Open Access. Powered by Scholars. Published by Universities.®

Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Materials Science and Engineering

Institution
Keyword
Publication Year
Publication
Publication Type
File Type

Articles 5791 - 5820 of 16715

Full-Text Articles in Engineering

Verification Of Effectiveness Of Spot-Heating Technique In Reducing Spread Of Weld Lines In Injection Molded Plastic Products, Shah Ashikul Abed Sakar Apr 2020

Verification Of Effectiveness Of Spot-Heating Technique In Reducing Spread Of Weld Lines In Injection Molded Plastic Products, Shah Ashikul Abed Sakar

Masters Theses

In producing a plastic part in an injection molding machine many physical factors related to the machine, such as injection pressure, holding pressure, heater temperature, etc. play their roles in the overall quality of the produced part. There are many aspects of the quality of a plastic part, such as part strength, part dimensions, and part surface finish. If any of those aspects gets compromised, the part is considered to have some defects. Of all defects found in injection-molded plastic parts, one most common defect is the presence of weld lines.Weld lines are formed when the flow of the molten …

Go to article

Effect Of Frother Strength And Solids On Gas Dispersion In A Cavitation Sparger Measured By Electrical Resistance Tomography, Philip Holdsworth Apr 2020

Effect Of Frother Strength And Solids On Gas Dispersion In A Cavitation Sparger Measured By Electrical Resistance Tomography, Philip Holdsworth

Graduate Theses & Non-Theses

Gas dispersion in column flotation is critical for optimizing particle-bubble interaction and maximizing recovery. The effect of various flotation frothers on axial gas dispersion rates in a column flotation cell were measured using electrical resistance tomography (ERT). Tests included two-phase (gas-liquid) and three-phase (gas-liquid-solid) to determine the effect of mechanical parameters and the presence of solids on gas dispersion. Gas holdup can be measured using ERT and utilized in the determination of axial gas dispersion rate in the column. The ERT is constructed with two sensor planes making it possible to simultaneously capture gas holdup values at one cm and …

Go to article

Cellulose Based Separator For High-Performance Lithium-Ion Batteries, Akshit Vaidya Apr 2020

Cellulose Based Separator For High-Performance Lithium-Ion Batteries, Akshit Vaidya

Masters Theses

During the past two decades, lithium-ion batteries (LIBs) have gained great success in the field of portable devices, and currently, are penetrating to the market of vehicles. Compared to the fast development of LIBs, little efforts have been dedicated to the separator, which is one of the most important components of LIBs. Primarily, the lithium-ion battery separator has two functions, one is to prevent direct contact between the positive and negative electrodes, and the other is to provide a path for effective ionic transportation. Currently, the separator market of LIBs is dominated by polyolefin materials such as polypropylene, polyethylene, and …

Go to article

Questaal: A Package Of Electronic Structure Methods Based On The Linear Muffin-Tin Orbital Technique, Dimitar Pashov, Swagata Acharya, Walter R.L. Lambrecht, Jerome Jackson, Kirill Belashchenko, Athanasios Chantis, Francois Jamet, Mark Van Schilfgaarde Apr 2020

Questaal: A Package Of Electronic Structure Methods Based On The Linear Muffin-Tin Orbital Technique, Dimitar Pashov, Swagata Acharya, Walter R.L. Lambrecht, Jerome Jackson, Kirill Belashchenko, Athanasios Chantis, Francois Jamet, Mark Van Schilfgaarde

Kirill Belashchenko Publications

This paper summarises the theory and functionality behind Questaal, an open-source suite of codes for calculating the electronic structure and related properties of materials from first principles. The formalism of the linearised muffin-tin orbital (LMTO) method is revisited in detail and developed further by the introduction of short-ranged tight-binding basis functions for full-potential calculations. The LMTO method is presented in both Green's function and wave function formulations for bulk and layered systems. The suite's full-potential LMTO code uses a sophisticated basis and augmentation method that allows an efficient and precise solution to the band problem at different levels of theory, …

Go to article

Development Of B-Type And Multi-Ion Doped Carbonated Hydroxyapatite Bioceramics, Safarzadeh Marjan Apr 2020

Development Of B-Type And Multi-Ion Doped Carbonated Hydroxyapatite Bioceramics, Safarzadeh Marjan

Student Works (2020-2029)

