Mechanics of Materials Commons^™

The Study Of Corrosion On Additive-Manufactured Metals., Braydan Daniels

Electronic Theses and Dissertations

The purpose of this study was to investigate and compare the corrosion mechanisms between wrought and additive-manufactured (3D-printed) copper and stainless steel. The experimental procedure consisted of measuring the open circuit potential, electrochemical impedance spectroscopy, linear sweep voltammetry, Tafel analysis, surface topology, and scanning electron microscopy for each metal within salt water, tap water, sulfuric acid, and synthetic body fluid (excluding copper in synthetic body fluid).

Overall, printed stainless steel was more corrosion-resistant than wrought stainless steel in tap water and synthetic body fluid based on OCP, LSV, and surface topology results. Additionally, printed copper was more corrosion-resistant than wrought …

Thermal Behavior Of Plain And Fiber-Reinforced Rigid Concrete Airfield Runways, Arash Karimi Pour

Open Access Theses & Dissertations

The environmental condition and temperature gradient are important factors resulting in concrete airfield runways cracking during the time. Rigid concrete airfield runways experience different thermal gradients during the day and night due to changes in air temperature. Curling and thermal expansion stresses are the main consequences resulting in various types of cracking over the surface and thickness of concrete airfield runways and increasing maintenance costs. The curvature of concrete slabs increases with an increase in the temperature gradient which is amplified when runways open to traffic. Additionally, the combination of the curling and shrinkage stresses, in rare circumstances, can be …

Classification Of Electrical Current Used In Electroplastic Forming, Tyler Grimm

All Dissertations

Electrically assisted manufacturing (EAM) is the direct application of an electric current to a workpiece during manufacturing. This advanced manufacturing process has been shown to produce anomalous effects which extend beyond the current state of modeling of thermal influences. These purported non-thermal effects have collectively been termed electroplastic effects (EPEs).

While there is a distinct difference in results between steady-state (ideal DC) testing and pulsed current testing, the very definition of these two EAM methods has not been well established. A "long" pulse may be considered DC current; a "short" pulse may produce electroplastic effects; and even "steady-state" current shapes …

The Effects Of Laser Shock Peening On The Fatigue Life Of Additive Manufactured Alsi10mg, Jacob L. Biddlecom

All Dissertations

Additive manufacturing (AM) is becoming a manufacturing process that is well established, even with all the resources and attention that has been brought to it, the field is still lacking some key understandings. Currently, there are certain aspects that are difficult to overcome. Some of the intrinsic obstacles include process-induced defects, such as porosity from lack of fusion and gaseous bubble entrapment, as well as complex thermal gradients. These defects can lead to altered material response especially when looking at the fatigue life. The fatigue behaviors of AM components can change from print to print as well as when compared …

Development Of A Fish Robot Equipped With Novel 3d-Printed Soft Bending Actuators, Steven Steele, Jorge Diaz Rodriguez, Sharun Sripathy, Turaj Ashuri, Saleh Gharaie, Yusun Chang, Amir Ali Amiri Moghadam

Symposium of Student Scholars

This paper reports on design and fabrication of a novel soft fish robot. Application of soft actuators for the fish tail will generates continuum bending motion which resembles the natural motion of the fish. However, most soft actuator mechanisms are complex and have low efficiency. Thus, to address this issue we have developed a 3D printed soft bending actuator which can be actuated with an electromotor. The basic design idea of the soft bending actuator is explained, and iteration of the design showed to create the desired motion for the soft tail. The soft actuator has been successfully integrated with …

Editorial: Disease Biomarker Analysis Based On Optical Biosensing, Tianshu Chen, Fanben Meng, Binwu Ying, Xiaoli Zhu

Department of Mechanical and Materials Engineering: Faculty Publications

Disease biomarker analysis has become a crucial tool for diagnosing and evaluating disease prognosis, especially with the increasing understanding of diseases at the molecular level. Abnormalities in various biomarkers can indicate diseased states, and can be used to rapidly and specifically detect and quantify diseases using optical biosensing techniques (Gao et al., 2023). Optical biosensing techniques have several advantages over traditional methods including higher sensitivity, specificity, and faster analysis times (Plikusiene and Ramanaviciene, 2023). It also allows for non-invasive sample collection. With advancements in optical biosensing technology, many medical conditions including cancers, infectious diseases, and autoimmune disorders can be accurately …

Editorial: Disease Biomarker Analysis Based On Optical Biosensing, Tianshu Chen, Fanben Meng, Binwu Ying, Xiaoli Zhu

