Engineering Science and Materials Commons^™

Preparation Of Spent Coffee Grounds-Rubber Composites Using Natural Rubber Latex As Binder, Varittha Mitsaichon, Kanok-On Ruaesrijan, Pranee Phinyocheep, Taweechai Amornsakchai, Preeyanuch Junkong, Sombat Thanawan

Journal of Metals, Materials and Minerals

The aim of this work was to explore the use of natural rubber latex (NRL) as a natural binder (according to the BCG concept) to replace commercial synthetic binders such as polyurethane resin. A composite sheet of spent coffee ground (SCG) and natural rubber (NR) was prepared by mixing of SCG in NRL compounds having concentrations of 30% and 60% dry rubber content (DRC). The amount of SCG in the composites was varied from 33 to 167 part per hundred rubber (phr). The mixture was cast in a mold to form a thin sheet then left drying at room temperature …

Erratum To: In Search For Near-Room-Temperature Superconducting Critical Temperature Of Metal Superhydrides Under High Pressure: A Review, Udomsilp Pinsook

Journal of Metals, Materials and Minerals

No abstract provided.

Fabrication Of Soft Gripper Via Direct Inkjet Writing Additive Manufacturing, Evan D. Johnson

College of Graduate Studies: Theses & Dissertations

Additive manufacturing (AM) has bloomed recently in the manufacturing field due to its many applications. Direct inkjet writing (DIW) is one of the main am technologies used in the production of grippers. DIW is the most popular taking advantage of materials like silicone and hydrogels. The technology of 3D printing with silicone is still in early stages ,nevertheless, the ability to print with soft materials is very alluring. The implementation of complex geometries in the silicone world would yield vast opportunities in the medical and robotics fields. Additive manufacturing allows for this to be thoroughly examined. In this research these …

Construction Of A Peridynamic Model For Viscous Flow, Jiangming Zhao, Adam Larios, Florin Bobaru Ph.D.

Department of Mechanical and Materials Engineering: Faculty Publications

We derive the Eulerian formulation for a peridynamic (PD) model of Newtonian viscous flow starting from fundamental principles: conservation of mass and momentum. This formulation is different from models for viscous flow that utilize the so-called “peridynamic differential operator” with the classical Navier- Stokes equations. We show that the classical continuity equation is a limiting case of the PD one, assuming certain smoothness conditions. The PD model for viscous flow is calibrated to the classical Navier-Stokes equations by enforcing linear consistency for the viscous stress term. Couette and Poiseuille flows, and incompressible fluid flow past a regular lattice of cylinders …

Ultrathin Coding Metasurface For Underwater Wave Focusing, Branching And Self-Bending Generation With One Single Actuator, Lixie Song, Zhong Chen, Mehrdad Negahban, Lei Liang, Zheng Li, Zheng Wu

Department of Mechanical and Materials Engineering: Faculty Publications

A novel metasurface is proposed that aims to generate underwater acoustic waves with various functions by only one actuator. Each metasurface unit consists of an air cavity sandwiched on one side by a vibration plate and connecting rubber supports. By properly selecting the ratio of the plate to unit lengths, a phase shift of π can be attained to constitute a binary coding metasurface. Three demonstrations, including focusing, branching and self-bending waves, are chosen to validate the functionality of the design. The design is also shown to work over a wide frequency range through changing the ratio. In addition, the …

Machine Learning Assisted Metamaterial‑Based Reconfigurable Antenna For Low‑Cost Portable Electronic Devices, Shobhit K. Patel, Jaymit Surve, Vijay Katkar, Juveriya Parmar

Department of Mechanical and Materials Engineering: Faculty Publications

Antenna design has evolved from bulkier to small portable designs but there is a need for smarter antenna design using machine learning algorithms that can meet today’s high growing demand for smart and fast devices. Here in this research, main focus is on developing smart antenna design using machine learning applicable in 5G mobile applications and portable Wi-Fi, Wi-MAX, and WLAN applications. Our design is based on the metamaterial concept where the patch is truncated and etched with a split ring resonator (SRR). The high gain requirement is met by adding metamaterial superstrates having thin wires (TW) and SRRs. The …

Symmetric Or Asymmetric Glide Resistance To Twinning Disconnection?, Mingyu Gong, Houyu Ma, Kunming Yang, Yue Liu, Jian-Feng Nie, Jian Wang

