Engineering Commons^™

Materials, Micro-Stacks And Related Applications Of Single-Chamber Solid Oxide Fuel Cells, Zhe Lv, Bo Wei, Zhi-Hong Wang, Yan-Ting Tian

Journal of Electrochemistry

Single-chamber solid oxide fuel cell (SC-SOFC) is a special type of fuel cells, in which both an anode and a cathode are placed in one chamber. Its working principle relies on the selective catalytic activity of the electrodes towards fuel and oxidant in a gas mixture, leading to the generation of an electromotive force. Because of its unique principle and structure, SC-SOFC has many advantages such as sealing-free, easy stacking, quick start-up and no carbon deposition, thus, it possesses large potential in application. Herein, the principles and characteristics of SC-SOFC are introduced. Furthermore, the SC-SOFC materials, micro-stack design, degeneration mechanisms …

Electrochemical Performance Improvement Of Li2Mno3 Cathode Materials By Mgf2 Coating, Du-Dan Wang, Fei Wang, Huan-Huan Zhai, Yu-Peng Li, Na-Chuan Yang, Kang-Hua Chen

Journal of Electrochemistry

Cathode material Li₂MnO₃ has received more and more attention owing to its high theoretical capacity (459 mAh·g ^-1). However, the low initial coulombic efficiency and the poor cycle stability hamper its practical application in lithium-ion batteries. Herein, we investigated the crystal structure and electrochemical performance of Li₂MnO₃ by introducing MgF₂ coating layer. The results indicated that the conversion of partial layer Li₂MnO₃ to spinel phase induced by MgF₂ coating could reduce the initial irreversible capacity and improve the first cycle efficiency. The initial coulombic efficiencies of the 0.5wt.%, …

Syntheses And Properties Of Ta5+ Doped Li7La3Zr2O12, Feng-Feng Peng, Shi-You Li, Tong-Tong Geng, Chun-Lei Li, Shuang-Wei Zeng

Journal of Electrochemistry

The tantalum ion (Ta ⁵⁺) doped garnet-type inorganic solid electrolyte Ta-LLZO was prepared by solid state reaction, and the effect of doping amount on the properties of the materials was investigated. The materials were characterized by X-ray diffraction (XRD), field emission electron scanning microscopy (FESEM) and electrochemical impedance spectroscopy (EIS). And the cycle stability was tested by assembly of LiFePO₄//LLZTO//Li all solid lithium battery. The results show that with the increase of Ta ⁵⁺ doping amount, the material appeared to form a single cubic phase structure. When the Ta ⁵⁺ doping content became 14.09wt.%, x=0.3, the …

Preparation And Characterization Of Cathode Supported Solid Oxide Fuel Cell, Xiao-Nan Bao, Guang-Jun Zhang, Shao-Rong Wang

Journal of Electrochemistry

A site deficient (La_0.8Sr_0.2)_0.95MnO₃ (LSM95) powder was synthesized by solid state reaction as a cathode material. The commercial Zr_0.9Sc_0.1SO_1.95 (SSZ) was selected as an electrolyte material and La_0.8Sr_0.2Cr_0.5Mn_0.5O₃- (LSCrM) was synthesized by sol-gel method as an anode material. Accordingly, single cells of LSCrM-CeO₂|SSZ|3YSZ-LSM95 were prepared by tape casting, sintering and impregnation. The single cell test results for LSCrM-CeO₂|SSZ|3YSZ-LSM95 with 0.11 g·cm ^-2 CeO₂ and using CH₄ as a fuel showed the power …

Direct Carbon Solid Oxide Fuel Cells, Jiang Liu, Xiao-Min Yan

Journal of Electrochemistry

Carbon is richly reserved in coal, biomasses, and many other nature resources. It is usually used as an energy source through oxygen oxidation reaction. The oxidation is generally realized through combustion which causes serious air pollution. Besides, the conversion efficiency of generating electricity through the combustion process is limited by Carnot efficiency. A direct carbon solid oxide fuel cell (DC-SOFC) is a solid oxide fuel cell (SOFC) directly operated with solid carbon as the fuel. It can convert the chemical energy of carbon into electricity with high efficiency. The concentration of produced CO₂ from a DC-SOFC is so high …

Research Progress Of Fuel Electrode In Oxide-Ion Conducting Solid Oxide Electrolysers, Ling-Ting Ye, Kui Xie

Journal of Electrochemistry

Solid oxide electrolysers are now attracting much more attentions because they can efficiently produce fuels by electrolyzing H₂O/CO₂. In this paper, a comprehensive introduction to the recent progress in the development of fuel electrode (cathode) materials is provided. The advantages, disadvantages and development trend towards various cathode materials are pointed out. The key scientific and technological problems in this field are emphasized.

