Structures and Materials Commons^™

Characterization Of Laser Deposited Ti-6al-4v To Nb Gradient Alloys, Clincy Cheung

Materials Engineering

An alloy was fabricated with Ti-6Al-4V and Nb powder using laser deposition (LD) to form a compositional gradient. The gradient was deposited, starting with Ti-6Al-4V powder, onto a forged Ti-6Al-4V substrate in an Argon environment. Niobium (Nb) composition increased by 4-at.% with each layer deposited until the composition reached 100-at.% Nb. This process yielded steep thermal gradients and affected the microstructure and mechanical properties across the compositional gradient. To observe the microstructural changes in the alloy, an etched gradient was viewed with optical microscopy at 1000x, where the grain structure was observed to be an acicular α phase at 100-at.% …

A Multi-Scale Based Model For Composite Materials With Embedded Pzt Filaments For Energy Harvesting, A.E. El-Etriby, M.E. Abdel-Meguid, K.M. Shalan, Tarek Hatem, Yehia Bahei-El-Din

Centre for Advanced Materials

Ambient vibrations are major source of wasted energy, exploiting properly such vibration can be converted to valuable energy and harvested to power up devices, i.e. electronic devices. Accordingly, energy harvesting using smart structures with active piezoelectric ceramics has gained wide interest over the past few years as a method for converting such wasted energy. This paper provides numerical and experimental analysis of piezoelectric fiber based composites for energy harvesting applications proposing a multi-scale modeling approach coupled with experimental verification. The multi-scale approach suggested predicting the behavior of piezoelectric fiber-based composites use micromechanical model based on Transformation Field Analysis (TFA) to …

Shape Memory Behavior Of Single Crystal And Polycrystalline Ni-Rich Nitihf High Temperature Shape Memory Alloys, Sayed M. Saghaian

Theses and Dissertations--Mechanical and Aerospace Engineering

NiTiHf shape memory alloys have been receiving considerable attention for high temperature and high strength applications since they could have transformation temperatures above 100 °C, shape memory effect under high stress (above 500 MPa) and superelasticity at high temperatures. Moreover, their shape memory properties can be tailored by microstructural engineering. However, NiTiHf alloys have some drawbacks such as low ductility and high work hardening in stress induced martensite transformation region. In order to overcome these limitations, studies have been focused on microstructural engineering by aging, alloying and processing.

Shape memory properties and microstructure of four Ni-rich NiTiHf alloys (Ni50.3Ti29.7Hf20, Ni50.7Ti29.3Hf20, …

Fiber Length And Orientation In Long Carbon Fiber Thermoplastic Composites, Imad Hanhan, Connor Sullivan, Bhisham Sharma, Michael Sangid

The Summer Undergraduate Research Fellowship (SURF) Symposium

Carbon fiber composites have become popular in aerospace applications because of their lightweight yet strong material properties. The injection molding process can be used to produce discontinuous fiber composites using less time and resources than traditional methods, thereby broadening carbon fiber composites’ applications in different industries. Utilization of longer fibers offers more load carrying capability and superior strength properties for injected molded composites. Since the fiber length and the orientation distribution in Long Fiber Thermoplastics (LFTs) directly affects LFT composites’ material properties, there is a need to study the microstructure of LFTs and characterize fiber length and orientation distributions. Therefore, …

Simulation Of Bio-Inspired Porous Battery Electrodes, Raju Gupta, R. Edwin Garcia, Rui Tu

The Summer Undergraduate Research Fellowship (SURF) Symposium

Advancement of technology has led to the increase in use of electronic devices. However, longer life of the rechargeable battery used in electronic devices is one of the biggest issue and demand in the world of electronic devices at present. Battery's performance is affected by the orientation, arrangement, shape and size, and porosity of the materials out of which battery electrodes are made. The goal of this project is to develop a set of numerical libraries that allow developing material micro structures that will allow increasing the performance of rechargeable batteries. We focused on the development of an algorithm that …

Dynamic Response Of Textile Material Under Transverse Impact, Yuchen Zheng, Matthew C. Hudspeth, Weinong W. Chen

The Summer Undergraduate Research Fellowship (SURF) Symposium

Textile materials, such as Dyneema and Kevlar, are the major raw materials for state of the art military or personal security armor vests. However, in impact experiments, actual observed penetration speed is much lower than theoretically predicted penetration speed. Each armor vest is composed of high performance yarns which are woven together to form fabrics, which when stacked together form a vest. Understanding penetration behavior of yarns is essential to evaluate the performance of fabric, which will be useful for the design of better vests. The project is composed of three parts: static experiments, dynamic yarn experiments and dynamic fabric …

Influence Of Grain Size And Widmanstätten Colonies On Variability Of Tensile Properties Of Forged Ti-6al-4v, Blake T. Gaspar

Master's Theses

When testing forgings for specifications, it was found that some parts did not meet the requirements for mechanical properties. This triggered an investigation into two of the parts from the lot that did not meet specification. The ultimate reason for failure was due to lower than necessary yield strength and ultimate tensile strength values, as well as unwanted variability between regions of the part. Therefore, samples of the regions were tensile tested to determine the differences that existed in yield strength, ultimate tensile strength, and elongation. After tensile testing, quantitative metallography and fractography were conducted to identify aspects of the …

An Investigation Into The Properties And Fabrication Methods Of Thermoplastic Composites, Ann E. Livingston-Peters

Master's Theses

As applications for thermoplastic composites increase, the understanding of their properties become more important. Fabrication methods for thermoplastic composites continually improve to match designs specifications. These advanced thermoplastics have begun to show an improvement in mechanical properties over those found in thermoset composites commonly used in industry. Polyaryletherketones (PEK) have high service temperatures, good mechanical properties, and improved processing capabilities compared to thermoplastics used in the past making them important to the aerospace industry. The wide range of types of PEK make them suitable for a variety of applications, but selection of specific chemistries, processing parameters, and composite stack-ups determine …

Post-Fracture Capacity Of Railroad Flat Car Bridges, Teresa L. Washeleski

Purdue Road School

Railroad flatcars (RRFCs) are a convenient option to replace existing deteriorating bridge structures on low-volume roads. They are typically used as the bridge superstructure by placing two or more flatcars side-by-side to achieve the desired bridge width. Utilizing RRFCs as a bridge allows for rapid construction and greater cost savings compared to traditional practices. These benefits make them an attractive solution for rural communities in Indiana, as well as other states.

Uncertainty remains about the response under higher loads than could be easily achieved in the field and the level of redundancy of railroad flatcar bridges. Using RRFCs as bridges …

Post-Failure Capacity Of Built-Up Steel Members, Matthew H. Hebdon

Purdue Road School

Mechanically fastened built-up steel members have long been known to possess internal member redundancy and, as a result, multiple load paths which can be exploited to increase their functional life. Internal redundancy provides the ability to resist total member failure in the event of a fracture of an individual component. However, there is little experimental data in the literature regarding post-fracture capacity in terms of strength and subsequent fatigue life. The experimental study currently underway will provide needed information on parameters that affect the ability of built- up members to arrest a fracture as well as the available remaining fatigue …

Precipitation, Orientation And Composition Effects On The Shape Memory Properties Of High Strength Nitihfpd Alloys, Emre Acar

Theses and Dissertations--Mechanical and Aerospace Engineering

NiTiHf high temperature shape memory alloys are attractive due to their high operating temperatures (>100 ^oC) and acceptable transformation strain compared to NiTi. However, NiTiHf has limitations due to their lack of ductility and low strength, resulting in poor shape memory properties. In this study, Pd has been added to NiTiHf alloys in an attempt to improve their shape memory behavior. A combined approach of quaternary alloying and precipitation strengthening was used.

The characterization of a Ni_45.3Ti_29.7Hf₂₀Pd₅ (at. %) polycrystalline alloy was performed in compression after selected aging treatments. Transmission electron …

Mode I Fracture Toughness Of Eight-Harness-Satin Carbon Cloth Weaves For Co-Cured And Post-Bonded Laminates, Josh E. Smith

Master's Theses

Mode I interlaminar fracture of 3k 8-Harness-Satin Carbon cloth, with identical fill and weft yarns, pre-impregnated with Newport 307 resin was investigated through the DCB test (ASTM D5528). Crack propagations along both the fill and weft yarns were considered for both post-bonded (co-bonded) and co-cured laminates. A patent-pending delamination insertion method was compared to the standard Teflon film option to assess its applicability to mode I fracture testing. The Modified Beam Theory, Compliance Calibration method, and Modified Compliance Calibration method were used for comparative purposes for these investigations and to evaluate the validity of the proposed Equivalent Stiffness (EQS) method. …