Department of Mechanical and Materials Engineering: Faculty Publications

Successive gliding of twinning disconnections (TDs) creates three-dimensional twins in parent crystal and accommodates shear deformation. It is generally recognized that TD is subject to the same Peierls stress as it glides forward or backward because of its dislocation character and the twofold rotation symmetry of the twin plane. Based on atomistic simulations, we demonstrate that the glide of TDs may be subject to a symmetric or asymmetric resistance corresponding to step character, symmetric resistance for A/A type steps but asymmetric resistance for A/B type steps, where A and B represent crystallographic planes in twin and matrix. Furthermore, we experimentally …

Recent Advances In Biosensors For Detection Of Covid-19 And Other Viruses, Shobhit K. Patel, Jaymit Surve, Juveriya Parmar, Kawsar Ahmed, Francis M. Bui, Fahad Ahmed Al-Zahrani

Department of Mechanical and Materials Engineering: Faculty Publications

This century has introduced very deadly, dangerous, and infectious diseases to humankind such as the influenza virus, Ebola virus, Zika virus, and the most infectious SARS-CoV-2 commonly known as COVID-19 and have caused epidemics and pandemics across the globe. For some of these diseases, proper medications, and vaccinations are missing and the early detection of these viruses will be critical to saving the patients. And even the vaccines are available for COVID-19, the new variants of COVID-19 such as Delta, and Omicron are spreading at large. The available virus detection techniques take a long time, are costly, and complex and …

A Robot-Assisted Acoustofluidic End Effector, Jan Durrer, Prajwal Agrawal, Ali Ozgul, Stephen C.F. Neuhauss, Nitesh Nama, Daniel Ahmed

Department of Mechanical and Materials Engineering: Faculty Publications

Liquid manipulation is the foundation of most laboratory processes. For macroscale liquid handling, both do-it-yourself and commercial robotic systems are available; however, for microscale, reagents are expensive and sample preparation is difficult. Over the last decade, lab-on-a-chip (LOC) systems have come to serve for microscale liquid manipulation; however, lacking automation andmulti-functionality. Despite their potential synergies, each has grown separately and no suitable interface yet exists to link macro-level robotics with micro-level LOC or microfluidic devices. Here, we present a robot-assisted acoustofluidic end effector (RAEE) system, comprising a robotic arm and an acoustofluidic end effector, that combines robotics and microfluidic functionalities.We …

Schaeffler E-Motor, Jenne Harasin, Zachary Zatta, Christopher Tvaroch

Williams Honors College, Honors Research Projects

This project will be focusing on the work accomplished at Schaeffler to convert an existing internal combustion engine, Ford F-250 truck, into a battery electric vehicle. This report focuses on the vehicle's integration with an emphasis on the bearing design, e-Axle housing's method for mounting, bus bar design, resolver design, differential options, wiring for low and high voltage, and oil pump and cooling system for e-Beam. The bearings for the differential as well as the power transmission system from the electric motor to the e-Axle will need to be specified. By late summer 2022, Schaeffler will have a working prototype …

Grinding And Super-Finishing Test Machine Project, Michael Simon

Williams Honors College, Honors Research Projects

A research project in The University of Akron to study grinding and super-finishing of silicon nitride ceramic was initiated by Dr. Siamak Farhad and sponsored by the Timken Company, with the assistance of undergraduate students Michael Simon, Ryan Hosso and Mathew Rozmajzl. The study required analysis of forces and scratches generated during grinding processes of silicon nitride samples. A testing assembly was designed and constructed to record the forces generated during grinding and super-finishing of silicon nitride samples in a computer-numerical-control machine. Silicon nitride samples were subjected to desired grinding and super-finishing operations and all forces generated during the process …

Co2 Based Parachute Deployment, Anthony M. S. Settlemier, Nicholas Motter

Williams Honors College, Honors Research Projects

This paper describes the design process of a CO2 based parachute deployment system for the Akronauts Rocket Design team, with particular emphasis on the selection of methodologies of deployment as well as design iteration. The objective was to create a fully mechanical system in order to replace the black powder based systems that were used previously by the team.

Emphasis was put in creating a system that would function well at higher altitudes while also preventing damage to the parachute during deployment. This system emphasizes robustness under launch conditions.

