durability, and aging characteristics of Fiber Reinforced Polymer (FRP or Structural Composites) have been of keen interest to the engineers engaged in the FRP design, construction, and manufacturing. Unlike conventional construction materials such as steel and concrete, the design guidelines to account for the aging of FRP are somewhat scattered or not available in an approved or consistent format. Loss of strength over time or aging of any structural material should be of concern to engineers as the in-service lifespan of many engineering structures is expected to exceed 100 years. Use of durability strength-reduction factors or factors …

Strengthening Of Corroded Steel Structures Using Cfrp – An Experimental Review, Ghada El-Mahdy Ph.D., P.Eng, Abdallah H. Yassin, Abdel El Rahman Khaled

Civil Engineering

Fibre reinforced polymers (FRP) have been widely used to strengthen reinforced concrete structures, however, nowadays their use to strengthen steel structures is under investigation. In particular, the need to strengthen corroded steel structures found in aggressive environments, such as marine environments, which have undergone a reduction in cross-sectional area and hence a reduction in their load-carrying capacity is in need of studying. The main problems that arise when using carbon fibre reinforced polymer (CFRP) sheets to strengthen steel structures is the weakness in the interfacial bond between the CFRP and the steel surface, the thinness of CFRP sheet, and the …

Design Of Efficient Carbon-Based Adsorbents For The Removal Of Organic And Inorganic Water Contaminants, Sayedeh Soroosh Mortazavian Dehkordi

UNLV Theses, Dissertations, Professional Papers, and Capstones

Granular activated carbon (AC) and biochar (BC) are two carbon-based adsorbents commonly used for water and wastewater treatment. However, these adsorbents have drawbacks that suppress their aqueous contaminants removal efficiency. Their major disadvantages are that AC has low selectivity and reusability potential, and BC has a hydrophobic nature.

The scope of this dissertation is to enhance the performance of commonly-used carbon-based adsorbents for the removal of organic and inorganic water contaminants and to understand the interactive mechanism of contaminants’ ions/molecules with adsorbents. Hexavalent chromium (Cr(VI)) and trichloroethylene (TCE) are two types of inorganic and organic water contaminants, respectively, which are …

Retrofit Of Corroded Corrugated Metal Culverts Using Gfrp Slip-Liner, Rahulreddy Chennareddy

Civil Engineering ETDs

Culverts are water conveyance structures, typically used to allow water flow and maintain a balance between the flow streams without interrupting structures such as highways and bridges. Corrugated metal pipes (CMPs) have been used as culverts in North America since the 1950s because of their low cost and simple construction method. Today, the corrosion of CMPs is a major problem faced by all U.S. Departments of Transportation. There is an urgent need to provide an efficient solution, one that is corrosion-resistant, to retrofit thousands of corroded CMPs across the country. High specific strength, high strength to weight ratio, corrosion resistance, …

Effect Of Incorporating Pottery And Bottom Ash As Partial Replacement Of Cement, Bassam A. Tayeh, Doha M. Alsaffar, Lawend K. Askar, Asmahan Issa Jubeh

Karbala International Journal of Modern Science

This study addressed the environmental constraints in cement produc­tion. Ordinary Portland cement (OPC) was replaced with pottery powder (PP, produced by grinding locally available pottery) and bottom ash (BA) at 10%, 20% and 30% of cement mass. Moreover, 4% calcium chloride solution (CaCl₂.2H₂O) was used as mixing water. Material properties, such as standard consistency, setting time and compressive strength, were measured with different percentages of OPC replacement with PP and BA. Results indicated that the replacement with PP and BA increased the water demand to achieve the standard consistency. These results revealed that the strength evolution …

A New Synthesized Microalloys Steel Ods Of High Amplitude Ultrasonically Irradiation, Marzuki Silalahi, Hanif Abdurrahman Wicaksana, Ferhat Aziz, Syahfandi Ahda, Mohamad Riza Iskandar

Makara Journal of Technology

Micropowders of oxide-dispersion-strengthened (ODS) steel have been synthesized using the ultrasonic irradiation method with variations in amplitude. The ultrasonic irradiation process is performed for 50 h at a frequency of 20 kHz with 40%, 50%, and 60% amplitudes in toluene solution. The formation of Fe-Cr microalloys in the preparation of Fe- 15Cr-0.5Y2O3 powder was analyzed using SEM-EDS, X-ray diffraction (XRD), and TEM-EDS. The percentage of Fe- Cr phase mass fraction of ODS steel micropowder formed during ultrasonic irradiation with 40%:50%:60% amplitude was 12.2%:34.1%:22.1%, with 25.67:77.02:38.51 nm crystallite size. The crystallite size at 50% amplitude was the largest, and the diffusion …

Comprehensive Inspection On The Experimental Ferritic Stainless Steel By Means Of Transmission Electron Microscopy And Neutron Diffraction Techniques, Parikin Parikin, Mohammad Dani, Riza Iskandar, Aziz Khan Jahja, Andon Insani, Joachim Mayer

Makara Journal of Technology

The field of physical metallurgy is one of the primary beacons that guide alloy developments for multipurpose materials such as the in-core structure materials for pressure vessel components and heat exchangers. The surface microstructure of new ferritic steel with significant local constituent materials was characterized by high resolution powder neutron diffractometer (HRPD) and transmission electron microscope (TEM), combined with the energy dispersive X-ray spectroscopy (EDX). The alloy contains73% Fe, 24% Cr, 2% Si, 0.8% Mn, and 0.1% Ni, in %wt. The charge materials were melted by the casting techniques. The neutron diffractograms obtained shows five dominant diffraction peaks at (110), …

Study On Antibacterial Of Chitosan/Hydroxyapatite Doped Magnesium Composite As A Material For Bone Graft Applications, Andromeda Dwi Laksono, Teodoro A. Amatosa, Jr., Hilda Pebrianti Octaviana Sitorus, Wentika Putri Kusuma Asih, Sulistijono Sulistijono

Makara Journal of Technology

Hydroxyapatite (HAp) is one of the constituent minerals of bone and teeth, that has been widely used for synthesizing bone graft. Due to the limitation on properties of the hydroxyapatite, it is doping with Magnesium (HAp-Mg). The addition of Chitosan (Chi) was expected to improve the antibacterial properties of HAp-Mg. The present research aims to study the influence of Chitosan with 0, 5, 15, and 25 wt% addition on biocompatibility properties of Chi/HAp-Mg composite. HAp-Mg was synthesized using the sol-gel method; meanwhile, Chi/HAp-Mg composite was manufactured by mixing Chitosan in acetic acid, and HAp-Mg was added into the mixture. The …

Evaluation Of Primal-Dual Splitting Algorithm For Mri Reconstruction Using Spatio-Temporal Structure Tensor And L1-2 Norm, Mia Rizkinia, Masahiro Okuda

Makara Journal of Technology

Magnetic resonance imaging (MRI) is an essential medical imaging technique which is widely used for medical research and diagnosis. Dynamic MRI provides the observed object visualization through time and results in a spatiotemporal signal. The image sequences often contain redundant information in both spatial and temporal domains. To utilize this characteristic, we propose a spatio-temporal reconstruction approach based on compressive sensing theory. We apply spatio-temporal structure tensor using nuclear norm, in addition to the wavelet sparsity regularization. The spatio-temporal structure tensor is a matrix that consists of gradient components of the MRI data w.r.t the spatial and temporal domains. For …