Engineering Commons^™

A Study Of Small Watersheds Within The State Of Missouri, Terence E. Harbaugh

Masters Theses

"The present status of data from watersheds in the under 10 square mile drainage area classification, pages much to be desired. However, this study of 45 small watersheds within the State of Missouri gives an indication that surface runoff from these basins may be predicted with a fair degree of accuracy. The inclusion of a shape factor AL² and its use as a portion of the "basin index" (AL²S^1/2) gives accurate results as a predictor of the "mean annual flood". The mean annual flood may be adequately computed by the formula, MAF = 113(AL^{2 …}

Shear Stress Distribution In Haunched Beam Models, Manyu K. Mehta

Masters Theses

"The purpose of this thesis has been to give the distribution of shear stress inside a haunch. A haunch is generally provided to relieve high stress concentrations at the face of the column. However the nature of shear stress distribution inside the haunch is not known.

This stress distribution was determined from a photo- elastic study on a CR-39 model. It is noted that the haunch reduces the stress concentration at the face of the column but at the same time somewhere near the point where the haunch meets the beam there is a high stress concentration.

Shear stress changes …

Velocity Distribution Induced By Free Jet Impact On A Stilling Basin, Sedat Özkol

Masters Theses

"At present, the use of the free jet impacting on a stilling basin as an energy dissipator is not very common, as there is very little information available concerning this particular field. However, if conditions are favorable, this type of energy dissipator will be quite economical to construct.

In this paper it was found that the hydraulic behavior of the free jet impacting on a stilling basin can be determined to a degree which may be considered accurate for practical purposes. It was also shown that given the free jet velocity, the magnitudes of the velocities at the critical points …

Analysis Of Flat Plates By Reaction Distribution Method, David D. W. Yang

Masters Theses

"This study was made to analyze rectangular flat plates by the method of Reaction Distribution and to compare results obtained by this method with that of other methods. The basic approach is to divide the plate into an equivalent grid system and introduce temporary supports at the intersecting joints. The results from this study shows that the Reaction Distribution method is useful in a qualitative analysis of the behavior in a plate but is less satisfactory in obtaining reliable quantitative results"--Abstract, page 2.

A Study Of Composite Beams Made To Find An Approximate Relationship Between The Top And Bottom Flange Steel Ratio, Murli U. Hasrajani

Masters Theses

"At present in building construction the use of the composite beams is not very common. The use of the concrete beams is seen in almost all construction. By using composite beams in building construction more durability and savings in cost could be achieved. This paper shows an approximate design procedure which could be followed without running a number of trials with different sections to arrive at the required one. The ratio of top flange steel to the bottom flange steel can be determined if one knows the loads, span and the depth of the beam required"--Abstract, page i.

A Comparison Of Backwater Profile Computation, Alwin Chang Hsin Young

Masters Theses

"Bakhmeteff's, Von Seggern's, and the Standard Step methods were chosen for a comparative study of backwater profile determinations made with the assistance of a digital computer. This study concentrated on the M-l type of curves for different kind of prismatic channels; i.e. rectangular, trapezoidal, and parabolic channels. From the results obtained by each method for different channels, the consistency between the several methods and their applicability to all shapes of channel had been studied. Also the effect of the number of reaches used in flow profile determinations, the effect of the use of an average value of (1-ß), hydraulic exponents …

Significance Of Layer Deflection Measurements : Technical Report, Richard David Walker, Eldon J. Yoder, Robert Lowry, Walter T. Spencer

JTRP Technical Reports

No abstract provided.

Urban Intersection Evaluation Utilizing Average Delay Per Vehicle : Technical Report, William Walter Schenler, Harold L. Michael

JTRP Technical Reports

No abstract provided.

Serviceability Ratings Of Highway Pavements, Velma Fumiko Nakamura

JTRP Technical Reports

No abstract provided.

Nuclear Moisture-Density Measurements In Construction Control : Technical Paper, Alfonso Burgers, Eldon J. Yoder

JTRP Technical Reports

No abstract provided.

