Engineering Commons^™

Numerical And Scaling Study On Application Of Inkjet Technology To Automotive Coating, Masoud Arabghahestani Dr.

Theses and Dissertations--Mechanical and Aerospace Engineering

A thorough literature review identified lack of precision control over quality of droplets generated by the currently available industrial sprayers and a growing need for higher quality droplets in the coating industry. Particularly, lack of knowledge and understanding in continuous inkjets (CIJ) and drop-on-demand (DOD) technologies is identified as significant. Motivated by these needs, this dissertation is dedicated to computational fluid dynamics (CFD) and scaling studies to improve existing inkjet technologies and develop new designs of efficient coating with single and/or multiple piezoelectric sensors to produce on-demand droplets. This dissertation study aims at developing a new DOD type coating technology, …

In-Situ Characterization Of Burr Formation In Finish Machining Of Inconel 718, Hamzah M. Zannoun

Theses and Dissertations--Mechanical and Aerospace Engineering

One of the undesirable byproducts that occur during the machining process is the development of burrs, which are defined as rough excess material that forms around the geometric discontinuities of a part. Burrs are especially problematic because they have negative impacts across the triple bottom line: economic, environmental, societal. For one, they are expensive to remove because the deburring process is entirely manual and requires skill. Further, burr material is typically discarded which is adding to the already mounting waste generated from machining such as in coolant and chip disposal. Lastly, there are many societal implications, such as operator injury …

Experimental Investigation Of Roughness And Blowing Effects Over Ablator-Like Surfaces, Colby Borchetta

Theses and Dissertations--Mechanical and Aerospace Engineering

Two separate experiments using PIV were carried out to investigate the effects of
roughness and blowing over surfaces geometrically similar to ablation materials used for atmospheric re-entry. The first, water tunnel experiments, employed a dimpled surface similar to AVCOAT, while the second set was completed in a wind tunnel with a material similar to PICA. For the first set, the flow with blowing becomes destabilized, and more disorganized. The blowing disrupts the relatively simple vorticity shedding process and significantly modifies momentum transport via interaction of detached structures. Flow structure and their modifications were examined with a sPOD analysis. The focus …

Formation Control With Collision Avoidance For Fixed-Wing Unmanned Air Vehicles With Speed Constraints, Christopher Heintz

Theses and Dissertations--Mechanical and Aerospace Engineering

Advances in the miniaturization of powerful electronic components and motors, the democratization of global navigation satellite systems (GNSS), and improvements in the performance, safety, and cost in lithium batteries has led to the proliferation of small and relatively inexpensive unmanned aerial vehicles (UAVs). Many of these UAVs are of the multi-rotor design, however, fixed-wing designs are often more efficient than rotary-wing aircraft, leading to a reduction in the power required for a UAV of a given mass to stay airborne. Autonomous cooperation between multiple UAVs would enable them to complete objectives that would be difficult or impossible for a single …

Quantification Of The Aerodynamic Drivers Of A Deployable Propeller, David Malyszek

Electronic Theses and Dissertations, 2020-2023

With the use deployable drones becoming more common research into their improvement is necessary. Deployable drones that are launched from tubes have size limits on the diameter of the propeller during launch and storage. The purpose of this research is to develop deployable propeller blades for practical uses, such as tube launched propeller driven drones and easier to transport wind turbine blades. A deployable propeller will allow for the utilization of larger propellers when a large non-deployable blade isn't an option. Because deployable propellers need to fold, the deployable propeller blades were designed to be hollow and with a slit …

Guiding A Human Follower With Interaction Forces: Implications On Physical Human-Robot Interaction, George L. Holmes, Keyri Moreno Bonnett, Amy Costa, Devin Michael Burns, Yun Seong Song

Psychological Science Faculty Research & Creative Works

This work challenges the common assumption in physical human-robot interaction (pHRI) that the movement intention of a human user can be simply modeled with dynamic equations relating forces to movements, regardless of the user. Studies in physical human-human interaction (pHHI) suggest that interaction forces carry sophisticated information that reveals motor skills and roles in the partnership and even promotes adaptation and motor learning. In this view, simple force-displacement equations often used in pHRI studies may not be sufficient. To test this, this work measured and analyzed the interaction forces (F) between two humans as the leader guided the blindfolded follower …

Calorimetric Measurements Of Lunar Regolith Simulant And Water. An Experimental Study Correlating Weight Percent Water And Temperature Change Through Periods Of Phase Change., George B. Johnson

Dissertations, Master's Theses and Master's Reports

Permanently Shaded Regions (PSRs) are cold traps located around the lunar south pole that have been confirmed to contain possible interesting quantities or volatiles such as H2O, CO2, SO2, CH4, and others. [1] The identification of these volatiles on the lunar surface was a critical step in the development of NASA’s strategic goals for scientific discoveries, sustained space travel and exploration, and re-establishing a human presence on the moon. These volatiles are vital to the future of operating in and exploring space. The LCROSS impact revealed the existence of these resources in PSRs but more information is needed about the …

