Open Access. Powered by Scholars. Published by Universities.®

Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Materials Science and Engineering

Institution
Keyword
Publication Year
Publication
Publication Type
File Type

Articles 11041 - 11070 of 16715

Full-Text Articles in Engineering

Electrocatalytic Activity Of Palladium Nanocatalysts Supported On Carbon Nanoparticles In Formic Acid Oxidation, Jie Huang, Zhiyou Zhou, Yang Song, Xiongwu Kang, Ke Liu, Wancheng Zhou, Shaowei Chen Dec 2012

Electrocatalytic Activity Of Palladium Nanocatalysts Supported On Carbon Nanoparticles In Formic Acid Oxidation, Jie Huang, Zhiyou Zhou, Yang Song, Xiongwu Kang, Ke Liu, Wancheng Zhou, Shaowei Chen

Journal of Electrochemistry

Palladium nanostructures were deposited onto carbon nanoparticle surface by a chemical reduction method. Transmission electron microscopic studies showed that whereas the resulting metal-carbon (Pd-CNP) nanocomposites exhibited a diameter of 20 to 30 nm, the metal components actually showed a cauliflower-like surface morphology that consisted of numerous smaller Pd nanoparticles (3 to 8 nm). Electrochemical studies showed that the effective surface area of the Pd-CNP nanoparticles was about 40% less than that of Pd black, possibly because the Pd nanoparticles were coated with a layer of carbon nanoparticles; yet, the Pd-CNP nanocomposites exhibited marked enhancement of the electrocatalytic activity in formic …

Go to article

Adsorption And Electrooxidation Of Carbon Monoxide On Platinum Surfaces Modified With Sulfur, A. Mattox Mathew, W. Henney Matthew, Johnson Adam, Zou Shouzhong Dec 2012

Adsorption And Electrooxidation Of Carbon Monoxide On Platinum Surfaces Modified With Sulfur, A. Mattox Mathew, W. Henney Matthew, Johnson Adam, Zou Shouzhong

Journal of Electrochemistry

Adsorbed sulfur is commonly considered as a reaction poison. However, small amounts of sulfur on platinum significantly increase the surface reactivity toward carbon monoxide (CO) electrooxidation. For the solution CO oxidation, the onset potential was shifted up to over 300 mV negative to that on S-free surface, and the extent of the negative potential shift increases with the sulfur coverage (Xs) up to about 0.6. The enhanced CO oxidation also depends on the solution pH. For the adsorbed CO, at low sulfur coverages (Xs < 0.3), the oxidation peak potential is about 40 mV negative to that of the corresponding clean Pt. However, at higher coverages, the peak potential is about 30 mV more positive. Surface-enhanced Raman spectra show that the adsorption of sulfur significantly redshifts the Pt-CO stretching frequency. These observations are explained by the weakening of the Pt-CO bond and the hindrance of CO diffusion by Sads.

Go to article

Kinetic Study Of Photoelectrochemical Oxidation Of Lignin Model Compounds On Tio2 Nanotubes, Min Tian, Daniel Liba, Aicheng Chen Dec 2012

Kinetic Study Of Photoelectrochemical Oxidation Of Lignin Model Compounds On Tio2 Nanotubes, Min Tian, Daniel Liba, Aicheng Chen

Journal of Electrochemistry

In this study, TiO2 nanotubes were prepared via the electrochemical oxidation of titanium substrates in a non-aqueous electrolyte and their morphology and microstructures were examined by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The photoelectrochemical oxidation of two lignin model compounds, 1-(3,4-dimethoxyphenoxy)-2-(2-methoxyphenoxy)-1,3-propanediol (DMP) and 3-hydroxy-1-(3,4-dimethoxyphenoxy)-2-(2-methoxyphenoxy)-1,3-propanone (HDM), was investigated. A new band appeared at ~304 nm during the photoelectrochemical oxidation of DMP. The rate of DMP intermediate formation was amplified with the increase of initial concentrations, while it was diminished with increased temperature. Despite the similarity in structure between HDM and DMP, there are only small increases in absorbance …

Go to article

Ternary Alloy Electrocatalysts For Oxygen Reduction Reaction, Jin Luo, Lefu Yang, Binghui Chen, Chuanjian Zhong Dec 2012

Ternary Alloy Electrocatalysts For Oxygen Reduction Reaction, Jin Luo, Lefu Yang, Binghui Chen, Chuanjian Zhong

Journal of Electrochemistry

Proton exchange membrane fuel cell represents an important electrochemical energy conversion device with many attractive features in terms of efficiency of energy conversion and minimization of environmental pollution. However, the large overpotential for oxygen reduction reaction at the cathode and the low activity, poor durability and high cost of platinum-based catalysts in the fuel cells constitute a focal point of major barriers to the commercialization of fuel cells. The development of nanostructured catalysts shows promises to addresses some of the challenging problems. The ability to engineer the composition and nanostructure of nanoalloy catalysts is important for developing active, robust and …

Go to article

Grain Size And Texture Effects On Deformation Behavior Of Az31 Magnesium Alloy, W. Yuan, R. S. Mishra Dec 2012

Grain Size And Texture Effects On Deformation Behavior Of Az31 Magnesium Alloy, W. Yuan, R. S. Mishra

Materials Science and Engineering Faculty Research & Creative Works

Cold rolled AZ31 magnesium alloy sheet was subjected to friction stir processing to generate four average grain sizes ranging from 0.8 to 9.6 μm. the processed material exhibited a strong basal fiber texture with the c-axis tilted about 35-55° towards the processing direction. the grain size and texture dependence of mechanical behavior were evaluated by using tensile testing along two orthogonal directions. Remarkably high ductility of ~65% was achieved in relatively coarse-grained material that fractured without developing necking when tested in the processing direction. the ductility decreased significantly to ~10% for ultrafine grained material as the tensile yield strength increased …

Go to article

High Performance Low Temperature Solid Oxide Fuel Cells With Novel Electrode Architecture, Yu Chen, Qian Liu, Zhibin Yang, Fanglin Chen, Minfang Han Dec 2012

High Performance Low Temperature Solid Oxide Fuel Cells With Novel Electrode Architecture, Yu Chen, Qian Liu, Zhibin Yang, Fanglin Chen, Minfang Han

Faculty Publications

In this study, we have fabricated high performance low temperature solid oxide fuel cells (LT-SOFCs) with both acicular anodes and cathodes with thin Gd-doped ceria (GDC) electrolyte film. The acicular Ni-Gd0.1Ce0.9O2−δ (Ni-GDC) anode was prepared using freeze drying tape casting, while the hierarchically porous cathode with nano-size Sm0.5Sr0.5CoO3 (SSC) particles covering an acicular GDC skeleton was prepared by a combination of freeze drying tape casting and self-rising approaches. The acicular electrodes with 5–200 μm pores/channels enhance mass transport, while SSC particles of about 50 nm in the cathode promote …

Go to article

Epr And Endor Studies Of Point Defects In Lithium Tetraborate Crystals, Douglas A. Buchanan Dec 2012

Epr And Endor Studies Of Point Defects In Lithium Tetraborate Crystals, Douglas A. Buchanan

Theses and Dissertations

Lithium tetraborate (Li2B4O7 or LTB) is a promising material for both radiation dosimetry and neutron detection applications. LTB crystals can be grown pure or doped with different impurities including transition-metal and rare-earth ions. Research in this dissertation focuses on undoped LTB crystals and LTB crystals doped with copper and silver. Electron paramagnetic resonance (EPR) and electron-nuclear double resonance (ENDOR) are used to characterize point defects in the lithium tetraborate crystals. Thermoluminescence (TL), photoluminescence (PL), photoluminescence excitation (PLE), and optical absorption (OA) are also used. An intrinsic hole trap associated with lithium vacancies is characterized with …

Go to article

Effects Of Crossflow Velocity And Transmembrane Pressure On Microfiltration Of Oil-In-Water Emulsions, Nikolai V. Priezjev, Tohid Darvishzadeh Dec 2012

Effects Of Crossflow Velocity And Transmembrane Pressure On Microfiltration Of Oil-In-Water Emulsions, Nikolai V. Priezjev, Tohid Darvishzadeh