The present research is aimed to investigate the effect of varying the carbonate to phosphate (CO32−/ PO43‒) molar ratios from 0.5 to 5 on the physical and mechanical properties of carbonated hydroxyapatite (CHA) synthesized by a wet chemical method. The sintering was performed under dry carbon dioxide atmosphere at 900 °C to maintain the B-type CHA structure. It was found that increases in CO32−/ PO43‒ ratio was accompanied by an increase in the c/a lattice ratio. The diffraction peaks of the synthesized 0.5-5 CHA powders exhibited a single phase material except for 5CHA which revealed the some minor calcite or …

Go to article

Effects Of Collision Damage On The Ultimate Strength Of Fpso Vessels, Muhammad Zubair Muis Alie, Dian Ramasari, Taufiqur Rachman, Ristiyanto Adiputra Apr 2020

Effects Of Collision Damage On The Ultimate Strength Of Fpso Vessels, Muhammad Zubair Muis Alie, Dian Ramasari, Taufiqur Rachman, Ristiyanto Adiputra

Makara Journal of Technology

Floating production storage offloading (FPSO) vessels are movable offshore structures. These structures are designed with large dimensions, and their decks are loaded with several types of equipment. During collision damage, the hull and deck parts loaded with equipment are severely affected. Therefore, the ultimate strength of FPSO vessels should be thoroughly checked and evaluated. The objective of the present study is to analyze the ultimate strength of FPSO vessels against collision damage characterized by hogging and sagging under longitudinal bending. The cross section of an FPSO vessel is modeled with elements composed of stiffened and unstiffened plates. The vessel length …

Go to article

Ionic Conductivity And Electrochemical Properties Of Alginate–Nn4no3-Based Biopolymer Electrolytes For Edlc Application, Norfatihah Binti Mazuki, Nur Muhitul Jalilah Rasali, Bouchta Sahraoui, Ahmad Salihin Samsudin Apr 2020

Ionic Conductivity And Electrochemical Properties Of Alginate–Nn4no3-Based Biopolymer Electrolytes For Edlc Application, Norfatihah Binti Mazuki, Nur Muhitul Jalilah Rasali, Bouchta Sahraoui, Ahmad Salihin Samsudin

Makara Journal of Technology

In this work, alginate doped with various contents of ammonium nitrate (NH4NO3) as a solid biopolymer electrolyte (SBE) was prepared via casting by using distilled water as a solvent. Impedance studies on alginate–NH4NO3 SBE films were conducted via impedance spectroscopy. The lowest bulk resistance (Rb) showed that the maximum ionic conductivity of the sample containing 25 wt.% NH4NO3 at ambient temperature (303 K) was 5.56 × 10−5 S cm−1. The temperature dependence of ionic conductivity was evaluated, and results confirmed that electrolytes followed an Arrhenius behavior. The highest conducting sample was fabricated into an electrical double-layer capacitor and characterized in …

Go to article

Synthesis Of Epoxy Monoethanolamide From Bauhinia Monandra Seed Oil, Adewale Adewuyi, Rotimi A. Oderinde Apr 2020

Synthesis Of Epoxy Monoethanolamide From Bauhinia Monandra Seed Oil, Adewale Adewuyi, Rotimi A. Oderinde

Makara Journal of Technology

In this study, we synthesized epoxidised monoethanolamide (EMA) from Bauhinia monandra seed oil (BMO) via a simple reaction route. In this process, BMO was transesterified to obtain a mixture of methyl esters, which was subjected to a urea adduct complexation reaction. The unsaturated methyl esters (BME) from the urea adduct complexation reaction were then epoxidised using performic acid produced in situ in a one-pot reaction system. The epoxidised methyl esters were converted to EMA by reacting them with monoethanolamine (1:10). The progression of the reaction was monitored using Fourier transform infrared spectroscopy and proton nuclear magnetic resonance spectroscopy, and the …

Go to article

Ethylene Carbonate And Polyethylene Glycol As Efficient Plasticizers In Cmc-Pva-Nh4no3-Based Polymer Electrolyte, Noor Saadiah Mohd Ali, Yuki Nagao, Ahmad Salihin Samsudin Apr 2020

Ethylene Carbonate And Polyethylene Glycol As Efficient Plasticizers In Cmc-Pva-Nh4no3-Based Polymer Electrolyte, Noor Saadiah Mohd Ali, Yuki Nagao, Ahmad Salihin Samsudin