Development Status And Prospects Of Hydrogen Production By High Temperature Solid Oxide Electrolysis, Wen-Qiang Zhang, Bo Yu

Journal of Electrochemistry

Solid oxide electrolysis cell is an advanced energy conversion device with high efficiency, simplicity, flexibility, and environmental friendliness. It is currently a research hotspot in the international energy field. This paper introduces and analyzes the basic principles, key materials, system components and developments of solid oxidation electrolysis cells. Furthermore, the recent research progresses, challenges and future development directions in solid oxidation electrolysis cells in the field of high-efficiency hydrogen production are summarized and outlined.

Nio@Rgo Supported Palladium And Silver Nanoparticles As Electrocatalysts For Oxygen Reduction Reaction, Shuo Yao, Tai-Zhong Huang, Rizwan Haider, Heng-Yi Fang, Jie-Mei Yu, Zhan-Kun Jiang, Dong Liang, Yue Sun, Xian-Xia Yuan

Journal of Electrochemistry

For pervasive applications of fuel cells, highly efficient and economical materials are required to replace Pt-based catalysts for oxygen reduction reaction (ORR). In this study, the NiO@rGO, Pd-NiO@rGO and Ag-NiO@rGO nanoparticles were synthesized, and their catalytic performances toward ORR were investigated. The results revealed that all the three materials were capable of catalyzing ORR, but both the Pd-NiO@rGO and Ag-NiO@rGO showed the better performances compared with the NiO@rGO in terms of the reaction pathway being 4-electron process, the increases of the onset potential and the intermediate yielding rate, as well as the extended stability. Moreover, the effect of Pd modification …

Perovskite Catalysts For Fuel Reforming In Sofc:A Review And Perspective, Tong Wei, Jian Li, Li-Chao Jia, Bo Chi, Jian Pu

Journal of Electrochemistry

Solid oxide fuel cell (SOFC) is a generating device by electrochemical reaction to transfer the chemical energy of fossil fuels (coal, oil and gas, etc.), the biomass fuel or other hydrocarbon fuels directly into electricity with higher energy conversion efficiency and lower pollution, which is recognized to be efficient green energy technology in the 21st century. However, when hydrocarbons are directly used as fuel, carbon deposition is easy to occur in nickel-based anode, thus, losing electrochemical catalytic activity. Fuel pre-reforming on the outside of the anode is an effective solution, which strongly relies on highly efficient and stable reforming catalysts. …

Research Progress In Ethane Dehydrogenation To Cogenerate Power And Value-Added Chemicals In Solid Oxide Fuel Cells, Yun Fan, Qi Wang, Jun Li, Jing-Li Luo, Xian-Zhu Fu

Journal of Electrochemistry

Increasing supplies of methane/shale gas have promoted global development of higher value chemicals such as ethylene production by ethane, which dramatically changes the markets of petrochemical industry. Clean and efficient transformation of ethane into higher value chemicals has far-reaching significance. Ethylene production through ethane steam cracking is a relatively matured technology for industrial production. However, the process consumes large amounts of energy and the presence of carbon deposition becomes a serious problem which is difficult to be solved. The cogenerated energy-chemicals solid oxide fuel cells have been widely studied because fuel gas can be converted into high-value chemicals via spontaneous …

Construction And Electrochemical Performance Of Garnet-Type Solid Electrolyte/Al-Li Alloy Interface, Jia-Lin Ma, Hong-Chun Wang, Zheng-Liang Gong, Yong Yang

Journal of Electrochemistry

Garnet-type solid electrolyte is a newly developed Li ion conductor and promising in the application of all-solid-state batteries. However, Garnet is incompatible with Li anode, which restricts the application of Garnet-type solid batteries. In order to improve the contact between Garnet-type solid electrolyte and Li electrode, a composite anode which contains Al-Li alloy (Al₄Li₉) was prepared as an electrode. Al-Li alloy has many advantages such as easy preparation, low cost, simple post-treatment and high capacity. Garnet-type Li_6.5La₃Zr_1.75W_0.25O₁₂ (LLZWO) was synthesized via solid-state reaction. Garnet solid electrolyte has …

