Engineering Commons^™

Thermal Freetop: A Free Open-Source Spacecraft Thermal Analysis Software Package, Yu Tso

Morehead State Theses and Dissertations

A thesis presented to the faculty of the College of Science Morehead State University in partial fulfillment of the requirements for the Degree Master of Science by Yu Tso on April 30, 2018.

Investigation Of Deep Neural Network Image Processing For Cubesat Size Satellites, Adam D. Braun

Morehead State Theses and Dissertations

A thesis presented to the faculty of the College of Science at Morehead State University in partial fulfillment of the requirements for the Degree Master of Science by Adam D. Braun on April 30, 2018.

Multipurpose Glider-Quadcopter Uas, Cody Delarosa, Lucas Richards, Ty Hilton

Senior Design Project For Engineers

The goal for this design was to develop a dual stage UAS that will deliver medical supplies to people in need in remote locations. To accomplish this, a quadcopter was designed to release a glider with the payload therein. A scaled down prototype was produced for analysis purposes. A conceptual model was fully designed that is capable of effectively taking off vertically, accelerating to a desired velocity, releasing the glider, and returning back to the initial takeoff location. The glider was designed to be fully controllable in order to accurately reach the desired location. System aerodynamics and quadcopter propulsion were …

The Controversial F-35 Joint Strike Fighter: America's Most Expensive Weapons System And Its Global Impact, Bert Chapman

Libraries Faculty and Staff Creative Materials

Provides an overview on the F-35 Joint Strike Fighter (JSF) program involving the U.S. and many allied countries. Describes the costs of this program, the technical problems it has experienced, its economic impact on the U.S. and allied countries, the JSF's operational capabilities, potential combat scenarios in which it could be used, and the campaign finance impact aerospace companies and unions have in the electoral process.

Model-Assisted Probability Of Detection Of Flaws In Aluminum Blocks Using Polynomial Chaos Expansions, Xiaosong Du, Leifur Leifsson, Robert Grandin, William Meeker, Ronald Roberts, Jiming Song

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Probability of detection (POD) is widely used for measuring reliability of nondestructive testing (NDT) systems. Typically, POD is determined experimentally, while it can be enhanced by utilizing physics-based computational models in combination with model-assisted POD (MAPOD) methods. With the development of advanced physics-based methods, such as ultrasonic NDT testing, the empirical information, needed for POD methods, can be reduced. However, performing accurate numerical simulations can be prohibitively time-consuming, especially as part of stochastic analysis. In this work, stochastic surrogate models for computational physics-based measurement simulations are developed for cost savings of MAPOD methods while simultaneously ensuring sufficient accuracy. The stochastic …

Numerical Simulation Of A High Strain Rate Biaxial Compression Apparatus, Michael Lagieski

McKelvey School of Engineering Graduate Student Theses & Dissertations

Few experimental methods today are capable of exploring the strength of materials at high strain rates (10⁵ s^-1). Those that are capable, such as the Split Hopkinson Bar, Taylor Anvil and Plate Impact suffer from instability and are generally limited to one dimensional wave propagation. Of particular interest is material response under biaxial compression, similar to that seen in inertial confinement fusion. Laser fusion fuel pellets typically undergo large strain rates as well as plastic deformation and non-linear behavior. This work briefly outlines an experimental procedure designed to replicate these large strain rates under biaxial compression using …

Design Of An Electric Propulsion Thruster Breakout Box System, Ryan Powers

Honors Theses

When performing experiments in the Aerospace Laboratory for Plasma Experiments (ALPE), creating test setups and working with electrical equipment can become dangerous and tedious. A breakout box was required that ensures the ability to troubleshoot electrical problems, decrease the time needed to reconfigure equipment for an experiment, and decrease the potential for a safety hazard. The goal was to design a box that would house most of the equipment necessary to easily obtain current and voltage data from experiments in a safe, reliable manner. Three primary electrical components used in the circuit of the box were the current sensor, the …

Electromagnetic Radiation Shield For Spacecraft, Oseas Hudy-Velasco

Honors Theses

To protect astronauts from high-energy radiation during long-duration missions, an electromagnetic radiation shield was designed and sized for the Orion spacecraft with physical dimensions at a 1:100 scale and magnetic fields and particle energies at a ∼1:10833.3 scale. The electromagnetic radiation shield was simulated in the multi-physics software Comsol using the Magnetic Fields and Particle Tracing modules. The scale model used a DC amperage of 60 A with a 9-turn solenoid wound in three layers and the full-size system used a DC amperage of 6500 A and a 5-layer solenoid of 390 turns per layer. These models generated magnetic fields …

Land, Air, Sea, Rover (Lasr) - Unmanned Vehicle, Gabriel Prescinotti Vivan

Honors Theses

This senior design project encompassed the optimization of a previously built quadcopter, as well as the design of new components for additional functions and increased range of operations. The previous vehicle was designed to operate as a helicopter, land rover, and submarine. Although the vehicle operates successfully in these three environments, it is not very successful on transitioning between them, i.e. cannot take off from underneath water. This year’s project goals included optimizing the current vehicle so that it could transition seamlessly between its functions and adding an additional function: to be able to rover at the bottom of a …

The Water Entry Of Multi-Droplet Streams And Jets, Nathan B. Spiers, Zhao Pan, Jesse Belden, Tadd T. Truscott

Mechanical and Aerospace Engineering Faculty Publications

Water entry has been studied for over a century, but few studies have focused on multiple droplets impacting on a liquid bath sequentially. We connect multi-droplet streams, jets and solid objects with physical-based scaling arguments that emphasize the intrinsically similar cavities. In particular, the cavities created by the initial impact of both droplet streams and jets on an initially quiescent liquid pool exhibit the same types of cavity seal as hydrophobic spheres at low Bond number, some of which were previously unseen for jets and droplet streams. Low-frequency droplet streams exhibit an additional three new cavity seal types unseen for …

Algal Biofuel: The Future Of Green Jet Fuel In Air Transportation, Rajee Olaganathan

Publications

The aviation industry is one of the major contributors for the greenhouse gases. As air travel has become inevitable in this modern era, and fossil fuel usage is not sustainable, it is essential to produce renewable fuel and commercialize it to reduce the greenhouse gas emissions. In order to produce an alternate aviation biofuel a lot of industrial and academic collaborations have been developed worldwide. The main concern of this collaborative research is to produce aviation biofuel from renewable resources with low environmental impacts, and which is sustainable at an economically viable price. This mini-review briefly discusses the biotechnological approaches …

Overview Of The Saber Mission And Launch Vehicle Design, Benjamin Thompson, Jared Fuchs, Grant Randsell, William Hankins, Oakley Copeland, Logan Anderson, Austin Mills, Matt Fletcher, Roman Benetti

Research Horizons Day Posters

No abstract provided.

How Does Spaceflight Affect The Detachment Of Zinc Whiskers?, Kayla Capitan

Research Horizons Day Posters

No abstract provided.

Measurement Of Forces On A Flapping Wing Micro Aerial Vehicle, Darnisha Crane

Research Horizons Day Posters

No abstract provided.

An Exploration Of The Optical Detection Of Ionizing Radiation Utilizing Modern Optics Technology, Sean D. Fournier, Adam Hecht, Cassiano De Oliveira, Jeffrey B. Martin, Richard K. Harrison, Charles Potter

Nuclear Engineering ETDs

Modern ultraviolet (UV) cameras, when combined with UV-transmitting lenses/filter arrangements, can be used to detect radiation dose in air. Ionizing radiation excites nitrogen molecules in ambient air, the resulting decay includes weak emission of ultraviolet photons. Previous work has proven this phenomenon is detectable using highly-sensitive electronically cooled cameras traditionally used in astronomy for low-background imaging. While the ability to detect the presence of radiation (i.e. qualitative measurement) has been demonstrated at Sandia National Laboratories, there are several challenges in correlating images to known dose-fields (quantitative measurement). These challenges include: a low signal to background ratio, interferences due to electronic …

Clutter Suppression For Bistatic Gmti Using Along-Track Interferometry, Ross Deming, Chad Knight

Space Dynamics Laboratory Publications

An adaptation of along-track interferometry (ATI) clutter suppression signal processing is described for bistatic geometries in which the radar transmitter and receivers fly independently on separate platforms. Despite the more complicated geometry, this approach retains the simplicity and computational efficiency of standard monostatic ATI. Bistatic and multi-static (bistatic plus monostatic) geometries can yield significant performance advantages compared with monostatic in terms of detecting and geo-locating moving ground targets. We present results from simulated multi-static data that validate the ATI technique and illustrate the advantages. If time allows, we will also present results from an experimental flight test in the final …

Evaluation Of A Hybrid Reflectance-Based Crop Coefficient And Energy Balance Evapotranspiration Model For Irrigation Management, J. Burdette Barker, Christopher M. U. Neale, Derek M. Heeren, Andrew E. Suyker

