Engineering Commons^™

Mechanical Properties Of Boehmeria Nivea Natural Fabric Reinforced Epoxy Matrix Composite Prepared By Vacuum-Assisted Resin Infusion Molding, Fabio Da Costa Garcia Filho, Fernanda Santos Da Luz, Lucio Fabio Cassiano Nascimento, Kestur Gundappa Satyanarayana, Jaroslaw W. Drelich, Sergio Neves Monteiro

Michigan Tech Publications, Part 1

Natural lignocellulosic fibers and corresponding fabrics have been gaining notoriety in recent decades as reinforcement options for polymer matrices associated with industrially applied composites. These natural fibers and fabrics exhibit competitive properties when compared with some synthetics such as glass fiber. In particular, the use of fabrics made from natural fibers might be considered a more ecient alternative, since they provide multidirectional reinforcement and allow the introduction of a larger volume fraction of fibers in the composite. In this context, it is important to understand the mechanical performance of natural fabric composites as a basic condition to ensure ecient engineering …

Development Of Reduced Chemical Kinetic Models For The Numerical Simulation Of Combustion And Emissions Behavior Of Representative Conventional And Bio-Derived Fuels, Mazen A. Eldeeb

Mineta Transportation Institute

The study addresses two of the main challenges facing combustion modeling for transportation fuels: simultaneous simulation of non-related combustion problems and reducing the computational cost of the modeling process itself. To address the first challenge, researchers determine a characteristic flame time from thermal diffusivity and laminar burning velocity. Researchers examine parametric dependence of flame time and ignition delay time on pressure, temperature and equivalence ratio for methane, based on validated chemical kinetic mechanisms. The study reveals flame time and ignition delay time show similar temperature dependence, flame time has stronger dependence on equivalence ratio and weaker dependence on pressure than …

Effects Of New And Recycle Flux On The Mechanical Properties Of Submerged Arc Welded (Saw) Line Pipe Grade X52m And X65m, Taib Meor Mohd Adli

Student Works (2020-2029)

Two line pipe grade X52M and X65M were manufactured using submerged arc welding process. For each grade, two different welding flux condition were simulated, i.e. 100% new flux and 100% recycle flux. The flux used was aluminate basic type trade name OP 132. The outside diameter and wall thickness for X52M was 610mm x 12.7mm and for X65M was 762mm x 14.3mm. Lower weld re-entrant angle and higher weld bead height were observed in recycle flux condition. Lower weld manganese content recorded in recycle flux condition. And lower mechanical tests (i.e. tensile, impact, and hardness) value reported for recycle flux …

Prediction Of Flotation Efficiency Of Metal Sulfides Using An Original Hybrid Machine Learning Model, Rachel Cook, Keitumetse Cathrine Monyake, Muhammad Badar Hayat, Aditya Kumar, Lana Alagha

Materials Science and Engineering Faculty Research & Creative Works

Froth flotation process is extensively used for selective separation of base metal sulfides from uneconomic mineral resources. Reliable prediction of process outcomes (metal recovery and grade) is vital to ensure peak performance. This work employs an innovative hybrid machine learning (ML) model—constructed by combining the random forest model and the firefly algorithm—to predict froth flotation efficiency of galena and chalcopyrite in relation to various experimental process parameters. The hybrid model's prediction performance was rigorously evaluated and compared against four different standalone ML models. The outcomes of this study illustrate that the hybrid ML model has the prediction ability to process …

Thermal Properties Of Sodium Borosilicate Glasses As A Function Of Sulfur Content, Jason M. Lonergan, Charmayne Lonergan, Joshua Silverstein, Pornsinee Cholsaipant, John Mccloy

Materials Science and Engineering Faculty Research & Creative Works

Sulfur trioxide (SO₃) additions, up to 3.0 mass%, were systematically investigated for effects on the physical properties of sodium borosilicate glass melted in air, with a sulfur-free composition of 50SiO₂–10Al₂O₃–12B₂O₃–21Na₂O–7CaO (mass%). Solubility measurements, using electron microscopy chemical analysis, determined the maximum loading to be ~1.2 mass% SO₃. It was found that measured sulfur (here as sulfate) additions up to 1.18 mass% increased the glass transition temperature by 3%, thermal diffusivity by 11%, heat capacity by 10%, and thermal conductivity by 20%, and decreased the …

Distributed Manufacturing Of Open Source Medical Hardware For Pandemics, Joshua M. Pearce

