Engineering Commons^™

Evaluating The Thermoresponsive Properties Of Hydroxypropyl Cellulose Solutions For Smart Window Applications, Adam Reed

Williams Honors College, Honors Research Projects

With HVAC and building energy usage expected to increase, there is a strong need for autonomous thermal management solutions. In particular, there has been a growing interest in thermoresponsive (TR) smart windows that are activated by ambient temperature changes. Most TR smart windows contain a liquid solution between two panes. The goal of this research project was to develop a self-supporting smart window by forming a gel that maintained its TR properties. A gel is less prone to spilling in the case of window breakage. It was also desired to tune the phase transition to occur at environmentally relevant conditions …

Pulse Reverse Current Electrodeposited Tio2 Doped Ni-W Coating, Sydney Hughes

Williams Honors College, Honors Research Projects

Nickel-Tungsten (Ni-W) coatings via the pulse reverse current method have been under development as a potential replacement for typical Chromium/Cadmium coatings. To increase the effectiveness of Ni-W as a coating, dopants have been tested to decrease microcracks and pores and increase overall tribological performance. Previous research by Timken Engineered Surfaces Laboratory showed that Ni-W doped with TiO₂ nanoparticles had a positive effect on coating performance. The purpose of this study was to determine the ideal solution parameters (i.e. TiO₂ concentration, pH) to maximize the benefit of the dopant when samples are subjected to tribological testing. Here, solutions of …

Investigation Of Surface Charge Using Faraday Bucket Measurements: Analysis On Electrospun Polyvinylidene Fluoride Fiber Mats, Ryan Kantenwein

Williams Honors College, Honors Research Projects

Piezoelectric polymer materials such as polyvinylidene fluoride exhibit beneficial properties for use in personal protective equipment (PPE) against viral contaminants and other foreign microparticles. The electrospinning process of this material allows for surface charge to develop over a controlled surface area. Kynar 761 at 10 wt% demonstrates increased surface charge after withstanding a flow of aerated NaCl particles from a TSI 8130 instrument. Utilizing voltage measurements from a Faraday bucket, 18 wt% Kynar 761 and MG-15 exhibit surface charge when undergoing an electrospinning process; however, Kynar MG-15 displays lower charge values than that of Kynar 761. Several critical factors such …

Increasing The Corrosion Protection Of Aisi 1008 Carbon Steel By Surface Treatment With Unmodified And Benzotriazole Modified Sol-Gel Films, Shane Thomas Kelliher

Williams Honors College, Honors Research Projects

The corrosion performance of sol-gel coated AISI 1008 carbon steel was investigated in 3.5 wt% NaCl solutions of pH 7, 9, and 12 using electrochemical measurements. A corrosion inhibitor, benzotriazole (BTA) was added to the sol-gel mixture and tested as a second, modified sol-gel coating. Sol-gel films adhered evenly to metal samples and were characterized by FTIR spectroscopy. Electrochemical Impedance Spectroscopy (EIS) showed an increase in polarization resistance from blank to sol-gel coated samples (600-18,800,000 ohms). Cyclic polarization (CPP) curves showed positive hysteresis loops for blank and unmodified sol-gel coated samples which increased at high pH following the backward potential …

Design And Analysis Of One-Piece 10” Carbon Fiber Wheels For Zips Racing Zr20 Formula Sae Racecar, Patrick Kruse, Henry J. Wathen, Jordan J. Hyde, Nicholas D. Dobben, Jordan D. Blake

Williams Honors College, Honors Research Projects

Reducing the weight of a vehicle in racing can substantially improve the vehicle dynamics and general performance capabilities. More specifically, the reduction of the unsprung corner weight can provide noticeable performance gains in handling and responsiveness, leading to a quicker, more agile car due to a lower yawing moment of inertia. Unsprung weight reduction also improves the car’s ability to maintain contact between the tires and the road surface for a more consistent grip. In this project we identified the loads that act on the wheel rims according to the data collected from the sensors in the car’s suspension, and …

Tabletop Dome Tester, Dylan Davis

Williams Honors College, Honors Research Projects

The project for the dome tester stand is a continuation from a group of four that worked on the stand in Spring of 2020. The project itself is based around the Erichsen Cupping test to test the material properties, in our application specifically, observing the forming limits of strain in deep drawing applications of sheet metal. Testing pieces in varying lengths from 4” x 4” squares to 4” x 0.5” strips to the depth that necking begins on the piece to determine the limit before cracks appear using a hemispherical punch to draw the material sample clamped between two dies. …