Validation Of Long-Fiber Thermoplastic Composite Models, Christian A. Vuong, Megan Kinney, Michael Sangid

The Summer Undergraduate Research Fellowship (SURF) Symposium

With increased pressure to reduce energy consumption, long-fiber reinforced thermoplastic composites (LFTs) are of interest to aerospace and automotive industries due to their light weight in combination with other desirable mechanical properties and ease of manufacturing to replace common materials such as aluminum and magnesium. However, the performance of LFTs is highly dependent on microstructural variables such as fiber length and orientation, which are heavily influenced by the manufacturing process. Accurately predicting these factors would allow for more rapid advances in LFTs by reducing the experiments needed for certification and decreasing expenses. While models that serve this purpose exist, the …

Fatigue Testing And Data Analysis Of Welded Steel Cruciform Joints, Alina Shrestha

LSU New Orleans Theses and Dissertations

In this study, ABS Publication 115, “Guidance on Fatigue Assessment of Offshore Structures” is briefly reviewed. Emphasis is on the S-N curves based fatigue assessment approach of non-tubular joints, and both size and environment effects are also considered. Further, fatigue tests are performed to study the fatigue strength of load-carrying and non-load-carrying steel cruciform joints that represent typical joint types in marine structures. The experimental results are then compared against ABS fatigue assessment methods, based on nominal stress approach, which demonstrates a need for better fatigue evaluation parameter. A good fatigue parameter by definition should be consistent and should correlate …

The Application Of Advanced Composites For The Construction Of Commercial Transport Aircraft, Mark D. Severson

Graduate Student Works

This individual Capstone project examined and evaluated current industry methods of testing, certification, and maintenance of advanced composite materials for the construction of commercial transport aircraft and the FAA regulations governing their use. The project critically compared and contrasted existing FAA standards and regulations governing the testing, certification, and maintenance of advanced composites for commercial transport aircraft structural applications with current industry practices to determine whether there were any areas of conflict between the two in order to accept or reject that current testing, certification, and maintenance procedures for advanced composites used in primary and secondary commercial transport aircraft structures …

Guided Wave-Based J-Integral Estimation For Dynamic Stress Intensity Factors Using 3d Scanning Laser Doppler Vibrometry, J. Ayers, Christopher Todd Owen, Eric D. Swenson, Anindya Ghoshal, V. Weiss

Faculty Publications

The application of guided waves to interrogate remote areas of structural components has been researched extensively in characterizing damage. However, there exists a sparsity of work in using piezoelectric transducer-generated guided waves as a method of assessing stress intensity factors (SIF). This quantitative information enables accurate estimation of the remaining life of metallic structures exhibiting cracks, such as military and commercial transport vehicles. The proposed full wavefield approach, based on 3D laser vibrometry and piezoelectric transducer-generated guided waves, provides a practical means for estimation of dynamic stress intensity factors (DSIF) through local strain energy mapping via the J-integral. Strain energies …

Investigation Of Astm E 238 Bearing Pin Properties For Various Aerospace Alloys, Trevor J. Lee

Master's Theses

Aircraft are often designed with numbers determined by testing in a lab, rather than by repeatedly building prototypes. These lab tests conform to testing specifications so that the numbers can be compared between manufacturers, suppliers, and lab technicians. One such specification is ASTM specification E238 – 84(08), and it is used to determine important properties of a bearing pin joint like hinges, bolt holes, and rivet joints. The properties determined from this fastener-through-plate method are bearing strength, bearing yield strength, and bearing stiffness.