Michigan Tech Publications, Part 1

Distributed digital manufacturing offers a solution to medical supply and technology shortages during pandemics. To prepare for the next pandemic, this study reviews the state-of-the-art of open hardware designs needed in a COVID-19-like pandemic. It evaluates the readiness of the top twenty technologies requested by the Government of India. The results show that the majority of the actual medical products have some open source development, however, only 15% of the supporting technologies required to produce them are freely available. The results show there is still considerable research needed to provide open source paths for the development of all the medical …

Numerical And Analytical Methods To Predict Behavior Of Reinforced Ductile Concrete Composites, Mandeep Pokhrel

Dissertations

Structural components constructed with ductile concrete composites, such as high-performance fiber-reinforced cementitious composites (HPFRCC), are known to perform exceptionally well under extreme mechanical and environmental loading conditions compared to traditional concrete. HPFRCC flexural components exhibit enhanced performance in terms of displacement ductility, energy dissipation capacity, and damage tolerance capacity. However, recent research suggests that the flexural behavior of reinforced HPFRCCs in terms of crack progression, reinforcement plasticity, and failure mechanism is significantly different than conventional reinforced concrete. Specifically, the failure mode of flexural members is found to be predominantly through the fracture of longitudinal reinforcement rather than compression crushing of …

The Impact Of Conversion On The Durability Of Calcium Aluminate Cement Concrete Systems, Marwa Mohsen Korayem

Dissertations

The deterioration of infrastructure in North America has resulted in a significant need for concrete repair materials that can be used to maintain service life of these structures. Hydraulic cement based rapid repair materials can be used to repair pavement and bridge deterioration with minimal impact on economic activities such as freight handling or public transportation. While there are many options for use in repair situations, calcium aluminate cements have become more popular recently, particularly in situations where repairs must be completed rapidly.

Calcium aluminate cement (CAC) is a cement characterized by its rapid strength gain, even at low temperatures …

Modeling Single Microtubules As A Colloidal System To Measure The Harmonic Interactions Between Tubulin Dimers In Bovine Brain Derived Versus Cancer Cell Derived Microtubules, Arooj Aslam

Dissertations

The local properties of tubulin dimers dictate the properties of the larger microtubule assembly. In order to elucidate this connection, tubulin-tubulin interactions are be modeled as harmonic interactions to map the stiffness matrix along the length of the microtubule. The strength of the interactions are measured by imaging and tracking the movement of segments along the microtubule over time, and then performing a fourier transform to extract the natural vibrational frequencies. Using this method the first ever reported experimental phonon spectrum of the microtubule is reported. This method can also be applied to other biological materials, and opens new doors …

Schwann Cells In Combination With Gag-Mimetic Scaffolds For Spinal Cord Repair, Sharareh Hashemi

Dissertations

Spinal cord injury (SCI) being a devastating neurological dysfunction can cause extensive irreversible neuronal loss and axonal damage. Fifty-four cases of spinal cord injury per million people occur annually in the United States. Due to the loss of glial cells and demyelination of axons, the neuronal function of surviving neurons is disrupted leading to permanent loss of sensory and motor functions. The glial scar formed by astrogliosis at the chronic stage protects undamaged tissues, but it is known to be a major barrier for axonal regeneration. The limited regeneration capacity of spinal cord makes it challenging to successfully treat the …

Open Source High-Temperature Reprap For 3-D Printing Heat-Sterilizable Ppe And Other Applications, Noah G. Skrzypczak, Nagendra Gautam Tanikella, Joshua M. Pearce

Michigan Tech Publications, Part 1

Thermal sterilization is generally avoided for 3-D printed components because of the relatively low deformation temperatures for common thermoplastics used for material extrusion-based additive manufacturing. 3-D printing materials required for high-temperature heat sterilizable components for COVID-19 and other applications demands 3-D printers with heated beds, hot ends that can reach higher temperatures than polytetrafluoroethylene (PTFE) hot ends and heated chambers to avoid part warping and delamination. There are several high temperature printers on the market, but their high costs make them inaccessible for full home-based distributed manufacturing required during pandemic lockdowns. To allow for all these requirements to be met …

Fly Ash Based Geopolymer For High Temperature And High Compressive Strength Applications In Aggressive Environment, Aaryan Manoj Nair, Akm S. Rahman

Publications and Research

Geopolymers are the results of geosynthetic reactions between aluminosilicates and strong bases. This results in chemical bonds between aluminum (Al), Silicon (Si)and oxygen (O) composing polymer rings in tetrahedral coordination. These bonds give them widespread useful applications such as high heat bearing ceramics, and base construction material whilst being far more environmentally conscious. The purpose of the experiment is to examine the effect of Silicon Carbide whisker and inorganic glass particles on thermal and mechanical properties of Geopolymers. This study will help understand the effect of various compositions and concentrations of SiO₂ in mechanical strength. In this experiment, the …

Aps March Meeting 2020: Undergraduate-Friendly Research In Soft Matter And Beyond, Vianney Gimenez-Pinto

Title III Professional Development Reports

The in-person APS March Meeting 2020 taking place in Denver during March 02-06, 2020 was canceled in the last minute out of Covid-19 concerns for the well-being of the scientific community as well as the population of the city of Denver and the state of Colorado. Nevertheless, well-planned logistics by the physics community and the APS leadership, allowed attendants to share their findings, presenting their research works to their peers, and continuing the work towards the advancement of science. Given the historical and on-going under-representation of students of color in science and technology at all academic levels, there is a …

Experimental Performance Evaluation Of A Hyper-Branched Polymer Electrolyte For Rechargeable Li-Air Batteries, Susanta K. Das, Joel Berry, Abhijit Sarkar

Mechanical Engineering Publications

A hyper-branched polymer (HBP) electrolyte is synthesized for rechargeable lithium-air (Li-air) battery cell and experimentally evaluated its performance in actual battery cell environment. Several real-world battery cells were fabricated with synthesized HBP electrolyte, pure lithium metal as anode and an oxygen permeable air cathode to evaluate reproducibility of the rechargeable Li-air battery cell. The effect of various conditions such as various HBP based electrolytes, discharge current −0.1~0.5 mA, cathode preparation processes and carbon contents on the battery cell performance were experimentally evaluated using the fabricated battery cells under dry air condition. Detailed HBP electrolyte synthesis procedures and experimental performance evaluation …

Parametric Nasopharyngeal Swab For Sampling Covid-19 And Other Respiratory Viruses: Open Source Design, Sla 3-D Printing And Uv Curing System, Nicole Gallup, Adam Pringle, Shane Oberloier, Nagendra Gautam Tanikella, Joshua M. Pearce

Michigan Tech Publications, Part 1

Access to nasopharyngeal swabs for sampling remain a bottleneck in some regions for COVID19 testing. This study develops a distributed manufacturing solution using only an open source manufacturing tool chain consisting of two types of open source 3-D printing and batch UV curing, and provides a parametric fully free design of a nasopharyngeal swab. The swab was designed using parametric OpenSCAD in two components (a head with engineered break point and various handles), which has several advantages: i) minimizing print time on relatively slow SLA printers, ii) enabling the use of smaller print volume open source SLA printers, iii) reducing …

Effect Of Post-Consumer Content And Bioplastic Incorporation On Polymeric Resin In Consumer Applications, Shelby Bicknell

Electronic Theses & Dissertations

Controversy surrounds the use of plastic products, primarily due to their potentially negative impact on the environment at the end of their lifecycle. The most widely used plastics are manufactured from petrochemicals such as petroleum, coal or natural gas. Petrochemical plastics are not able to readily breakdown in the environment, which aggravates the existing pollution problems. Fortunately, there are eco-friendly alternatives to petrochemical-based plastics. Bioplastics may be derived from renewable sources, biodegradable, or both. Bio-based plastics are plastics that may be derived from renewable biomass sources including, but not limited to, vegetable oils, cornstarch, straw, woodchips, and food waste. They …

Structure, Thermophysical Properties Of Liquids, And Their Connection With Glass Formability, Rongrong Dai

McKelvey School of Engineering Graduate Student Theses & Dissertations

Metallic glasses have drawn significant attention due to their unique properties, such as high strength, excellent elastic energy storage capacity, and versatile processability. However, why some liquids can easily form metallic glasses while others donմ is still unclear. Since metallic glasses are formed when liquids are cooled fast enough to bypass crystallization, we hope to better understand glass formation by investigating the structural evolution and thermophysical properties of the liquids as they are cooled toward the glass transition. Multiple molecular dynamics simulations suggest a crossover temperature for the dynamics near the liquidus temperature, which corresponds to the onset of cooperative …

First-Principles Studies Of Anion Engineering In Functional Ceramics, Steven Timothy Hartman

McKelvey School of Engineering Graduate Student Theses & Dissertations

Ceramic materials display a wide variety of valuable properties, such as ferroelectricity, superconductivity, and magnetic ordering, due to the partially covalent bonds which connect the cations and anions. While many breakthroughs have been made by mixing multiple cations on a sublattice, the equivalent mixed-anion ceramics have not received nearly as much attention, despite the key role the anion plays in the materials’ properties. There is great potential for functional ceramics design using anion engineering, which aims to tune the materials properties by adding and removing different types of anions in existing classes of ceramic materials. In this dissertation, I present …

