Engineering Commons^™

The Creation, Analysis, And Verification Of A Comprehensive Model Of A Micro Ion Thruster, Maxwell J. Bodnar

Master's Theses

A computational model of the micro-ion thruster MiXI has been developed, analyzed, and partially verified. This model includes submodels that govern the physical, magnetic, electrostatic, plasma physics, and power deposition of the thruster. Over the past few years, theses have been conducted with the goal of running tests and analyzing the results; this model is used to understand how the thruster components interact so as to make predictions about, and allow for optimization of, the thruster operation. Testing is then performed on the thruster and the results are compared to the output of the code. The magnetic structure of the …

Validation Of A Cfd Approach For Gas Turbine Internal Cooling Passage Heat Transfer Prediction, Daniel G. Wilde

Master's Theses

This report describes the development and application of a validated Computational Fluid Dynamics (CFD) modelling approach for internal cooling passages in rotating turbomachinery. A CFD Modelling approach and accompanying assumptions are tuned and validated against academically available experimental results for various serpentine passages. Criteria of the CFD modelling approach selected for investigation into advanced internal cooling flows include accuracy, robustness, industry familiarity, and computational cost.

Experimental data from NASA HOST (HOt Section Technology), Texas A&M, and University of Manchester tests are compared to RANS CFD results generated using Fluent v14.5 in order to benchmark a CFD modelling approach.

Capability of …

Wind Oscillator For Power Genration, Rs Vewen Ramasamy

Masters Theses

This thesis describes in detail the design, mechanical, electrical and software considerations in developing a working model for the non-conventional wind power converter called Wind Oscillator. This was based on the concept developed and patented by Tianshu Liu in the paper “Wind Oscillator and Rotor for Power Generation”[1]. In order to verify the practicality of this idea, a working model of the Wind Oscillator was designed, built and tested in the Western Michigan University wind tunnel facility. LabVIEW data acquisition and photogrammetry was performed on the model so as to evaluate the power generated by the Wind Oscillator and to …

Electric Commuter Multicopter, Marley Hunter Miller, Blake Sperry, Ike Sheppard, Olliver Fredrick Kunz, Sam Juday, Alex O'Hearn, Kyle Seth Kruse, Arthur Norwood, Jarrell Washington

Mechanical Engineering

This document describes the design, analysis, and overall goals of the Electric Commuter Multicopter (ECM) Senior Project. It was presented by Bob Addis and Bill Burner to the senior mechanical engineering class of 2015 at Cal Poly, San Luis Obispo. The progress and development of the project are described in detail and to an extent that an individual or group with similar aspirations can construct their own multicopter or expand upon this one. The goal of this project is to create an Ultralight, as defined by FAA Part 103, commuter multicopter vehicle capable of transporting an individual to and from …

Design Of Synthetic Jet Actuator For Flight Control Of Small Uav, Priyanka Pagadala

Doctoral Dissertations and Master's Theses

The main idea of this project is to develop a prototype SJA - Synthetic Jet Actuator to embed into a small UAV with modified Glauert wing cross-section for Active Flow Control. Apart from lift enhancement, drag reduction, or separation control, etc; LCO suppression might be possible by modifying the boundary layer through the use of these actuators. For initial investigation, a wing section with span of 12.4 cm and chord of 14 cm was fabricated and tests were conducted in the subsonic wind tunnel at the free stream velocities of 5 and 10 m / s. From these experiments, lift …

Sensor Fusion And Obstacle Avoidance For An Unmanned Ground Vehicle, Gurasis Singh

Doctoral Dissertations and Master's Theses

In recent years, the capabilities and potential value of unmanned autonomous systems (UAS) to perform an extensive variety of missions have significantly increased. It is well comprehended that there are various challenges associated with the realization of autonomous operations in complex urban environments. These difficulties include the requirement for precision guidance and control in conceivably GPS-denied conditions as well as the need to sense and avoid stationary and moving obstructions within the scene. The small size of some of these vehicles restricts the size, weight and power consumption of the sensor payload and onboard computational processing that can accommodated by …