Makara Journal of Technology

This study investigated the influence of plasticizers (polyethylene glycol [PEG] and ethylene carbonate [EC]) on the ionic conduction of CMC-PVA-NH4NO3. Blended biopolymer electrolytes (BBEs) based on carboxymethyl cellulose–polyvinyl alcohol (CMC-PVA) doped with ammonium nitrate (NH4NO3) were obtained via casting solution technique incorporated with PEG and EC, which acted as plasticizers. Electrical impedance spectroscopy (EIS) was conducted to evaluate the effect of plasticization on the ionic conduction properties. The ionic conductivity improved from 1.70 × 10−3 S/cm for un-plasticized BBEs to 3.92 × 10−3 S/cm for plasticized BBEs with EC and 3.00 × 10−3 S/cm for plasticized BBEs with PEG. The …

Go to article

Current Status Of Hydrothermal Treatment For Energy And Material Recovery Toward A Sustainable Post-Consumer Material Cycle, Baskoro Lokahita, Muhammad Aziz, Fumitake Takahashi Apr 2020

Current Status Of Hydrothermal Treatment For Energy And Material Recovery Toward A Sustainable Post-Consumer Material Cycle, Baskoro Lokahita, Muhammad Aziz, Fumitake Takahashi

Makara Journal of Technology

The demand for energy-efficient and environmentally friendly municipal solid waste (MSW) processing has increased in developing countries. The thermochemical process offers a fast and reliable solution to reutilize or reduce the volume of MSW. Hydrothermal treatment is a novel MSW treatment technology that is compatible with high-moisture-content feedstock. It involves the thermal degradation of MSW in pressurized water or steam, which promotes the disintegration of cellulosic and polymer materials. Recent advances have shown effective MSW conversion into homogenous solid hydrochar with higher energy density. Alkali and chlorine content, which causes issues in combustors, was successfully removed due to the washing …

Go to article

Liquefaction Potential Analysis Based On Nonlinear Ground Response On The Coastline Of Bengkulu City, Indonesia, Lindung Zalbuin Mase Apr 2020

Liquefaction Potential Analysis Based On Nonlinear Ground Response On The Coastline Of Bengkulu City, Indonesia, Lindung Zalbuin Mase

Makara Journal of Technology

This paper presents the study of the seismic response and liquefaction potential of the coastal area of Bengkulu City during the September 2007 Sumatra earthquake. The study is conducted by collecting site investigation data (standard penetration test) and applying input motion to observe soil response. Synthetic ground motion is generated by considering the important aspects of earthquakes, including focal depth, epicenter, earthquake source, and site classification. The synthetized ground motion is then used as the input motion in the seismic response analysis. The results of this analysis are spectral acceleration and peak ground acceleration at each depth. The resulting spectral …

Go to article

Comparison Of Phytoremediation And Filtration For Diamond-Mine-Tailings Water Treatment, M. Hafidhuddin Noor, Mijani Rahman, Akhmad Gazali, Nia Kania, Aulia Rahma, Erdina L.A. Rampun, Amalia E. Pratiwi, Muthia Elma Apr 2020

Comparison Of Phytoremediation And Filtration For Diamond-Mine-Tailings Water Treatment, M. Hafidhuddin Noor, Mijani Rahman, Akhmad Gazali, Nia Kania, Aulia Rahma, Erdina L.A. Rampun, Amalia E. Pratiwi, Muthia Elma

Makara Journal of Technology

The water pollution caused by diamond mine activities can kill aquatic life. In this work, we used phytoremediation and filtration to treat pond water polluted by the tailings of a diamond mine located in South Kalimantan, Indonesia. Einchhornia crassipes (water hyacinth) was utilized as the biomass for the phytoremediation process. Gravel (10–15 mm) and sand (0.1–1 mm) were used as filter media in the simple filtration setup, using an up-flow system (bottom to top). In the experiment, 16 L of diamond tailing water was poured into five phytoremediation reactors (each 60 L in volume), which were then tested over seven …

Go to article

Poly(Vinyl Alcohol)/Α-Chitin/Nanocellulose Composites Developed From Oil Palm Empty Fruit Bunch (Opefb) For Removal Of Cationic Dyes, Chun Fah Mok Apr 2020

