Engineering Science and Materials Commons^™

Mechanics Of Soft Polymers, Trisha Sain

TechTalks

Understanding the mechanics and physics of soft polymers are essential due to their widespread applications across disciplines. (e.g.-composite materials, bio mechanics, soft robotics etc.) The soft polymers in general inherent lightweight, high stretchability, extreme viscous damping and stimuli responsive behavior. Development of computational modeling strategy to predict their constitutive response, stimuli responsive behavior is indeed helpful for designing novel multifunctional soft composites, artificial mussels/tissues. In this talk I will briefly emphasize how we are developing multiscale-multiphysics based modeling methods for soft polymers to understand their macroscopic deformation mechanism, failure and other mechanical properties. The long term goal is to develop …

Aps Labs (Advanced Power Systems Research Center), Jeffrey D. Naber

TechTalks

Our mission is to promote & facilitate education and research in clean, efficient, and sustainable power and powertrain systems. The center was established in 2007 and in 2014 the 55,000 sq ft APSRC building located near the airport was denoted as a MTU core facility. Our new research contracts in FY2016 were over $2.5M. Our partners include automotive OEMs: GM, Ford, FCA, Toyota, Honda; Commercial OEMs: Cummins, Deere, Detroit, Isuzu, MHI; Suppliers: Delphi, Denso, Borg Warner, Hitachi; and DOE Labs: ANL, ORNL, PNNL, SNL, & INL. We have seven staff to assist in educational and R&D programs and facilities to …

Me-Em Enewsbrief, December 2016, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Structure-Property Relationships Of Polyisobutylene-Block-Polyamide Thermoplastic Elastomers, Morgan Dunn Heskett

Master's Theses

Thermoplastic elastomers (TPEs) are a class of polymer fit for a wide variety of applications due to their customizability. In the synthesis of these types of materials, an elastically-performing polymer, deemed the “soft block,” is combined with a stiffer “hard block” polymer, each of which can be selected based on their own specific properties in order to achieve desired material behavior in the final copolymer. Recently, the use of polyisobutylene as a soft block in combination with a polyamide hard block has been investigated for use in TPE synthesis. While the material showed some promising behavior, many properties were still …

Sulfate Resistance Of Nanosilica Contained Portland Cement Mortars, Iani Batilov Batilov

UNLV Theses, Dissertations, Professional Papers, and Capstones

Soils, sea water and ground water high in sulfates are commonly encountered hostile environments that can attack the structure of concrete via chemical and physical mechanisms which can lead to costly repairs or replacement. Sulfate attack is a slow acting deteriorative phenomenon that can result in cracking, spalling, expansion, increased permeability, paste-to-aggregate bond loss, paste softening, strength loss, and ultimately, progressive failure of concrete. In the presented research study, Portland cement (PC) mortars containing 1.5% to 6.0% nanosilica (nS) cement replacement by weight were tested for sulfate resistance through full submersion in sodium sulfate to simulate external sulfate attack. Mortars …

Alkali-Activated Natural Pozzolan/Slag Binder For Sustainable Concrete, Meysam Najimi

UNLV Theses, Dissertations, Professional Papers, and Capstones

This study aimed to fully replace Portland cement (PC) with environmentally friendly binders capable of improving longevity of concrete. The new binders consisted of different proportions of natural Pozzolan and slag which were alkaline-activated with various combinations of sodium hydroxide and sodium silicate. A step-by-step research program was designed to (1) develop alkali-activated natural Pozzolan/slag pastes with adequate fresh and strength properties, (2) produce alkali-activated natural Pozzolan/slag mortars to assess the effects of dominant variables on their plastic and hardened properties, and (3) finally produce and assess fresh, mechanical, dimensional, transport and durability properties of alkali-activated natural Pozzolan/slag concretes. The …

Self-Patterning Gd Nano-Fibers In Mg-Gd Alloys, Yangxin Li, Jian Wang, Kaiguo Chen, Meiyue Shao, Yao Shen, Li Jin, Guo-Zhen Zhu

Department of Mechanical and Materials Engineering: Faculty Publications

Manipulating the shape and distribution of strengthening units, e.g. particles, fibers, and precipitates, in a bulk metal, has been a widely applied strategy of tailoring their mechanical properties. Here, we report self-assembled patterns of Gd nano-fibers in Mg-Gd alloys for the purpose of improving their strength and deformability. 1-nm Gd nano-fibers, with a 〈c〉-rod shape, are formed and hexagonally patterned in association with Gd segregations along dislocations that nucleated during hot extrusion. Such Gd-fiber patterns are able to regulate the relative activities of slips and twinning, as a result, overcome the inherent limitations in strength and ductility of Mg alloys. …

