Engineering Commons^™

Metallic Systems At The Nano And Micro Scale: Bimetallic Nanoparticles As Catalysts And Mcraly Bond Coats In Thermal Barrier Coatings, Kenneth Kane

Theses and Dissertations

The dissertation is split into two parts. The first part will be focused on changes in material properties found at the nanoscale, as miscibility and electronic structure can change significantly with size. The formation of classically-immiscible bimetallic nanoparticles (BNPs) becomes favorable at the nanoscale and novel catalytic properties can emerge from the bimetallic alloying. The formation of alloyed and non-alloyed BNPs is achieved through pulse laser ablation (PLA) and a significant increase in catalytic activity is observed for both. Recently discovered, the increased activity in the non-alloyed BNPs, deemed multicomponent photocatalysis, is examined and the proposed mechanism discussed. The second …

Compositional Analysis Of Cerium And Cesium In Rapid Setting Cement As An Immobilization Agent For Nuclear Waste, Riyadh M. Motny

Theses and Dissertations

A feasibility of rapid setting cement (RSC) as an agent of immobilization for certain elements such as fission products or radioactive materials was explored. Cerium (Ce) and cesium (Cs) have been selected as a surrogate for U and/or Pu and fission products, respectively, in this study in three phases. In Phase I, RSC was evaluated for physical properties (e.g., porosity, density, pH values, etc.) using two groups methods—the cement powder at different concentrations of Ce (2 – 10 wt%) with deionized water (DIW) and artificial seawater (ASW). The results showed that the final setting time and compressive strength of RSC …

Mse Annual Report 2019, Department Of Materials Science And Engineering, Michigan Technological University

Department of Materials Science and Engineering Annual Reports

Table of Contents

• Faculty and Staff News
• Faculty Research
• Student News
• Alumni News
• By the Numbers
• K-12 Outreach

Development Of Castrip Dual Phase Steel, Brenton Allen Hrebec

Masters Theses

“Thermomechanical processing necessary to produce DP 980 steel using CASTRIP hot band was investigated. The resultant steel has an ultimate tensile strength of 1038 MPa, yield strength of 744 MPa, and total elongation of 8.6%. These mechanical properties were achieved by batch annealing the hot band at 649°C for 48 hours and cold rolling to a 20% reduction. The steel was continuously annealed to simulate a galvanization cycle with an intercritical temperature of 810°C. The possibility of improving the texture of the steel by warm rolling under dynamic strain aging conditions was investigated. Dynamic strain aging in the CASTRIP hot …

Performance Of One-Part And Two-Part Class C Fly Ash-Based Alkali Activated Mortars, Cedric Chani Kashosi

Masters Theses

“Seeking an eco-friendly concrete, researchers have conducted studies to fully replace ordinary Portland cement (OPC) with fly ash (FA) producing alkali-activated concrete (AAC). Results showed better performance of AAC in terms of high early compressive strength, and durability compared to conventional concrete. However, much is still unknown about the behavior of AAC. From the type of materials used, the curing procedure, and long-term strength development of these binders; a thorough investigation is needed in order to fill the existing gap from previous studies and thus make a step forward to the safely use of AAC in the construction industry. The …

Inclusion Engineering In Femnal Steels, Rairu Vaz Penna

Masters Theses

"Low density high Mn and Al steels, or FeMnAl steels, show great promise for military vehicles and automotive applications in which high strength and toughness is a requirement. However, these steels are subject to processing challenges including development of oxide and nitride inclusions during melting and casting as well as a large as-cast grain size and heavy interdendritic segregation. This can lead to non-uniform heat treatment response and cracking during subsequent hot rolling. Adding up to 10%Al lowers the density of these steels by as much as 15%, unfortunately, this also results in large amounts of hard and faceted AlN …

Removal Of Antimony And Bismuth From Copper Electrorefining Electrolyte By Two Proprietary Solvent Extraction Extractants, Andrew Artzer

Masters Theses

"Antimony and bismuth are two of the most problematic impurities in copper electrorefining (ER). Because of this, much research has been done investigating the ways to remove them. Processes that are currently being used industrially include anode additions, liberators, ion exchange (IX), and solvent extraction (SX). Of these, liberators and anode additions are the most common while SX is the least, mostly being used for arsenic removal. There are other methods that have been evaluated, but are not in commercial use. These include the use of various electrolyte additives, and adsorbents such as bentonite clay and heavy metal sulfates.