Department of Mechanical and Materials Engineering: Faculty Publications

Disease biomarker analysis has become a crucial tool for diagnosing and evaluating disease prognosis, especially with the increasing understanding of diseases at the molecular level. Abnormalities in various biomarkers can indicate diseased states, and can be used to rapidly and specifically detect and quantify diseases using optical biosensing techniques (Gao et al., 2023). Optical biosensing techniques have several advantages over traditional methods including higher sensitivity, specificity, and faster analysis times (Plikusiene and Ramanaviciene, 2023). It also allows for non-invasive sample collection. With advancements in optical biosensing technology, many medical conditions including cancers, infectious diseases, and autoimmune disorders can be accurately …

Considering The Influence Of Coronary Motion On Artery‑Specific Biomechanics Using Fluid–Structure Interaction Simulation, Nicholas A. T. Fogell, Miten Patel, Pan Yang, Roosje M. Ruis, David B. Garcia, Jarka Naser, Fotios Savvopoulos, Clint Davies Taylor, Anouk L. Post, Ryan M. Pedrigi, Ranil De Silva, Rob Krams

Department of Mechanical and Materials Engineering: Faculty Publications

The endothelium in the coronary arteries is subject to wall shear stress and vessel wall strain, which influences the biology of the arterial wall. This study presents vessel-specific fluid–structure interaction (FSI) models of three coronary arteries, using directly measured experimental geometries and boundary conditions. FSI models are used to provide a more physiologically complete representation of vessel biomechanics, and have been extended to include coronary bending to investigate its effect on shear and strain. FSI both without- and with-bending resulted in significant changes in all computed shear stress metrics compared to CFD (p = 0.0001). Inclusion of bending within …

A Threshold Helium Leakage Detection Switch With Ultra Low Power Operation, Sulaiman Mohaidat, Fadi M. Alsaleem

Department of Mechanical and Materials Engineering: Faculty Publications

Detecting helium leakage is important in many applications, such as in dry cask nuclear waste storage systems. This work develops a helium detection system based on the relative permittivity (dielectric constant) difference between air and helium. This difference changes the status of an electrostatic microelectromechanical system (MEMS) switch. The switch is a capacitive-based device and requires a very negligible amount of power. Exciting the switch’s electrical resonance enhances the MEMS switch sensitivity to detect low helium concentration. This work simulates two different MEMS switch configurations: a cantilever-based MEMS modeled as a single-degreefreedom model and a clamped-clamped beam MEMS molded using …

A High-Strength Precipitation Hardened Cobalt-Free High-Entropy Alloy, Matthew Luebbe, Jiaqi Duan, Fan Zhang, Jonathan Poplawsky, Hans Pommeranke, Maalavan Arivu, Andrew Hoffman, Mario Buchely, Haiming Wen

Materials Science and Engineering Faculty Research & Creative Works

Recent studies on precipitation-hardened high-entropy alloys (HEAs) demonstrate their high strength and thermal stability, making them promising materials for high-temperature structural applications such as nuclear reactors. However, many existing HEAs contain cobalt (Co), which is unsuitable for nuclear applications because of the long-term activation issue of Co. Co is also expensive and considered a critical material for other applications. Therefore, it is desired to exclude Co from the composition. a Co-free (Fe0.3Ni0.3Mn0.3Cr0.1)88Ti4Al8 HEA was developed and studied in this work. in contrast to previous Co-free HEAs, this alloy is close to Equi atomic in its composition and promises a more …

Crystalline–Amorphous Nanostructures: Microstructure, Property And Modelling, Binqiang Wei, Lin Li, Lin Shao, Jian Wang

Department of Mechanical and Materials Engineering: Faculty Publications

Crystalline metals generally exhibit good deformability but low strength and poor irradiation tolerance. Amorphous materials in general display poor deformability but high strength and good irradiation tolerance. Interestingly, refining characteristic size can enhance the flow strength of crystalline metals and the deformability of amorphous materials. Thus, crystalline–amorphous nanostructures can exhibit an enhanced strength and an improved plastic flow stability. In addition, high-density interfaces can trap radiation-induced defects and accommodate free volume fluctuation. In this article, we review crystalline–amorphous nanocomposites with characteristic microstructures including nanolaminates, core–shell microstructures, and crystalline/amorphous-based dual-phase nanocomposites. The focus is put on synthesis of characteristic microstructures, deformation …

Plasmon Enhanced Quantum Properties Of Single Photon Emitters With Hybrid Hexagonal Boron Nitride Silver Nanocube Systems, Mohammadjavad Dowran, Andrew Butler, Suvechhya Lamichhane, Adam Erickson, