Engineering Commons^™

Dysprosium Transport In Nd-Fe-B Pellets, Parawee Pumwongpitak

Dissertations, Master's Theses and Master's Reports - Open

The addition of heavy rare earth (RE) elements to Nd2Fe14B based magnets to form (Nd,Dy)₂Fe₁₄B is known to increase the coercivity and high temperature performance required for hybrid vehicle electric motors and other extreme temperature applications. Attempts to conserve heavy rare earth elements for high temperature (RE)₂Fe₁₄B based magnets have led to the development of a grain boundary diffusion process for bulk magnets. This process relies on transport of a heavy rare earth, such as Dy, into a bulk Nd₂Fe₁₄B magnet along pores, a low volume fraction of …

Parametric Study Of Reaxff Simulation Parameters For Molecular Dynamics Modeling Of Reactive Carbon Gases, Benjamin David Jensen

Dissertations, Master's Theses and Master's Reports - Open

Abstract

Intergranular Corrosion And Stress Corrosion Cracking Of Extruded Aa6005a, David James Seguin

Dissertations, Master's Theses and Master's Reports - Open

A research program focused on understanding the intergranular corrosion (IGC) and stress corrosion cracking (SCC) behavior of AA6005A aluminum extrusions is presented in this dissertation. The relationship between IGC and SCC susceptibility and the mechanisms of SCC in AA6005A extrusions were studied by examining two primary hypotheses.

IGC susceptibility of the elongated grain structure in AA6005A exposed to low pH saltwater was found to depend primarily on the morphology of Cu-containing precipitates adjacent to the grain boundaries in the elongated grain structure. IGC susceptibility was observed when a continuous (or semi-continuous) film of Cu-containing phase was present along the grain …

Accurate Prediction Of Spectral Phonon Relaxation Time And Thermal Conductivity Of Intrinsic And Perturbed Materials, Tianli Feng

Open Access Theses

The prediction of spectral phonon relaxation time, mean-free-path, and thermal conductivity can provide significant insights into the thermal conductivity of bulk and nanomaterials, which are important for thermal management and thermoelectric applications. We perform frequency-domain normal mode analysis (NMA) on pure bulk argon and pure bulk germanium. Spectral phonon properties, including the phonon dispersion, relaxation time, mean free path, and thermal conductivity of argon and germanium at different temperatures have been calculated. We find the dependence of phonon relaxation time τ on frequency ω and temperature T vary from ~ω^-1.3 to ~ω^-1.8 and ~T^-0.8 to ~T^{-1.8 …}

High Speed Turning Of Compacted Graphite Iron (Cgi) Using Controlled Modulation, Tyler Paul Stalbaum

Open Access Theses

Compacted graphite iron (CGI) is a material which emerged as a candidate material to replace cast iron (CI) in the automotive industry for engine block castings. Its thermal and mechanical properties allow the CGI-based engines to operate at higher cylinder pressures and temperatures than CI-based engines, allowing for lower fuel emissions and increased fuel economy. However, these same properties together with the thermomechanical wear mode in the CGI-CBN system result in poor machinability and inhibit CGI from seeing wide spread use in the automotive industry.

In industry, machining of CGI is done only at low speeds, less than V = …

Applications Of High Throughput (Combinatorial) Methodologies To Electronic, Magnetic, Optical, And Energy-Related Materials, Martin L. Green, Ichiro Takeuchi, Jason R. Hattrick-Simpers

Faculty Publications

High throughput (combinatorial) materials science methodology is a relatively new research paradigm that offers the promise of rapid and efficient materials screening, optimization, and discovery. The paradigm started in the pharmaceutical industry but was rapidly adopted to accelerate materials research in a wide variety of areas. High throughput experiments are characterized by synthesis of a “library” sample that contains the materials variation of interest (typically composition), and rapid and localized measurement schemes that result in massive data sets. Because the data are collected at the same time on the same “library” sample, they can be highly uniform with respect to …

A Laboratory Experiment Using Nanoindentation To Demonstrate The Indentation Size Effect, Wendelin Wright, Gang Feng, William D. Nix

Faculty Journal Articles

A laboratory experiment using nanoindentation to demonstrate the indentation size effect is described. This laboratory introduces students to sophisticated instrumentation at low cost and low risk and utilizes recent research in the materials community as its foundation. The motivation, learning objectives, experimental details, data, and data analysis are presented. This experiment is intended for use in an upper-division materials science elective at the university level and has been successfully used in laboratory courses for senior undergraduates and first-year graduate students at Stanford University and Santa Clara University.