Mechanical and Materials Engineering Faculty Publications

This study addresses the issue of oil removal from water using hydrophilic porous membranes. The effective separation of oil-in-water dispersions involves high flux of water through the membrane and, at the same time, high rejection rate of the oil phase. The effects of transmembrane pressure and crossflow velocity on rejection of oil droplets and thin oil films by pores of different cross-section are investigated numerically by solving the Navier-Stokes equation. We found that in the absence of crossflow, the critical transmembrane pressure, which is required for the oil droplet entry into a circular pore of a given surface hydrophilicity, agrees …

Go to article

Recovery Of Metallic Materials From Printed Wiring Boards By Green Pyrolysis Process, Alex Luyima, Lifeng Zhang, Jaan Kers, Viktor Laurmaa Dec 2012

Recovery Of Metallic Materials From Printed Wiring Boards By Green Pyrolysis Process, Alex Luyima, Lifeng Zhang, Jaan Kers, Viktor Laurmaa

Materials Science and Engineering Faculty Research & Creative Works

Currently, the main options for the treatment of electronic waste are involved in reuse, remanufacturing, and recycling, as well as incineration and land filling. Recycling of e-waste can be broadly divided into three major steps: (a) disassembly: selectively disassembly, targeting on singling out hazardous or valuable components for special treatment, is an indispensable process in recycling of e-waste; (b) upgrading: using mechanical processing and/or metallurgical processing to up-grade desirable materials content, i. e. preparing materials for refining process; (c) refining: in the last step, recovered materials are retreated or purified by using chemical (metallurgical) processing so as to be acceptable …

Go to article

Analysis Of Solid Oxide Fuel Cell-Gas-Turbine Hybrid System Technology For Use In Aircraft, Jeremy Milliner, Rory Roberts Dec 2012

Analysis Of Solid Oxide Fuel Cell-Gas-Turbine Hybrid System Technology For Use In Aircraft, Jeremy Milliner, Rory Roberts

Explorations – The Journal of Undergraduate Research, Scholarship and Creativity at Wright State

Solid oxide fuel-cell-gas-turbine (SOFC/GT) hybrid systems are a technology that provides a more efficient source of energy for a variety of uses. One potential use is to provide more efficient energy to aircraft, which is the subject of this work. Potential applications to aircraft and results from a computer model of a SOFC/GT are presented here.

Go to article

Quantum Dot Deposition Into Pdms And Application Onto A Solar Cell, Christopher Marcus Botros, Richard N. Savage Dec 2012

Quantum Dot Deposition Into Pdms And Application Onto A Solar Cell, Christopher Marcus Botros, Richard N. Savage

Master's Theses

Research to increase the efficiency of conventional solar cells is constantly underway. The goal of this work is to increase the efficiency of conventional solar cells by incorporating quantum dot (QD) nanoparticles in the absorption mechanism. The strategy is to have the QDs absorb UV and fluoresce photons in the visible region that are more readily absorbed by the cells. The outcome is that the cells have more visible photons to absorb and have increased power output. The QDs, having a CdSe core and a ZnS shell, were applied to the solar cells as follows. First, the QDs were synthesized …

Go to article

An Experimental Investigation On The Trailing Edge Cooling Of Turbine Blades, Zifeng Yang, Hui Hu Dec 2012

An Experimental Investigation On The Trailing Edge Cooling Of Turbine Blades, Zifeng Yang, Hui Hu

Mechanical and Materials Engineering Faculty Publications

An experimental study was conducted to quantify the flow characteristics of the wall jets pertinent to trailing edge cooling of turbine blades. A high-resolution stereoscopic particle image velocimetry (PIV) system was used to conduct detailed flow field measurements to quantitatively visualize the evolution of the unsteady vortices and turbulent flow structures in the cooling wall jet streams and to quantify the dynamic mixing process between the cooling jet stream and the mainstream flows. The detailed flow field measurements were correlated with the adiabatic cooling effectiveness maps measured by using pressure sensitive paint (PSP) technique to elucidate underlying physics in order …

Go to article

Silica Nanoparticle-Based Coatings With Superhydrophilic And Superhydrophobic Properties, Robert Andrew Fleming Dec 2012