Recent Advances Of Co2 Electrochemical Reduction In Solid Oxide Electrolysis Cells, Yi-Hang Li, Chang-Rong Xia

Journal of Electrochemistry

Solid oxide electrolysis cells (SOECs) have stimulated wide interests for their promising application in the reduction of CO₂ emissions and the storage of renewable energy. Here, the advances made in the development of cathode materials including cermets and perovskite oxides in our research group, are summarized, along with the design of cell configurations. The electrochemical kinetics and performances of cathodes and cells are discussed and analyzed. It is expected that this brief review offers critical insights and useful guidelines for developing superior electrodes and SOECs in the future.

Evaluation And Update Of Mash Test Vehicles, Kellon B. Ronspies

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The Manual for Assessing Safety Hardware (MASH) requires full-scale crash testing of roadside features using worst practical impact conditions. Vehicle selection for full-scale crash testing is intended to be representative of the contemporary passenger vehicle fleet. Researchers at the Midwest Roadside Safety Facility (MwRSF) investigated attributes of passenger vehicle sales to determine if the vehicle selection criteria shown in MASH should be revised to accommodate changes in the vehicle fleet. A methodology was considered to affordably re-analyze the vehicle fleet when necessary to ensure MASH vehicle selection criteria are reflective of vehicles currently on roadways.

Representative vehicles were documented using …

Designing An Adjustable And Transportable Staircase, Allison Currey

Undergraduate Honors Thesis Projects

People climb stairs every day, whether it is at work, a store, or at home; however, there are populations such as people who are elderly, with pathologies, with Parkinson’s disease, or have suffered from a stroke that see climbing the stairs as a challenging task and it decreases their mobility and quality of life. Factors such as muscle weakness, strategy, and balance have been previously investigated in these populations during stair climbing. However, few studies have researched how stair climb ability, balance, and perception of difficulty are influenced by step height. The objective of this thesis is to design a …

Faculty Instruction Face Shield Project, David Holden, John Schneiderhan

Michigan Tech 3D Designs

Early in the spring of 2020 project contributors David Holden and John Schneiderhan began test printing a variety of open source Personal Protective Equipment (PPE)/Covid related items that could help protect or prevent the spread of the emerging virus. With assistance from Pete Baril of the Western Upper Peninsula Health Department (WUPHD) approval was obtained for the face shields to be used in the health care and nursing homes in the area. With the support and approval from university and library administration efforts were coordinated with Dr. Joshua Pearce and the students from the MOST lab to concentrate on the …

On-Chip Terahertz Modulation And Emission With Integrated Graphene Junctions, Joshua O. Island, Peter Kissin, Jacob Schalch, Xiaomeng Cui, Sheikh Rubaiat Ui Haque, Alex Potts, Takashi Taniguchi, Kanji Watanabe, Richard D. Averitt, Andrea F. Young

Physics & Astronomy Faculty Research

The efficient modulation and control of ultrafast signals on-chip is of central importance in terahertz (THz) communications and a promis- ing route toward sub-diffraction limit THz spectroscopy. Two-dimensional (2D) materials may provide a platform for these endeavors. We explore this potential, integrating high-quality graphene p–n junctions within two types of planar transmission line circuits to modulate and emit picosecond pulses. In a coplanar strip line geometry, we demonstrate the electrical modulation of THz signal transmission by 95%. In a Goubau waveguide geometry, we achieve complete gate-tunable control over THz emission from a photoexcited graphene junction. These studies inform the development …

Thermal Modeling Of Additive Manufacturing Using Graph Theory: Validation With Directed Energy Deposition, Jordan Severson

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Metal additive manufacturing (AM/3D printing) offers unparalleled advantages over conventional manufacturing, including greater design freedom and a lower lead time. However, the use of AM parts in safety-critical industries, such as aerospace and biomedical, is limited by the tendency of the process to create flaws that can lead to sudden failure during use. The root cause of flaw formation in metal AM parts, such as porosity and deformation, is linked to the temperature inside the part during the process, called the thermal history. The thermal history is a function of the process parameters and part design.

