Propulsion and Power Commons^™

Flame-Turbulence Interaction For Deflagration To Detonation, Jessica Chambers

Honors Undergraduate Theses

Detonation is a high energetic mode of pressure gain combustion that exploits total pressure rise to augment high flow momentum and thermodynamic cycle efficiencies. Detonation is initiated through the Deflagration-to-Detonation Transition (DDT). This process occurs when a deflagrated flame is accelerated through turbulence induction, producing shock-flame interactions that generate violent explosions and a supersonic detonation wave. There is a broad desire to unravel the physical mechanisms of turbulence induced DDT. For the implementation of efficient detonation methods in propulsion and energy applications, it is crucial to understand optimum turbulence conditions for detonation initiation. The study examines the role of turbulence-flame …

Rocket Fin Test Fixture Development & Exploration Of Rotation Inducing Fin Design, Ryan A. Saylor Mr., David J. Royak Mr., Jacob P. Byron Mr.

Williams Honors College, Honors Research Projects

The purpose of this senior project was to develop a method of applying rotation inducing rocket fin concepts to rockets for the benefit of the University of Akron Akronauts; the student led rocket design team. The project was performed independently of the team’s current efforts as a research and development endeavor for future team projects. Main project goals were divided into three parts: design a fin test fixture for verification testing in the University’s wind tunnel, develop a parameter-driven software model that could be used to generate design options with theoretical performance data as an output, and run fluid dynamics …

Extending Gr While Moving Up To Supersonic Speeds Poses Challenges Requiring Innovations, Nihad E. Daidzic

Aviation Department Publications

Achieving true global range requires new ideas in lightweight aircraft structures, progress in transonic and supersonic aerodynamics and breakthroughs in low-SFC propulsion.

Axisymmetric Bi-Propellant Air Augmented Rocket Testing With Annular Cavity Mixing Enhancement, Allen A. C. Capatina

Master's Theses

Performance characterization was undertaken for an air augmented rocket mixing duct with annular cavity configurations intended to produce thrust augmentation. Three mixing duct geometries and a fully annular cavity at the exit of the nozzle were tested to enable thrust comparisons. The rocket engine used liquid ethanol and gaseous oxygen, and was instrumented with sensors to output total thrust, mixing duct thrust, combustion chamber pressure, and propellant differential pressures across Venturi flow measurement tubes.

The rocket engine was tested to thrust maximum, with three different mixing ducts, three major combustion pressure sets, and a nozzle exit plane annular cavity (a …

Thrust Prediction For A Rotor Operating In A Ship Airwake, Mathew Thomas

Mechanical & Aerospace Engineering Theses & Dissertations

This report details work performed at Old Dominion University focused on developing a thrust prediction capability for a rotor operating in a ship airwake. The study has built upon previous experimental work utilizing particle image velocimetry-based velocity field measurements to quantify the degree of coupling in a simplified rotor/ship airwake experiment. Using the velocity field data of the previous study, a database was built representing the volume over the landing deck. Rotor thrust was computed using blade element methods and compared to direct load cell measurements and to a superposed velocity field. Results show that the blade element method has …

High Pressure Combustion And Supersonic Jet Ignition For H2/Air, Michael G. Woodworth, Sayan Biswas, Li Qiao

The Summer Undergraduate Research Fellowship (SURF) Symposium

There are many incentives to increase the fuel efficiency of combustion processes. This paper looks at two available options to achieve this goal. The former aims to develop an experimental method that can analyze combustion at extremely high pressures to improve the understanding of high pressure H2/air combustion. Experimental data has been lacking a suitable combustion diagnostic to visualize high pressure combustion processes, making it difficult to improve the process. Improvement of x-ray diffraction tomography in a windowless combustor makes it possible to see flame propagation at high pressure. The procedure and chamber are still in the design phase, yet …

Inlet Shape Considerations For Split-Wing Electric Distributed Propulsion, Kurt Vonderhaar Papathakis

Master's Theses

This thesis aims to uncover preliminary design relationships for an inlet of a split-wing electric distributed propulsion regional airliner. Several aspects of the inlet design were investigated, including: the overall thickness of the airfoil section with respect to the chord, inlet throat area, and lip radius. These parameters were investigated using several angles of attack and mass flow rates through the fan. Computational fluid dynamics, with a 2^nd Order turbulence model was used and validated against World War II era data from NACA, as those studies were the most pertinent wind tunnel data available. Additionally, other works by Boeing, …

A Contribution Toward Better Understanding Of Overbanking Tendency In Fixed-Wing Aircraft, Nihad E. Daidzic

Journal of Aviation Technology and Engineering

The phenomenon of overbanking tendency for a rigid-body, fixed-wing aircraft is investigated. Overbanking tendency is defined as a spontaneous, unbalanced rolling moment that keeps increasing an airplane’s bank angle in steep turns and must be arrested by opposite aileron action. As stated by the Federal Aviation Administration, the overbanking tendency may lead to a loss of control, especially in instrument meteorological conditions. It was found in this study that the speed differential over wing halves in horizontal turns indeed creates a rolling moment that achieves maximum values for bank angles between 45 and 55 degrees. However, this induced rolling moment …

Magnus Effect In Duct Flow, Jesse S. Batko, Cameron W. Clarke, Kenneth W. Smith Jr.

