Structures and Materials Commons^™

Effects Of Environment On Creep Behavior Of Nextel720/Alumina-Mullite Ceramic Composite With ±45º Fiber Orientation At 1200ºc, Muzaffer Ozer

Theses and Dissertations

The present effort will investigate the off-axis creep behavior of the Nexte720/Alumina-Mullite CMC, a material system which relies on a porous alumina/mullite matrix for damage tolerance as compared to the pure alumina matrix in earlier studies. This research evaluated the creep behavior of N720/AM with a ± 45° fiber orientation at 1200°C in: laboratory air, steam, and argon environments. Creep-rupture tests at the creep stress levels of: 32, 30, 26, and 20 MPa were conducted in each environment. Additionally 35 MPa stress level examined in air and 13 MPa stress level examined both in air and steam. The N720/AM with …

Characterization Of Functionally Graded Materials, Benjamin D. Chapman

Theses and Dissertations

The purpose of this study was to characterize the behavior of a functionally graded material through experimentation and analytical modeling. Functionally graded materials are a ceramic metal composite which transitions from metal on one face to ceramic on the opposite face. Creating reliable models required verifying the material properties. This was accomplished through the use of a static modulus of elasticity test as well as a dynamic ping test. The natural frequencies from the dynamic test were compared with finite element models to determine which material properties most accurately represented the functionally graded material. It was found that the material …

Experimental And Computational Analysis Of Modes In A Partially Constrained Plate, Robert M. Vandawaker

Theses and Dissertations

The field of structural health monitoring (SHM) attempts to reduce labor and cost by allowing technicians to monitor selected properties of an aircraft's structure to detect impending failure. This research examines methods to detect damage to a thermal protection system (TPS) tile using representative 2024-T3 aluminum plates. Plates are subjected to modal analysis in single and joined conditions in an attempt to provide the capability of sensing damage to a tile on the surface of a vehicle while the sensors remain on the superstructure of the airframe. Jointly, the development of a means to model the system using finite element …

Low-Velocity Impact On Composite Sandwich Plates, Eric J. Herup

Theses and Dissertations

The objective of the research is to analytically model the response of composite sandwich plates to low velocity impact. A displacement based, plane stress, finite element code is modified for this purpose. Major new algorithms include 5th order Hermitian interpolation, three dimensional equilibrium integration for transverse stress calculations, sandwich core modeling as an elastic plastic foundation, loading by simulated contact with a spherical indentor, adaptive mesh, damage prediction, damage progression via stiffness reduction, and local-global analysis for displacement. An experimental effort is also included in which composite sandwich plates with graphite epoxy facesheets and Nomex honeycomb core are subjected to …

Fiber Enhanced Viscoelastic Damping Polymers And Their Application To Passive Vibration Control, Houchun Xia

Mechanical & Aerospace Engineering Theses & Dissertations

A new composite damping material is investigated, which consists of a viscoelastic matrix and high elastic modulus fiber inclusions. This fiber enhanced viscoelastic damping polymer is intended to be applied to light-weight flexible structures as surface treatment for passive vibration control. A desirable packing geometry for the composite material is proposed, which is expected to produce maximum shear strain in the viscoelastic damping matrix. Subsequently, a micromechanical model is established in which the effect of fiber segment length and relative motion between neighboring fibers are taken into account. Based on this model, closed form expressions for the effective storage and …

Structural Self-Shadowing And Its Effects On The Thermal-Structural Behavior Of Orbiting Trusses, Jack Mahaney

Mechanical & Aerospace Engineering Theses & Dissertations

The determination of structural shadowing is described. The computation of environmental heat loads for slender structural members in earth orbit is described, and two methods for finite element thermal analysis are described . The effects of self-shadowing on the thermal structural behavior of single truss members and two different trusses are presented. In each case the shadowing produces a noticeable effect on the temperature distributions on truss members, and on the deformations of the trusses.

Curing And Flow Of Thermosetting Resins For Composite Materials Pultrusion, Howard L. Price Jr.

Mechanical & Aerospace Engineering Theses & Dissertations

Fibrous composite materials for mechanical and structural applications often are expensive due to high labor costs. One economical way of making composites is pultrusion, a manufacturing process in which resin-impregnated fibers are pulled at a constant speed through a heated die which shapes the resin-fiber mass and cures the resin. Most of the work which has been done on the process has been of an empirical nature, with limited understanding of the process principles. Most of the experience with pultrusion has been gained with polyester resins and glass fibers. Very little experience has been gained with higher performance, more costly …

Aircraft Quality Casting Standards, Robert Katz, Robert Bolin , Depositor

Robert Katz Publications

These standards are to be used in connection with the Handbook for Instructions for Aircraft Designers, 8^th Edition …

In the radiography of aircraft castings, markings appearing on the film may be attributed to either the condition of the castings examined, or to some details of the radiographic process entirely unrelated to the quality of the castings, These latter patterns must be recognized and related to the radiographic process so that sound castings will not be unnecessarily rejected. Radiographs must be carefully compared with the surface irregularities of the casting they represent before an attempt is made to …