Poly(Vinyl Alcohol)/Α-Chitin/Nanocellulose Composites Developed From Oil Palm Empty Fruit Bunch (Opefb) For Removal Of Cationic Dyes, Chun Fah Mok

Student Works (2020-2029)

In search of an eco-friendly polymeric adsorbent for dye effluent treatment application, poly(vinyl alcohol) (PVA)/chitin/nanocellulose composites were synthesized. The composites were reinforced by oil palm empty fruit bunch fibers (OPEFB)-derived nanocrystalline cellulose (NCC). With addition of 1 wt.% NCC, a maximum improvement of 57.64% and 50.66% in tensile strength and Young’s Modulus were achieved, respectively. However, the PVA-based composites exhibited low resistance in aqueous medium. Hence, maleic acid (MA) was incorporated, in view of modifying PVA-based composites through cross-linking reactions. The effect of varying chitin content (10 wt.%-30 wt.%) and MA content (10%-50% based on total solid content of composite) …

Go to article

Parametric Investigation Of Effect Of Abnormal Process Conditions On Self-Piercing Riveting, Taek-Eon Jeong, Dong-Hyuck Kam, Cheolhee Kim Apr 2020

Parametric Investigation Of Effect Of Abnormal Process Conditions On Self-Piercing Riveting, Taek-Eon Jeong, Dong-Hyuck Kam, Cheolhee Kim

Mechanical and Materials Engineering Faculty Publications and Presentations

Self-piercing riveting (SPR) is one of the mechanical joining processes, and its application to Al/Fe dissimilar materials combination, which is hard to weld, is expanding in the automotive industry. The main process parameters in SPR are types of rivet and die, setting force, and rivet setting speed. Previously, the relationship between the main process parameters and output parameters such as cross-sectional characteristics and joint strength has been studied to optimize the SPR process. In practical applications, there are unexpected and abnormal process conditions such as poor fit-up, angular misalignment, edge offset distance, and inaccurate setting and pre-clamping forces, and their …

Go to article

Through-Thickness Reinforcement And Repair Of Carbon Fiber Based Honeycomb Structures Under Flexure And Tension Of Adhesively Bonded Joints, Aleric Alden Sanders Apr 2020

Through-Thickness Reinforcement And Repair Of Carbon Fiber Based Honeycomb Structures Under Flexure And Tension Of Adhesively Bonded Joints, Aleric Alden Sanders

Mechanical & Aerospace Engineering Theses & Dissertations

Repair and reinforcement of composite honeycomb structures is an area of concern as higher demands are being placed on high strength, lightweight structural materials, such as carbon fiber reinforced plastics and corresponding honeycomb structures. A common issue with these structures is when a delamination in the facesheet may form and spread, leading to a failure scenario. An investigation of adding a through thickness reinforcement (TTR) to these structures at the sample level that undergo four-point-bending, tension, and joining methods is conducted throughout this thesis. The embedding of pultruded carbon fiber rods is found to be an ideal addition to composite …

Go to article

Experimental Determination Of The (0/−) Level For Mg Acceptors In Β-Ga2O3 Crystals, Christopher A. Lenyk, Timothy D. Gustafson, Sergey A. Basun, Larry E. Halliburton, Nancy C. Giles Apr 2020

Experimental Determination Of The (0/−) Level For Mg Acceptors In Β-Ga2O3 Crystals, Christopher A. Lenyk, Timothy D. Gustafson, Sergey A. Basun, Larry E. Halliburton, Nancy C. Giles

Faculty Publications

Electron paramagnetic resonance (EPR) is used to experimentally determine the (0/−) level of the Mg acceptor in an Mg-doped β-Ga2O3 crystal. Our results place this level 0.65 eV (±0.05 eV) above the valence band, a position closer to the valence band than the predictions of several recent computational studies. The crystal used in this investigation was grown by the Czochralski method and contains large concentrations of Mg acceptors and Ir donors, as well as a small concentration of Fe ions and an even smaller concentration of Cr ions. Below room temperature, illumination with 325 nm laser light …

Go to article

Compaction And Residual Stress Modeling In Composite Manufactured With Automated Fiber Placement, Von Clyde Jamora Apr 2020

Compaction And Residual Stress Modeling In Composite Manufactured With Automated Fiber Placement, Von Clyde Jamora