Consequently, the first step …

Laser Micropatterning Effects On Corrosion Resistance Of Pure Magnesium Surfaces, Yahya Efe Yayoglu

USF Tampa Graduate Theses and Dissertations

Magnesium and its alloys are good candidates to manufacture medical implants. They have excellent biocompatibility and because they biodegrade secondary surgical operation to remove the implant could be eliminated. However, in aqueous environments, magnesium alloys rapidly corrode, resulting in premature degradation of the implant along with biologically intolerable hydrogen gas generation. In literature, there are multiple studies focused on creating water repelling hydrophobic magnesium surfaces in order to decrease corrosion rates. Hydrophobic properties can be achieved by creation of a roughness profile on an initially smooth surface combined with a treatment that reduces the free surface energy. In theory, hydrophobic …

Mid-Ir Optical Refrigeration And Radiation Balanced Lasers, Saeid Rostami

Optical Science and Engineering ETDs

This dissertation reports recent advances in mid-infrared (mid-IR) optical refrigeration and Radiation Balanced Lasers (RBLs). The first demonstration of optical refrigeration in Ho:YLF and Tm:YLF crystals as promising mid-IR laser cooling candidates is reported. Room temperature laser cooling efficiency of Tm- and Ho-doped crystals at different excitation polarization is measured and their external quantum efficiency and background absorption are extracted. Complete characterization of laser cooling samples is obtained via performing detailed low-temperature spectroscopic analysis, and their minimum achievable temperature as well as conditions to achieve laser cooling efficiency enhancement in mid-IR are investigated. By developing a Thulium-doped fiber amplifier, seeded …

Quantifying Wicking In Functionlized Surfaces, Maureen Winter, Ryan Regan, Alfred Tsubaki, Craig Zuhlke, Dennis Alexander, George Gogos

UCARE: Research Products

Wicking remains the enigmatic key factor in many research areas. From boiling in power plants, to anti-icing on plane wings, to medical instruments, to heat pipes, efficiency and safety depend on how quickly a surface becomes wet. Yet wicking remains difficult to quantify and define as a property of the surface. This experiment strives to measure the wicking property by examining the rate that a liquid can be pulled out of a container. A superhydrophilic surface is placed in contact with the liquid at the bottom of a tube so that the volume flow rate across the surface can be …

Growth And Characterization Of 2d Layered Materials, Algene Fryer Ii

USF Tampa Graduate Theses and Dissertations

2D layered materials are becoming an important area of research due to their exceptional electrical and optical properties. Specifically, 2D layered monochalcogenides are known for their high carrier motilities, whereas layered metal halides have been shown to have noteworthy photoresponsivity. Despite the assortment of 2D layered materials, the search for reliable and scalable synthesis methods is still a challenge in this family of materials. Often a certain growth technique will compromise a desirable trait needed for further fabrication, such as the quality of the crystal or its coverage on a substrate. In this study, two growth techniques that incorporate changeable …

Mitigating Safety Concerns And Profit/Production Losses For Chemical Process Control Systems Under Cyberattacks Via Design/Control Methods, Helen Durand, Matthew Wegener

Chemical Engineering and Materials Science Faculty Research Publications

One of the challenges for chemical processes today, from a safety and profit standpoint, is the potential that cyberattacks could be performed on components of process control systems. Safety issues could be catastrophic; however, because the nonlinear systems definition of a cyberattack has similarities to a nonlinear systems definition of faults, many processes have already been instrumented to handle various problematic input conditions. Also challenging is the question of how to design a system that is resilient to attacks attempting to impact the production volumes or profits of a company. In this work, we explore a process/equipment design framework for …

Loading Orientation Dependence On The Compressive Response Of Ice-Templated Ceramic-Polymer Composites, Sashanka Akurati, Justine Marin, Dipankar Ghosh

College of Engineering & Technology (Batten) Posters

Natural materials are made from weak constituents, yet exhibit an excellent synergy of high stiffness, strength, and damage-tolerance. They consist of alternate layers of the hard and soft phases with a complex hierarchical structural organization. The ice-templating technique provides an approach to fabricate multilayered architectures for engineering applications. In this technique, an aqueous ceramic suspension is solidified unidirectionally leading to phase separation into alternating layers of ice-crystals and ceramic particles. Ice-crystals are sublimated by freeze-drying process and resultant ceramic foams are sintered to impart strength. The fabricated sintered ceramic foams contain alternate layers of oriented ceramic lamella walls and pores. …

Morphology And Structure Of Pb Thin Films Grown On Si (111) By Pulsed Laser Deposition, Bektur Abdisatarov

Masters Theses & Specialist Projects

Pulsed laser deposition (PLD) is a versatile thin film deposition technique in which high powered laser beam interacts with a target material inside an ultrahigh vacuum chamber. Highly energetic particles such as electrons, atoms, protons, and ions generate a plasma plume that directed towards a substrate material where recondenses form a thin film. PLD is an effective and reliable method to create varieties of thin films such as metal, polymer, and ceramic for many technologically essential applications.