Scalable Synthesis Of Nanostructured Metal Oxide Films Using Aerosol Chemical Vapor Deposition For Energy Storage Applications, Clayton Kacica

McKelvey School of Engineering Graduate Student Theses & Dissertations

As global energy consumption continues to rapidly increase, the need for new technologies to meet this demand in a sustainable way. Renewable sources such as solar and wind power are being increasingly utilized for electricity generation. However, the intermittent nature of these sources requires large-scale energy storage to reliably provide consistent power. Current grid-scale energy storage usually involves pumped hydroelectric systems, which are limited by location, or flywheel systems, which have limited use in high-power low-energy applications. Electrochemical storage solutions, such as lithium-ion batteries, provide robust energy storage that is not limited by location with a range of power and …

Effects Of Hard-To-Soft Segment Ratios On The Synthesis And Physico-Mechanical Properties Of Polyurethane Films, Aaron C. Wilson

Mechanical Engineering Theses

Blood-contacting cardiovascular stents often induce a secondary clotting event due to unrestricted enzymatic activities. The use of hemocompatible polyurethane coatings on these implantable devices is one of the most promising methods to reduce device rejection. In this study, four commercial polyurethane films of various thicknesses and compositions were evaluated for their anticoagulation properties. Results suggested that these films exhibited excellent thermal and physico-mechanical properties while capable of increasing contact time with blood plasma by over a thousand-fold as compared to a control surface. Due to the unknown structure and composition of these commercial films, polyurethane samples were synthesized from toluene …

Applied-Force Oscillations In Avalanche Dynamics, Louis W. Mcfaul, Gregory Sparks, Jordan Sickle, Jonathan T. Uhl, Wendelin J. Wright, Robert Maass, Karin A. Dahmen

Faculty Journal Articles

Until now most studies of discrete plasticity have focused on systems that are assumed to be driven by a monotonically increasing force; in many real systems, however, the driving force includes damped oscillations or oscillations induced by the propagation of discrete events or “slip avalanches.” In both cases, these oscillations may obscure the true dynamics. Here we effectively consider both cases by investigating the effects of damped oscillations in the external driving force on avalanche dynamics. We compare model simulations of slip avalanches under mean-field dynamics with observations in slip-avalanche experiments on slowly compressed micrometer-sized Au specimens using open-loop force …

Fabrication Of Nanoscale Columnar Diodes By Glancing Angle Deposition, Jacob D. Weightman

Macalester Journal of Physics and Astronomy

Glancing angle deposition (GLAD) is a process in which thin films are deposited onto a substrate with obliquely incident vapor together with precisely controlled azimuthal substrate rotation. Ballistic shadowing effects due to the oblique incidence produce nanoscale structures, and a variety of feature shapes, including tilted columns, helices, and vertical columns can be achieved by varying the azimuthal rotation during the deposition process. Due to this control of morphology and the compatibility of the process with a wide variety of materials, GLAD films have found applications in a variety of fields including sensing, photonics, photovoltaics, and catalysis, where they are …

Electrospun Silk-Boron Nitride Nanofibers With Tunable Structure And Properties., Ye Xue, Xiao Hu

College of Science & Mathematics Departmental Research

In this study, hexagonal boron nitride (h-BN) nanosheets and Bombyx mori silk fibroin (SF) proteins were combined and electrospun into BNSF nanofibers with different ratios. It was found that the surface morphology and crosslinking density of the nanofibers can be tuned through the mixing ratios. Fourier transform infrared spectroscopy study showed that pure SF electrospun fibers were dominated by random coils and they gradually became α-helical structures with increasing h-BN nanosheet content, which indicates that the structure of the nanofiber material is tunable. Thermal stability of electrospun BNSF nanofibers were largely improved by the good thermal stability of BN, and …

Comparative Analysis And Dynamic Response Of Garolites Under Temperature Spectrum Using Low Velocity Impact Test, Birendra Chaudhary

Honors Theses

The purpose of this study was to examine the dynamic response of three different grades of garolites under the temperature spectrum. High-Temperature G-11 Sheet (HTG), Impact Resistance Garolite E-glass (HIG), and Economical Garolite (EG) were tested using an Instron Dynatup 8250 impact tester. Three specimens were used for all three composites and were tested at 6 different temperatures, -10^oC, 25^oC, 50^oC, 100^oC, 150^oC and 200^oC using the Low-Velocity Impact Machine with 20 Kip punch shear load cell. The results showed that HIG had the highest resistance to punch …