Williams Honors College, Honors Research Projects

The following research paper details the preliminary research carried out by this team. The project was originally conceived to determine if Magnus Lift could be utilized in an unconventional way to assist rockets during takeoff. Several conceptual designs were proposed, but the idea was scrapped when it became apparent that the team would not be able to generate the desired lift without inducing significant amounts of drag and additional weight on a rocket. Instead, the team focused on researching an interesting topic that hasn’t been previously explored: Magnus lift on a cylinder within a duct.

An experimental procedure that could …

Magnus Effect In Duct Flow, Cameron W. Clarke, Jesse S. Batko, Kenneth W. Smith Jr.

Williams Honors College, Honors Research Projects

The following research paper details the preliminary research carried out by this team. The project was originally conceived to determine if Magnus Lift could be utilized in an unconventional way to assist rockets during takeoff. Several conceptual designs were proposed, but the idea was scrapped when it became apparent that the team would not be able to generate the desired lift without inducing significant amounts of drag and additional weight on a rocket. Instead, the team focused on researching an interesting topic that hasn’t been previously explored: Magnus lift on a cylinder within a duct. An experimental procedure that could …

Identification Of Hydrodynamic Forces Developed By Flapping Fins In A Watercraft Propulsion Flow Field, Erdem Aktosun

LSU New Orleans Theses and Dissertations

In this work, the data analysis of oscillating flapping fins is conducted for mathematical model. Data points of heave and surge force obtained by the CFD (Computational Fluid Dynamics) for different geometrical kinds of flapping fins. The fin undergoes a combination of vertical and angular oscillatory motion, while travelling at constant forward speed. The surge thrust and heave lift are generated by the combined motion of the flapping fins, especially due to the carrier vehicle’s heave and pitch motion will be investigated to acquire system identification with CFD data available while the fin pitching motion is selected as a function …

Cold Flow Performance Of A Ramjet Engine, Harrison G. Sykes

Master's Theses

The design process and construction of the initial modular ramjet attachment to the Cal Poly supersonic wind tunnel is presented. The design of a modular inlet, combustor, and nozzle are studied in depth with the intentions of testing in the modular ramjet. The efforts undertaken to characterize the Cal Poly supersonic wind tunnel and the individual component testing of this attachment are also discussed. The data gathered will be used as a base model for future expansion of the ramjet facility and eventual hot fire testing of the initial components. Modularity of the inlet, combustion chamber, and nozzle will allow …

Achieving Global Range In Future Subsonic And Supersonic Airplanes, Nihad E. Daidzic Ph.D., Sc.D.

International Journal of Aviation, Aeronautics, and Aerospace

No commercial airplane in service today is able to fly half great-circle distances over the globe and achieve the non-stop or the global range to any antipodal location on Earth. A subsonic jetliner has the optimum cruising speed at Mach numbers approaching the drag divergence Mach number while still preserving relatively high aerodynamic efficiency. Various fuel-flow laws were used to investigate the cruise performance of subsonic and supersonic aircraft. The effect of wind and aircraft weight and how it affects the optimal cruising airspeed was investigated. Of all different operational cruising techniques, the cruise-climb at high Mach numbers is the …

Exploration Of A Computational Fluid Dynamics Integrated Design Methodology For Potential Application To A Wind Turbine Blade, Gaurav Kapoor

Doctoral Dissertations and Master's Theses

The main purpose of this thesis is to conduct a parametric sensitivity study on the blade design of AOC 15/50 wind turbine based on a CFD approach and optimize the blade design for maximizing the power output. The ANSYS® Fluent® flow solver using the k-ω SST turbulence model was validated by simulating the flow over two dimensional airfoils comprising the AOC 15/50 wind turbine blade. The CFD results have shown a considerable agreement with the experimental data for the airfoils. Parametric correlation study and sensitivity analysis were conducted by performing actual flow simulations over the turbine blade using ANSYS® Fluent®. …

Laminar Deflagrated Flame Interaction With A Fluidic Jet Flow For Deflagration-To-Detonation Flame Acceleration, Joseph P. Mcgarry