Permeability, Structural Changes, Flow Regime Transitions In Fuel Cell Catalyst Layers And A Model For Predicting Trapped Saturation For Two-Phase Flow In Porous Media, Karrar Takleef Alofari

Dissertations, Master's Theses and Master's Reports

Proper water management in Proton Exchange Membrane (PEM) fuel cell is important to achieve high performance. Understanding the percolation of the produced water at the cathode catalyst layer (CL) is critical for any robust water management technique. In this study, an ex-situ experimental setup is used to study percolation in the CL at different injection rates and relative humidity (RH) conditions. The results show that increasing the flow rate force the liquid to flow through the bulk of the pores due to the dominant viscous effect. On the other hand, at low injection rates, the capillary becomes dominant and liquid …

Formation Control Of Mobile Robot Swarm In Search Operation, Chanun Asavasirikulkij

Chulalongkorn University Theses and Dissertations (Chula ETD)

The use of swarm mobile robots has emerged as a promising approach to enhance search efficiency in various applications. This thesis focuses on proposing an effective design and fabrication methodology for a swarm mobile robot system based on the Robot Operating System (ROS) framework. Additionally, a novel network architecture is presented to improve communication efficiency among the robots. The primary objective of this research is to investigate the formation control of swarm mobile robots and their superior ability in search operations. Through extensive experiments and quantitative analysis, the performance of the proposed formation control strategy is evaluated in terms of …

Development Of Stiffness Sensing And Adaptive Grasping With Soft Pneumatic Grippers, Chaiwuth Sithiwichankit

Chulalongkorn University Theses and Dissertations (Chula ETD)

This study presents a framework for stiffness sensing and adaptive grasping using soft pneumatic grippers (SPGs). The motivation was to imitate the capabilities of human hands. The challenge was the compliance of soft pneumatic actuators (SPAs). The study associated the behaviors of grasped objects with those on SPAs, introduced a new concept of SPA modeling, and proposed a method for stiffness sensing through SPG pincer grasping. Compression testing was conducted for validation. A technique for forecasting deformation and force on grasped objects based on their stiffness was established, and a control law was elaborated. The presented technique and control architecture …

Simulation And Prototyping Of A Knee Assistive Device For Improved Gait Function, Khemwutta Pornpipatsakul

Chulalongkorn University Theses and Dissertations (Chula ETD)

This study aimed to develop a knee-assistive device while walking. The research was separated into two sections: the gait support simulation in MATLAB and the prototype of the device. Data on body part positions and ground reaction force were collected from three adult Thai participants walking at a speed of 1.5 m/s to calculate knee moment. The simulation section provides support moments during walking using machine learning and artificial stiffness control strategy (MLASCS), composed of the kNN model and the instantaneous artificial stiffness per body mass (IASPB) equations. The MLASCS was used to determine the proper amount of support moment …

ผลกระทบของการเปลี่ยนแปลงอัตราการระบายอากาศตาม ข้อมูลความหนาแน่นของบุคคลในอาคารสำนักงานเพื่อ ป้องกันการแพร่กระจายเชื้อโรคโควิด-19, พิชชาพร ประพิณศรี

Chulalongkorn University Theses and Dissertations (Chula ETD)

