Engineering Commons^™

Hydrophobically Modified Isosorbide Dimethacrylates As Biomaterials For Bisphenol A Free Dental Fillings, Bilal Marie

Dissertations

Amalgam and Bisphenol A glycerolate dimethacrylate (BisGMA) are the main dental filling materials in use today. Because of the negative perception of amalgam and its lower esthetic appeal, as well as the desire to replace the endocrine disruptor Bisphenol A, which is the building block of BisGMA, there has been a critical need to search for safer alternatives to these dental filling materials.

Isosorbide is a sugar-based molecule generally recognized as safe. It has been extensively studied as a replacement to the Bisphenol A core in various materials. However, isosorbide is extremely hygroscopic, and water uptake in dental fillings causes …

Electro-Chemo-Mechanics Of The Interfaces In 2d-3d Heterostructure Electrodes, Vidushi Sharma

Dissertations

Unique heterostructure electrodes comprising two-dimensional (2D) materials and bulk three dimensional (3D) high-performance active electrodes are recently synthesized and experimentally tested for their electrochemical performance in metal-ion batteries. Such electrodes exhibit long cycle life while they also retain high-capacity inherent to the active electrode. The role of 2D material is to provide a supportive mesh that allows buffer space for volume expansions upon ion intercalation in the active material and establishes a continuous electronic contact. Therefore, the binding strength between both materials is crucial for the success of such electrodes. Furthermore, battery cycles may bring about phase transformations in the …

Experimental And Computational Studies Of Functionalized Carbon Nanotubes For Use In Energy Storage Devices And Membranes, Emine S. Karaman

Dissertations

Electrolytes with good interfacial stability are a crucial component of any electrochemical device. The development of novel gel polymer electrolytes (GEs) with good interface stability and better manufacturability is important for the development of the next generation electrochemical devices. Gel electrolytes are hybrid electrolyte materials, combining benefits of both liquid and solid systems. Compared with liquid and solid electrolytes, GEs open new design opportunities and do not require rigorous encapsulation methods. In this dissertation, studies on functionalized carbon nanotubes (fCNTs) and graphene oxide (GO) doped polyvinyl alcohol (PVA) based gel electrolytes (GEs) are reported. The ionic conductivity and mechanical strength …

Electric-Field-Driven Processes In Multiphase Fluid Systems, Qian Lei

Dissertations

Advantages of using electric fields in miniaturized apparatuses for a wide range of applications are revealed by numerous experimental and theoretical studies over the last several decades as it offers a simple and efficient method for manipulation of multiphase fluid systems. This approach is considered to be especially beneficial for control of boiling processes and colloidal suspensions considered in the presented work.

Boiling. Today's trends for enhancing boiling heat transfer in terrestrial and space applications focus on removal of bubbles to prevent formation of a vapor layer over the surface at a high overheat. In contrast, this dissertation presents a …

Flexible Microfluidic Device With Nonplanar Interdigitated Microelectrodes, Saud Alssaidy

Theses

The lab-on-a-chip concept has improved significantly in recent years to meet global demand for various applications with the advent of new technologies. Much progress has been achieved, but many microfluidic devices still suffer from design limitations in terms of sensitivity and selectivity because they use rigid, fragile substrate materials and conventional electrodes, which do not provide high sensitivity or selectivity and suffer from signal-to-noise ratio issues. This work proposes a novel device architecture that uses flexible, transparent top and bottom layers integrated with (nonplanar interdigitated microelectrodes) to create a sandwich-like flexible substrate base. The top and bottom layers consist of …

New Type Of Lightweight Aggregate For Use In Structural Concrete, Jamal Khatib, Ali Jahami, Oussama Baalbaki, Adel Elkordi

BAU Journal - Science and Technology

This research studied the utilization of municipal solid waste incineration bottom ash (MSWI-BA) in lightweight coarse aggregate (LWC) production. A special method was followed to prepare the new aggregate to fully replace the normal aggregates (NWA) in concrete. The mechanical properties such as compressive strength, tensile strength, and elasticity modulus were investigated for the LWC concrete. Then, two beams were prepared; one from LWC and the other from NWC. The structural performance of beams made up of lightweight aggregates compared to normal aggregates was investigated. The results showed that this type of aggregates led to a 20% reduction in concrete …

Milling Of Inconel 718: An Experimental And Integrated Modeling Approach For Surface Roughness, Sadaf Zahoor, Adeel Shehzad, Muhammad Salman Habib