Mechanical & Aerospace Engineering Theses & Dissertations

The concept of the Pulse Detonation Engine (PDE) has been of interest for centuries. The issue was originally studied to understand flame propagation in mine shafts after explosions due to methane buildup. The flames would travel down the shafts, transitioning to turbulent flames due to the roughness of the shaft walls, and accelerate to detonation, delivering powerful, destructive forces. The potential for efficient energy production was noticed, and the theory behind flame propagation was later applied to developing propulsion systems. Recently, researchers have begun to understand the full potential of PDEs to efficiently produce an immense amount of thrust due …

Microthruster Fabrication And Characterization: In Search Of The Optimal Nozzle Geometry For Microscale Rocket Engines, Katherine L. Fowee, Alina Alexeenko

The Summer Undergraduate Research Fellowship (SURF) Symposium

A major consideration in microsatellite design is the engineering of micropropulsion systems that can deliver the required thrust efficiently with tight restrictions on space, weight, and power. Cold gas thrusters are one solution to the demand for smaller propulsion systems to accommodate the advancements in technology that have allowed for a reduction in the size and thus the cost of satellites. While much research has been done in understanding the flow regimes within these microthrusters, there is a need to understand how different nozzle designs affect microthruster performance. This requires that experimental data be collected on varying nozzles shapes (orifices, …

Evolution Of Perturbations In Flow Field Mechanics, Samantha R. Bell, David Forliti, Nils Sedano, Kriss Vanderhyde

STAR Program Research Presentations

This project explores the stability analysis of a given flow field. Specifically, where the peak disturbance occurs in a flow as this is the disturbance that is most likely to occur. In rocket combustion, it is important to understand where the maximum disturbance occurs so that the mixing of fuel can be stabilized. The instabilities are the results of frequencies in the area surrounding the flow field. The linear stability governing equations are employed to better understand the disturbance. The governing equations for continuity and momentum in the x and y directions are used to form an equation for the …

High-Efficiency Thrust Vector Control Allocation, Jeb S. Orr, Nathan Slegers

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

A generalized approach to the allocation of redundant thrust vector slew commands for multi-actuated launch vehicles is presented, where deflection constraints are expressed as omniaxial or elliptical deflection limits in gimbal axes. More importantly than in the aircraft control allocation problem, linear allocators (pseudoinverses) are preferred for large booster applications to facilitate accurate prediction of the control-structure interaction resulting from thrust vectoring effects. However, strictly linear transformations for the allocation of redundant controls cannot, in general, access all of the attainable moments for which there is a set of control effector positions thatsatisfles the constraints. In this paper, the control …

Advanced Visualization Techniques Of Hot-Jet Combustion Of Lean And Ultra-Lean Substances, Timothy I. Machin, Li Qiao

The Summer Undergraduate Research Fellowship (SURF) Symposium

Research has been conducted on ignition of natural gas as a potential replacement for fossil fuels. A reason natural gas is not widely used and adapted is because of the harmful emissions created when combusted in rich mixtures, but if the gas can be burned at a lean or ultra-lean equivalence ratio, these emissions can be reduced or even eliminated. One method of burning lean and ultra-lean substances is by use of hot-jet ignition. This method ignites the substance near its combustion temperature, reducing the harmful emissions. This method is not yet fully understood, and so research must be done …

Qualitative Methods Used To Develop And Characterize The Circulation Control System On Cal Poly's Amelia, Eric N. Paciano

Master's Theses

The circulation control system onboard Cal Poly's Advanced Model for Extreme Lift and Improved Aeroacoustics was a critical component of a highly complex wind tunnel model produced in order to fulfill the requirements of a NASA Research Announcement awarded to David Marshall of the Aerospace Engineering Department. The model was based on a next generation, 150 passenger, regional, cruise efficient, short take-off and landing concept aircraft that achieved high lift through circulation control wings and over-the-wing mounted engines. The wind tunnel model was 10-ft in span, used turbine propulsion simulators, and had a functioning circulation control system driven from tunnel …

Ramjet Combustion Chamber, Paul Cameron Stone

Aerospace Engineering

A ramjet combustion chamber is designed and some initial assembly fabrication and test completed as a component of a ramjet graduate project for California Polytechnic State University, San Luis Obispo Supersonic Wind Tunnel. The combustor design is driven by a theoretical model created by a Cal Poly graduate student, Harrison Sykes. Temperature, pressure, and fuel flow will be measured.

Design And Fabrication Of A Ramjet Engine, Clinton C. Humphrey

Aerospace Engineering

In this report, the design and fabrication of the inlet to a ramjet engine is described. The inlet utilizes a single ramp and single sided three shock internal compression to slow the airflow from supersonic to subsonic speeds while providing maximum stagnation pressure to the combustor. The optimum angle for the inlet ramp is calculated to be 10° and it decelerates the airflow from Mach 3.3019 to Mach 0.5438. The stagnation pressure increases from 150 psi to 4.67 ksi. The material of the inlet is composed primarily of low carbon mild steel to accommodate the high pressure of the inlet.