การแพร่กระจายเชื้อทางอากาศผ่านระบบทางเดินหายใจเป็นสิ่งที่มนุษย์เผชิญมาตั้งแต่อดีต การควบคุมสภาพแวดล้อมสามารถลดปริมาณเชื้อโรค และความเสี่ยงในการติดเชื้อของผู้ใช้งานพื้นที่ได้ ผู้วิจัยจึงได้พัฒนาแบบจำลองค่าความเสี่ยงในการติดเชื้อร่วมกับดัชนีชี้วัดระยะห่างทางสังคม และประสิทธิภาพอุปกรณ์ป้องกันซึ่งแบบจำลองมีความคลาดเคลื่อนเฉลี่ยเพียง 10.78 เปอร์เซ็นต์จากตัวอย่างสถานการณ์จริงทั้งหมด 11 สถานการณ์ แบบจำลองใช้เป็นเครื่องมือในการวิเคราะห์ความสัมพันธ์ระหว่างความหนาแน่นคนกับอัตราการระบายอากาศในพื้นที่ได้ เพื่อใช้กำหนดมาตรการป้องกันโรคติดต่อ เช่น การกำหนดความหนาแน่นคนในพื้นที่ การกำหนดระยะเวลาเข้าใช้ และการสวมใส่หน้ากากอนามัย ในงานวิจัยนี้วิเคราะห์จำนวนคนที่เหมาะสมในแต่ละพื้นที่เมื่อมีการระบายอากาศที่จำกัด กำหนดให้เป็นไปตามมาตรฐานของ ASHRAE 62.1 และวิเคราะห์หาอัตราการระบายอากาศที่เหมาะสมกับจำนวนคนที่เข้าออกโดยพื้นที่มีการรักษาค่าความเสี่ยงในการติดเชื้อที่ยอมรับได้ พื้นที่ตัวอย่าง คือ พื้นที่สำนักงาน ร้านอาหาร และบาร์ ผลการวิจัยพบว่า เมื่อกำหนดระยะเวลาที่อยู่ในพื้นที่เป็นเวลา 1 – 3 ชั่วโมงและค่าความเสี่ยงในการติดเชื้อไม่เกิน 0.01 – 0.05 ในที่ที่มีการระบายอากาศจำกัด การใส่หน้ากากอนามัยจะรับความหนาแน่นได้สูงกว่าการไม่ใส่หน้ากากอนามัย โดยเพิ่มขึ้นได้ 51.52 – 800.00 เปอร์เซ็นต์เมื่อพิจารณาค่าความเสี่ยงในการติดเชื้อที่ยอมรับได้มีค่าไม่เกิน 0.02 หากยอมรับค่าที่มากขึ้นได้จะทำให้พื้นที่สามารถรับคนได้มากขึ้น ในขณะที่การปรับอัตราการระบายอากาศตามจำนวนคนที่เข้าออกพื้นที่เพื่อรักษาค่าความเสี่ยงในการติดเชื้อให้ไม่เกิน 0.02 ในช่วงเวลาที่อยู่ในพื้นที่ 3 ชั่วโมง การใส่หน้ากากอนามัยจะทำให้สามารถลดอัตราการระบายอากาศลง แต่ยังคงมีค่าสูงกว่าค่าการระบายอากาศมาตรฐาน จึงกล่าวได้ว่า การระบายอากาศตามมาตรฐานมีค่าไม่เพียงพอในการรักษาค่าความเสี่ยงในการติดเชื้อให้ไม่เกิน 0.02 ในช่วงเวลาที่อยู่ในพื้นที่ 3 ชั่วโมง การปรับค่าดังกล่าวส่งผลให้ค่าพลังงานและค่าไฟฟ้าสูง ซึ่งในกรณีไม่ใส่หน้ากากอนามัย และใส่หน้ากากอนามัยสูงกว่าถึง 1,351 – 1,802 และ 169 – 269 เปอร์เซ็นต์ตามลำดับ

Lateral-Torsional Instability And Biaxial Bending Of Imperfect Frp I-Beams, Jodi Knorowski, Stella B. Bondi, Zia Razzaq

Civil & Environmental Engineering Faculty Publications

This paper presents the outcome of a theoretical and experimental study of the behavior of Fiber Reinforced Polymer (FRP) I-beams exposed to lateral-torsional instability or when subjected to biaxial bending. Laboratory experiments involved the application of vertical and horizontal static loads to a 4 x 4 x ¼ in. I-beam with various lengths and the resulting deflections were recorded. Governing biaxial flexure and torsion differential equations were modified to account for the presence of initial imperfections and subsequently solved using a central finite-difference scheme. The theoretical predictions of the beam behavior were found to be in good agreement with what …

Exploring The Effects Of Chip Flexibility On The Behavior Of Standing Seam Diaphragms To Brace Cold Formed Steel Purlins, Michael W. Seek

Engineering Technology Faculty Publications

Cold-formed steel C- and Z-shaped purlins in standing seam roof systems rely on the diaphragm action provided by the panels to restrain lateral movements and thus increase the load carrying capacity the purlins. The clip connection between the purlin and the panel has inherent and sometimes intentional flexibility designed to accommodate thermal deformations. The lateral deformation behavior of standing seam systems supported by Zees is highly nonlinear and this behavior is not well understood. The flexibility has major implications on the transfer of diaphragm forces throughout these systems and simplified models often grossly overpredict the demands on the diaphragm and …

Nb₃Sn Coating Of A 2.6 Ghz Srf Cavity By Sputter Deposition Technique, M. S. Shakel, Wei Cao, H. Elsayed-Ali, G. V. Eremeev, U. Pudasaini, A. M. Valente-Feliciano

Electrical & Computer Engineering Faculty Publications

Nb₃Sn is of interest as a coating for SRF cavities due to its higher transition temperature Tc ~18.3 K and superheating field Hsh ~400 mT, both are twice that of Nb. Nb₃Sn coated cavities can achieve high-quality factors at 4 K and can replace the bulk Nb cavities operated at 2 K. A cylindrical magnetron sputtering system was built, commissioned, and used to deposit Nb₃Sn on the inner surface of a 2.6 GHz single-cell Nb cavity. With two identical cylindrical magnetrons, this system can coat a cavity with high symmetry and uniform thickness. Using Nb-Sn multilayer sequential sputtering followed by …