Product Realization Capstone: Element Proof Safety Steps For Willie Price Lab School, Catherine Thomas, Allan Heuerman, Jared Mumme

Honors Theses

The purpose of this document is to describe the process we took to complete our capstone which paired the Center for Manufacturing Excellence with the Willie Price Lab School. The goal of the capstone was to remake step stools for the students of Willie Price, as the last stools failed to withstand weather damage. However, with the COVID-19 pandemic, plans were hindered, shifting the goal from actually producing the steps to creating instructions so that a younger Center for Manufacturing class could complete the production at a later date. Standardized Work Instructions, a detailed production plan, and engineering drawings were …

Dynamic Characterization Of Duroprotect, A Fiber-Reinforced Ballistics Composite, Ivy A. Turner

Honors Theses

Dynamic characterization of materials has become increasingly common, as it is important to understand how materials behave under sudden loads. Understanding these properties can aid in material selection for novel designs. DuroProtect, a fiber-reinforced ballistics composite developed by Rӧchling, was tested for its dynamic properties at high strain-rates. The Split Hopkinson Pressure Bar (SHPB) test was used to obtain dynamic properties at high strain-rates under compressive loading conditions. Tests were initially conducted to validate force equilibriums for each sample. The data measured from the strain gages mounted on the incident and transmission bars and the elastic wave propagation theories yields …

The Development Of All Solid-State Optical Cryo-Cooler, Junwei Meng

Optical Science and Engineering ETDs

This dissertation describes the development of an all solid-state optical cryo-cooler. Crystals of 10% wt. ytterbium-doped yttrium lithium fluoride (Yb³⁺:YLF) are used to cool an infrared HgCdTe sensor payload to an absolute temperature below 135 K, equivalent to delta T equal 138 K below ambient. This record level of cooling is accomplished with a single stage, in a completely vibration-free environment, with a corresponding cooling power of 190 mW. This milestone is made possible by the design and fabrication of an undoped YLF thermal link that efficiently shields the payload with a non-right angle kink from intense anti-Stokes …

Bulk Properties Correlated To The Hydrogen Bond Organization In Dendrimers, Hyperbranched Polymers, And Linear Polymers, Beibei Chen

Dissertations

Although a lot of research was conducted on dendritic polymers, our understanding of their structure-property is still limited. Our previous study, which focused on a family of dendritic polymers based on 2,2-bis(hydroxymethyl) propionic acid (bis-MPA) as a monomer, discovered unique hydrogen bond organizations contributed by their dendritic structures. However, the influence of the H-bond organization on bulk properties has yet to be understood. The goal of this dissertation is to elucidate the correlation between the H-bond organization with the dielectric and volumetric properties of bis-MPA based dendritic polymers, with an emphasis on developing a fundamental understanding of to what extent …

Optically Pumped Spin Polarization As A Probe Of Many-Body Thermalization, Daniela Pagliero, Pablo R. Zangara, Jacob Henshaw, Ashok Ajoy, Rodolfo H. Acosta, Jeffrey A. Reimer, Alexander Pines, Carlos A. Meriles

Publications and Research

Disorder and many body interactions are known to impact transport and thermalization in competing ways, with the dominance of one or the other giving rise to fundamentally different dynamical phases. Here we investigate the spin diffusion dynamics of ¹³C in diamond, which we dynamically polarize at room temperature via optical spin pumping of engineered color centers. We focus on low-abundance, strongly hyperfine-coupled nuclei, whose role in the polarization transport we expose through the integrated impact of variable radio-frequency excitation on the observable bulk ¹³C magnetic resonance signal. Unexpectedly, we find good thermal contact throughout the nuclear spin bath, …

Development Of Multi-Axial Fatigue Retrofits For Lock Gate Components, Logan Verkamp

Graduate Theses and Dissertations

Lock gates are essential infrastructure components to the United State (US) supply chain. They create large cost savings and environmental benefits when compared with traditional methods of transport (freight and rail). Because of the large quantity of goods and dependence on these shipping chains, the US economy can be drastically affected by an unexpected gate closure. Unfortunately, many lock gates within the US have reached or exceeded their designed life. Due to the intensity of cyclic loads and the environment, fatigue cracks have become a prominent issue. Developed cracks near the pintle region (a joint which the gate rotates and …