In this study, thin Pb films were grown by pulsed laser deposition on Si (111) at various laser fluences, pulse wavelengths, deposition times, …

Synthesis Of Sic Resin For 3d Printing Of Sic Ceramics By Digital Light Processing, Kevin Zhao, Bai Cui

UCARE: Research Products

Silicon carbide (SiC) resin is produced through shear mixing 0.1-1 μm SiC powders with Tethon’s high load Genesis resin base. Resins of varying SiC vol.% were synthesized to test the loading limit of the resin base; 10, 20, and 30 vol.% of SiC were made with the resin base handling the higher loads quite well. Several attempts were made at printing using the Tethon Bison 1000 DLP printer with higher loads of SiC showing better results even with lower intensity UV lights andtimes.

Defect Characterization Of Additively Manufactured Parts, Sabrina D'Alesandro, Joy Gockel, Andrew Harvey

Celebration of Undergraduate & Graduate Research, Scholarship, and Creative Activities Materials

This document describes various image processing techniques to be used for defect characterization of additively manufactured parts. This will help the reader gain knowledge of materials science engineering and the nuances in analyzing data from image processing software.

Additive manufacturing is shaping the manufacturing world through simplistic household printers’ to more complex metal printers used for a variety of applications. Specifically, laser powder bed fusion (LPBF) is an additive manufacturing process that deposits metal powder over the build plate and melts it with a laser in the shape of the build part. In order to make LPBF more efficient with …

A Novel Method For Making Titanium Dioxide For Photocatalytic Applications, Gary Wilson

Graduate Theses & Non-Theses

Titanium dioxide possesses near-ideal properties for large-scale application as a photocatalyst. It is cheap and abundant, nontoxic, and environmentally safe. However, it still suffers from logistical problems preventing its application in industry: namely, rapid electron-hole recombination and inability to utilize visible light. For nearly five decades researchers in this booming field have made numerous attempts to address these problems, doping and combining titanium dioxide with a wide range of materials. A novel ambient-temperature approach to synthesis and doping/modification of anatase-form titanium dioxide was attempted using both oxygen-rich and oxygen deprived synthetic routes. Reactants were exposed to various wavelengths of ultraviolet …

Correction To: Recommendations Of Rilem Tc 260-Rsc For Using Superabsorbent Polymers (Sap) For Improving Freeze–Thaw Resistance Of Cement-Based Materials (Materials And Structures, (2019), 52, 4, (75), 10.1617/S11527-019-1375-4), Viktor Mechtcherine, Christof Schröfl, Michaela Reichardt, Agnieszka J. Klemm, Kamal Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Agnieszka J. Klemm is affiliated to Glasgow Caledonian University, Glasgow, UK.

Estimation Of Lubrication Layer Thickness And Composition Through Reverse Engineering Of Interface Rheometry Tests, Alexis Salinas, Dimitri Feys

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

During concrete pumping, a lubrication layer is formed near the pipe wall. Extensive research has been performed on measuring and modeling the properties of this layer and using these values to predict pumping pressures. However, there are numerous discussions in the literature about the composition and thickness of this layer: can it be considered mortar, a micromortar, or is it cement paste? In this paper, possible solutions for the thickness and composition of the lubrication layer are derived from interface rheometry tests. It is assumed that the lubrication layer is composed of one or more concentric layers of paste or …

Investigation Of Selective Laser Melting Fabricated Internal Cooling Channels, Colin Jack

Masters Theses

Channels where coolant is run to cool a system are common in injection mold tooling. Conventionally, these channels are machined into the mold. This has limited the design of mold cooling systems to the constraints of traditional machining processes, where straight circular channels machined from cast material are typical. The transfer of heat away from the part cavity into these cooling channels has a large effect on the cooling time of the injection mold cycle. In this investigation, laser powder bed fusion processes were used to create non-circular cooling channels. To compare cooling performance, elliptical and circular channels of equal …