Combined Puncture And Cutting Of Soft-Coated Fabrics By A Pointed Blade: Energy, Force, And Stress Failure Criteria, Ennouri Triki, Chantal Gauvin

Études primaires

Soft elastomer-coated fabrics are widely used in engineering and protective applications. Puncture cutting by sharp-tipped objects is one of the most common failure modes of protective gloves made of coated fabrics. In order to investigate the puncture-cutting process of soft elastomer-coated fabrics, we studied the mechanisms and mechanics of pointed-blade insertion into specimens cut out from four protective gloves. Experimental and analytical analyses showed that total energy and critical puncture-cutting force calculated analytically are both able to predict the puncture-cutting resistance of soft elastomer-coated fabrics measured experimentally. Total energy is obtained from the relationship between the puncture-cutting work and the …

In Depth Characterisation Of The Biomolecular Coronas Of Polymer Coated Inorganic Nanoparticles With Differential Centrifugal Sedimentation, André Perez-Potti, Hender Lopez, Beatriz Pelaz, Abuelmagd Abdelmonem, Mahmoud G. Soliman, Ingmar Schoen, Philip M. Kelly, Kenneth A. Dawson, Wolfgang J. Parak, Zeljka Krpetic, Marco P. Monopoli

Articles

Advances in nanofabrication methods have enabled the tailoring of new strategies towards the controlled production of nanoparticles with attractive applications in healthcare. In many cases, their characterisation remains a big challenge, particularly for small-sized functional nanoparticles of 5 nm diameter or smaller, where current particle sizing techniques struggle to provide the required sensitivity and accuracy. There is a clear need for the development of new reliable characterisation approaches for the physico-chemical characterisation of nanoparticles with significant accuracy, particularly for the analysis of the particles in the presence of complex biological fluids. Herein, we show that the Differential Centrifugal Sedimentation can …

Studies In Additive Manufacturing Techniques For Pulsed Fusion Experiments, Michael Canary

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Application Of Laser Assisted Ultrasonic Nanocrystal Surface Modification On Aluminum And 3d Printed Titanium, Eman Hassan, Thomas Crouse

Williams Honors College, Honors Research Projects

A novel surface treatment, laser assisted ultrasonic nanocrystal surface modification (LA-UNSM), has proved effective in increasing surface hardness, and fatigue life. The objective of this research is to determine the effectiveness of this process on components created with additive manufacturing. To accomplish this, we investigated the effectiveness of LA-UNSM treatment on aluminum, a common 3d printed metal, and the effectiveness of LA-UNSM processing on 3d printed titanium. We first conducted our own literature review to assess the practicality of using this same treatment on aluminum. We then treated traditionally manufactured aluminum at varying levels of laser intensity to determine if …

Jominy Hardenability Tester Redesign, Dennis Kopacz, Shadoe Beatty, Thomas Benenati, Jared Mclean, Matthew Yokosuk

Williams Honors College, Honors Research Projects

Our project is Redesigning a Hardenability Tester. The goal of this project is to figure out how to incorporate an intensive quenching system to the current design from last years group. An intensive quench is a new system that is safer to harden steel and it hardens steel more effectively than other quenching processes. This will be achieved through testing the initial design to make sure it is able to run. After that as a group we will take this system through a design process to introduce a safe process of intensive quenching to the tester.

Exploring Rapid Solidification And Equal Channel Angular Pressing In The Fabrication Of Mg-Based Alloys For Medical Applications, Emily Tom

Dissertations, Master's Theses and Master's Reports

The development of magnesium bioresorbable implants has become increasingly popular due to the increased need for temporary implants and magnesium’s excellent biocompatibility and suitable elastic modulus. Even though magnesium is an excellent candidate, when alloyed with other metals magnesium’s corrosion rate becomes too rapid for bioresorbable medical applications. The investigation into novel processing techniques to control the formation of precipitates to improve mechanical strength and ductility as well as corrosion rates has become of interest. This work investigates the combination of two nonequilibrium processing techniques, rapid solidification (RS) and equal channel angular pressing (ECAP), and the effects it has on …

Microstructural And Chemical Characterization Of A Purple Pigment From A Faiyum Mummy Portrait, Glenn Gates, Yaqiao Wu, Jatuporn Burns, Jennifer Watkins, Darryl P. Butt

Materials Science and Engineering Faculty Publications and Presentations

Results are presented from analyses that were conducted to explain the presence of chromium, detected noninvasively using energy-dispersive X-ray fluorescence (XRF), in the unusually large (2-3mm diameter) rough gem-like purple pigment particles in the paint used for a Faiyum mummy portrait. An approximately 50 μm diameter particle of the chromium-containing purple pigment was extracted from the Portrait of a Bearded Man, dated to Roman Imperial Egypt in the second century, circa 170-180 CE, accession #32.6 in the Walters Art Museum collection. The particle was characterized using energy-dispersive X-ray fluorescence analysis, electron microscopy, diffraction, and atom probe tomography. It is …

Influence Of The Inas Coverage On The Performance Of Submonolayer-Quantum-Dot Infrared Photodetectors Grown With A (2×4) Surface Reconstruction, Ahmad Alzeidan, Tiago F. De Cantalice, Kevin D. Vallejo, Paul J. Simmonds, Alain A. Quivy

Materials Science and Engineering Faculty Publications and Presentations

Two infrared photodetectors based on submonolayer quantum dots, having a different InAs coverage of 35% and 50%, were grown, processed and tested. The detector with the larger coverage yielded a specific detectivity of 1.13×10 ¹¹ cm Hz ^1/2 W ^-1 at 12K, which is among the highest values reported in the literature for that kind of device.

Development Of An Undergraduate Welding Laboratory For Research And Education, Hamid Eisazadeh, Alok K. Verma

Engineering Technology Faculty Publications

The shortage of welders in Hampton Roads area, where many shipyards are located, is becoming severe for shipbuilding in coming years. Many welding engineers graduated from universities located out of state, tend to go back to companies near their home, after receiving couple years of welding experience at Hampton Roads shipyards. Therefore, it is critical to train local welders. In order to address the welding workforce needs of Hampton Roads, the Department of Engineering Technology at Old Dominion University has recently launched an initiative for developing a laboratory for welding processes (LWP) for supporting educational and research activities in its …

Development Of An Injectable Methylcellulose Hydrogel System For Nucleus Pulposus Repair And Regeneration, Nada A. Haq-Siddiqi

Dissertations and Theses

Low back pain is the most common cause of disability in the world and is often caused by degeneration or injury of the intervertebral disc (IVD). The IVD is a complex, fibrocartilaginous tissue that allows for the wide range of spinal mobility. Disc degeneration is a progressive condition believed to begin in the central, gelatinous nucleus pulposus (NP) region of the tissue, for which there are few preventative therapies. Current therapeutic strategies include pain management and exercise, or surgical intervention such as spinal fusion, none of which address the underlying cause of degeneration. With an increasingly aging population, the socioeconomic …

Development Of Light Actuated Chemical Delivery Platform On A 2-D Array Of Micropore Structure, Hojjat Rostami Azmand, Hojjat Rostami Azmand

Dissertations and Theses

Localized chemical delivery plays an essential role in the fundamental information transfers within biological systems. Thus, the ability to mimic the natural chemical signal modulation would provide significant contributions to understand the functional signaling pathway of biological cells and develop new prosthetic devices for neurological disorders. In this paper, we demonstrate a light-controlled hydrogel platform that can be used for localized chemical delivery in a high spatial resolution. By utilizing the photothermal behavior of graphene-hydrogel composites confined within micron-sized fluidic channels, patterned light illumination creates the parallel and independent actuation of chemical release in a group of fluidic ports. The …

Molecular To Macroscopic Understanding Of Chloroaluminate Anion Intercalation In Rechargeable Aluminum-Graphite Batteries, Jeffrey Xu

Dissertations and Theses

Today’s global energy challenges pose an urgent need to electrify transportation and better store intermittent renewable energy sources (e.g., solar and wind energy). For such large-scale battery applications, aluminum batteries are a promising “beyond lithium-ion” technology due to the high volumetric capacity, earth abundance, low-cost, and inherent safety of aluminum metal. However, there are very few compatible positive electrode materials that exhibit high energy density and cycling stability, in part due to the challenges of electrochemically intercalating highly charged Al³⁺ cations. Recently, graphite has been demonstrated as a promising positive electrode material in non-aqueous rechargeable aluminum batteries, which store …

Effects Of Corrosion On The Sers Activity And Optical Response Of Silver Nanorods, Christopher J. Mealer

UNF Graduate Theses and Dissertations

The nanoscience and nanotechnology community have a common goal in better understanding the surfaced enhanced Raman scattering (SERS) that occurs due to laser plasmon resonance in conjunction with metal enhanced substrates. Metallic nanostructures, such as silver (Ag) nanorods, are widely used in biological and chemical sensing applications that rely on the measurement of subtle changes in the optical response of the nanostructures in the presence of a target agent. The optical response of Ag nanorods and most other metallic nanostructures is highly sensitive to morphology and surface chemical termination. In pristine condition, the optical properties of Ag nanorods and other …

Experimental Exploration Of Shared Magnetic Phases Between Diverse Systems Of Iron-Pnictide Superconductors, Ryan Scott Stadel

Graduate Research Theses & Dissertations

The exciting field of iron-pnictide superconductors offers unique opportunities for studying the relationship between magnetism and unconventional superconductivity. This is vital to developing an understanding of the microscopic origin of high-temperature superconductivity, which is itself an important step in harnessing such a potentially revolutionary technology.

Polycrystalline and crystalline samples are synthesized over a diverse collection of related iron-pnictide systems including (Ca,Sr,Ba)1-xNaxFe2As2, Ba(Fe1-xCox)2As2 (122s), and LaFeAs1-xPxO, and TbFeAs1-xPxO (1111s). These compounds are characterized through various types of neutron and x-ray diffraction on multiple instruments, as well as muon spin resonance, and magnetic susceptibility measurements.

A thorough investigation into the conditions under …

Morphology Control Of One-Dimensional Gallium Nitride Nanostructures By Modulating The Crystallinity Of Sacrificial Gallium Oxide Templates, Yun Taek Ko, Mijeong Park, Jingyeong Park, Jaeyun Moon, Yong Ho Choa, Young In Lee

Mechanical Engineering Faculty Research

In this study, we demonstrated a method of controllably synthesizing one-dimensional nanostructures having a dense or a hollow structure using fibrous sacrificial templates with tunable crystallinity. The fibrous ga2o3 templates were prepared by calcining the polymer/gallium precursor nanofiber synthesized by an electrospinning process, and their crystallinity was varied by controlling the calcination temperature from 500oC to 900oC. gaN nanostructures were transformed by nitriding the ga2o3 nanofibers using NH3 gas. All of the transformed gaN nanostructures maintained a one-dimensional structure well and exhibited a diameter of about 50 nm, but their morphology was clearly distinguished according to the crystallinity of the …

Direct Energy Deposition Of Mo Powder Prepared By Electrode Induction Melting Gas Atomization, Goo Won Roh, Eun Soo Park, Jaeyun Moon, Hojun Lee, Jongmin Byun

Mechanical Engineering Faculty Research

Molybdenum (Mo) is used to form a barrier layer for metal wiring in displays or semiconductor devices. Recently, researches have been continuously attempted to fabricate Mo sputtering targets through additive manufacturing. in this study, spherical Mo powders with an average particle size of about 37 um were manufactured by electrode induction melting gas atomization. Subsequently, Mo layer with a thickness of 0.25 mm was formed by direct energy deposition in which the scan speed was set as a variable. According to the change of the scan speed, pores or cracks were found in the Mo deposition layer. Mo layer deposited …

Fabrication Of Nanoporous Materials For Applications Under Extreme Environments, Maria Kosmidou

Theses and Dissertations--Chemical and Materials Engineering

The study of nanoporous materials has become a key aspect of nanotechnology due to their high surface-area-to-volume ratio, arising from the small size ligaments and pores that form the structure. Sensing, catalysis, micro-electromechanical systems (MEMS), medical applications, and materials for radiation environments are some of the applications for which nanoporous materials are considered great candidates. This work, performed at the Ion Beam Laboratory (IBL) at Sandia National Laboratories (SNL), examines the effect of heavy and light ion irradiation exposure on nanoporous Au. Radiation damage accumulation is observed with real-time recording of the creation, migration, and removal of the radiation-induced defects …

Electrochemical Performance Of Biomass-Derived Activated Carbon Supercapacitor Under Compression, Yulin Zhang

Theses and Dissertations--Chemical and Materials Engineering

Supercapacitors are important energy storage device of high-power density, fast charge/discharge rate, environmental friendliness and long service life. Currently, flexible supercapacitors have attracted widespread interest in academia and industry. Supercapacitors under the action of external force will inevitably cause structural changes, performance degradation and even loss of energy storage and supply functionalities. As the most abundant renewable resource so far, biomass is an important energy source for human survival and development. Most electrode materials for supercapacitors are porous activated carbons, which can be derived from abundant renewable biomass, contributing to the sustainable development of society and environmental protection. This thesis …

The Development Of Structural Hollow Carbon Fibers From A Multifilament Segmented Arc Spinneret: Precursors, Oxidation, And Carbonization, Elizabeth Ashley Morris