Preparation, Characterization And Catalytic Activity Study Of Transition Metal Doped Porous Γ-Alumina, Seham Nasser Al Hadrami

Theses

Transition-metal ions -doped γ-alumina composites with various dopant concentrations (Cr³⁺, Fe³⁺, Ce³⁺, Zn²⁺, Mn²⁺, V²⁺ and Cu²⁺) were prepared by straightforward tempIate-free sol-gel method. They were characterized by XRD, FTIR, SEM, NMR and N₂ adsorption-desorption isotherm technique. The presence of dopant metal ions, generally, enhanced the gel formation and their behavior was dependent on the nature of the metal ion and its concentration. Certain ions, especially Fe³⁺, resulted in rapid formation of a transparent gel upon hydro lysis. The presence of the acetylacetonate …

The Processing Of Aluminum Gasarites Via Thermal Decomposition Of Interstitial Hydrides, Joseph James Licavoli

Dissertations, Master's Theses and Master's Reports - Open

Gasarite structures are a unique type of metallic foam containing tubular pores. The original methods for their production limited them to laboratory study despite appealing foam properties. Thermal decomposition processing of gasarites holds the potential to increase the application of gasarite foams in engineering design by removing several barriers to their industrial scale production. The following study characterized thermal decomposition gasarite processing both experimentally and theoretically. It was found that significant variation was inherent to this process therefore several modifications were necessary to produce gasarites using this method. Conventional means to increase porosity and enhance pore morphology were studied. Pore …

Characterization Of And Controlling Morphology Of Ultra-Thin Nanocomposites, Guy C. Laine

Theses and Dissertations--Chemical and Materials Engineering

Ultrathin film nanocomposites are becoming increasingly important for specialized performance of commercial coatings. Critical challenges for ultrathin film nanocomposites include their synthesis and characterization as well as their performance properties, including surface roughness, optical properties (haze, refractive index as examples), and mechanical properties. The objective of this work is to control the surface roughness of ultrathin film nanocomposites by changing the average particle size and the particle volume fraction (loading) of monomodal particle size distributions. This work evaluated one-layer and two-layer films for their surface properties. Monodispersed colloidal silica nanoparticles were incorporated into an acrylate-based monomer system as the model …

Influence Of Surface Modification On Properties And Applications Of Complex Engineered Nanoparticles, Binghui Wang

Theses and Dissertations--Chemical and Materials Engineering

Complex engineered nanoparticles (CENPs) are being used on various applications. Their properties are different from those of neat nanoparticles. The dissertation explores these differences from four aspects: 1) Modify carbon nanomaterials’ inert surfaces and investigate the effect on thermal and rheological behavior of their dispersions; 2) Generate self-assembly bi-layer structure of oxide nanoparticles via surface modification; 3) Study interaction between lysozyme and different surface-charged ceria nanoparticles; 4) Investigate the biodistribution and transformations of CENPs in biological media.

An environment-friendly surface modification was developed to modify surfaces of carbon nanomaterials for increasing their affinity to non-polar fluid. It can offset formation …

Structural Tailoring Of Nanoporous Metals And Study Of Their Mechanical Behavior, Lei Wang

Theses and Dissertations--Chemical and Materials Engineering

Nanoporous (np) metals and alloys are the subject of increasing research attention due to their high surface-area-to-volume ratio. Numerous methods exist to create np metals, with dealloying being a common approach. By dissolving one or more elements from certain alloy systems, porous structure can be generated. Utilizing this method, multiple np metals, including np-Ni, np-Ir, and np-Au were created. By carefully adjusting precursor type and dealloying conditions for each system, nanoporous Ni/Ir/Au with different morphologies and even controllable ligament/pore size were achieved.

The mechanical behavior of porous materials is related to their fully dense counterparts by scaling equations. Established scaling …

Electromechanical Interaction On The Deformation Behavior Of Metallic Materials, Guangfeng Zhao

Theses and Dissertations--Chemical and Materials Engineering

Metallic materials play important roles in providing electrical, thermal, and mechanical functions in electronic devices and systems. The understanding of the electrical-thermal-mechanical interaction caused by the passage of electric current with high density is important to improve the performance and reliability of electronic assembly and packaging. The electromechanical interaction on the deformation behavior of copper and tin is studied in this work.

