Engineering Commons^™

Optimization Of Conditions For Production Of Mechanically Strong Suckerin Protein Hydrogels, Autumn Furniss

Williams Honors College, Honors Research Projects

Hydrogels are polymer networks with a large water content. Uses include biomedical applications like drug delivery, wound dressing, and more. Current natural hydrogels lack mechanical robustness. Squid ringed teeth (completely protein) have a modulus comparable to thermoplastics; adding this to hydrogels could improve modulus while maintaining biocompatibility.

Three experiments were performed: Hofmeister solubility study, SRT powder additive, and SRT aqueous solution. The first showed that LiCl solution without acetic acid dissolved the most SRT; overall LiCl dissolved more than all others. SRT as a powder additive increased the modulus of the hydrogels, however the error in the measurements make it …

Synthesis And Applications Of Ceramic (Silicon Carbide And Silicon Nitride), Metallic (Cobalt(0)) And Polymeric (Polyurethane) Aerogels, Parwani M. Rewatkar

Doctoral Dissertations

"A new method has been demonstrated for the synthesis of monolithic ceramic and purely metallic aerogels from xerogel powder compacts, and the use of polyurethane aerogels based on cyclodextrins as efficient desiccants.

I. Highly porous ( > 80%) monolithic SiC and Si₃N₄, aerogels were prepared from compressed compacts of polyurea-crosslinked silica xerogel powders. The process is time efficient as solvent-exchange through powders is fast, and energy efficient as it bypasses drying with supercritical fluids. The final ceramic objects were chemically pure, sturdy, with compressive moduli at 37 ±7 MPa and 59 ± 7 MPa, and thermal conductivities …

Near-Field Electrospinning Of A Polymer/Bioactive Glass Composite To Fabricate 3d Biomimetic Structures, Krishna C. R. Kolan, Jie Li, Sonya Roberts, Julie A. Semon, Jonghyun Park, D. E. Day, Ming-Chuan Leu

Biological Sciences Faculty Research & Creative Works

Bioactive glasses have recently gained attention in tissue engineering and three-dimensional (3D) bioprinting because of their ability to enhance angiogenesis. Some challenges for developing biological tissues with bioactive glasses include incorporation of glass particles and achieving a 3D architecture mimicking natural tissues. In this study, we investigate the fabrication of scaffolds with a polymer/bioactive glass composite using near-field electrospinning (NFES). An overall controlled 3D scaffold with pores, containing random fibers, is created and aimed to provide superior cell proliferation. Highly angiogenic borate bioactive glass (13-93B3) in 20 wt.% is added to polycaprolactone (PCL) to fabricate scaffolds using the NFES technique. …

Atomistic Simulations Of Deformation In Metallic Nanolayered Composites, Sixie Huang

Doctoral Dissertations

"The mechanical behavior of Metallic Nanolayered Composites (MNCs) is governed by their underlying microstructure. In this dissertation, the roles of the interlayer spacing (grain size, d) and the intralayer biphase spacing (layer thickness, h) on mechanical response of Cu/Nb MNCs are examined by Molecular Dynamics (MD) simulations. The study of the strength of MNCs show that small changes in both d and h play a profound role in the relative plastic contributions from grain boundary sliding and dislocation glide. The interplay of d and h leads to a very broad transition region from grain boundary sliding dominated flow, where the …

Freeform Extrusion Fabrication Of Advanced Ceramics And Ceramic-Based Composites, Wenbin Li

Doctoral Dissertations

"Ceramic On-Demand Extrusion (CODE) is a recently developed freeform extrusion fabrication process for producing dense ceramic components from single and multiple constituents. In this process, aqueous paste of ceramic particles with a very low binder content ( < 1 vol%) is extruded through a moving nozzle to print each layer sequentially. Once one layer is printed, it is surrounded by oil to prevent undesirable water evaporation from the perimeters of the part. The oil level is regulated just below the topmost layer of the part being fabricated. Infrared radiation is then applied to uniformly and partially dry the top layer so that the yield stress of the paste increases to avoid part deformation. By repeating the above steps, the part is printed in a layer-wise fashion, followed by post-processing. Paste extrusion precision of different extrusion mechanisms was compared and analyzed, with an auger extruder determined to be the most suitable paste extruder for the CODE system. A novel fabrication system was developed based on a motion gantry, auger extruders, and peripheral devices. Sample specimens were then produced from 3 mol% yttria stabilized zirconia using this fabrication system, and their properties, including density, flexural strength, Young's modulus, Weibull modulus, fracture toughness, and hardness were measured. The results indicated that superior mechanical properties were achieved by the CODE process among all the additive manufacturing processes. Further development was made on the CODE process to fabricate ceramic components that have external/internal features such as overhangs by using fugitive support material. Finally, ceramic composites with functionally graded materials (FGMs) were fabricated by the CODE process using a dynamic mixing device"--Abstract, page iv.

Microstructural Evolution Of Zirconium Carbide (Zrcₓ) Ceramics Under Irradiation Conditions, Raul Florez

Doctoral Dissertations

A comprehensive understanding of the microstructural evolution of Zirconium Carbide (ZrC₂) ceramics under irradiation conditions is required for their successful implementation in advanced Gen-IV gas-cooled nuclear reactors. The research presented in this dissertation focusses on elucidating the ion and electron irradiation response of ZrC₂ ceramics. In the first part of the research, the microstructural evolution was characterized for ZrC₂ ceramics irradiated with 10 MeV Au³⁺ ions up to doses of 30 displacement per atom (dpa) at 800 ºC. Coarsening of the defective microstructure, as a function of dose, was revealed by transmission electron microscopy analysis. …

Biomaterials For Bone Regeneration, Youqu Shen

Doctoral Dissertations

"The purpose of this Ph.D. research is to investigate and improve two classes of hydroxyapatite (HA)-based biomaterials for bone repair: calcium phosphate microspheres and bioactive silicate glass scaffolds. These biomaterials were prepared with modified compositions and microstructures and then were evaluated for bone regeneration.

The open HA microspheres with dense convex surfaces and rough and porous concave surfaces were obtained by sectioning closed hollow HA microspheres. Bone regeneration with the open HA microspheres was greater than with the closed HA microsphere at 12 weeks. Hollow biphasic calcium phosphate (BCP) microspheres have been prepared with different fractions of HA and β-TCP …

Bending Response Of Timber Mortise And Tenon Joints Reinforced With Filler-Modules And Frp Gussets, Andrew Robert Pacifico

Graduate Theses, Dissertations, and Problem Reports (ETD)

In 2013, the California Bay Area (CBA) passed a set of ordinances to ensure that their 10,000 plus timber soft-story buildings were prepared for seismic events, through nondestructive evaluation methods. Many property owners are searching for an affordable retrofitting system that will also meet CBA’s new laws focusing on installations by the mandated deadlines in 2020. Over the past three to four decades, Fiber Reinforced Polymer (FRP) composites have found their way into the civil infrastructure sector for rehabilitation. The objective of this study is to evaluate the bending behavior retrofitted mortise and tenon timber joints reinforced with engineered wood …

Design And Development Of An Actuation System For Morphing Flaps, Nate Mcwilliams

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Requalification Of Coated Fabrics Using Chemlok 2332 In Place Of Chemlok 233, Daniel Madler

Williams Honors College, Honors Research Projects

Rubber coated fabrics are an essential component in the deicing systems of the aerospace industry. Adhesives cements are applied to a fabric prior to being pressed into a rubber compound that will adhere to the fabric. The resulting fabric maintains the strength of the fabric with the added benefits of elasticity and compatibility from the rubber compound. UTC Aerospace Systems relies on these coated fabrics to create safe deicers for the aerospace industry. Chemlok 233, a now obsolete primer cement, was used extensively in the coated fabrics used by UTC. Materials testing and performance evaluation allowed for a replacement cement, …

Generator Design: A Study Of Optimized Airflow, Rachel Wattleworth

Williams Honors College, Honors Research Projects

The core goal of this project was to prototype, test, and evaluate a new type of fan for the Safran Electrical & Power air-cooled generators. The idea of a new fan being made for these two generators arose when they were not adhering to design requirements. A base mixed-flow fan was created to test on multiple generators. Upon creating a prototype, it will be tested to prove if it can increase the air flow, decrease temperatures, and increase power and life of the machines. They all proved to be successful and achieve the main objectives for this project. Data such …

Form Stable Phase-Change Materials, Russell Dent, Marjan Kashfipour, Nitin Mehra, Jiahua Zhu

Williams Honors College, Honors Research Projects

This work investigates the use of two different polyols, xylitol (Xyl) and erythritol (Ery), in conjunction with boron nitride (BN) aerogels, for the purpose of creating thermally conductive composites. While the BN filler in Xyl composites achieved a high anisotropic thermal conductivity of up to 4.53 W/m-K at 18.2 weight percent filler loading, they do not exhibit good phase-change material qualities due to a low solidification enthalpy even at low cooling rates. Alternatively, the BN-Ery composites have shown promising results with a solidification enthalpy of 225.14 J/g and a melting enthalpy of 385.84 J/g at a heat rate of 5 …