Theses and Dissertations--Chemical and Materials Engineering

Carbon fiber is an ideal material for structural applications requiring high strength and stiffness and low weight. Yet it has seen only incremental improvements in properties over the last few decades. Carbon fibers remain limited in attaining their theoretical tensile strength and modulus, largely due to defects in their structure, some of which stem from the fiber production process itself. Through the mitigation of defect formation as well as approaches to decrease fiber linear density, it is hypothesized that carbon fiber with enhanced specific properties, including specific strength and modulus, could be produced which would significantly propel its unique capabilities. …

Theoretical Analysis Of Experimental Data Of Sodium Diffusion In Oxidized Molybdenum Thin Films, Orlando Ayala, Benjamin Belfore, Tasnuva Ashrafee, John Akwari, Grace Rajan, Shankar Karki, Deewakar Poudel, Sylvain Marsillac

Engineering Technology Faculty Publications

In this work, the diffusion process of sodium (Na) in molybdenum (Mo) thin films while it was deposited on soda lime glass (SLG) was studied. A small amount of oxygen was present in the chamber while the direct-current (DC) magnetron sputtering was used for the deposition. The substrate temperatures were varied to observe its effect. Such molybdenum films, with or without oxidations, are often used in thin film solar cells, either as back contact or as hole transport layers. Secondary ion mass spectrometry (SIMS) was used to quantify the concentration of the species. A grain diffusion mechanistic model incorporating the …

Detection Of Subsurface, Nanometer-Scale Crystallographic Defects By Nonlinear Light Scattering And Localization, Farbod Shafiei, Tommaso Orzali, Alexey Vert, Mohammad-Ali Miri, Pui Yee Hung, Man Hoi Wong, Andrea Alù, Gennadi Bersuker, Michael C. Downer

Publications and Research

Heteroepitaxial crystalline films underlie many electronic and optical technologies but are prone to forming defects at their heterointerfaces. Atomic-scale defects such as threading dislocations that propagate into a film impede the flow of charge carriers and light degrading electrical/optical performance of devices. Diagnosis of subsurface defects traditionally requires time-consuming invasive techniques such as cross-sectional transmission electron microscopy. Using III–V films grown on Si, noninvasive, bench-top diagnosis of subsurface defects have been demonstrated by optical second-harmonic scanning probe microscope. A high-contrast pattern is observed of subwavelength “hot spots” caused by scattering and localization of fundamental light by defect scattering sites. Size …

Perovskite Thin Films Annealed In Supercritical Fluids For Efficient Solar Cells, Gilbert Annohene

Theses and Dissertations

In the field of photovoltaics, scientists and researchers are working fervently to produce a combination of efficient, stable, low cost and scalable devices. Methylammonium lead trihalide perovskite has attracted intense interest due to its high photovoltaic performance, low cost, and ease of manufacture. Their high absorption coefficient, tunable bandgap, low-temperature processing, and abundant elemental constituent provide innumerable advantages over other thin film absorber materials. Since the perovskite film is the most important in the device, morphology, crystallization, compositional and interface engineering have been explored to boost its performance and stability. High temperatures necessary for crystallization of organic-inorganic hybrid perovskite films …

Accident Tolerant Fuels Claddings And The Evolution Of Their Surface Characteristics Under Critical Heat Flux, Rajnikant V. Umretiya

Theses and Dissertations

Enhanced Accident Tolerant Fuels (ATFs) systems for light water reactors require higher temperature oxidation resistance in steam environments than the current UO₂ – zirconium fuel system. Investigating the ATF materials’ surface properties is needed as they have evidenced to affect the Critical Heat Flux (CHF), which is an important parameter of the thermal-hydraulic performance required to provide safety margins. In this dissertation, the surface properties of FeCrAl alloys (APMT and C26M), Zircaloy-2, Zircaloy-4, and Cr-coating on Zircaloy-4 substrates produced by Physical Vapor Deposition (PVD) and Cold Spray (CS) were investigated according to their chemistry, topography, and wettability. The static …

Coaxially Electrospun Fibrous Polymer Scaffolds For Tissue Regeneration And Drug Delivery, Matthew Michael Kleszynski

Graduate Research Theses & Dissertations

A biomaterial is a substance that is specifically engineered to take on a role within the body, either alone or in conjunction with other materials, with the purpose of influencing the body. Using Polymers as a biomaterial is an exciting field of study that has the potential to further our abilities to help those in need. Creating composite nanofibrous scaffolds composed of hydrophobic and hydrophilic polymers may outperform structures made of a single polymer in both in vitro and in vivo environments. Hydrophilicity governs the behavior of polymers in the body and has influence over the mechanical properties of the …