Hybrid Rocket Motor Scaling Process, Joseph B. R. Vanherweg

Master's Theses

Hybrid rocket propulsion technology shows promise for the next generation of sounding rockets and small launch vehicles. This paper seeks to provide details on the process of developing hybrid propulsion systems to the academic and amateur rocket communities to assist in future research and development. Scaling hybrid rocket motors for use in sounding rockets has been a challenge due to the inadequacies in traditional boundary layer analysis. Similarity scaling is an amendment to traditional boundary layer analysis which is helpful in removing some of the past scaling challenges. Maintaining geometric similarity, oxidizer and fuel similarity and mass flow rate to …

Sense And Avoid Uas Project Final Design Report, Katie Peticolas, Cesia Cazares, Trevor Elsbree, Courtney Smith, Herberth Elie Navas

Biomedical Engineering

No abstract provided.

A Study Of Mixing In A Magnetohydrodynamic (Mhd) Microfluidic Cell By Numerical Simulations, Fangping Yuan, Kakkattukuzhy M. Isaac

Collaborative Research: Actively Controllable Microfluidics with Film-Confined Redox-Magnetohydrodynamics -- Video and Data

No abstract provided.

Flexsar A High-Quality, Flexible, Cost-Effective, Prototype Sar System, Mark Jensen, Chad Knight

Space Dynamics Laboratory Publications

The FlexSAR radar system was designed to be a high quality, low-cost, flexible prototype instrument. Many radar researchers and practitioners desire the ability to efficiently prototype novel configurations. The resulting cost and time required to modify existing radar systems is a challenging hurdle that can be prohibitive. The FlexSAR system couples an RF design that leverages connectorized components with digital commercial of the shelf (COTS) cards. This design allows for a scalable system that supports software defined radio (SDR) capabilities. This paper focuses on the RF and digital system design discussing the advantages and disadvantages. The FlexSAR system design objective …

Small Swap 3d Imaging Flash Ladar For Small Tactical Unmanned Air Systems, Alan Bird, Scott A. Anderson, Michael Wojcik, Scott E. Budge

Space Dynamics Laboratory Publications

The Space Dynamics Laboratory (SDL), working with Naval Research Laboratory (NRL) and industry leaders Advanced Scientific Concepts (ASC) and Hood Technology Corporation, has developed a small SWAP (size, weight, and power) 3D imaging flash ladar (LAser Detection And Ranging) sensor system concept design for small tactical unmanned air systems (STUAS). The design utilizes an ASC 3D flash ladar camera and laser in a Hood Technology gyro-stabilized gimbal system. The design is an autonomous, intelligent, geo-aware sensor system that supplies real-time 3D terrain and target images. Flash ladar and visible camera data are processed at the sensor using a custom digitizer/frame …

Single Wavelength Lidar Retrieval Algorithm Of Particulate Matter Concentration Using Celis (Compact Eyesafe Lidar System), A 1.5 Μm Elastic Lidar System, Alan W. Bird, Kori D. Moore, Michael Wojcik, Robert Lemon

Space Dynamics Laboratory Publications

CELiS (Compact Eyesafe Lidar System) is an elastic backscatter light detection and ranging (lidar) system developed for monitoring air quality environmental compliance regarding particulate matter (PM_k) generated from off-road use of wheeled and tracked vehicles as part of the SERDP (Strategic Environmental Research and Development Program) Measurement and Modeling of Fugitive Dust Emission from Off-Road DoD Activities program.

CELiS is small, lightweight and easily transportable for quick setup and measurement of PM_k concentration and emissions. CELiS operates in a biaxial configuration at the 1.5μm eyesafe wavelength with a working range of better than 6 km and range …

Gradient Projection For Interrupted Sar Using The Polar Format Algorithm, Ross Deming, Chad Knight, Jake Gunther

Space Dynamics Laboratory Publications

We present an efficient and computationally simple approach for synthetic aperture radar (SAR) imaging in cases when the radar data have gaps, due to missing pulses and/or notches in the frequency band. Our method is a simple variation of gradient projection, in which the search path in each iteration is obtained by projecting the negative-gradient of the L1 norm onto a hyper-plane defining solutions which are consistent with the data. The computations are not complicated since the L1 gradient is simply equal to the sign() of the pixels in the image. Computational efficiency is obtained by incorporating the polar format …

Clutter Suppression Interferometry System Design And Processing, Chad Knight, Ross Deming, Jake Gunther

Space Dynamics Laboratory Publications

Clutter suppression interferometry (CSI) has received extensive attention due to its multi-modal capability to detect slow-moving targets, and concurrently form high-resolution synthetic aperture radar (SAR) images from the same data. The ability to continuously augment SAR images with geo-located ground moving target indicators (GMTI) provides valuable real-time situational awareness that is important for many applications. CSI can be accomplished with minimal hardware and processing resources. This makes CSI a natural candidate for applications where size, weight and power (SWaP) are constrained, such as unmanned aerial vehicles (UAVs) and small satellites applications.

This paper will discuss the theory for optimal CSI …

Demonstration Of Co2 Ch4 And Pm Detection Using Differentia Absorption Lidar (Dial) Development Of Advanced Air Monitoring Technology For Alberta, Michael Wojcik, Blake Crowther, Robert Lemon, Prasad Valupadas, Long Fu, Bonnie Leung, Zhang Yang, Quamrul Huda, Allan Chambers

Space Dynamics Laboratory Publications

Rapid expansion of the oil and gas industry in Alberta, including the oil sands, has challenged the Alberta Government to keep pace in its efforts to monitor and mitigate the environmental impacts of development. The limitations of current monitoring systems has pushed the provincial government to seek out advanced sensing technologies such as satellite imagery and laser based sensors. The Space Dynamics Laboratory (SDL) of Utah State University, in cooperation with Alberta Environmental Monitoring, Evaluation and Reporting Agency (AEMERA), has developed North America’s first mobile differential absorption lidar (DIAL) system designed specifically for emissions measurement. This instrument is housed inside …

Computational Aerodynamic Analysis Of A Micro-Ct Based Bio-Realistic Fruit Fly Wing, Joshua Brandt, Graham Doig, Naomi Tsafnat

Aerospace Engineering

The aerodynamic features of a bio-realistic 3D fruit fly wing in steady state (snapshot) flight conditions were analyzed numerically. The wing geometry was created from high resolution micro-computed tomography (micro-CT) of the fruit fly Drosophila virilis. Computational fluid dynamics (CFD) analyses of the wing were conducted at ultra-low Reynolds numbers ranging from 71 to 200, and at angles of attack ranging from -10° to +30°. It was found that in the 3D bio-realistc model, the corrugations of the wing created localized circulation regions in the flow field, most notably at higher angles of attack near the wing tip. Analyses …

Uas Capabilities And Performance Modeling For Application Analysis, Brent Terwilliger, Dennis Vincenzi, David Ison, Rene Herron, Todd Smith

Publications

Our team of researchers from Embry-Riddle Aeronautical University-Worldwide has been actively compiling published performance data associated with commercially-off-the-shelf (COTS) group 1 to 3 fixed-wing and vertical takeoff and landing (VTOL) unmanned aircraft systems (UAS) in an effort to develop statistical models of each category. The captured data, which includes maximum speed, cruise speed, endurance, weights, wind limitations, and costs, is used to calculate capabilities including range (one-way and return), time to objective, station keeping duration, maneuver requirements, and derive limited missing information (e.g., component speeds and weights). The benefit from assembling such a unified collection of information and the calculation …

Coreless Planar Transformer Using Low-Temperature Co-Fired Ceramics For Isolated Gate Driver Applications, Matthew W. Feurtado

Electrical Engineering Undergraduate Honors Theses

The aim of this thesis project is to design a signal isolation transformer for gate driver applications using coreless planar transformers (CPT) on a low-temperature co-fired ceramic (LTCC) substrate. To achieve this goal a modulator-demodulator circuit will be selected from several existing designs and an isolation transformer will be designed as a CPT to produce a high frequency high temperature signal isolation for gate driver applications in switching converters, audio drivers, and motor drives. Several designs for coreless planar transformers will be evaluated and tested, and the results will be compared to the theoretical performance obtained from SPICE models for …

A Study On The Micro Electro-Discharge Machining Of Aerospace Materials, Mychal-Drew Moses

Masters Theses & Specialist Projects

Electrical Discharge Machining (EDM) is a non-traditional machining process that uses hundreds of thousands of minute electrical sparks per second to machine any electrically conductive material, no matter the hardness or how delicate it is. EDM allows a much greater range of design possibilities, unconstrained from the traditional machining processes, in which material is removed mechanically by either rotating the cutting tool or the work piece. Shapes that were impossible to machine by any other method, such as deep, precision, square holes and slots with sharp inside corners, are readily produced. It provides accurate geometries in high- aspect ratio holes …

Efficient Method To Cool The Data Center Using Solar Energy, Krishna Ketanbhai Desai

Mechanical and Aerospace Engineering Theses - Archive

Solar energy is the only source which is abundantly available and which can be used to power a cooling system that is based on absorption cycle. Solar cooling system can be used to provide refrigeration for food and medicines and comfort cooling also. Such systems are speci cally applicable to the large applications having large cooling loads for particularly big periods of a year. Peak demand for the cooling of a building and the highest availability of solar radiation are in similar phase, which makes solar cooling of any building a potential energy source and also a green solution. In …

Multiphase Flow Modeling And Analysis Of Filling Process For Pulsed Detonation Engines, Swati Chandran Thirumangalath

Mechanical and Aerospace Engineering Theses - Archive

The filling process of a pulsed detonation engine with fuel and oxidizer should be carried out quickly in order to maintain a high frequency of operation. The objectives of this research were to model an efficient inlet system for filling the detonation tube with fuel/air mixture in stoichiometric ratio and to evaluate various filling schemes. Numerical modeling of the filling process was done using PointwiseTM for meshing and FluentTM as the flow solver, solving the Reynolds-averaged Navier-Stokes equations with a k-? turbulence model. Five different filling configurations were studied, including endwall, normal and angled, opposing and staggered sidewall. The fuel …

A Comparative Study On Micro Electro-Discharge Machining Of Titanium Alloy (Ti-6al-4v) And Shape Memory Alloy (Ni-Ti), Pegah Kakavand

Masters Theses & Specialist Projects

The purpose of this research was to investigate the surface modifications that take place during the machining of NiTi SMA and Ti-6Al-4V with micro-EDM. This was done by creating an array of blind holes and micro-patterns on both work-pieces. To analyze the machined surface and investigate the results, scanning electron microscope (SEM), energy dispersive X- ray spectroscopy (EDS) and X-ray diffraction (XRD) techniques were employed. In addition, the effects of various operating parameters on the machining performance was studied to identify the optimum parameters for micro-EDM of NiTi SMA and Ti-6Al-4V. Recently, aerospace and biomedical industries have placed a high …

Surface Structure And Its Effect On Reducing Drag, Ragini Ramachandran

Doctoral Dissertations and Master's Theses

A miniature subsonic open return wind tunnel was designed and fabricated to measure drag on small test models at low Reynolds numbers. The wind tunnel featured a sensitive strain gauge type load cell. The average drag coefficient of sphere and cube test models were used to validate the miniature wind tunnel, and the values obtained were consistent with published results over the range of Reynolds numbers tested. These initial results gave confidence that the tunnel could be used to study the effects of surface finish on the drag of various models. Several fabrics with differing ribbed surface structures, including a …

Adaptive, Neural And Robust Control Of Wing-Rock And Aeroelastic System, Prince Ghorawat

UNLV Theses, Dissertations, Professional Papers, and Capstones

Modern aircraft exhibit wing-rock phenomenon and aeroelastic instability. Wingrock (roll single degree of freedom motion) and aeroelastic systems' (two degrees of freedom) behavior are described by complex nonlinear differential equations. The nonlinearities in the dynamics of these systems give rise to limit cycle oscillations beyond critical speed of aircraft. The onset of wing-rock and aeroelastic instability limits the performance of aircraft and can even lead to catastrophic consequences. Therefore, control of wing-rock motion and stabilization of aeroelastic systems are important. In the past, several studies have been made and experimental and analytical results have been obtained to explain the wing-rock …

Modeling Of Environmentally Assisted Fatigue Crack Growth Behavior, Sree Phani Chandar Reddy