Two …

Characterization Of The Surface Condition In Aa6061 Resulting From Deep Rolling As A Function Of Common Industrial Parameters, Andrew Kenneth Layer

Masters Theses

"Roller burnishing is widely used in industry to improve the surface finish and fatigue life of components. As weight reduction continues to grow in the automotive and transportation industries, deep rolling can help maintain product performance by mitigating the increase in component stresses resulting from lower weight systems. Deep rolling parameters such as tool, applied angle, feed rate, spindle speeds, and relative tool direction all affect cycle time, product performance, and appearance. The effects of common industrial parameters on the resultant surface roughness and residual stress profiles were studied in this investigation. The samples were manufactured on a CNC lathe …

Direct Polymer Grafting As A Method Of Maintaining The Mechanical Properties Of Cellulose Nanocrystals In The Presence Of Moisture, Mary Elizabeth Breen-Lyles

Graduate Research Theses & Dissertations

Cellulose nanocrystals (CNCs) are a distinctive nanomaterial derived from cellulose, the most abundant natural polymer on Earth, and the primary reinforcing structural component of cellulose fibrils found within the plant cell wall. These nanocrystals exhibit mechanical properties comparable to synthetic aramid fibers but are advantageous as they are biodegradable, renewable, and can be produced sustainably as they are predominantly extracted from naturally occurring cellulosic materials. These qualities make it a sustainable, highly renewable and environmentally friendly material to be used in place of synthetic materials in a variety of applications. With their high surface area to volume ratio, low level …

Studying The Effect Of Vacancies On The Thermal Conductivity Of Metal-Coated Carbon Nanotubes Using Molecular Dynamics Atomistic Simulations, Ravindra Sunil Dhumal

Graduate Research Theses & Dissertations

Breakthroughs in nanotechnology have made it possible for the size of electronic gadgets to be scaled down to micro/nano level. What follows however, is the side effect of high power densities and overheating as the heat dissipation is restricted to very small surface area. Thus, the need of an effective thermal management system is central to these developments. One way to counter this problem is to use Thermal Interface Materials (TIMs) which promote heat transfer between heat source and sink.

Owing to their high thermal conductivity (up to 6000 W/mK), Carbon Nanotubes (CNTs) are thought of as strong candidates for …

The Study Of Scandate Cathode And Its Characterization Under Various Stages Of Processing, Xiaomeng Zhang

Theses and Dissertations--Chemical and Materials Engineering

Scandate cathode under various processing stages: scandia nano-powder, tungsten scandia mix powder, sintered and impregnated pellets, were characterized with techniques that included electron microscopy, EDS, XPS, and work function measurements. The size and shape uniformity of nano-scale scandia particles changed from round to square and polyhedron during heat treatment. Reduction in size and improvement in size uniformity as heat treating temperature increased were observed. When determining the highest Sc coverage, three assessment methods were used and with their combined results, it was concluded that set VII had the highest Sc at%. In the sintered pellets, it was observed with SEM …

Biomass-Derived Activated Carbons For Electrical Double Layer Supercapacitors: Performance And Stress Effect, Wenxin Cao

Theses and Dissertations--Chemical and Materials Engineering

The vigorous development of human civilization has significantly increased the energy consumption in recent years. There is a great need to use renewable energy sources to substitute the depleting traditional fossil fuels, such as crude oil, natural gas and coal. The development of low-cost and high-performance energy storage devices (ESDs) and systems have drawn great attention due to their feasibility as backup power supply and their applications in portable electronics and electric vehicles. Supercapacitors are among the most important ESDs because of their long charging-discharging cycle life, high power capability and a large operating temperature range. In this thesis, high-performance …

Mechanical Properties And Degradation Of High Capacity Battery Electrodes: Fundamental Understanding And Coping Strategies, Yikai Wang

Theses and Dissertations--Chemical and Materials Engineering

Rechargeable lithium ion and lithium (Li) metal batteries with high energy density and stability are in high demand for the development of electric vehicles and smart grids. Intensive efforts have been devoted to developing high capacity battery electrodes. However, the known high capacity electrode materials experience fast capacity fading and have limited cycle life due to electromechanical degradations, such as fracture of Si-based electrodes and dendrite growth in Li metal electrodes. A fundamental understanding of electromechanical degradation mechanisms of high capacity electrodes will provide insights into strategies for improving their electrochemical performance. Thus, this dissertation focuses on mechanical properties, microstructure …