The electromechanical response of Cu strips was studied by passing a DC electric current. The electric resistance linearly increased with time before the occurrence of electric fusing. The electrothermal interaction led to the buckling of the Cu strips …

Infiltrated Composite Electrodes For Solid Oxide Fuel Cells, Aligul Buyukaksoy

Doctoral Dissertations

"Solid oxide fuel cells (SOFCs) are electrochemical devices which can convert chemical energy to electrical energy with efficiencies up to 60%. In order for SOFCs to be favorable energy conversion devices, the power obtained from a unit volume should be improved. This corresponds to minimized resistances from SOFC components (composite electrodes and electrolyte). Stability of the generated power is another important issue. Degradation of SOFCs with time due to microstructural processes or chemical reactions that occur at operating conditions; and due to reduction/oxidation cycles caused by the changes in the anode has been an important obstacle that has prevented the …

On The Effect Of Silicon And Phosphorus During The Precipitation Of Κ-Carbide In Fe-Mn-Al-C Alloys, Laura Bartlett

Doctoral Dissertations

"Implementation of lightweight high manganese and aluminum steels for use in high energy absorbing applications requires a detailed knowledge of how alloying additions and impurities affect age hardening and high strain rate fracture properties. Dynamic fracture toughness is an important design criterion but has not been reported previously in these alloys. In addition, previous studies have shown that silicon and phosphorus increased the strength and aged hardness; however, the mechanism was unknown. This research mainly focuses on the effect of silicon and phosphorus on the precipitation of Κ-carbide and alloy partitioning during aging. Short range ordering, SRO, of Fe-Al-C into …

Structural, Optical And Electrical Properties Of Yttrium-Doped Hafnium Oxide Nanocrystalline Thin Films, Abhilash Kongu

Open Access Theses & Dissertations

Hafnium oxide (HfO2) has emerged as the most promising high-k dielectric for Metal-Oxide-Semiconductor (MOS) devices and has been highlighted as the most suitable dielectric materials to replace silicon oxide because of its comprehensive performance. In the present research, yttrium-doped HfO2 (YDH) thin films were fabricated using RF magnetron sputter deposition onto Si (100) and quartz with a variable thickness. Cross-sectional scanning electron microscopy coupled with Filmetrics revealed that film thickness values range from 700 A° to 7500 A°. Electrical properties such as AC Resistivity and current-voltage (I-V) characteristics of YDH films were studied. YDH films that were relatively thin (<1500 A°) crystallized in monoclinic phase while thicker films crystallized in cubic phase. The band gap (Eg) of the films was calculated from the optical measurements. The band gap was found to be ∼5.60 eV for monoclinic while it is ∼6.05 eV for cubic phase of YDH films. Frequency dependence of the electrical resistivity (ρac) and the total conductivity of the films were measured. Resistivity decreased (by three orders of magnitude) with increasing frequency from 100 Hz to 1 MHz, attributed due to the hopping mechanism in YDH films. Whereas, while ρac∼1Ω-m at low frequencies (100 Hz), it decreased to ∼ 104 Ω-cm at higher frequencies (1 MHz). Aluminum (Al) metal electrodes were deposited to fabricate a thin film capacitor with YDH layer as dielectric film thereby employing Al-YDH-Si capacitor structure. The results indicate that the capacitance of the films decrease with increasing film thickness. A detailed analysis of the electrical characteristics of YDH films is presented.

Experimental Study On The Fabrication Of Advanced Materials For Energy Applications Using High Energy Mechanical Milling, Ashvin Kumar Narayana Swamy

Open Access Theses & Dissertations

The reaction of aluminum (Al) powder with water has the potential for on demand hydrogen generation. Conventional Al powders, however, react with water slowly due to a highly protective oxide layer on the particle surface. Current methods for Al activation involve harmful and expensive materials. The nano-scale Al powders also remain very expensive and have problems such as a large amount of oxide on the surface. The use of aluminum in an energy generation cycle is also hindered by the fact that, although Al is the most abundant metal in the Earth's crust, its recovery from ore consumes a lot …

Comparative Characterization Of Ni-Base Superalloys Fabricated By Laser And Electron Beam Melting Technologies, Krista Amato

Open Access Theses & Dissertations

Nickel-base superalloys have been used in cast and wrought, and powder metallurgy forms for nearly four decades for industrial and automotive applications. One drawback of cast alloys is that upon solidification, there is minimal microstructural control. Another issue to be improved is to eliminate the limitations of shapes and forms of fabricated alloys.