Silica Nanoparticle-Based Coatings With Superhydrophilic And Superhydrophobic Properties, Robert Andrew Fleming

Graduate Theses and Dissertations

Superhydrophilic and superhydrophobic surfaces have potential for implementation into a variety of fields, including self-cleaning surfaces, anti-fogging transparent materials, and biomedical applications. In this study, sandblasting, oxygen plasma treatments, silica nanoparticle films, and a low surface energy fluorocarbon film were employed to change the natural surface wettability of titanium, glass, and polyethylene terephthalate (PET) substrates, with an aim to produce superhydrophilic and superhydrophobic behavior. The effects of these surface modifications are characterized by water contact angles (WCAs), surface wetting stability, surface morphology and roughness, surface elemental composition, and optical transmittance measurements. The results show that stable superhydrophilic and superhydrophobic surfaces …

Go to article

Design, Fabrication, Testing Of Cnt Based Isfet And Characterization Of Nano/Bio Materials Using Afm, Zhuxin Dong Dec 2012

Design, Fabrication, Testing Of Cnt Based Isfet And Characterization Of Nano/Bio Materials Using Afm, Zhuxin Dong

Graduate Theses and Dissertations

A combination of Carbon Nanotubes (CNTs) and Ion Selective Field Effect Transistor (ISFET) is designed and experimentally verified in order to develop the next generation ion concentration sensing system. Micro Electro-Mechanical System (MEMS) fabrication techniques, such as photolithography, diffusion, evaporation, lift-off, packaging, etc., are required in the fabrication of the CNT-ISFET structure on p-type silicon wafers. In addition, Atomic Force Microscopy (AFM) based surface nanomachining is investigated and used for creating nanochannels on silicon surfaces. Since AFM based nanomanipulation and nanomachining is highly controllable, nanochannels are precisely scratched in the area between the source and drain of the FET where …

Go to article

Investigation On Thermo-Mechanical Instability Of Porous Low Dielectric Constant Materials, Emil Hyunbae Zin Dec 2012

Investigation On Thermo-Mechanical Instability Of Porous Low Dielectric Constant Materials, Emil Hyunbae Zin

Material Science and Engineering Dissertations - Archive

This study investigates the structural stability of porous low dielectric constant materials (PLK) under thermal and mechanical load and the influence of contributing factors including porosity as intrinsic factor and plasma damage and moisture absorption as extrinsic factors on thermo-mechanical instability of PLK in advanced Cu/PLK interconnects. For this purpose, a ball indentation creep test technique was developed to examine the thermal and mechanical instability of PLK at relevant load and temperature conditions in the interconnect structure. Our exploration with the ball indentation creep test found that PLK films plastically deforms with time, indicating that viscoplastic deformation does occur under …

Go to article

First-Principles Studies On N-Type And P-Type Doping In Cuprous Oxide, Qiong Bai Dec 2012

First-Principles Studies On N-Type And P-Type Doping In Cuprous Oxide, Qiong Bai

Material Science and Engineering Dissertations - Archive

We have performed studies on n-type and p-type cuprous oxide with and without doping by first principles methods. Generalized Gradient Approximation (GGA) is used for the geometry optimization. The total energy and the final electronic structure calculations are conducted using the nonlocal screened Heyd-Scuseria-Ernzerhof (HSE) hybrid density functionals approach for cuprous oxide. The HSE hybrid density functionals overcome the shortcoming of GGA, which gives a much reliable value of the band gap. The formation energies of native point defects in undoped cuprous oxide have been studied by HSE hybrid functional theory in two conditions, which are vacuum based condition and …

Go to article

Properties Of Concrete With Tire Derived Aggregate And Crumb Rubber As A Ligthweight Substitute For Mineral Aggregates In The Concrete Mix, Gideon Momanyi Siringi Dec 2012

Properties Of Concrete With Tire Derived Aggregate And Crumb Rubber As A Ligthweight Substitute For Mineral Aggregates In The Concrete Mix, Gideon Momanyi Siringi