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Accurate generation of spatial soil water maps is useful for many types of irrigation management. A hybrid remote sensing evapotranspiration (ET) model combining reflectance-based basal crop coefficients (K_cbrf) and a two-source energy balance (TSEB) model was modified and validated for use in real-time irrigation management. We modeled spatial ET for maize and soybean fields in eastern Nebraska for the 2011-2013 growing seasons. We used Landsat 5, 7, and 8 imagery as remote sensing inputs. In the TSEB, we used the Priestly-Taylor (PT) approximation for canopy latent heat flux, as in the original model formulations. We also used the …

Direct Metal Laser-Sintered Stainless Steel: Comparison Of Microstructure And Hardness Between Different Planes, M. Ghasri-Khouzani, H. Peng, R. Attardo, P. Ostiguy, J. Neidig, R. Billo, D. Hoelzle, M. R. Shankar

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Microstructural analysis and micro-hardness measurements were performed on different planes of 316L stainless steel fabricated by direct metal laser sintering (DMLS) technique. A fine cellular network was observed within the steel microstructure, where morphology of most cells changed from columnar on XZ-plane (vertical section) to equiaxed on XY-plane (horizontal section). Correspondingly, morphology of most grains was found to alter from columnar for the XZ-plane to equiaxed in the case of the XY-plane. Moreover, X-ray diffraction (XRD) analysis revealed a fully austenitic structure for both the planes. The average micro-hardness value for the XZ-plane and XY-plane was insignificantly (≈ 3%) different, …

Ultra Efficient Commercial Transport Challenge- Nasa Design Challenge- X-Jab-Ect, Ramin Abdul, Jacob Beiting, Evan Johnston

Senior Design Project For Engineers

Today’s aircraft require new innovation to be able to produce the same amount of lift, but with the design decrease the amount of drag produced. The X-JAC ECT has the ability and is an innovative airframe to reduce today’s fuel costs. The baseline comparison for the X-JAB is the Boeing 747-400 aircraft, the payload, range, speed, and altitude are the same f or the X-JAB and the 747. Through use of supercritical airfoils, the X-JAB was designed as a blended wing body aircraft to produce more lift while evenly balancing the weight of the aircraft and the payload. Through parametric …

Special Issue: Selected Papers From Idetc 2017, Andreas Mueller, Andrew Murray, Venkat N. Krovi

Mechanical and Aerospace Engineering Faculty Publications

The Mechanisms and Robotics Conference has traditionally provided a vigorous and stimulating international forum for the exchange of technical and scientific information on the theory and practice of mechanical systems. The topical coverage has span areas central to mechanical systems including design (novel mechanisms and robots, synthesis), analysis (kinematics, dynamics, computational approaches, and software systems), applications (from micro-air vehicles, modular robotics, origami applications, medical robotics, to exoskeleton-assistive systems), and educational practices.

Development Of A Self-Orienting Cubesat Solar Array, Eric Mcgill

Honors Theses

The sponsor of this conceptual design project was the Air Force Institute of Technology (AFIT) at WrightPatterson Air Force Base in Dayton, Ohio. AFIT was striving to give CubeSats more capability to conduct research, reconnaissance, and other functions. One of the major barriers for AFIT to overcome to give CubeSats more capability was the ability of the CubeSat to generate usable power while in orbit. All of AFIT’s CubeSats generated the power needed while in orbit with solar panels that are rigidly mounted to the outside of the craft. AFIT believes that a new design for the solar array used …

A Study Of Flight Simulation Training Time, Aircraft Training Time, And Pilot Competence As Measured By The Naval Standard Score, Aaron D. Judy

Doctor of Education (Ed.D)

The purpose of the study was to investigate the relationships between US Navy T-45C flight simulation training time, actual aircraft training time, and intermediate and advanced jet pilot competence as measured by the Naval Standard Score (NSS). Examining the relationships between US Navy T-45C flight simulation time and actual aircraft flight time may provide further information on flight simulation training versus actual aircraft training to aviation authorities, flight instructors, the military aviation community, the commercial aviation community, and academia. The study was non-experimental, correlational, causal-comparative with an emphasis upon the establishment of mathematic and predictive relationships using archival data from …

Influence Of Reverse Shoulder Implant Positioning On Patient-Specific Muscle Forces: A Simulation Study, Kayla Marie Pariser

Honors Theses

A reverse total shoulder arthroplasty (RTSA) is a common treatment used to stabilize the shoulder and improve range of motion in patients with torn rotator cuff muscles. Shoulder stability relies on the shoulder muscles. With rotator cuff tears, the RTSA enables the deltoid muscle to become the primary stabilizer of the shoulder joint. To improve stability, RTSAs increase the deltoid muscle moment arm and decrease the required torque about the shoulder joint for movement. Currently, there is not standardized, objective method for a surgeon to position an implant on a specific patient. This study is part of a larger, ongoing …