Mechanical, Automotive & Materials Engineering Publications

Inconel 718, a hard-to-cut superalloy is reputed for having poor machining performance due to its low thermal conductivity. Consequently, the surface quality of the machined parts suffers. The surface roughness value must fall within the stringent limits to ensure the functional performance of the components used in aerospace and bioimplant applications. One doable way to enhance its machinability is the adequate dissipation of heat from the machining zone through efficient and ecofriendly cooling environment. With this perspective, an experimental and integrated green-response surface machiningbased- evolutionary optimization (G-RSM-EO) approach is presented during this investigation. The results are compared with two base-line …

Numerical Investigation On The Effect Of Spectral Radiative Heat Transfer Within An Ablative Material, Raghava S. C. Davuluri, Rui Fu, Kaveh A. Tagavi, Alexandre Martin

Mechanical Engineering Faculty Publications

The spectral radiative heat flux could impact the material response. In order to evaluate it, a coupling scheme between KATS - MR and P1 approximation model of radiation transfer equation (RTE) is constructed and used. A Band model is developed that divides the spectral domain into small bands of unequal widths. Two verification studies are conducted: one by comparing the simulation computed by the Band model with pure conduction results and the other by comparing with similar models of RTE. The comparative results from the verification studies indicate that the Band model is computationally efficient and can be used to …

A Comparison Of Solid Electrolyte Interphase Formation And Evolution On Highly Oriented Pyrolytic And Disordered Graphite Negative Electrodes In Lithium-Ion Batteries, Haoyu Zhu, Joshua A. Russell, Zongtang Fang, Pete Barnes, Lan Li, Corey M. Efaw, Allison Muenzer, Jeremy May, Kailash Hamal, I. Francis Cheng, Paul H. Davis, Eric J. Dufek, Hui Xiong

Materials Science and Engineering Faculty Publications and Presentations

The presence and stability of solid electrolyte interphase (SEI) on graphitic electrodes is vital to the performance of lithium-ion batteries (LIBs). However, the formation and evolution of SEI remain the least understood area in LIBs due to its dynamic nature, complexity in chemical composition, heterogeneity in morphology, as well as lack of reliable in situ/operando techniques for accurate characterization. In addition, chemical composition and morphology of SEI are not only affected by the choice of electrolyte, but also by the nature of the electrode surface. While introduction of defects into graphitic electrodes has promoted their electrochemical properties, how such structural …

Copper Nanoparticles In-Situ Anchored On Nitrogen-Doped Carbon For High-Efficiency Oxygen Reduction Reaction Electrocatalyst, Hui-Fang Yuan, Yue Zhang, Xing-Wu Zhai, Li-Bing Hu, Gui-Xian Ge, Gang Wang, Feng Yu, Bin Dai

Journal of Electrochemistry

Compared with noble metal platinum (Pt)-based catalysts, inexpensive non-noble metal electrocatalysts have attracted extensive attention for oxygen reduction reaction (ORR). Herein, chitosan as a kind of biomass resource rich in nitrogen and carbon was used to prepare nitrogen-doped carbon (N-C) and N-C in-situ anchored by copper nanoparticles (Cu/N-C). The as-obtained N-C and Cu/N-C nanoparticles were successfully used as non-noble eletrocatalysts tested for ORR. Compared with the N-C, the Cu/N-C showed the high surface area of 607.3 m 2·g-1 with the mean pore size of 2.5 nm and the pore volume of 0.40 cm3·g-1. The most positive Gibbs free …

Effect Of Glycol Based Coolant Pollution On Pem Fuel Cells Stack And Recovery Measures, Cong-Yi Zhu, Xiao-Hui Li, Quan-Quan Gan

Journal of Electrochemistry

As the heat conduction medium of fuel cell cooling system, coolant is very important for the thermal management of fuel cell stack. In practical application, coolant leakage into the stack often occurs. Due to the randomness of fault location of components, the location of coolant leakage is uncertain, which may occur on the cathode side or anode side of some or all single cells. The main effects of coolant pollution on fuel cell stack are as follows: the output of open circuit voltage decreases sharply, the consistency of single cells voltage decreases and so on, which seriously affects the normal …

Functional Sulfate Electrolytes Enable The Enhanced Cycling Stability Of Nati2(Po4)3/C Anode Material For Aqueous Sodium-Ion Batteries, Shu-Jin Li, Zhi-Kang Cao, Wen-Kai Wang, Xiao-Han Zhang, Xing-De Xiang