Mechanical & Aerospace Engineering Theses & Dissertations

Automated fiber placement is a state-of-the-art manufacturing process that allows for complex layup patterns and can quickly place, cut, and restart composite tows. However, with this type of manufacturing process layup defects are inevitable, and manufacturing defects propagate after curing. Process modeling is the considered approach for exploring the defect prediction. Two different but related works were conducted, which are the thermochemical and hyperelastic model and the residual deformation model. For the model before cooling, a hyperelastic model and a thermo-chemical were made to simulate the compaction and heat transfer. Temperature dependent properties that are a function of degree of …

Go to article

Enhanced Carrier Transport By Transition Metal Doping In Ws2 Field Effect Transistors, Maomao Liu, Sichen Wei, Simran Shahi, Hemendra Nath Jaiswal, Paolo Paletti, Sara Fathipour, Maja Remskar, Jun Jiao, Wansik Hwang, Fei Yao, Huamin Li Apr 2020

Enhanced Carrier Transport By Transition Metal Doping In Ws2 Field Effect Transistors, Maomao Liu, Sichen Wei, Simran Shahi, Hemendra Nath Jaiswal, Paolo Paletti, Sara Fathipour, Maja Remskar, Jun Jiao, Wansik Hwang, Fei Yao, Huamin Li

Physics Faculty Publications and Presentations

High contact resistance is one of the primary concerns for electronic device applications of two-dimensional (2D) layered semiconductors. Here, we explore the enhanced carrier transport through metal–semiconductor interfaces in WS2 field effect transistors (FETs) by introducing a typical transition metal, Cu, with two different doping strategies: (i) a “generalized” Cu doping by using randomly distributed Cu atoms along the channel and (ii) a “localized” Cu doping by adapting an ultrathin Cu layer at the metal–semiconductor interface. Compared to the pristine WS2 FETs, both the generalized Cu atomic dopant and localized Cu contact decoration can provide a Schottky-to-Ohmic contact …

Go to article

Energy Conservation With Open Source Ad Blockers, Joshua M. Pearce Mar 2020

Energy Conservation With Open Source Ad Blockers, Joshua M. Pearce

Michigan Tech Publications, Part 1

Internet-related electricity consumption is rising rapidly as global Internet users spend more than 6.5 h per day online. Open source ad blockers have the potential to reduce the time and thus electricity spent using computers by eliminating ads during Internet browsing and video streaming. In this study, three open source ad blockers are tested against a no-ad blocker control. Page load time is recorded for browsing a representative selection of the globally most-accessed websites, and the time spent watching ads on videos is quantified for both trending and non-trending content. The results show that page load time dropped 11% with …

Go to article

Influence Of Glass Fiber Reinforced Polymer Wraps On Corrosion Progression Of Bridge Piles In Marine Environments, Shayan Yazdani Mar 2020

Influence Of Glass Fiber Reinforced Polymer Wraps On Corrosion Progression Of Bridge Piles In Marine Environments, Shayan Yazdani

USF Tampa Graduate Theses and Dissertations

The Friendship Trail Bridge connecting Tampa to St. Petersburg was demolished in 2016. Thirteen 20 inches. by 20 inches. reinforced concrete piles supporting its superstructure were part of research studies conducted between 2004 and 2008 to explore the role of glass fiber reinforced polymers (GFRP) in corrosion repair. During demolition, piles were typically cut at the pile cap and in the splash zone. The resulting segments varied in length between 3 to 4 ft. These remnants were transported to the University of South Florida (USF) campus for postmortem analysis. The overarching goal was to establish the role of GFRP in …

Go to article

Alternate Materials For High-Speed Projectile Casing, Andrew W. Beard Mar 2020

Alternate Materials For High-Speed Projectile Casing, Andrew W. Beard

Theses and Dissertations

A high-speed projectile impact is a highly complex dynamic problem that can be simplified with the use of finite element analysis solvers. Abaqus/Explicit was used to evaluate the impact of various projectiles using a plane strain setup. Using a baseline stainless steel projectile, the proposed sandwich construction design was analyzed and compared to the baseline projectile. The overall goal was to see if a new composite casing could perform similarly to the simple baseline projectile. The sandwich construction used stainless steel, tungsten, and silicon-carbide reinforce aluminum as outer and inner shell materials. The core material was created using additive manufacturing …