Uv-Curable Organic-Inorganic Hybrid Polyurethane Coating, Shiyin Yu

Master's Theses and Doctoral Dissertations

This thesis explored a series of organic-inorganic hybrid polyurethane oligomers with varying molecular weights and functional groups (acrylate and/or silane) that were cured with a single ultraviolet (UV) trigger but two photo-initiators. Upon UV irradiation, the free-radical initiator initiated a free-radical reaction for acrylate cross-linking, and the photo-latent base initiated a sol-gel reaction for condensation of the silanes. This study explored the cure extent of both reactions by FTIR for acrylates and silanes and a weight-loss method for silanes as a function of functional group concentration and time. The general film properties were also studied. The results showed that the …

Deformation Correlations And Machine Learning: Microstructural Inference And Crystal Plasticity Predictions, Michail Tzimas

Graduate Theses, Dissertations, and Problem Reports (ETD)

The present thesis makes a connection between spatially resolved strain correlations and material processing history. Such correlations can be used to infer and classify prior deformation history of a sample at various strain levels with the use of Machine Learning approaches. A simple and concrete example of uniaxially compressed crystalline thin films of various sizes, generated by two-dimensional discrete dislocation plasticity simulations is examined. At the nanoscale, thin films exhibit yield-strength size effects with noisy mechanical responses which create an interesting challenge for the application of Machine Learning techniques. Moreover, this thesis demonstrates the prediction of the average mechanical responses …

Reflectivity And Photoemission Electron Microscopy Studies Of Magnetic Heterostructures, Chih-Yeh Huang

Graduate Theses, Dissertations, and Problem Reports (ETD)

When a thin film thickness becomes ultrathin, the magnetic properties of the thin film can be altered, degraded or even lost. The loss of magnetism has been called the magnetic dead layer (MDL). Considering the trend for miniaturization of information storage and other devices, the MDL is a significant challenge for materials science and engineering. La_1-xSr_xMnO₃ (LSMO) with x=0.3 is an excellent model material that exhibits ferromagnetism at room temperature to study the MDL. This dissertation focuses on understanding the MDL in LSMO films on their own and the effect of this dead layer when …

Investigation Of Nano-Ceria Catalyst Infiltration Of Solid Oxide Fuel Cell (Sofc) Electrodes Using Bio-Inspired Catechol Surfactants, Ozcan Ozmen

Graduate Theses, Dissertations, and Problem Reports (ETD)

Development of solid oxide fuel cell (SOFC) electrodes with nano-structured grains can show enhanced power density with high catalytic activity owing to the higher surface area to volume ratio of the particles. However, the addition of nano-particles during the conventional electrode manufacturing process causes inevitable structural changes due to the coarsening of nano-particles at sintering temperatures. Wet impregnation/ infiltration methods are a practical and well-utilized method to form nanoparticles within the porous electrode microstructure of solid oxide fuel cells (SOFC) which requires relatively low calcination temperatures. Critical factors that impact the reduction of the electrode polarization using the nano-catalyst impregnation …

Enhancing The Thermoelectric Performance Of Calcium Cobaltite Ca3co4o9 Through Single And Dual Elements Doping, Cesar Octavio Romo De La Cruz

Graduate Theses, Dissertations, and Problem Reports (ETD)

Worldwide energy consumption losses more than 60% of the energy after its conversion, most of these losses are in the form of waste heat. Therefore, it is a matter of utmost importance to harness waste heat and reutilize this energy source to improve the overall conversion efficiency. Thermoelectric (TE) technology is one of the rising alternatives to harvest the excessive amount of energy lost as waste heat for a better and sustainable energy future. TE materials can utilize waste heat to improve efficiency in the ever-increasing demand for energy by converting a temperature difference directly into electricity due to the …

Exsolved Nanoparticle Decorated Redox Stable Ceramic Anode Material With High Performance For Solid Oxide Fuel Cells, He Qi

Graduate Theses, Dissertations, and Problem Reports (ETD)

The solid oxide fuel cell (SOFC) is an efficient high-temperature device that can directly convert chemical energy to electrical energy. Because of its high efficiency and environmental friendliness, extensive investigations have been made worldwide in past decades. Though broadly used as the anode material for Solid-Oxide Fuel Cells, Ni-YSZ is limited in some practical applications by severe carbon deposition on Ni in hydrocarbon fuels and a significant volume change of Ni-NiO among redox cycling. In order to overcome these problems and achieve excellent performance in the redox environment, a Ni-free ceramic material La_0.5Sr_1.5Fe_1.5Mo_{0.5 …}