Dissertations

The formation of fatigue cracks and their propagation due to cyclic loading in metals have been a concern for more than hundred years. Since fatigue failure were first reported by the railroad industry in 1840s, tremendous progress has been achieved in understanding fatigue behavior of metals. But fatigue damage is still a concern due to its complex dependency on various environmental variable like humidity, temperature, time and corrosive environment. Although numerous theories and models have been proposed in the past, the effects of environment on fatigue crack growth (FCG) is not completely understood. This dissertation aims to shed light on …

Simulation Of A Dissimilar Fresnel Relfectarray Antenna, Paul L. Rogers

Electrical Engineering Undergraduate Honors Theses

Planar reflectarray antennas behave similarly to parabolic dish antennas, but are flat in their construction. They work by having areas on the planar surface of different reflection phase, causing the signal to be reflected to a focal point. This is done today by making planar patch antennas with the required reflection phase. These antennas are typically used in aerospace. This paper specifically discusses a planar reflectarray antenna that was originally constructed in Millimeter Wave Circularly Polarized Fresnel Reflector for On-Board Radar on Rescue Helicopters by K. Mazouni. In this paper, the authors eight different shaped antennas to form the planar …

Simulations Of Nanoscale Ni/Al Multilayer Foils With Intermediate Ni2al3 Growth, I. E. Gunduz, S. Onel, C. C. Doumanidis, C. Rebholz, Steven F. Son

Purdue Energetics Research Center Articles

Nanoscale multilayers of binary metallic systems, such as nickel/aluminum, exhibit self-propagating exothermic reactions due to the high formation enthalpy of the intermetallic compounds. Most of the previous modelingapproaches on the reactions of this system rely on the use of mass diffusionwith a phenomenological derived diffusion coefficient representing single-phase (NiAl) growth, coupled with heat transport. We show that the reaction kinetics, temperatures, and thermal front width can be reproduced more satisfactorily with the sequential growth of Ni2Al3 followed by NiAl, utilizing independently obtained interdiffusivities. The computational domain was meshed with a dynamically generated bi-modal grid consisting of fine and coarse zones …

Phased Array Beamsteering In Composite Laminates For Guided Wave Structural Health Monitoring, Peter Osterc

Doctoral Dissertations and Master's Theses

In this study a guided wave phased array beamsteering approach is applied to composite laminates. Current beamsteering algorithms derived for isotropic materials assume omnidirectional wave propagation. Due to inherent anisotropy in composites, guided wave propagation varies with direction and wavefronts no longer have perfect circular shapes.

By examining slowness, velocity and wave curves, as well as amplitude variation with direction for a given composite laminate, the wavefront from a single source can be described as a function of the angle of propagation and distance from origin. Using this approach, a more general delay and sum beamforming algorithm for composite laminates …

Modeling And Simulation Of Radiation From Electronic Transitions In Hypersonic Atmospheric Reentry Flow, Curtis Scholz

Doctoral Dissertations and Master's Theses

A capability for higher accuracy heat transfer modeling in CFD for hypersonic re-entry flows, via inclusion of thermal radiation, is sought. With temperatures reaching tens of thousands of degrees, radiation is known to be significant to chemical reaction rates and thermal boundary layer development, hence surface heat transfer and thermal ablation both to the heat shield and the backshell region of re-entry vehicles. Two current NASA solicitations seek such an improved capability relative to the Mars and Earth entry problems, as uncertainty typically leads to overdesign and excess weight. The present research develops a first physics-based “building block,” which computes …

Supersonic Retro-Propulsion Computational Fluid Dynamics Analysis Applied To Future Mars Mission, Margarita Nataly Brandt

Doctoral Dissertations and Master's Theses

Supersonic Retro-Propulsion is one of the most promising emerging technologies being considered by NASA for use in future Mars missions. This new form of Entry Descent Landing has the potential to help increase the allowable payload mass currently constraining many science instruments and operations. Computational Fluid Dynamics was used to show the feasibility of supersonic retro - propulsion in Mars atmospheric conditions. The results presented show the SRP will be able to perform satisfactory using the same conditions that the Curiosity Rover was exposed to during its landing sequence. The plume expansion was analyzed for various cases, moving from free …