Go to article

Wideband Metasurface Antenna, Thomas A. Lepley Mar 2020

Wideband Metasurface Antenna, Thomas A. Lepley

Theses and Dissertations

This effort explored design of metasurface antennas and evaluated their suitability for ultra-wideband applications (2 to 18 GHz). Six unit cell types were characterized. Eigenmode simulations produced frequency vs. phase data for the unit cells, from which impedance vs. gap size data was computed. A holographic design equation was used to generate the metasurface antenna designs. The unit cell simulations revealed that the assumption of single mode operation is a constraint for wideband designs. An 8" by 8" metasurface antenna with a Rogers 3010 dielectric and a design frequency of 10 GHz was fabricated and tested. It had a 1.5:1 …

Go to article

Investigation Of Ultem 9085 For Use In Printed Orbital Structures, William R. Gallagher Mar 2020

Investigation Of Ultem 9085 For Use In Printed Orbital Structures, William R. Gallagher

Theses and Dissertations

Additive manufacturing is revolutionizing industries ranging from medicine to space. However, the structural characteristics of plastic parts created by these methods are not as well understood as their more established counterparts. This research explored two relevant areas: how the structural characteristics of ULTEM 9085 plastic behaved after exposure to orbital conditions and the design of the cross-sectional area of a beam to be 3-D printed in microgravity based on the expected loads from the printer. To study orbital effects, ULTEM 9085 was printed into 1/4th scale ASTM D638- 14 dogbones using a Stratasys 450mc printer. These dogbones were placed in …

Go to article

Dynamic Micromechanical Fabry-Perot Cavity Sensors Fabricated By Multiphoton Absorption Onto Optical Fiber Tips, Jeremiah C. Williams Mar 2020

Dynamic Micromechanical Fabry-Perot Cavity Sensors Fabricated By Multiphoton Absorption Onto Optical Fiber Tips, Jeremiah C. Williams

Theses and Dissertations

This research leveraged two-photon polymerization microfabrication to integrate dynamic mechanical components with Fabry-Perot resonators onto the ends of low-loss optical fibers to prototype 3 micro-optic devices. The first device featured a multi-positional mirror that enabled thin-film deposition onto cavities of any length with mirrors of significant curvature, for refractive index sensing. The second device combined an FP cavity with a spring body featuring easily scalable stiffness for pressure sensing. The third device presented a high-speed rotating micro-anemometer for measuring a wide range of gas flows. All devices represent a significant reduction in size and weight over commercially available devices.

Go to article

Structural And Electronic Properties Of The Pure And Stable Elemental 3d Topological Dirac Semimetal Α-Sn, Maya N. Nair, Ivan Madarevic, Umamahesh Thupakula, Gertjan Lippertz, Niels Claessens, Pin-Cheng Lin, Harsh Bana, Sara Gonzalez, Giovanni Di Santo, Luca Petaccia, Lino M.C. Pereira, Chris Van Haesendonck, Margriet J. Van Bael Mar 2020

Structural And Electronic Properties Of The Pure And Stable Elemental 3d Topological Dirac Semimetal Α-Sn, Maya N. Nair, Ivan Madarevic, Umamahesh Thupakula, Gertjan Lippertz, Niels Claessens, Pin-Cheng Lin, Harsh Bana, Sara Gonzalez, Giovanni Di Santo, Luca Petaccia, Lino M.C. Pereira, Chris Van Haesendonck, Margriet J. Van Bael

Advanced Science Research Center

In-plane compressively strained α-Sn films have been theoretically predicted and experimentally proven to possess non-trivial electronic states of a 3D topological Dirac semimetal. The robustness of these states typically strongly depends on purity, homogeneity, and stability of the grown material itself. By developing a reliable fabrication process, we were able to grow pure strained α-Sn films on InSb(100), without heating the substrate during growth nor using any dopants. The α-Sn films were grown by molecular beam epitaxy, followed by experimental verification of the achieved chemical purity and structural properties of the film’s surface. Local insight into the surface morphology was …

Go to article

Cyclic Regeneration Of Nanostructured Composites For Catalytic Applications, Fatih Dogan Mar 2020

Cyclic Regeneration Of Nanostructured Composites For Catalytic Applications, Fatih Dogan