Recovery Of Rare Earth Elements (Rees) From Coal Mine Drainage Sludge Leachate, Panpan Ren

Graduate Theses, Dissertations, and Problem Reports (ETD)

Acid mine drainage (AMD) is the primary cause of aquatic habitat loss in the Appalachian Coal Basin and many other mining districts across the U.S. and the world. The objective of this work is to develop a cost-effective and environmentally benign process to treat and recover Rare Earth Elements (REEs) from AMD. Solvent extraction (SX) is one effective way to turn AMD into a commercially viable feedstock for rare earth production.

In this work, SX experiments were conducted on Y-Ca-Mg-Al-HDEHP-n-heptane-HNO3-H2O system to simulate AMD treatment for Yttrium recovery by changing four parameters: pH values, concentration ratio of Yttrium (Y) over …

Engineering Plasmonic Nanostructures For Light Management And Sensing, Sujan Phani Kumar Kasani

Graduate Theses, Dissertations, and Problem Reports (ETD)

The two major global problems are to provide health safety and to meet energy demands for ever growing population on a large scale. The study of light interaction with nanostructures has shown a promising solution in improving the fields of bio-sensor and solar energy devices which addresses above mentioned two major global problems. Nanostructures have tunable physicochemical properties such as light absorption, electrical and thermal properties unlike bulk materials, which gives an advantage in applications like bio-sensing and energy harvesting devices. The development of nanofabrication techniques along with the discovery of Surface Enhanced Raman Scattering (SERS) and Plasmon Enhanced Fluorescence …

Experimental Measurement Of Dielectric Properties Of Powdery Materials Using A Coaxial Transmission Line, Robert Tempke

Graduate Theses, Dissertations, and Problem Reports (ETD)

This study proposes a standard methodology for coaxial dielectric property measurements of powdery materials (1-10GHz) using a coaxial transmission line. Four powdery materials with dielectric constants ranging from 3.5 to 70 (SiO2, Al2O3, CeO2, and TiO2) were experimentally investigated at varying volume loading fractions in a paraffin mixture. A statistically significant number of paraffin heterogeneous-mixtures was synthesized for all dielectric powders. The dielectric properties of the constitutive materials were determined using appropriate mixture equations. The sensitivity of the equations dielectric prediction to volume loading is discussed with guidance on selecting the best mixing equation. It was determined that low volume …

In Situ Measurement Of Fatigue Induced Crack Growth In Inconel 718 Using Direct Current Potential Drop Method, Joel C. Lindsay

Graduate Theses, Dissertations, and Problem Reports (ETD)

With recent advances in air breathable engines comes more extreme temperature environments that engine components must tolerate. During the design of these engines, it is necessary to understand how material fatigue failures occur at these new, higher operating temperatures. In providing understanding, the following fundamental study focuses on the statistical nature of crack jumps (changes in crack length over time) during fatigue in a polycrystalline nickel-based superalloy, Inconel 718 (IN718). In situ measurement of the crack length at several loading conditions were conducted using a direct current potential drop (DCPD) measurement method. Experimental data was collected at six different fatigue …

Carbon Deposition On Ni/Ysz Anode Sofc For Direct Methane Steam Reforming, Haiyang Li

Graduate Theses, Dissertations, and Problem Reports (ETD)

Solid Oxide Fuel Cells (SOFCs) are electrochemical devices that produce electricity directly from oxidizing fuels. Compared to direct combustion of hydrogen to generate power, it has a big advantage in aspects from efficiency and safety when using hydrogen as the fuel of SOFCs. Hydrocarbon reforming is one of the conventional methods to convert natural gas into hydrogen. While considering the difficulty in storage and transportation of hydrogen, we can utilize the supporting materials on the anode side of SOFCs as catalyst to generate hydrogen via hydrocarbon reforming process and pour the hydrogen as fuel into the SOFC system. Ni/YSZ is …

Modeling The Peak Absorption Of Meh-Ppv In Various Solvents Using Density Functional Theory, Corell H. Moore