Rapid prototyping is a new technology of additive manufacturing that shows to be promising for the freeform fabrication of novel superalloys, including nickel-base alloys. New rapid manufacturing technologies allow us to produce parts in any shape that can be designed by computer-aided design (CAD) software. Additionally, the …

Rbd2po4: Room Temprature Synthesis, Chemical And Structural Stablity Upon Heating, Masoud Mollaee

Open Access Theses & Dissertations

Monoclinic RbD2PO4 polycrystals were synthesized via the room temperature crystallization of RbH2PO4 dissolved in D2O. Powder x-ray diffraction (XRD) data collected at T=25 ºC indicate that this deuterated compound crystallizes in space group P21/m with unit cell parameters a=7.688í?, b=6.192í?, c=4.781í? and β=109.02°, and is isomorphic with the intermediate-temperature phase of its hydrogenated counterpart rubidium dihydrogen phosphate (RDP). We found no evidence of previously reported [Phase Transitions 80, 17 (2007)] polymorphic phase transition in rubidium dideuterium phosphate (DRDP) upon heating from room temperature to 210 ºC. All lattice parameters vary smoothly within this temperature range, demonstrating that the P21/m phase …

Structure And Electronic Properties Of Pure And Nitrogen Doped Nanocrystalline Tungsten Oxide Thin Films, Vemnkata Rama Sesha Ravi Kumar Vemuri

Open Access Theses & Dissertations

Tungsten oxide (WO₃) is a multifunctional material which has applications in electronics, sensors, optoelectronics, and energy-related technologies. Recently, electronic structure modification of WO₃ to design novel photocatalysts has garnered significant attention. However, a fundamental understanding of nitrogen induced changes in the structure, morphology, surface/interface chemistry, and electronic properties of WO₃ is a prerequisite to producing materials with the desired functionality and performance. Also, understanding the effect of thermodynamic and processing variables is highly desirable in order to derive the structure-property relationships in the W-O/W-O-N material system. The present work was, therefore, focused on studying the effects …

Effect Of Hafnium-Incorporation On The Microstructure And Dielectric Properties Of Cobalt Ferrite Ceramics, Stephen Josiah Wells

Open Access Theses & Dissertations

The effect of hafnium ion (Hf⁴⁺) incorporation in cobalt ferrite (CFO) was studied. Samples of Hf substituted CFO ceramic (CoFe_2-xHf_xO₄), were synthesized in the laboratory with hafnium concentrations ranging from x=0.000 to x=0.200. X-ray diffraction scans show that the Hafnium CFO crystalizes in the inverse spinel phase. Inclusion of hafnium causes lattice expansion, increasing the lattice parameter from 8.374 í? for pure CoFe2O4 to 8.391 í? for the highest concentration of hafnium tested (x=0.020). The dielectric properties of CFO are greatly enhanced by inclusion of hafnium. The enhancement is due to the …

Thermal Barrier Coatings (Tbc's) For High Heat Flux Thrust Chambers, Christopher Michael Bradley

Open Access Theses & Dissertations

The last 30 years materials engineers have been under continual pressure to develop materials with a greater temperature potential or to produce configurations that can be effectively cooled or otherwise protected at elevated temperature conditions. Turbines and thrust chambers produce some of the harshest service conditions for materials which lead to the challenges engineers face in order to increase the efficiencies of current technologies due to the energy crisis that the world is facing. The key tasks for the future of gas turbines are to increase overall efficiencies to meet energy demands of a growing world population and reduce the …

Microstructure And Properties For Titanium Aluminide Superalloy Prototypes Fabricated By Electron Beam Melting And Thermally Processed, Jennifer Hernandez

Open Access Theses & Dissertations

Gamma TiAl has been considered to be an ideal replacement for Ni-base superalloy aerospace applications, particularly in weight-critical applications. While bulk, fully dense gamma-TiAl is 50% less dense than Ni-base superalloys, it also has excellent mechanical properties at high temperature (up to ~800°C). Pre alloyed (Ti-48Al-2Cr-2Nb) powder was used to fabricate solid, fully dense (3.85 g/cm3) components and foam components with densities ranging from 0.33 g/cm³ to 0.46 g/cm³ by electron beam melting (EBM). A 10:1 blend of 2-phase TiAl (Ti-48Al-2Cr-2Nb in ^a/_o) : Inconel 625 (Ni-22Cr-6Mo-2Nb in ^a/_o) pre-alloyed powders produced …

New Topics On Nanoindentation Of Polymers And Composite Materials, Ricardo Martinez-Hernandez

Open Access Theses & Dissertations

In this study, nanoindentation was used to determine Young's modulus of homogeneous plastic materials as well as inhomogeneous epoxy woven fabric composites using various indenters. In the first part, homogeneous PMMA and polycarbonate were characterized using conical and spherical indenters. The conventional approach of the inverse analysis was modified in order to account for effects obtained during spherical nanoindentation. The experimental results were verified using FEA analysis in ABAQUS. It was found that viscous effects were present in conical nanoindentations which led to an overestimation of contact stiffness. The second part, the response of carbon and glass fiber woven fabric …