Nanoharvesting And Delivery Of Bioactive Materials Using Engineered Silica Nanoparticles, Md Arif Khan

Theses and Dissertations--Chemical and Materials Engineering

Mesoporous silica nanoparticles (MSNPs) possess large surface areas and ample pore space that can be readily modified with specific functional groups for targeted binding of bioactive materials to be transported through cellular barriers. Engineered silica nanoparticles (ESNP) have been used extensively to deliver bio-active materials to target intracellular sites, including as non-viral vectors for nucleic acid (DNA/RNA) delivery such as for siRNA induced interference. The reverse process guided by the same principles is called “nanoharvesting”, where valuable biomolecules are carried out and separated from living and functioning organisms using nano-carriers. This dissertation focuses on ESNP design principles for both applications. …

The Fabrication And Characterization Of Metal Oxide Nanoparticles Employed In Environmental Toxicity And Polymeric Nanocomposite Applications, Matthew Logan Hancock

Theses and Dissertations--Chemical and Materials Engineering

Ceria (cerium oxide) nanomaterials, or nanoceria, have commercial catalysis and energy storage applications. The cerium atoms on the surface of nanoceria can store or release oxygen, cycling between Ce³⁺ and Ce⁴⁺, and can therefore act as a therapeutic to relieve oxidative stress within living systems. Nanoceria dissolution is present in acidic environments in vivo. In order to accurately define the fate of nanoceria in vivo, nanoceria dissolution or stabilization is observed in vitro using acidic aqueous environments.

Nanoceria stabilization is a known problem even during its synthesis; in fact, a carboxylic acid, citric acid, is …

Magnetotransport In Zrte5 Crystals, Maksim Andreevich Sultanov

Graduate Research Theses & Dissertations

ZrTe5 is a topological material that is predicted to have a strain or temperature induced phase transition from a topological insulator state into a Weyl/Dirac semimetal state. In this study I find that there is insufficient evidence to support the claims for the existence of such a phase transition. I performed magnetoresistivity measurements using a Quantum Design Physical Properties Measurement System (PPMS) to measure the transverse and longitudinal resistivities at various temperatures and different strengths and orientations of the magnetic field. The measurement results were analyzed using OriginPro to determine the carrier mobility and density and to determine the temperature …

A Method For Iron Determination During Copper Electrometallurgy And Its Application To The Calculation Of Current Efficiency, Daniel Pedro Cruz

Open Access Theses & Dissertations

With the objective of developing statistical models that describe iron kinetics under typical copper electrolytes as well as its effects on current efficiency and influence in cathodic and anodic behavior, a detailed electrochemical analysis is done in this work as a contribution to implement hydrometallurgical processes in the refining or winning process to produce high purity copper.

This Thesis evaluates the oxidation-reduction potential (ORP) of the Fe3+/Fe2+ couple in the H2SO4-Fe2(SO4)3-FeSO4-H2O and H2SO4-CuSO4-Fe2(SO4)3-FeSO4-H2O systems, with addition of different copper concentrations and temperatures up to 70°, typically employed in the industry. This study further validates and expands a thermodynamic expression developed …

Processing, Structure And Mechanical Behavior Of Advanced Engineering Steels, Bing Yu

Open Access Theses & Dissertations

The concept of low lattice misfit and high-density of nanoscale precipitates obtained through solution treatment was adopted to obtain ultrahigh strength maraging steel without compromising elongation. An "ultrahigh strength-high toughness" combination was successfully obtained in 19Ni3Mo1.5Ti maraging steel with ultimate strength of ~1858 MPa and static toughness of ~110 MJ·m-3. Maraging steel had extremely high density (2.3Ã?1024 m-3) of nanoscale precipitates with minimum lattice misfit of less than 1% at the solutionization temperature of 820 oC. Two kinds of nanoscale precipitates, namely, η-Ni3(Ti,Mo) and B2-Ni(Mo,Fe) contributed to ultrahigh strength. The size of nanoscale precipitates governed the movement of dislocations, cutting …