Experimental Investigation Of A 2-D Air Augmented Rocket: High Pressure Ratio And Transient Flow-Fields, Josef S. Sanchez

Master's Theses

A 2-D Air Augmented Rocket, the Cal Poly Air Augmented Rocket (CPAAR) Test Apparatus operating as a mixer-ejector was tested to investigate high stagnation pressure ratio and transient flow fields of an ejector. The primary rocket ejector was supplied with high pressure nitrogen at a maximum chamber pressure of 1758 psia and a maximum mass flow rate of 1.4 lb/s. The secondary flow air was entrained from a fixed volume plenum chamber producing pressures as low as 3.3 psia. The maximum total pressure ratio achieved was 221. The original CPAAR apparatus was rebuilt re-instrumented and capability expanded. A fixed volume …

Designing Propulsion Systems For Future Aerospace Applications, Nihad E. Daidzic

Aviation Department Publications

No abstract provided.

Design, Manufacturing And Testing Of An Environmentally-Green Bipropellant Thruster, Alex Bendoyro, Gabriel Sanchez, Erin Stearns, Phillip Takahashi

Aerospace Engineering

This project reviews the design, manufacturing and experimentation process of a green bi-propellant thruster designed to output 5 lbf. The goals were to successfully design, manufacture and test a thruster, while discovering the complications that arise through out the complete design process of a green thruster. The thruster was successfully designed using ideal rocket equations and the design was successfully confirmed using CFD and FEA. Manufacturing of the thruster was fully planned and revealed mild flaws in thruster design. For example some features were not manufacturable to the exact measurements desired. Testing of the engine gave results inconsistent with expected …

Airplane Landing Flare-The Last 5 Seconds, Nihad E. Daidzic

Aviation Department Publications

No abstract provided.

Hybrid Rocket Motor, Zach Arena, Alexander Athougies, Alden Rodulfo

Aerospace Engineering

This project involves the re-design, manufacturing, and testing of the Cal Poly Space System’s 4th iteration of an M-class 98mm hybrid rocket motor. This motor utilizes hydroxyl-terminated polybutadiene as fuel with liquid nitrous oxide as the oxidizer. Modeling and analysis was conducted on a 12 port self-impinging swirl injector and fuel manufacturing to improve performance. Several hot and cold flow tests were conducted to validate the analysis and predict performance values. Test results included two test fires resulting in an average of 212 lbf of thrust for 6 seconds with an Isp of 160 seconds and an average thrust of …

A Three Dimensional Vortex Particle-Panel Code For Modeling Propeller-Airframe Interaction, Jacob S. Calabretta

Master's Theses

Analysis of the aerodynamic effects of a propeller flowfield on bodies downstream of the propeller is a complex task. These interaction effects can have serious repercussions for many aspects of the vehicle, including drag changes resulting in larger power requirements, stability changes resulting in adjustments to stabilizer sizing, and lift changes requiring wing planform adjustments.

Historically it has been difficult to accurately account for these effects at any stage during the design process. More recently methods using Euler solvers have been developed that capture interference effects well, although they don't provide an ideal tool for early stages of aircraft design, …

Numerical Examination Of Flow Field Characteristics And Fabri Choking Of 2d Supersonic Ejectors, Brett G. Morham

Master's Theses

An automated computer simulation of the two-dimensional planar Cal Poly Supersonic Ejector test rig is developed. The purpose of the simulation is to identify the operating conditions which produce the saturated, Fabri choke and Fabri block aerodynamic flow patterns. The effect of primary to secondary stagnation pressure ratio on the efficiency of the ejector operation is measured using the entrainment ratio which is the secondary to primary mass flow ratio.

The primary flow of the ejector is supersonic and the secondary (entrained) stream enters the ejector at various velocities at or below Mach 1. The primary and secondary streams are …

Back-Pressure Effect On Shock-Train Location In A Scramjet Engine Isolator, Richard I. Paek

Theses and Dissertations

The isolator of the scramjet decelerates the incoming high Mach flow to a lower Mach number and stabilizes the flow before it enters the combustor. Because of the unsteady combustion phenomenon and inconsistent completeness of the combustion, pressures within the combustor can vary drastically. These pressure variations can propagate forward and affect the flow field in the isolator - worst case unstarting the inlet. In this research, the shock train location versus the back-pressure is examined experimentally. The back-pressure is artificially created by symmetric (top & bottom) ramps that can close the flow area. Raising/lowering ramps result in higher/lower back-pressure. …