Material Science and Engineering Dissertations - Archive

Scrap tires continue to be a nuisance to the environment and this research proposes one way of recycling them as a lightweight aggregate which can substitute for mineral aggregates in concrete. Aggregates derived from scrap tires are often referred to as Tire Derived Aggregate (TDA). First, the focus is how much mineral aggregate can be replaced by these waste tires and how the properties of concrete are affected with the introduction of rubber. This is being mindful of the fact that for a new material to be acceptable as an engineering material, its properties and behavior has to be well …

Go to article

Growth Mechanism And Interface Effects On Microstructure Of Perovskite-Type Barium Titanate-Based Epitaxial Films, Jie He Dec 2012

Growth Mechanism And Interface Effects On Microstructure Of Perovskite-Type Barium Titanate-Based Epitaxial Films, Jie He

Material Science and Engineering Dissertations - Archive

This work was motivated and focused on the growth mechanism, microstructures and interfaces of barium titanate, BaTiO3 (BTO), based epitaxial thin films. Transimission electron microscopy (TEM), high resolution TEM (HRTEM), electron diffraction (ED) have been mainly employed in this study for microstructure investigations of BTO-based epitaxial thin films with the assistance of other materials characterization methods, such as X-ray diffraction (XRD), atomic force microscopy (AFM), Nanoindentation testing, etc. As a basic studying model, epitaxial BTO films were first deposited on the (001) MgO substrate using RF magnetron sputtering to provide fundamental knowledge of the film growth for BTO based thin …

Go to article

Syntheses, Characterization, And Applications Of Injectable Citrate-Based Mussel-Inspired Biodegradable Adhesive (Icmba) Polymers And Hydrogels, Mohammadreza Mehdizadeh Dec 2012

Syntheses, Characterization, And Applications Of Injectable Citrate-Based Mussel-Inspired Biodegradable Adhesive (Icmba) Polymers And Hydrogels, Mohammadreza Mehdizadeh

Material Science and Engineering Dissertations - Archive

Tissue adhesives are increasingly gaining more popularity in various areas of biomedical applications. They are utilized as surgical adhesives, as a replacement or adjunct to conventional wound closure and bleeding control techniques such as suturing, as well as in other applications such as tissue engineering and drug delivery.Unfortunately, the existing surgical adhesives are not ideal for wet tissue adhesion required in many surgeries such as those for internal organs. Developing surgical adhesives with strong wet tissue adhesion, controlled degradability and mechanical properties, and excellent biocompatibility has been a significant challenge. Herein, learning from nature, we report a one-step synthesis of …

Go to article

Prediction Of Compressive Creep Bhaviour In Flexible Polyurethane Foam Over Long Time Scales And At Elevated Temperatures, Conor Briody, Barry Duignan, Stephen Jerrams, Stephen Ronan Dec 2012

Prediction Of Compressive Creep Bhaviour In Flexible Polyurethane Foam Over Long Time Scales And At Elevated Temperatures, Conor Briody, Barry Duignan, Stephen Jerrams, Stephen Ronan

Articles

Compressive creep gradually affects the structural performance of flexible polymeric foam material over extended time periods. When designing components, it is often difficult to account for long-term creep, as accurate creep data over long time periods or at high temperatures is often unavailable. This is mainly due to the lengthy testing times and/or inadequate high temperature testing facilities. This issue can be resolved by conducting a range of short-term creep tests and applying accurate prediction methods to the results. Short-term creep testing was conducted on viscoelastic polyurethane foam, a material commonly used in seating and bedding systems. Tests were conducted …

Go to article

Double Paddle Oscillators For The Mechanical Spectroscopy Of Ion-Solid Interactions, Jason Puls Dec 2012

Double Paddle Oscillators For The Mechanical Spectroscopy Of Ion-Solid Interactions, Jason Puls

All Theses

We demonstrated using a double paddle oscillator to measure subsurface defect formation at room temperatures caused by ion implantation. This sensor has a low amount of noise based because of its high quality factors in certain modes. The double paddle oscillator was bombarded with Ar ions under ultra-high vacuum conditions while it was oscillating. The resultant resonant frequency changes were discussed as a method to determine defect formation inside the bulk substrate.