Investigating Using Titanium Zirconium Molybdenum For Additively Manufacturing Aerospace Components, Justin Hunter Vanhoose

Open Access Theses & Dissertations

Mankind throughout history has possessed an innate characteristic to explore, migrating to new frontiers.The requirement for this travel is most broadly associated with the need to pursue more resources. Rockets have been used as a means of weapons since the Sung Dynasty in the thirteenth empire and have now been integrated for travel/transport. The sophistication of rocketry and propulsion has reached a level to where it is plausible that mankind will be a multi-planetary species. The space industry has grown significantly with the advancement of the sophistication of these rocket technologies. However, a specific challenge to overcome in the space …

Microstructure Evolution Of Chalcogenide Materials Via Molecular Dynamics, Sharmin Abdullah

Open Access Theses & Dissertations

The properties of a material are defined by its granular microstructure which is determined by its grain evolution and the types of grain boundaries present in the structure. For example, the performance of Cadmium Sulfide/Cadmium Telluride (CdS/CdTe) solar cells can be affected by the presence of grain boundaries which makes the study of grain structure evolution a very important part of solar cell performance optimization. Grain boundary mobilities are important properties in material science and engineering as they determine grain structures under given processing and operating conditions.

In this thesis, several computational tools were used to analyze the formation and …

Comparative Study Of Analytical Models Of The Gruneisen Parameter Of Metals As Function Of Pressure, Celia Garcia Amparan

Open Access Theses & Dissertations

Commonly used Gruneisen parameter (γ) models only hold accurate in limited regimes making them inapplicable for use over wide temperature-pressure conditions. The accuracy of these analytical models of γ and of the thermal expansion of solids are of particular interest as these are considered proxies for quantifying anharmonicity, which may be a significant contribution to the thermal pressure at high temperatures. This work reviews various definitions of γ and their relations to the equations of state and apply them to two simple metals: Tantalum (Ta) and Copper (Cu), for which a high body of experimental data exists. Classical Molecular Dynamics …

Direct Write 3d Printing Of Functional Ceramics, Jorge Angel Diaz

Open Access Theses & Dissertations

Humidity sensors are used in many industries and are important for ensuring quality and safety. Ceramic sensors are preferred because of their quick response time, ability to withstand high temperatures and excellent Chemical and mechanical stability. The manufacturing world has been moving toward additive manufacturing which is a form of synthesizing 3D tangible layer by layer in witch minimal waste is produced. Additive manufacturing also is known as 3D printing has opened new possibilities to design engineers by giving them design freedom and access to the layers of a part to allow embedded sensors. There is a category of ceramics …

Computational Studies On Perovskite-Metallofullerene Interface And Magnetic Properties Of Mn-Based Mixed Olivines, Bethuel Omutiti Khamala

Open Access Theses & Dissertations

Methyl ammonium lead halide (MAPbX3) perovskite based solar cells have recently emerged as promising class of materials for photovoltaic applications with efficiencies reaching over 22%. Designing interfaces with strong binding is vital to developing efficient, high-performing solar cells. Fullerene-based materials are widely employed as efficient electron acceptors and can serve as electron transporting layer in perovskite based solar cells. We have studied interfaces of methyl ammonium lead iodide MAPbI3 with Sc3N@C80 fullerene and Sc3N@C80PCBM fullerene derivate within the density functional formalism. Different surface terminations and orientations of the methyl ammonium are examined for binding of the fullerene layer. Our calculated …

Interlaminar Damage Detection In Composite Materials, Hariharan Rangarajan

Williams Honors College, Honors Research Projects

Using ceramic matrix composites (CMCs) for high-temperature applications in jet engines increases durability and reduces weight and cooling requirements resulting in improved efficiency and fuel savings. Understanding, detecting, and monitoring different types of damage is essential to achieve optimal performance of CMC components. The Direct Current Potential Drop (DCPD) method is a non-destructive technique of estimating damage in composite materials.

DCPD technique works by measuring nodal potential differences when current is flown through the material. Direct current spreading in different woven and laminate composites is modeled to follow a ladder resistor network in which the nodal voltages decrease exponentially as …

Carbon Fiber Monocoque, Dan Brown, Leland Hoffman

Williams Honors College, Honors Research Projects

The University of Akron’s Human Powered Vehicle Team designed a high performing, fully functioning vehicle that is safe, efficient, and practical for the 2018-2019 season. These objectives were the main priorities when it came to the initial stages of designing the vehicle. In addition, the vehicle was designed in accordance with the ASME 2019 Human Powered Vehicle Challenge guidelines to satisfy all the rules and requirements. Additional priorities have been created to teach practical engineering skills and techniques to the students participating in the project through different points in the production process including research, vehicle design, construction, and testing.