Spray Printing Of Organic Semiconducting Single Crystals, Grigorios-Panagiotis Rigas, Marcia M. Payne, John E. Anthony, Peter N. Horton, Fernando A. Castro, Maxim Shkunov

Chemistry Faculty Publications

Single-crystal semiconductors have been at the forefront of scientific interest for more than 70 years, serving as the backbone of electronic devices. Inorganic single crystals are typically grown from a melt using time-consuming and energy-intensive processes. Organic semiconductor single crystals, however, can be grown using solution-based methods at room temperature in air, opening up the possibility of large-scale production of inexpensive electronics targeting applications ranging from field-effect transistors and light-emitting diodes to medical X-ray detectors. Here we demonstrate a low-cost, scalable spray-printing process to fabricate high-quality organic single crystals, based on various semiconducting small molecules on virtually any substrate by …

Single Site Robotc Device And Related Systems And Methods, Jack Mondry, Shane M. Farritor, Eric Markvicka, Thomas Frederick, Joseph Bartels

Department of Mechanical and Materials Engineering: Faculty Publications

The embodiments disclosed herein relate to various medical device components, including components that can be incor porated into robotic and/or in vivo medical devices. Certain embodiments include various medical devices for in vivo medical procedures.

Two-Phase Transport In Proton Exchange Membrane Fuel Cells, Kazuya Tajiri

TechTalks

In Multiscale Transport Process Laboratory our research is focused on the experimental and computational analysis of transport phenomena in electrochemical devices and propulsion systems. In this talk our research activity on proton exchange membrane fuel cells (PEMFCs) for automotive application will be explained. Water management is one of the most critical issues in PEMFCs. The water generated in catalyst layer as a product of the electrochemical reaction needs to be removed through porous media by diffusion if it’s vapor, or by capillarity in case of liquid. In flow channels, the liquid water is removed primarily by inertial force of the …

Solid State Sound: A "Hot" Topic, Andrew Barnard

TechTalks

As seen with the latest iPhone 7 release, traditional audio components can now be a limiting factor in technology design. What if we could make a loudspeaker with no moving parts and virtually no weight? Carbon nanotube loudspeakers are such devices. They create sound using heat oscillations, as opposed to a moving diaphragm. They have the thickness of only a handful of carbon atoms, are flexible and stretchable. In this TechTalk I’ll discuss the carbon nanotube loudspeaker and the design challenges in maturing this intriguing technology.

Wearable Electronics, Human-Centered Monitoring, Ye Sarah Sun

TechTalks

Non-contact solution in wearable electronics: A conventional clinical system requires the use of wet electrodes that are in contact with skin using conductive gel to acquire physiological signals. Those systems can acquire high quality signals but may not be feasible for a long-term purpose due to the skin irritation and allergic contact dermatitis. The emerging of human-centered monitoring calls for alternative solutions. Recent technological advances enable capacitive measurement that can acquire signals through cloth or even with an air gap in wearable condition. In this TechTalk I will introduce the non-contact solution in wearable electronics.

Finite Element Simulation Of Pzt-Aided Interrogation Of Composite Laminates Exhibiting Damage, Amany Micheal, Yehia Bahei-El-Din

Centre for Advanced Materials

Piezoelectricity has proved effective in capturing changes in structures caused by various damage mechanisms. In one approach, piezoelectric wafer active sensors (PWAS) are mounted on the surface of the host structure and utilized as both actuators and sensors to interrogate the structure and monitor its health. This is achieved by subjecting the PWAS to a transient electric pulse and reading the resulting voltage. Changes in the stiffness of the substrate due to structural damage affect the response of the PWAS, which could be correlated to integrity of the structure. Applying this technique to fibrous composite laminates encounters particular challenges due …

The Effects Of The Stratosphere On Materials, Ashley C. Greene, Theresa M. Palandro

Posters-at-the-Capitol

Abstract 1:

Making AND Breaking: How reliable are some water pipes?

Ashley C. Greene.

Three different types of pipes were tested to see at what point in time they would break. The pipes, PVC pipe, PEX pipe, and CPVC pipe, were filled with water and attached to a helium filled weather balloon. The ends of the pipes were sealed to trap the water inside. The pipes were secured onto a payload in a Styrofoam box surrounded by cheese cloth. This frame secured the pipes and ensured that they stayed in one place and could not move around the container. The …

Video Capture And Post-Processing Technique For Approximating 3d Projectile Trajectory, Chase M. Pfeifer, Judith M. Burnfield, Guilherme M. Cesar, Max H. Twedt, Jeff A. Hawks