Journal of Electrochemistry

Aqueous sodium-ion batteries show promising application in fields of large-scale storage of intermittent renewable energies owing to the earth-abundant sodium resources and incombustible aqueous electrolytes. Primary factors determining whether they can be commercially utilized are low cost and long lifetime. Among current electrode materials, NASICON-type NaTi₂(PO₄)₃ arouses wide interests as an anode material for aqueous sodium-ion batteries as it offers a high specific capacity, fast Na-transport ability and reasonable working potential, however, suffering from insufficient cycling performance caused by severe dissolution of active materials in traditional aqueous electrolytes. In this work, a functional sulfate electrolyte …

Nitrogen-Sulfur Co-Doped Porous Carbon Preparation And Its Application In Lithium-Sulfur Batteries, Zhao Gui-Xiang, Hafiz Zaki Ahmed Wail, Zhu Fu-Liang

Journal of Electrochemistry

In recent years, lithium-sulfur (Li-S) batteries have been considered as a promising candidate for the next generation of energy storage system due to their ultrahigh theoretical capacity (1675 mAh·g-1) and energy density (2600 Wh·kg-1). However, the practical application of Li-S batteries is seriously limited by their insulating nature of sulfur, the shuttle effect of polysulfides (LiPSs), and volume expansion during charging and discharging. To overcome those disadvantages, one of the commonly methods is to infiltrate sulfur into porous conductive carbon framework, such as porous carbon, hollow carbon spheres, graphene, carbon nanotubes and some composites of the above structures to achieve …

Cyclic Voltammetric Simulations On Batteries With Porous Electrodes, Xue-Fan Cai, Sheng Sun

Journal of Electrochemistry

Lithium-ion batteries (LIBs) are among the most widely used energy storage devices. Whole-cell modeling and simulations of LIBs can optimize the design of batteries with lower costs and higher speeds. The Pseudo-Two-Dimensional (P2D) electrochemical model is among the most famous whole-cell models and widely applied in LIB simulations. P2D model consists of a series of kinetic equations to model Li+/Li diffusion in working/counter electrodes and electrolytes, which are filled in the porous electrodes and separator, and reactions at the interface of electrolyte and active particles. The traditional applications of P2D model, however, are limited to the cases where the current …

Effect Of Aluminum Alloy Surface Modification On Adhesion Of The Modified Polyurethane Coating And Its Corrosion Protective Performance, Xian-Yin Kuang, Shao-Qiang Jin, Yan-Hui Cao, Yan-Mei Zhang, Shi-Gang Dong, Long-Hui Zhu, Li-Wen Lin, Chang-Jian Lin

Journal of Electrochemistry

The ordinary organic coatings on aluminum alloy usually encounter a problem of low adhesion to the substrate, which results in destruction and failure of the long-term protective performance of the anticorrosion systems. The surface modification of aluminum alloy is able to enhance the adhesion of organic coating on aluminum alloys, and to improve their protective performance. In this work, a combined surface modification of anodic oxidation and mussel adhesion protein/CeO₂/3-aminopropyltriethoxysilane composite film (MCA) was developed on the aluminum alloy. The adhesion of modified polyurethane coated on the treated aluminum alloy and its corrosion protective performance were evaluated comprehensively …

Photoelectrochemical Sensing Based On Zr-Mofs For Homocysteine Detection, Wen-Xia Dong, Guang-Ming Wen, Bin Liu, Zhong-Ping Li

Journal of Electrochemistry

Due to the independent form of the light source and detection system, photoelectrochemical (PEC) sensor has the advantages of low background, high sensitivity and simple operation. So far, PEC systems have been widely used in the fields including the actual detection of metal ions, biological antibodies or antigens in environmental pollutants. When the photosensitive material is irradiated by a light source with an energy being equal to or greater than its band gap, electrons (e-) transition occurs from the valence band to the conduction band, leaving a hole (h+), at the same time, the generated electron-hole pair (e-/h+) separate, and …

Structure Analysis Of Pemfc Cathode Catalyst Layer, Rui-Qing Wang, Sheng Sui

Journal of Electrochemistry

The sluggish oxygen reduction reaction (ORR) on the cathode of the proton exchange membrane fuel cell (PEMFC) has always been one of the key factors limiting its commercialization. The optimization of the cathode catalytic layer structure plays an important role in improving fuel cell performance and reducing production costs. In this paper, two different catalysts (platinum nanoparticles (Pt-NPs) and platinum nanowires (Pt-NWs)) were prepared by using catalyst coated substrate (CCS) method. By constructing a double-layer catalytic layer structure, we analyzed the effect of different catalytic layer structures by performing a single cell test. The results showed that the dense platinum …

Formation And Morphological Evolution Of Nanoporous Anodized Iron Oxide Films, Jin-Wei Cao, Nan Gao, Zhao-Qing Gao, Chen Wang, Sheng-Yan Shang, Yun-Peng Wang, Hai-Tao Ma

Journal of Electrochemistry

The preparation of iron oxide films with nanoporous structure by anodization has attracted much attention for its potential applications. However, the formation mechanism of porous structure during anodization is still unclear. In this paper, the composition of anodic current during the formation of nanoporous anodized iron oxide film was analyzed in combination with the current density-potential response (I-V curve) and the derivation of Faraday’s law. The results showed that the anodic current consisted of an ionic current (leading to the migration of ions to form oxide) and an electronic current (leading to the oxygen evolution), and the …

Influence Of Heat Treatment Time On Cathode Material Cr8O21 For Lithium Battery, Jiu-Kang Teng, Qing-Jie Wang, Liang Zhang, Hong-Mei Zhang, Xiao-Tao Chen, Peng Zhang, Jin-Bao Zhao

Journal of Electrochemistry

Chromium oxide (Cr₈O₂₁) cathode material for lithium batteries was synthesized by thermal decomposition of chromium trioxide (CrO₃) at high temperature. The electrochemical properties of chromium oxide depended on the time and temperature during the heat treatment. Pure phase chromium oxide was prepared, and the effects of heat treatment time on the structures and electrochemical properties of Cr₈O₂₁ were systematically studied. The first discharge mechanism of chromium oxide in lithium batteries was explored, and the results were similar to that in lithium-sulfur batteries. The crystal phases and electrochemical properties of the prepared …

Study Of The Thermodynamic Properties Absorbation Sulfur Storage Gas Of Zinc And Copper Industry, Berdiyarov Tilovkabulovich Berdiyarov Dr., Sh. T. Khojiev, S. T. Matkarimov, Sh. Munosibov

Technical science and innovation

The article considers the problems of utilization of industrial gases formed in the production of copper and ore containing sulfur anhydrides. Currently, the composition of process gases entering the gas purification department is approximately 6-7% SO₂, 0.2-0.3% SO₃ and other gases, until sulfuric acid is obtained from these gases, the sulfate is treated in a counter-scheme with 8% sulfate acid. The aim is to first reduce the temperature of the exhaust gases and second to avoid flying components such as as As, F, Se. As a result of the studies, the amount of SO₂ in the …

Temperature-Immune Self-Referencing Fabry–Pérot Cavity Sensors, Hengky Chandrahalim, Jonathan W. Smith

AFIT Patents

A passive microscopic Fabry-Pérot Interferometer (FPI) sensor an optical fiber a three-dimensional microscopic optical structure formed on a cleaved tip of an optical fighter that reflects a light signal back through the optical fiber. The reflected light is altered by refractive index changes in the three-dimensional structure that is subject to at least one of: (i) thermal radiation; and (ii) volatile organic compounds.

Composite Compression Co-Moulding: A Warpage Reduction Investigation, David Knezevic

Electronic Thesis and Dissertation Repository

To accommodate the increasing need for vehicle emission reduction, automotive manufacturers are presently looking at the next generation of lightweight materials. Glass fibre-reinforced thermoplastic composites belong to this group and exhibit mechanical properties that resemble traditional metals but at a reduced weight and with improvements on other characteristics. Unfortunately, they are affected by processing-related warpage, especially when fabricated by means of the Long Fibre-reinforced Thermoplastics – Direct (LFT-D) manufacturing process, a technology that is valuable because of its high throughput and flow lengths. This occurs for many reasons but reinforcing LFT-D with Glass Mat Thermoplastics (GMT) – another material format …

Thermal And Mechanical Numerical Modeling Of Extrusion-Based 3d Printed Reinforced Polymers For Selecting Manufacturing Process Parameters, Sunil Bhandari

Electronic Theses and Dissertations

Extrusion-based 3D printing of thermoplastic polymer composites manufactures parts that have nonhomogenous, orthotropic, and process-dependent macro-scale material properties. As a part of the dissertation, research works were carried out to: • improve the interlayer mechanical properties and reduce the orthotropy, • use experimentally homogenized orthotropic material properties to numerically model the mechanical behavior of the non-homogenous orthotropic 3D printed parts, • create an efficient numerical thermal model to predict the process-dependent thermal history of the 3D printed part, and • aid the manufacturing process by selecting a suitable set of processing parameters based on a simplified sequentially coupled thermomechanical model. …

Characterization Of Material For Composite Automotive Components, Thomas J. Chang

Electronic Thesis and Dissertation Repository

A composite had been widely used for the lightweighting purpose amid increasing environmental concerns. Among composite manufacturing processes, compression molding is widely used for automotive parts. During compression molding, the mold geometry and molding process conditions significantly influence the fiber configuration and the mechanical performance.