On The Use Of High-Frequency Surface Wave Oceanographic Research Radars As Bistatic Single-Frequency Oblique Ionospheric Sounders, Stephen R. Kaeppler, Ethan S. Miller, Daniel Cole, Teresa Updyke

CCPO Publications

We demonstrate that bistatic reception of high-frequency oceanographic radars can be used as single-frequency oblique ionospheric sounders. We develop methods that are agnostic of the software-defined radio system to estimate the group range from the bistatic observations. The group range observations are used to estimate the virtual height and equivalent vertical frequency at the midpoint of the oblique propagation path. Uncertainty estimates of the virtual height and equivalent vertical frequency are presented. We apply this analysis to observations collected from two experiments run at two locations in different years, but utilizing similar software-defined radio data collection systems. In the first …

Co2 Based Parachute Deployment, Anthony M. S. Settlemier, Nicholas Motter

Williams Honors College, Honors Research Projects

This paper describes the design process of a CO2 based parachute deployment system for the Akronauts Rocket Design team, with particular emphasis on the selection of methodologies of deployment as well as design iteration. The objective was to create a fully mechanical system in order to replace the black powder based systems that were used previously by the team.

Emphasis was put in creating a system that would function well at higher altitudes while also preventing damage to the parachute during deployment. This system emphasizes robustness under launch conditions.

Neural Network Attitude Control System Design For The Wallops Arc-Second Pointer, Pavel Galchenko, Henry J. Pernicka

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

Heat Generation Of Aircraft Tires At Landing, Yu Li, Dr. Weiji Wang

International Journal of Aviation, Aeronautics, and Aerospace

When the aircraft lands on a runway, the great speed difference between tires and runway causes non-negligible friction and speeds up wheels. The generated heat rapidly raises tire temperature and causes material decomposition, which leads to replacement cost and flight safety issues; the chemical substances in the air can also cause emission problems. Many studies on aircraft tire temperature are based on software simulation or experiments. The simulation result may be affected by unnecessary variables due to cumbersome modelling, and the observation result may be inaccurate due to a particularly dynamic friction process. On the other side, there are few …

Uas For Public Safety: Active Threat Recognition, Joseph Cerreta, Tray Denney, Scott S. Burgess, Anthony Galante, David Thirtyacre, Gloria A. Wilson, Patrick Sherman

International Journal of Aviation, Aeronautics, and Aerospace

The Center for Homeland Defense and Security identified an increase of active threat events, such as mass shootings, annually since 1999. Literature suggests that 90% of shootings were over before law enforcement arrived at the scene and the first responder response was limited to “surround and contain” until Special Weapons and Tactics Teams (SWAT) arrived on the scene. Using Unmanned Aircraft Systems (UAS) to detect which individual was the threat and type of weapon used can provide useful information to increase the speed of the response for first-on-scene rather than waiting for SWAT if the type of weapon was known. …

Modelling Air Quality In An Aircraft Passenger Cabin Using Health Care Standards, Bert Silich

International Journal of Aviation, Aeronautics, and Aerospace

The interest in aerosol contamination of aircraft passenger cabins has increased since the onset of the COVID-19 pandemic. Mathematical models have been developed to help describe how an aerosol behaves in a closed space. The number of infectious particles inhaled is of scientific interest because it can be related to the risk of getting ill from a pathogen. The data required to calculate these results is often difficult to obtain in real world settings. In fact, particle inhalation details are not obtained in the day-to-day routine of a health care environment and are they not required to maintain safety. Hospital …

Anthropometry Considerations In The Design And Evaluation Of Flight Deck Displays And Controls: Literature Review, Robert Joslin

International Journal of Aviation, Aeronautics, and Aerospace

The regulatory requirements and guidance for showing compliance with the Federal Aviation Administration anthropometric considerations in aircraft design are widely dispersed in an array of source documents. Consequently, they are difficult for aircraft manufacturers/applicants to identify, interpret, and address thereby extending the time to certify new/modified aircraft and aircraft systems. This literature review is intended to provide a compendium of the anthropometry considerations in the design certification of displays and controls in aircraft flight decks. This document is not a compliance document and the references herein are frequently updated, hence should be verified by the reader.