Department of Mechanical and Materials Engineering: Faculty Publications

In this paper we introduce a low-cost procedure and methodology for markerless projectile tracking in three-dimensional (3D) space. Understanding the 3D trajectory of an object in flight can often be essential in examining variables relating to launch and landing conditions. Many systems exist to track the 3D motion of projectiles but are often constrained by space or the type of object the system can recognize (Qualisys, Göteborg, Sweden; Vicon, Oxford, United Kingdom; Opti-Track, Corvallis, Oregon USA; Motion Analysis, Santa Rosa, California USA; Flight Scope, Orlando, Florida USA). These technologies can also be quite expensive, often costing hundreds of thousand dollars. …

Failure Mechanism Of Woven Roving Fabric/Vinyl Ester Composites In Freeze–Thaw Saline Environment, Elias Anis Toubia, Sadra Emami, Donald A. Klosterman

Civil and Environmental Engineering and Engineering Mechanics Faculty Publications

This experimental study investigates the degradation mechanisms of a glass fiber-reinforced plastic material commonly used in civil engineering applications. A substantial reduction in tensile, shear, and compression properties was observed after 100 days of freeze–thaw cycling in saline environment (-20°C to 20°C). Non-destructive inspection techniques were progressively conducted on unexposed (ambient condition) and exposed (conditioned) specimens. The dynamic mechanical analysis showed permanent decrease in storage modulus that was attributed to physical degradation of the polymer and/or fiber–matrix interface. This indicated the formation of internal cracks inside the exposed glass fiber-reinforced plastic laminate. The 3D X-ray tomography identified preferred damage sites …

Research Progress Of Si-Based Anode Materials For Lithium-Ion Batteries, Ding-Qiong Chen, Yang Yang, Qiu-Li Li, Jin-Bao Zhao

Journal of Electrochemistry

Owing to its high theoretical specific capacity (4200 mAh·g^-1), silicon is a promising candidate to replace graphite as the anode in lithium ion batteries (LIBs). However, low intrinsic electric conductivity and dramatic volume change (~ 300%) during the process of lithiation and delithiation result in electrode pulverization and capacity loss with cycling, accordingly, the application of silicon as an anode in LIBs has been severely hindered. We will discuss the structure of silicon electrode including synthesis of Si-based composites,the selection of binder for silicon and the fabrication of binder-free Si-based electrode, as well as the electrolyte additive to …

Research And Application Of Key Materials For Sodium-Ion Batteries, Yong-Chang Liu, Cheng-Cheng Chen, Ning Zhang, Liu-Bin Wang, Xing-De Xiang, Jun Chen

Journal of Electrochemistry

Sodium-ion batteries (SIBs) have been considered as a potential large-scale energy storage technology owing to the abundance, wide distribution, and low price of sodium resources. However, the larger and heavier sodium ion as compared to lithium ion makes it difficult to identify appropriate electrode materials with the capability for fast and stable sodium-ion insertion/extraction. Furthermore, the optimization of electrolyte, the matching of cathode and anode materials, and the construction of sodium-ion full batteries with high-performance, high-safety, and low-cost are urgently needed in order to make SIBs commercially available. This review summarizes the up-to-date research progresses in key materials (including cathode, …

Advances And Prospects Of Lithium-Sulfur Batteries, Shou-Yi Yuan, Ying Pang, Li-Na Wang, Yong-Gang Wang, Yong-Yao Xia

Journal of Electrochemistry

Lithium-sulfur batteries have recently attracted worldwide attention due to the high specific theoretical energy density of sulfur cathode (2600 Wh⋅kg^-1), low cost and wide availability of sulfur. However, the practical application of lithium-sulfur batteries has been hindered by several challenges, such as the shuttling of polysulfide intermediates, the large volume expansion of sulfur during charge/discharge and the dendrites formation on lithium anode. Foremost among these is the shuttling effect arising from the dissolution of lithium polysulfides intermediate into the electrolyte from the cathode reaction and their diffusion to the anode where they react with metal lithium to form …

Micro/Nano-Structured Electrode Materials For Sodium-Ion Batteries, Shuang Yuan, Yun-Hai Zhu, Sai Wang, Tao Sun, Xin-Bo Zhang, Qiang Wang

Journal of Electrochemistry

Sodium has similar physics and chemical properties to lithium, alternatively, sodium (Na)-ion batteries have again aroused a great deal of interest recently, particularly for large-scale stationary energy storage applications due to the practically infinite sodium resources and low cost. However, the technics and materials for Na-ion batteries are immature. Therefore, development of advanced anode and cathode materials for Na-ion batteries is urgently desired but remains a great challenge. This paper briefly reviews some recent progresses in this field, addressing the morphology effects, as well as functions of carbon composite materials toward Na-ion batteries. Several electrode materials with micro/nano-structures based on …