Go to article

Electric Field-Induced Tetragonal To Orthorhombic Phase Transitions In [110]C-Oriented Batio₃ Single Crystals, D. J. Franzbach, Yijia Gu, Long-Qing Chen, K. G. Webber Dec 2012

Electric Field-Induced Tetragonal To Orthorhombic Phase Transitions In [110]C-Oriented Batio₃ Single Crystals, D. J. Franzbach, Yijia Gu, Long-Qing Chen, K. G. Webber

Materials Science and Engineering Faculty Research & Creative Works

Electric field-induced phase transitions in [110]c-oriented BaTiO3 single crystals were studied by macroscopic electrical measurements in the temperature range from 20 °C to 50 °C. Discontinuous, hysteretic jumps in the polarization and strain were observed, indicating a tetragonal ↔ orthorhombic phase transition. The critical electric field to induce the transition was found to shift to higher values with increasing temperature. The Landau-Devonshire theory was used to analyze the observed electric field-induced T ↔ O phase transitions.

Go to article

Pulse Sharpening Effects Of Thin Film Ferroelectric Transmission Lines, Robert J. Sleezer Dec 2012

Pulse Sharpening Effects Of Thin Film Ferroelectric Transmission Lines, Robert J. Sleezer

Graduate Theses and Dissertations

Advances in material science have resulted in the development of electrically nonlinear high dielectric thin film ferroelectrics, which have led to new opportunities for the creation of novel devices. This dissertation investigated one such device: a low voltage nonlinear transmission line (NLTL). A finite element simulation of ferroelectric transmission lines showed that NLTLs are capable of creating shockwaves. Additionally, if the losses are kept sufficiently low, it was shown that voltage gain should be possible. Furthermore, a method of accounting for material dispersion was developed. Results from simulations including material dispersion showed that temporal solitons might be possible from a …

Go to article

Titanium Aluminum Nitride Films Deposited By Ac Reactive Magnetron Sputtering: Study Of Positioning Effect In An Inverted Cylindrical Magentron Sputtering System, George C. Vandross Ii Dec 2012

Titanium Aluminum Nitride Films Deposited By Ac Reactive Magnetron Sputtering: Study Of Positioning Effect In An Inverted Cylindrical Magentron Sputtering System, George C. Vandross Ii

Graduate Theses and Dissertations

TiAlN films were deposited on glass substrates by AC magnetron sputtering at 2 kW with constant Argon and Nitrogen gas flow rates to study the effects of positioning on the deposited films. The deposition system used was an ICM-10 IsoFlux cylindrical magnetron sputtering chamber. The samples were placed in different positions and tilts with respect to the location of the Titanium and Aluminum targets in the chamber. It was found that with change in position and application of tilts, deposited films acquired different physical and chemical properties. It is believed that the differences in these properties were caused by to …

Go to article

Plasma Test On Industrial Diamond Powder In Hydrogen And Air For Fracture Strength Study, Rohit Asuri Sudharshana Asuri Sudharshana Chary Dec 2012

Plasma Test On Industrial Diamond Powder In Hydrogen And Air For Fracture Strength Study, Rohit Asuri Sudharshana Asuri Sudharshana Chary

UNLV Theses, Dissertations, Professional Papers, and Capstones

Diamonds are the most precious material all over the world. Ever since their discovery, the desire for natural diamonds has been great; recently, the demand has steeply increased, leading to scarcity. For example, in 2010, diamonds worth $50 billion were marketed. This increased demand has led to discovering alternative sources to replace diamonds. The diamond, being the hardest material on earth, could be replaced with no other material except another diamond. Thus, the industrial or synthetic diamond was invented. Because of extreme hardness is one of diamond's properties, diamonds are used in cutting operations. The fracture strength of diamond is …

Go to article

Comparison And Simulation Of Salt-Ceramic Composites For Use In High Temperature Concentrated Solar Power, Lauren Michelle Fossile Dec 2012

Comparison And Simulation Of Salt-Ceramic Composites For Use In High Temperature Concentrated Solar Power, Lauren Michelle Fossile