Adhering to the methods outlined in ASTM E238, a study was performed, looking at the effects that …

Numerical Modeling And Characterization Of Vertically Aligned Carbon Nanotube Arrays, Johnson Joseph

Theses and Dissertations--Mechanical and Aerospace Engineering

Since their discoveries, carbon nanotubes have been widely studied, but mostly in the forms of 1D individual carbon nanotube (CNT). From practical application point of view, it is highly desirable to produce carbon nanotubes in large scales. This has resulted in a new class of carbon nanotube material, called the vertically aligned carbon nanotube arrays (VA-CNTs). To date, our ability to design and model this complex material is still limited. The classical molecular mechanics methods used to model individual CNTs are not applicable to the modeling of VA-CNT structures due to the significant computational efforts required. This research is to …

A Resistance Based Structural Health Monitoring System For Composite Structure Applications, Dennis N. Boettcher

Master's Theses

This research effort explored the possibility of using interwoven conductive and nonconductive fibers in a composite laminate for structural health monitoring (SHM). Traditional SHM systems utilize fiber optics, piezoelectrics, or detect defects by nondestructive test methods by use of sonar graphs or x-rays. However, these approaches are often expensive, time consuming and complicated.

The primary objective of this research was to apply a resistance based method of structural health monitoring to a composite structure to determine structural integrity and presence of defects.

The conductive properties of fiber such as carbon, copper, or constantan - a copper-nickel alloy - can be …

Peridynamic Model For Dynamic Fracture In Unidirectional Fiber-Reinforced Composites, Wenke Hu, Youn Doh Ha, Florin Bobaru

Department of Mechanical and Materials Engineering: Faculty Publications

We propose a computational method for a homogenized peridynamics description of fiber-reinforced composites and we use it to simulate dynamic brittle fracture and damage in these materials. With this model we analyze the dynamic effects induced by different types of dynamic loading on the fracture and damage behavior of unidirectional fiber-reinforced composites. In contrast to the results expected from quasi-static loading, the simulations show that dynamic conditions can lead to co-existence of and transitions between fracture modes; matrix shattering can happen before a splitting crack propagates. We observe matrix–fiber splitting fracture, matrix cracking, and crack migration in the matrix, including …

Feasibility Analysis For Electrically-Powered Hoverboard, Cameron Chan, Jason Cortez, Jay Lopez

Aerospace Engineering

Composite materials are engineered by combining two or more constituent materials with significantly different physical or chemical properties in such a way that the constituents are still distinguishable, and not fully blended. Due to today’s high rising prices of gasoline and aviation fuel costs, many manufacturers have turned to the use of lightweight composites in their designs due to the advantages of the composite material, which include outstanding strength, excellent durability, high heat resistance, and significant weight reduction that the composite material properties hold. The purpose of this project is to design and construct a composite structure for an electrically-powered …

The Effects Of Damage Arrestment Devices In Composite Plate Sandwiches With Fastener Holes, Mark Anderson, Nancy Hung Choy, Lacey Jones, Rita Kourskaya

Aerospace Engineering

Composite materials such as a carbon fiber are used in a variety of new technologies including aircraft, spacecraft, and motor vehicles. Carbon fiber has a high strength to weight ratio, a key advantage over other material options. This report discusses the use of composite damage arrestment devices (DADs) in composite sandwich panels with a foam core. There are three different curing cycles tested for the DADs: pressure only, vacuum only, and vacuum with 1000 lbs of pressure. Using a Tetrahedron Heat Press to cure the composite specimen and an Instron Machine to perform tensile testing, data was collected for each …

Design, Fabrication, Structural Testing, And Numerical Analysis Of A Small Scale Composite Wing, Jacob David Gaunt, Juan Carlos Flores, Vincent Andrew Perry

Aerospace Engineering

A small scale composite wing based on a design found on an experimental aircraft was designed, constructed, and tested dynamically and statically. The wing was constructed similarly to an experimental aircraft wing. The performed static test was intended to produce pure bending. Strain gages were used to measure strains on the wing structure. The strains were converted to stresses to aid in analysis. The static test results suggested that the wing was actually under torsion. Four structural modes were found from the static test. A finite element analysis model was made to compare experimental results to numerical analytical results. The …

Multiscale Transformation Field Analysis Of Progressive Damage In Fibrous Laminates, Yehia Bahei-El-Din, Ritesh Khire, Prabhat Hajela

Centre for Advanced Materials

As part of an ongoing effort to model uncertainty propagation across multiple scales in fibrous laminates, this paper presents a deterministic transformation field analysis for modeling damage progression under membrane forces and bending moments. In this approach, equivalent eigenstresses are computed in the phases and/or plies such that their respective stress components that satisfy the underlying failure criteria are reduced to zero. Superposition of the solutions found for the undamaged laminate under applied loads and under the eigenstress field provide the entire response. Failure criteria are based on stress averages in the fiber and matrix. Damage mechanisms considered are frictional …

Modified Sandwich Structures For Improved Impact Resistance Of Wind Turbine Blades, Yehia Bahei-El-Din, Mostafa Shazly, I. El-Habbal, Y. Elbahy

Centre for Advanced Materials

Wind turbine blades are susceptible to damage due to fatigue as well as impact by flying objects and parts broken off failed blades of nearby wind towers. Localized, permanent compression of the foam core and delamination of the fibrous composite face sheets are typical damage modes and can lead to progressive structural failure. Sandwich structures modified by inclusion of flexible polyurethane (PU) layers within the cross section are examined under both impact and dynamic loads. Finite element models of sandwich structures with conventional and modified designs show that sandwich designs modified with PU interlayes exhibit reduced foam core crushing and …

Studies Of Dynamic Crack Propagation And Crack Branching With Peridynamics, Youn Doh Ha, Florin Bobaru

Department of Engineering Mechanics: Faculty Publications

In this paper we discuss the peridynamic analysis of dynamic crack branching in brittle materials and show results of convergence studies under uniform grid refinement (m-convergence) and under decreasing the peridynamic horizon (δ-convergence). Comparisons with experimentally obtained values are made for the crack-tip propagation speed with three different peridynamic horizons.We also analyze the influence of the particular shape of themicro-modulus function and of different materials (Duran 50 glass and soda-lime glass) on the crack propagation behavior. We show that the peridynamic solution for this problem captures all the main features, observed experimentally, of dynamic crack propagation and branching, as well …

Design And Fabrication Of A Small Prototype Airframe Structure, Kimberly Lynn Clark

UNLV Theses, Dissertations, Professional Papers, and Capstones

This project called for a first-generation prototype aircraft with hovering capabilities that was lightweight. The focus of this study was to design a small low-cost prototype composite airframe that meets specified requirements, analyze structures using finite element analysis and mechanical testing, and construct a prototype using proven composite manufacturing techniques. One fuselage, one wing, and several engine nacelles were designed and fabricated. Several design and fabrication methods and materials were analyzed, with focus given to the nacelles, and recommendations were provided for the manufacture of the first generation airframe based on time, weight, and cost.

Multiscale Modeling Of Impact On Heterogeneous Viscoelastic Solids With Evolving Microcracks, Flavio V. Souza

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Multiscale computational techniques play a major role in solving problems related to viscoelastic composite materials due to the complexities inherent to these materials. In the present work, a numerical procedure for multiscale modeling of impact on heterogeneous viscoelastic solids containing evolving microcracks is proposed in which the (global scale) homogenized viscoelastic incremental constitutive equations have the same form as the local scale viscoelastic incremental constitutive equations, but the homogenized tangent constitutive tensor and the homogenized incremental history dependent stress tensor depend on the amount of damage accumulated at the local scale. Furthermore, the developed technique allows the computation of the …

Non-Destructive Evaluation Of Aerospace Composites, Jeremy D. Johnson

Theses and Dissertations

Five methods of non-destructive material evaluation (NDE) were used to inspect various forms of damage commonly found in aerospace fiberglass composites: voids, edge and sub-surface delaminations, surface burning, and cracking. The images produced by X-ray, X-ray Computed Tomography, terahertz (THz) imaging, ultrasound, and flash IR thermography were analyzed for the detection of defects. Test results and analysis of each NDE method's capabilities provide a comparison study of conventional techniques versus the emerging technology of THz imaging for the non-destructive evaluation of aerospace composite materials. A comparison guide to the five methods' damage detection effectiveness for fiberglass composites is provided by …

Creep And Fatigue Interaction Characteristics Of Pwa1484, Christian J. Pierce

Theses and Dissertations

One of the main methods for predicting the service life of jet engine turbine blades is through creep analysis. A sample of the turbine blade material will be mechanically tested to characterize its creep performance. This characterization will be used to determine safe operating conditions for the material. While methods for modeling creep behavior are generally well developed, this constant load creep testing does not fully represent the loading conditions present in a jet engine due to cyclic loading caused by the mission profile and throttle movements. As the industry seeks to become more accurate in physics based modeling of …