Reducing Metal Alloy Powder Costs For Use In Powder Bed Fusion Additive Manufacturing: Improving The Economics For Production, Fransisco Medina

Open Access Theses & Dissertations

Titanium and its associated alloys have been used in industry for over 50 years and have become more popular in the recent decades. Titanium has been most successful in areas where the high strength to weight ratio provides an advantage over aluminum and steels. Other advantages of titanium include biocompatibility and corrosion resistance. Electron Beam Melting (EBM) is an additive manufacturing (AM) technology that has been successfully applied in the manufacturing of titanium components for the aerospace and medical industry with equivalent or better mechanical properties as parts fabricated via more traditional casting and machining methods. As the demand for …

Process Study And Control Of Electron Beam Melting Technology Using Infrared Thermography, Jorge Mireles

Open Access Theses & Dissertations

An IR camera was installed in an Arcam A2 system (Arcam AB, Mölndal, Sweeden) and layer-by-layer image acquisition was achieved. The camera's capability to detect manufacturing defects was evaluated by implementing computer vision techniques using LabVIEW measurement and programming software (National Instruments, Austin, TX). Thermal maps acquired by the IR camera allowed layer-by-layer part temperature to be recorded. A core objective of this research was to study the impact of processing temperature on EBM-fabricated Ti-6Al-4V parts and achieve controlled mechanical properties. In this research, build variations were achieved by modifying parameters that change processing temperature from the standard processing temperature. …

Crystal Structure, Phase, And Optical Properties Of Yttrium-Doped Hafnium Oxide Nanocrystalline Thin Films, Alejandro Ortega

Open Access Theses & Dissertations

Yttrium-doped hafnium oxide (YDH) nanocrystalline films were produced by sputter-deposition at various substrate times and temperatures, to produce YDH films in a wide range of thicknesses, dYDH∼25 to 1100 nm. The deposition was made onto optical grade quartz and sapphire substrates. Samples deposited on sapphire were subject to post-deposition annealing (PDA) at various times (3-24 hr) and temperatures (1100 - 1500 °C). The effect of d[special characters omitted]YDH on the crystal structure, surface/interface morphology and optical properties of YDH films was investigated. X-ray diffraction analyses revealed the formation of monoclinic phase for relatively thin films (<150nm). The evolution towards stabilized cubic phase with increasing dYDH [special characters omitted]is observed. The scanning electron microscopy results indicate the dense, columnar structure of YDH films as a function of dYDH. Spectrophotometry analyses indicate that the grown YDH films are transparent and exhibit interference fringes. The band gap was found to be ∼ 5.60 eV for monoclinic YDH films while distinct separation and an increase in band gap to 6.03 eV is evident with increasing dYDH and formation cubic YDH films. The PDA films band gaps were found to be between 5.31 and 5.72 eV, all of which exhibit secondary gaps. A correlation between growth conditions, annealing, phase evolution, and optical properties of the YDH nanocrystalline thin films is established.

Recent Developments In Magneto-Optic Garnet-Type Thin-Film Materials Synthesis, Mohammad Nur E Alam, Mikhail Vasiliev, Viacheslav Kotov, Kamal Alameh

Research outputs 2013

Magneto-optic (MO) garnets are used in a range of applications in nanophotonics, integrated optics, communications and imaging. Bi-substituted iron garnets of different compositions are the most useful class of materials in applied magneto- optics due to their excellent MO properties (large Faraday effect) and record-high MO figure of merit among all semi- transparent dielectrics. It is highly desirable to synthesise garnets which possess simultaneously a high MO figure of merit and large uniaxial magnetic anisotropy. However, the simultaneous optimization of several material properties and parameters can be difficult in single-layer garnet thin films, and it is also challenging to prepare …

Non-Equilibrium Melting And Sublimation Of Graphene Simulated With Two Interatomic Potentials, Brad Steele

USF Tampa Graduate Theses and Dissertations

The mechanisms of the sublimation of graphene at zero pressure and the condensation of carbon vapor is investigated by molecular dynamics (MD) simulations. The interatomic interactions are described by the Reactive Empirical Bond Order potential (REBO). It is found that graphene sublimates at a temperature of 5,200 K. At the onset of sublimation, defects that contain several pentagons and heptagons are formed, that are shown to evolve from double vacancies and stone wales defects. These defects consisting of pentagons and heptagons act as nucleation sites for the gaseous phase. The influence of the interatomic interactions on the sublimation process are …

Rapid Repair Of Severely Damaged Rc Columns With Different Damage Conditions: An Experimental Study, Ruili He, Lesley Sneed, Abdeldjelil Belarbi

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

No abstract provided.