Development And Verification Of Flight Data Informed Performance Estimation And Prediction Simulation Tool For Small Electrical Multi-Rotor Uav, Nicholas Scott Borelle

Graduate Theses, Dissertations, and Problem Reports (ETD)

While small scale multi-rotor aircraft are becoming an increasingly large market with applications emerging every day, their ability to have both a high endurance/long range and a high speed/performance flight is severely limited. This leads to uncertainty in mission planning and aircraft design, specifically when deciding mission length and available on-board energy. Uncertainty like this leads to an increased chance of failure to complete the mission, and a failure to recover the aircraft. Considering that these aircraft are used by everyone from hobbyists to commercial companies to military personnel, the applications and missions being flown carry importance and a serious …

Aerodynamic Performance Of A Biologically Inspired Hybrid Plasma-Mechanical Flow Control And Sensing Device, Joseph Dygert

Graduate Theses, Dissertations, and Problem Reports (ETD)

The continued high global demand for passenger and freight air traffic along with increased use of unmanned aerial vehicles operating in broader Reynolds number regimes has resulted in researchers examining alternative technologies, which would result in safer, more reliable, and superior performing aircraft. Aerodynamic flow control may be one of the most promising approaches to solving this problem, having already proven its ability to enable higher flow efficiency while simultaneously improving overall control of flow behavior such as laminar-to-turbulent transition. Recent research in aerodynamic flow control has seen a pronounced growth in the areas of biomimicry and plasma flow control …

Cfd And Heat Transfer Analysis Of Rocket Cooling Techniques On An Aerospike Nozzle, Geoffrey Sullivan

College of Graduate Studies: Theses & Dissertations

In recent years the development of rocket engines has been mainly focused on improving the engine cycle and creating new fuels. Rocket nozzle design has not been changed since the late 1960s. Recent needs for reliable and reusable rockets, as well as advancements in additive manufacturing, have brought new interest into the aerospike nozzle concept. This nozzle is a type of altitude adjusting nozzle that is up to 90% more efficient than bell nozzles at low altitudes and spends up to 30% less fuel. Since the nozzle body is submerged in the hot exhaust gasses it is difficult to keep …

Aerodynamic Characterization Of An Elliptical Fairing In The Wake Of A Bluff Body, Luis Amaya

Electronic Theses and Dissertations, 2020-2023

Aerodynamic optimization is a key step in designing planes, cars, and even buildings. Numerical modeling is used to automate the optimization process and can use different methods to iterate through designs. In this process, consideration of the starting design is paramount as a poor choice can use up computational time and effort. Often, these designs are made with the intention of being out in the open, for which studies on shape variations in freestream situations abound. However, for the case where an object must be placed in the wake of another, there is little research. The study presented here aims …

Wireless Power Transfer In Autonomous Mobile Microgrids, Carl Greene

Dissertations, Master's Theses and Master's Reports

The ability to autonomously dock unmanned ground vehicles plays a key role in mobile micro-grids, where efficient power transfer is paramount. The approach utilized in this work allows for near-field wireless power transfer in remote locations with minimal support. Establishing a micro-grid power system connection autonomously using wireless power eliminates the arduous task of designing a complex, multiple degrees of freedom (MDOF) robotic arm. The work presented in this thesis focuses on both the hardware and software within the micro-grid system. This particular near-field wireless system consists of a primary and secondary set of modules, comprised of Litz wire coils, …

Performance Degradation Based On Importance Change And Application In Dissimilar Redundancy Actuation System, Yadong Zhang, Chao Zhang, Shaoping Wang, Rentong Chen, Mileta M. Tomovic

Engineering Technology Faculty Publications

The importance measure is a crucial method to identify and evaluate the system weak link. It is widely used in the optimization design and maintenance decision of aviation, aerospace, nuclear energy and other systems. The dissimilar redundancy actuation system (DRAS) is a key aircraft control subsystem which performs aircraft attitude and flight trajectory control. Its performance and reliability directly affect the aircraft flight quality and flight safety. This paper considers the influence of the Birnbaum importance measure (BIM) and integrated importance measure (IIM) on the reliability changes of key components in DRAS. The differences of physical fault characteristics of different …

Satellite Drag Coefficient Modeling For Thermosphere Science And Mission Operations, Piyush M. Mehta, Smriti N. Paul, Nicholas H. Crisp, Philip L. Sheridan, Christian Siemes, Günther March, Sean Bruinsma

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Satellite drag modeling remains the largest source of uncertainty affecting space operations in low Earth orbit. The uncertainty stems from inaccurate models for mass density and drag coefficient. Drag coefficient modeling also impacts scientific knowledge on the physics and dynamics of the upper atmosphere through the estimation of high-fidelity mass density from measurements of acceleration on-board satellites. Efforts over the last decade have pushed drag coefficient modeling in the right direction, however, have resulted in multiple methods and tools. We provide a comprehensive review of the drag coefficient modeling methods and tools. Current scale differences between thermospheric data sets mostly …