Hence, this thesis aims to characterize the microstructural and mechanical properties of the complex shaped composite automotive components: outer seatback and inner seatback. Both parts were compression molded using commercial glass mat thermoplastic sheet with long glass fibers (30mm-50mm) embedded in the polyamide resin. The microstructural characterization results showed that the microstructural properties are influenced …

Study Of Alloy And Process Modifications To Design Hydrogen Resilient High Hardness Steels, William R. Williams

Theses and Dissertations

High hardness steels (HHS) are vulnerable to hydrogen embrittlement, which can lead to rapid degradation of mechanical properties. Improved resistance to hydrogen embrittlement would be beneficial to many industries including construction, automotive, and military. A comparison study was performed to assess the hydrogen susceptibility of select commercially available and in-house designed HHS alloys. Slow strain rate tensile tests, performed with specimens charged with various levels of hydrogen, provided a macroscopic view of the onset of hydrogen embrittlement. Hydrogen permeation and thermal desorption spectroscopy tests determined the uptake and diffusivity of hydrogen through the material. The evaluation of hydrogen susceptibility for …

Predictive Computational Materials Modeling With Machine Learning: Creating The Next Generation Of Atomistic Potential Using Neural Networks, Mashroor Shafat Nitol

Theses and Dissertations

Machine learning techniques using artificial neural networks (ANNs) have proven to be effective tools to rapidly mimic first principles calculations. These tools are capable of sub meV/atom accuracy while operating with linear scaling with respect to the system size. Here novel interatomic potentials are constructed based on the rapid artificial neural network (RANN) formalism. This approach generates precise force fields for various metals that have historically been difficult to describe at the atomic scale. These force fields can be utilized in molecular dynamics simulations to provide new physical insights. The RANN formalism, which is incorporated into a LAMMPS molecular dynamics …

Effects Of Bonding Pressure And Lamina Thickness On Mechanical Properties Of Clt Composed Of Southern Yellow Pine, Cody S. Bates

Theses and Dissertations

This study produced cross-laminated timber panels at a range of four lamina thickness (5/8, 1, 1 1/8, and 1 1/4 inch) and three bonding pressures (50, 125, 200 psi), producing a total of 12 panels for mechanical testing. The goal of this study is to observe how the thickness and pressure trends affect the mechanical properties of CLT. Tests include flatwise bending, flatwise shear, internal-bond, and delamination. Results showed that bending MOE decreases as the panel thickness increases while bonding pressure had no significance. Bending MOR was less significant for the thickness and more significant for pressure compared to the …

Energy Efficient Configuration Or Perforated Solar Screens For Residential Desert Buildings, Rasha Arafa

Archived Theses and Dissertations

In hot arid desert environments, the solar radiation passing through windows increases the cooling loads and energy consumption of buildings. Shading of windows can reduce these loads. External perforated wooden solar screens were traditionally used for windowsâ shading. However, there is a lack in understanding their performance in a quantitative manner and unavailability of scientific means that could be used for developing new efficient designs that suit the harsh desert conditions. This thesis investigates the impact of changing screen configurations such as perforation percentage, depth, perforation openings aspect ratio and reflectivity on the energy loads, hence defining the most efficient …

The Process-Structure-Property-Performance Of Aisi 1020​, Jonathan Wellman, Tate James, Robbie Christman, Brian Broom

ME 4133/6133 Mechanical Metallurgy

AISI 1020 is widely used in many different industries due to its high strength, high ductility, high machinability, and good weldability. AISI 1020 has a number of applications. Low carbon steel can be used on a macroscale to build bridges, and low carbon steel can be used on smaller scales such as Lawnmower blades. Low carbon steel is the material of choice for lawn mower blades because of its ability to bend before it breaks. The ductile attribute of low carbon steel also has many other benefits.

Ti-6al-7nb Utilization In Surgical Implants, Michael O. Fleming

ME 4133/6133 Mechanical Metallurgy

This presentation discusses the processing, structure, properties, and performance of Ti-6Al-7Nb in relation to use as a surgical implant.