Materials Science and Engineering Faculty Research & Creative Works

A cermet catalyst material, defining a matrix having interconnected open pores, the matrix selected from the group consisting of YSZ and CGO and defining a substrate, a ceramic coating having a general formula AyBnOx at least partially coating the pores, and a plurality of metal particles A at least partially embedded in the ceramic coating. A is selected from the group consisting of Co, Cu, Ce, Ni, Ti, and combinations thereof and B is selected from the group consisting of Mo, W, Ce, and combinations thereof. When the coating is in a first oxidizing atmosphere …

Go to article

Characterization Of A Sagnac Loop Mirror-Based Hybrid Passive Variable Optical Coupler/Attenuator, Simeon Bikorimana, Muhammad A. Ummy, Abdullah Hossain, Richard Lin, Roger Dorsinville Mar 2020

Characterization Of A Sagnac Loop Mirror-Based Hybrid Passive Variable Optical Coupler/Attenuator, Simeon Bikorimana, Muhammad A. Ummy, Abdullah Hossain, Richard Lin, Roger Dorsinville

Publications and Research

The implementation and performance of a unidirectional all-single mode fiber hybrid passive variable optical coupler/attenuator based on a Sagnac loop mirror with a continuous variable coupling ratio using off-the-shelf optical sub-components are discussed. Parameters of two output ports of the unidirectional hybrid passive variable optical coupler/attenuator, such as maximum coupling ratio, insertion loss, excess loss, and wavelength-dependent return loss over the C-band at room temperature are reported. The reflectivity of the Sagnac loop mirror continuously varies from 0.1% to 99.9% by adjusting retarders of a polarization controller. The 3-dB coupling ratio (i.e., 50:50) between the two output ports of the …

Go to article

A Novel Self-Healing System: Towards A Sustainable Porous Asphalt, Shi Xu, Xueyan Liu, Amir Tabakovic, Erik Schlangen Mar 2020

A Novel Self-Healing System: Towards A Sustainable Porous Asphalt, Shi Xu, Xueyan Liu, Amir Tabakovic, Erik Schlangen

Articles

Self-healing asphalt, aimed to produce a sustainable asphalt pavement using green technology, has been studied in the past two decades. Technologies including encapsulated rejuvenator and induction heating have been proposed, demonstrated in the laboratory, and gradually evaluated in field application. This paper looks into the synergy effect of the above two technologies, where induction heating serves as the asphalt damage repair mechanism, requiring just 2 min heating time and encapsulated rejuvenator will replenish (rejuvenate) aged asphalt binder and reinstate bitumen’s healing ability. Moreover, the increased temperature from induction heating could in turn accelerate the diffusion process of rejuvenator into aged …

Go to article

Selection Of Blowing Agent For Metal Foam Production: A Review, Ankur Bisht, Brijesh Gangil, Vinay Kumar Patel Mar 2020

Selection Of Blowing Agent For Metal Foam Production: A Review, Ankur Bisht, Brijesh Gangil, Vinay Kumar Patel

Journal of Metals, Materials and Minerals

Metal foams are cellular solids in which gas is uniformly distributed throughout the metal matrix. One of the cheapest ways of evolving the gas is introducing the blowing agent in parent metal in liquid state. A blowing agent is defined as a material that decomposes under the presence of heat and releases gas which then propels the foaming process. The quality of final foam is influenced by several parameters such as composition, size and volume fraction of the blowing agent used. Different chemicals which can evolve gases such as carbonates and metal hydrides fit into the description of blowing agent. …

Go to article

An Approach To Search The Potentiality Of Node In Bamboo Strip Reinforced Composites, Mohammad Irfan Iqbal, Rashed Al Mizan, Ayub Nabi Khan Mar 2020

An Approach To Search The Potentiality Of Node In Bamboo Strip Reinforced Composites, Mohammad Irfan Iqbal, Rashed Al Mizan, Ayub Nabi Khan

Journal of Metals, Materials and Minerals

Bamboo has recently entered the composite sector with some attractive labels such as 'green'. The current commercial manufacturing method of bamboo composite removes the node's portion of bamboo culm during bamboo processing. This method generates a high amount of solid waste materials along with processing complexity and the scientific merit of this practice is also questionable. This research investigates the effects of culm nodes on bamboo based composite properties. In this study an approach to produce bamboo strips reinforced epoxy composites and their mechanical properties (e.g. tensile, flexural and impact properties) were reported. It was demonstrated that mechanical properties of …

Go to article

First Prev Next Last