UNLV Theses, Dissertations, Professional Papers, and Capstones

Due to the inherently intermittent nature of solar energy caused by cloud cover among other sources, thermal storage systems are needed to make solar energy more consistent. This same technology could be used to prolong the daily number of useful hours of solar energy power plants. Salt-ceramic materials are a relatively new prospect for heat storage, but have been researched mostly with magnesium oxide and several different carbonate salts. Salt ceramics are a phase change material where the salt changes phase inside the ceramic structure allowing for the system to use the sensible heat of both materials and the latent …

Go to article

Recrystallization Kinetics Of 3c Silicon Carbide Implanted With 400 Kev Cesium Ions, Daniel Denell Osterberg Dec 2012

Recrystallization Kinetics Of 3c Silicon Carbide Implanted With 400 Kev Cesium Ions, Daniel Denell Osterberg

Boise State University Theses and Dissertations

Polycrystalline 3C silicon carbide was implanted at room temperature with 400 keV cesium ions to a dose of 1016 ions·cm-2. The samples were then annealed at 600 – 1000°C for 0-48 hours in ultra-high purity argon. The implanted zone of each sample was characterized by transmission electron microscopy and secondary ion mass spectroscopy. It is shown that the implantation resulted in a 217 ± 2 nm amorphous region with microstructural damage extending to approximately 250 nm below the surface. Recrystallization of the amorphous region was observed at 725°C, although minimal densification was observed until ≥ 800°C. Densification …

Go to article

Fabrication Of Solid Solution Tungsten-Rhenium Alloys By High Energy Ball Milling And Spark Plasma Sintering, Cory C. Sparks Dec 2012

Fabrication Of Solid Solution Tungsten-Rhenium Alloys By High Energy Ball Milling And Spark Plasma Sintering, Cory C. Sparks

Boise State University Theses and Dissertations

Tungsten-rhenium powders of varying compositions were fabricated by spark plasma sintering (SPS). In initial exploration of the parameter space, W-25 at% Re powders were blended and consolidated by SPS at 1500 to 1900°C with sintering dwell times of 0 to 60 minutes. In addition, the influence of milling was investigated. W-25 at% Re powders were high-energy ball milled at 200 to 400 rpm for 5 hours and consolidated at 1700°C with sintering dwell times of 0 to 60 minutes. The sample densities, grain sizes, porosities, contamination level, and hardness values were measured. The intermetallic content, specifically the fraction of σ-phase, …

Go to article

Polymeric Eutectic Drug Delivery System, S. Tuntarawongsa, T. Phaechamud Dec 2012

Polymeric Eutectic Drug Delivery System, S. Tuntarawongsa, T. Phaechamud

Journal of Metals, Materials and Minerals

Eutectic system is the mixture of at least two substances that suppresses melting point for each of them. The viscosity enhancement of liquid eutectic by polymer addition might increase the viscous environment for retardation of drug release. Typically, there are rare polymers that can dissolve in the liquid eutectic. The aim of this study was to develop the polymeric eutectic delivery system for controlling the drug delivery. Liquid eutectic used as vehicle was prepared by mixing menthol and camphor in various ratios. The obtained lowest viscosity liquid eutectic was used as vehicle in this study. Various polymers were attempted to …

Go to article

Implementation And Validation Of Fault-Rupture Response Spectrum Analysis Procedure In Csibridge For Bridges Crossing Earthquake Fault Ruptures, Jennifer Evelyn Tures Dec 2012

Implementation And Validation Of Fault-Rupture Response Spectrum Analysis Procedure In Csibridge For Bridges Crossing Earthquake Fault Ruptures, Jennifer Evelyn Tures

Master's Theses

This thesis evaluates the application of a simplified analysis procedure as implemented in version 16 of CSiBridgeTM for design of bridges crossing earthquake fault ruptures. The fault-rupture response spectrum analysis (FR-RSA) approximation method has been proved adequate for both straight and curved ordinary bridges, but lacked a comfortable interface to accommodate the method users. Computers and Structure, Inc. has implemented the FR-RSA procedure into CSiBridgeTM, a user-friendly integrated 3-D bridge design software, as an added seismic design feature. By combining the response of the bridge due to the quasi-static displacement from the fault strike-slip rupture and the …

Go to article

First Prev Next Last