The …

Compression Set Improvement Of Thermoplastic Vulcanizates For High Temperature Tubing, Mitchell Valaitis

Williams Honors College, Honors Research Projects

It was hypothesized that increasing the curative level of the fluorocarbon rubber (FKM) used in manufacturing of thermoplastic vulcanizate (TPV) materials would decrease the compression set values of the TPV enough for it to be suitable as a flexible, lightweight alternative to high operating temperature thermoset rubber tubing currently being used for power steering hose. First, promising TPV formulations were identified by varying the polyamide (PA) and FKM used in a Brabender mixer. Four different types of polyamide and four different types of FKM were investigated, with two of the FKM types and one polyamide type identified as being promising. …

Scanning Probe Microscopy Measurements On 2d Materials And Iridates, Armin Ansary

Theses and Dissertations--Physics and Astronomy

In the past two decades, there has been a quest to understand and utilize novel materials such as iridates and two-dimensional (2D) materials. These classes of materials show a lot of interesting properties both in theoretical predictions as well as experimental results. Physical properties of some of these materials have been investigated using scanning probe measurements, along with other techniques.

One-dimensional (1D) catalytic etching was investigated in few-layer hexagonal boron nitride (hBN) films. Etching of hBN was shown to share several similarities with that of graphitic films. As in graphitic films, etch tracks in hBN commenced at film edges and …

Structural Behavior Of Steel Plate Embedded Hybrid Gfrp Shapes, Piyush R. Soti

Graduate Theses, Dissertations, and Problem Reports (ETD)

The civil infrastructure industry has been dominated by traditional materials such as steel, timber, and concrete. Although these materials offer great advantages, they have major durability issues in terms of corrosion, decaying, and cracking. Traditional material-based structures deteriorate frequently and require regular-interval repairs with huge expenditures. To resolve these maintenance and durability issues associated with traditional materials, fiber reinforced polymer (FRP) composites have gained some popularity in the past few decades because of their superior mechanical properties and durability. Carbon-FRPs (CFRPs) and glass-FRP (GFRPs) are the most commonly used FRPs in the market. However, in civil engineering applications, CFRPs are …

A Multiscale Model Of Protein Adsorption On A Nanoparticle Surface, David Power, Ian Rouse, Stefano Poggio, Erik Brandt, Hender Lopez, Alexander Lyubartsev, Vladimir Lobaskin

Articles

We present a methodology to quantify the essential interactions at the interface between inorganic solid nanoparticles (NPs) and biological molecules. Our model is based on pre-calculation of the repetitive contributions to the interaction from molecular segments, which allows us to efficiently scan a multitude of molecules and rank them by their adsorption affinity. The interaction between the biomolecular fragments and the nanomaterial are evaluated using a systematic coarse-graining scheme starting from all-atom molecular dynamics simulations. The NPs are modelled using a two-layer representation, where the outer layer is parameterized at the atomistic level and the core is treated at the …

Rapid Fabrication Of Silver Nanoparticle/Polydopamine Functionalized Polyester Fibers, Yanfen Zhou, Liang Jiang, Ya Guo, Zhenhua Sun, Zhiqing Jiang, Shaojuan Chen, Jianwei Ma, Stephen Jerrams

Articles

In this paper, silver nanoparticles functionalized poly(ethylene terephthalate) (PET) fibers with antimicrobial activity, electrical conductivity and good coating stability are reported. Firstly, silver plated PET fibers were fabricated by rapid polydopamine (PDA) modification followed by electroless plating. Secondly, the surface morphologies and compositions of PDA modified and silver coated PET fibers were characterized by employing scanning electron microscopy, atomic force microscopy, X-ray diffraction and energy dispersive spectrometry. Finally, the antimicrobial properties and electrical conductivity of the silver plated PET fibers were investigated. The results showed that the silver coated PET fibers exhibited excellent antimicrobial activity to both Escherichia coli and …