Theses and Dissertations

Density Functional Theory (DFT) and time-dependent Density Functional Theory (TD-DFT) are powerful tools for modeling orbital energy in conjugated molecules and have been useful tools for research in organic photovoltaics. In this work, DFT is first used to explain the red shift in the absorption spectrum and increased absorption observed in MEH-PPV. Initially, the modeling of the red-shift in the absorption peak of MEH-PPV is studied using Gaussian 03 software with the global hybrid functional B3LYP for exchange-correlation and the 6-31G basis set. DFT and TD-DFT are used to separately study the effects of polymer chain length, carbon-carbon double-bond stretching, …

Toward Improving Ambient Volta Potential Measurements With Skpfm For Corrosion Studies, Corey M. Efaw, Thiago Da Silva, Paul H. Davis, Lan Li, Elton Graugnard, Michael F. Hurley

Materials Science and Engineering Faculty Publications and Presentations

Scanning Kelvin probe force microscopy (SKPFM) is used in corrosion studies to quantify the relative nobility of different microstructural features present within complex metallic systems and thereby elucidate possible corrosion initiation sites. However, Volta potential differences (VPDs) measured via SKPFM in the literature for metal alloys exhibit large variability, making interpretation and application for corrosion studies difficult. We have developed an improved method for referencing SKPFM VPDs by quantifying the closely related work function of the probe relative to an inert gold standard whose modified work function is calculated via density functional theory (DFT). By measuring and tracking changes in …

Au@Tio2 Nanocomposites Synthesized By X-Ray Radiolysis As Potential Radiosensitizers, Maria C. Molina Higgins

Theses and Dissertations

Radiosensitization is a novel targeted therapy strategy where chemical compounds are being explored to enhance the sensitivity of the tissue to the effects of ionizing radiation. Among the different radiosensitizers alternatives, nanomaterials have shown promising results by enhancing tumor injury through the production of free radicals and reactive oxygen species (ROS). In this work, Gold-supported titania (Au@TiO₂) nanocomposites were synthesized through an innovative strategy using X-ray irradiation, and their potential as radiosensitizers was investigated. Radiosensitization of Au@TiO₂ nanocomposites was assessed by monitoring the decomposition of Methylene Blue (MB) under X-ray irradiation in the presence of the nanomaterial. …

Metallic Systems At The Nano And Micro Scale: Bimetallic Nanoparticles As Catalysts And Mcraly Bond Coats In Thermal Barrier Coatings, Kenneth Kane

Theses and Dissertations

The dissertation is split into two parts. The first part will be focused on changes in material properties found at the nanoscale, as miscibility and electronic structure can change significantly with size. The formation of classically-immiscible bimetallic nanoparticles (BNPs) becomes favorable at the nanoscale and novel catalytic properties can emerge from the bimetallic alloying. The formation of alloyed and non-alloyed BNPs is achieved through pulse laser ablation (PLA) and a significant increase in catalytic activity is observed for both. Recently discovered, the increased activity in the non-alloyed BNPs, deemed multicomponent photocatalysis, is examined and the proposed mechanism discussed. The second …

Compositional Analysis Of Cerium And Cesium In Rapid Setting Cement As An Immobilization Agent For Nuclear Waste, Riyadh M. Motny

Theses and Dissertations

A feasibility of rapid setting cement (RSC) as an agent of immobilization for certain elements such as fission products or radioactive materials was explored. Cerium (Ce) and cesium (Cs) have been selected as a surrogate for U and/or Pu and fission products, respectively, in this study in three phases. In Phase I, RSC was evaluated for physical properties (e.g., porosity, density, pH values, etc.) using two groups methods—the cement powder at different concentrations of Ce (2 – 10 wt%) with deionized water (DIW) and artificial seawater (ASW). The results showed that the final setting time and compressive strength of RSC …

Mse Annual Report 2019, Department Of Materials Science And Engineering, Michigan Technological University

Department of Materials Science and Engineering Annual Reports

Table of Contents

• Faculty and Staff News
• Faculty Research
• Student News
• Alumni News
• By the Numbers
• K-12 Outreach

Development Of Castrip Dual Phase Steel, Brenton Allen Hrebec

Masters Theses

“Thermomechanical processing necessary to produce DP 980 steel using CASTRIP hot band was investigated. The resultant steel has an ultimate tensile strength of 1038 MPa, yield strength of 744 MPa, and total elongation of 8.6%. These mechanical properties were achieved by batch annealing the hot band at 649°C for 48 hours and cold rolling to a 20% reduction. The steel was continuously annealed to simulate a galvanization cycle with an intercritical temperature of 810°C. The possibility of improving the texture of the steel by warm rolling under dynamic strain aging conditions was investigated. Dynamic strain aging in the CASTRIP hot …