Analysis Of Road Roughness Of Flexible Pavements Using The Kentucky Accelerometer, Lyle G. Wermers

JTRP Technical Reports

No abstract provided.

Serviceability Ratings Of Highway Pavements : Technical Paper, Velma Fumiko Nakamura, Harold L. Michael

JTRP Technical Reports

No abstract provided.

Flexible Pavement Deflections-Methods Of Analysis And Interpretation : Technical Paper, Eldon J. Yoder

JTRP Technical Reports

No abstract provided.

A Laboratory Study Of The Degradation Of Aggregates In Bituminous Mixes, Fred Moavenzadeh

JTRP Technical Reports

No abstract provided.

Recent Developments In Aggregate Research, John Francis Mclaughlin

JTRP Technical Reports

No abstract provided.

A Study Of School Crossing Protection : Technical Paper, Forrest D. Miller, Harold L. Michael

JTRP Technical Reports

No abstract provided.

Physical Characteristics Of Sand-Soil Mixtures Under Repeated Dynamic Loads, Rodney Wendell Johnson

JTRP Technical Reports

No abstract provided.

Variability Of Engineering Properties Of Brookston And Crosby Soils, Delon Hampton, Eldon J. Yoder, I. W. Burr

JTRP Technical Reports

No abstract provided.

Evaluation Of Asphalt-Aggregate Distribution In Bituminous Mixes By Autoradiography , Donald R. Lamb

JTRP Technical Reports

No abstract provided.

Procedural Manual For A School Crossing Protection Program In The Communities Of Indiana, Harold L. Michael

JTRP Technical Reports

No abstract provided.

Measurement Of Moisture Gradients In Concrete Pavement Slabs : Progress Report No. 4, J. Richard Bell

JTRP Technical Reports

No abstract provided.

A Sufficiency Rating Method For Urban Intersections : Technical Paper, William Walter Schenler, Harold L. Michael

JTRP Technical Reports

No abstract provided.

A Quantitative Evaluation Of The Geometric Aspects Of Highways, Kenneth John Tharp

JTRP Technical Reports

No abstract provided.

The Simulation Of Traffic Flow To Obtain Volume Warrants For Intersection Control, Russell Maclean Lewis

JTRP Technical Reports

No abstract provided.

Repeated Load Triaxial Test With Pore Pressure Measurement : Technical Paper, Rodney Wendell Johnson, Eldon J. Yoder

JTRP Technical Reports

No abstract provided.

The Irish Plumber And Heating Contractor, January 1962 (Complete Issue)

Building Services Engineering

No abstract provided.

A Machine-Laid Surmountable Bituminous Concrete Median, Robert L. Florence

Kentucky Transportation Center Research Report

On August 28, 1961, personnel of the Research Division were requested to observe a demonstration of a newly developed Etnyre Median Paver. The demonstration was given at the Lehman-Roberts Company plant in Lexington, and was arranged primarily for the benefit of the paving contractor working on Euclid Avenue in Lexington. The paving contract called for the construction of a surmountable bituminous concrete median which, to our understanding, is the first instance for construction of that type to be machine-laid. Some doubts arose during the demonstration as to the ability of the machine to hold alignment and to give adequate compaction. …

The Irish Plumber And Heating Contractor, December 1961 (Complete Issue)

Building Services Engineering

No abstract provided.

An Investigation Of Indeterminate Structures Stressed Beyond The Proportional Limit, Jack B. Joyce

Civil Engineering ETDs

In the structural field the methods of designing have been geared to the development of materials...In a more current appraisal we see steel and concrete being updated still further. Pre-stressed concrete is a common sight in present day construction work and, to a lesser extent, the educated eye sees rigid frames designed to ultimate load criteria. Here again are cases where materials are studied and found to possess characteristics that are adaptable to advance methods. The key to all such improvements is still the realization and utilization of material properties.

The Irish Plumber And Heating Contractor, November 1961 (Complete Issue)

Building Services Engineering

No abstract provided.