Single Axis Stability Autonomous Glider Control, Brian Study

Student Works

To investigate and increase knowledge on autonomous control systems, an autonomous glider was fitted with a control system with the purpose of creating a craft that would be capable of maintaining a wings level condition despite perturbations to the trim condition. The glider measures bank angle and roll rate information from an accelerometer and gyro, before it relays the data to an equipped microcontroller. Programmed on the microcontroller is a control law to take the input from the sensors and issue a command to a single servo that controls both ailerons, allowing for the vehicle to autonomously correct its bank …

Numerical And Analytical Modelling For Droplet Evaporation Resulting In Convective Flow Cooling Verified By Experimentation, Adwaith Ravichandran

Theses and Dissertations

The temperature of a gaseous convective stream can be reduced by injecting a colder liquid into the stream. The extent to which this gas temperature can be reduced depends on the amount of liquid being injected into the gas flow domain, rate of energy transfer (heat) from the gas phase to the liquid resulting in evaporation and the length of the domain itself referred to in this study as a “mixer”. This study proposes the use of a non-dimensional Damkohler number that relates the liquid residence time and the liquid life time which could serve as a yardstick to determine …

Design And Implementation Of An Artificial Neural Network Controller For Quadrotor Flight In Confined Environment, Ahmed Mekky

Mechanical & Aerospace Engineering Theses & Dissertations

Quadrotors offer practical solutions for many applications, such as emergency rescue, surveillance, military operations, videography and many more. For this reason, they have recently attracted the attention of research and industry. Even though they have been intensively studied, quadrotors still suffer from some challenges that limit their use, such as trajectory measurement, attitude estimation, obstacle avoidance, safety precautions, and land cybersecurity. One major problem is flying in a confined environment, such as closed buildings and tunnels, where the aerodynamics around the quadrotor are affected by close proximity objects, which result in tracking performance deterioration, and sometimes instability. To address this …

Distributed Sensing And System Identification Of Cantilever Beams And Plates In The Presence Of Weak Nonlinearities, Patrick Sean Heaney

Mechanical & Aerospace Engineering Theses & Dissertations

While the mathematical foundation for modal analysis of continuous systems has long been established, flexible structures have become increasingly widespread and developing tools for understanding their mechanics has become increasingly important. Cantilever beams and plates, in particular, have been extensively studied due to their practical importance as approximations of more complex structures. The focus of this thesis is on understanding the dynamics of vibrating cantilever beams and plates through analytical and experimental investigation. Various models for the mechanics of these structures, of varying physical fidelity, are described and compared. A fiber optic sensing system is utilized to experimentally acquire distributed …

Determination Of Chemical Notch, KChem On Aluminum And Steel When Subjected Under Slow Strain Rate Test In Corrosive Environment, Joshua Teo Lee Kuok

Masters Theses

When designing for any mechanical components or system, the question would arise as to how the material would react to the loads subjected on it? Would the component survive its service load? How would it react to environmental corrosion? To answer these questions, the technique used in this thesis paper is the Slow Strain Rate Test (SSRT) method. Aluminum and steel were chosen as the material to be tested in this paper. Al 7075-T651, and Al 6061-T651 was chosen due to its wide range of application, high strength to weight ratio and ease of machinability. It is highly used in …

Sysml Output Interface And System-Level Requirement Analyzer For The Horizon Simulation Framework, Viren Kishor Patel

Master's Theses

Model-Based Systems Engineering in industry has been constantly increasing its presence within the aerospace industry. SysML is one such MBSE tool that shows complex system organization and relationships. The Horizon Simulation Framework is another MBSE tool, created by Cal Poly students, that gives users the ability to run “day-in-the-life” simulations of systems. Finding a way to link these two tools could allow systems engineers to reap the benefits of both.

This thesis investigates the background and design process involved with developing the code that can convert an output file generated in SysML, into a format specifically made for the Horizon …

Safety Analysis Of Automatic Dependent Surveillance – Broadcast (Ads-B) System, Rajee Olaganathan

Publications

ADS-B is one of the significant implementation systems of NextGen, to help pilots and air traffic controllers to create a safer, and more efficient National Airspace System (NAS). First, this research paper will briefly describe the ADS-B system, its design structure, ADS-B In and ADS-B Out systems, its efficiency both in pilot applications and in air traffic control applications, and then discuss about the system safety analysis. The preliminary hazard analysis and fault tree analysis will be done for the identified and selected hazards, and will be briefly discussed. The paper will conclude by providing recommendations to prevent/mitigate the hazards …