Effects Of Wheel Rotation On Long-Period Wake Dynamics Of The Drivaer Fastback Model, Matthew Aultman, Rodrigo Auza-Gutierrez, Kevin Disotell, Lian Duan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Lattice Boltzmann method (LBM) simulations were performed to capture the long-period dynamics within the wake of a realistic DrivAer fastback model with stationary and rotating wheels. The simulations showed that the wake developed as a low-pressure torus regardless of whether the wheels were rotating. This torus shrank in size on the base in the case of rotating wheels, leading to a reduction in the low-pressure footprint on the base, and consequently a 7% decrease in the total vehicle drag in comparison to the stationary wheels case. Furthermore, the lateral vortex shedding experienced a long-period switching associated with the bi-stability in …

The Effects Of Geometry And Architecture Of Polymer Matrix Composites On Acoustic Emissions, John J. Bush, Alex D. Swartzentruber, Lukas B. Thompson, Sarah R. Pratt, Chris J. Kuhn

Williams Honors College, Honors Research Projects

The purpose of this project is to study how the variance of the geometry and architecture of polymer matrix composites (PMCs) affect the acoustic emissions measured whilst said structures are subjected to tensile stress. In these tests, a method called Modal AE will be utilized. In Modal AE, some relationships between sources and waves in various materials and geometries are presented in other papers/research. This study will focus on how different thickness and different makeup/ply patterns affect the acoustic emission tests. Some research has been completed and shown how energy attenuation affects the frequency content on PMCs similar to the …

Liquid Engine External Pressurizer (Leep), Emily Armbrust

Williams Honors College, Honors Research Projects

The purpose of this project is to take the current liquid rocket engine test stand design and implement an external pressurant instead of utilizing the 2-phase oxidizer vapor to pressurize itself and the fuel. The purpose behind the design is because the team is limited with the current design concerning burn time due to the amount of propellant they can put in the tanks and the pressure it can reach. The initial pressure is currently not held since there is no external input of mass into the tanks, as the propellant is leaving. Adding an external pressurant allow for the …

Fuel System To Envelope Interface, James Campbell

Williams Honors College, Honors Research Projects

*NOTE THIS PROJECT IS CONFIDENTIAL*

In this project, I will investigate solutions to interfacing a fuel system with a fabric skin section

Large, Complex Housing, Alyssa Carnicella

Williams Honors College, Honors Research Projects

The purpose of this capstone project was to develop a design for a High Voltage Direct Current (HVDC) generator housing with built-in passageways for oil to flow through and cool the machine. The machine should be made using advanced manufacturing. A 3D model concept was designed with the use of SolidWorks. The appropriate hand calculations were completed to ensure that the generator housing would contain the components within itself under various environmental conditions.. The model was then 3D printed to produce a prototype that displays the design features within the housing. The next stage of the project will include completing …

Digital Image Correlation System Design, Verification And Analysis, Tyler Kraft, Matthew J. Riczo, Andrew Chong

Williams Honors College, Honors Research Projects

Two dimensional digital image correlation provides an accurate and effective way to capture strain data on test sections with unusual or oblique geometries. The system requires a camera to record video footage, alignment fixtures and software to convert the footage into strain values. The system works by capturing the video footage of a specific portion of the specimen and comparing the movement of selected pixels. This is all done in the software GOM Correlate and Tracker. This test document outlines the setup, procedure, and validation steps to fulfill this goal. The setup involves a camera, tripod, blue lighting, and laser …

Autonomous Payload Design With Systems Engineering, Michael Downs, Christopher James Liebhart 2nd

Williams Honors College, Honors Research Projects

The design will be an autonomous payload consisting of auto deployment of a drone running an autonomous mission of mapping the terrain around a grounded rocket. The project is part of the Akronauts payload project for the 2022 Spaceport competition. It will include the development of a ground station for monitoring and controlling the drone and the transfer of live data to the station and a computer on board the rocket. The project will aim to use system engineering techniques to accomplish this in the hope of providing documentation and thus insight into the best way to develop a multi-disciplinary …

Schlieren Imaging Of A Supersonic Wind Tunnel, Caleb Townsend, Tayler S. Powell

Williams Honors College, Honors Research Projects

This project exemplifies Schlieren Imaging on a Supersonic Wind Tunnel. Schlieren Imaging allows one to visualize fluid flow by refracting light through a fluid. The Schlieren Imaging system denoted in this paper is used to visualize the shock waves of air onto a test section within a supersonic wind tunnel. This is done by directing a beam of light through a test section and then focusing the light onto a blade edge. This blade edge then breaks up the light beam so that the refractions, created by the pressure differences, are blocked by the knife edge which allows the pressure …

The Design Of The Payload System Of An Aircraft, Ryan Cooper

Williams Honors College, Honors Research Projects

The project group will design and build a system to unload packages for the Zips Aero Design Team's aircraft for the 2021-22 competition year.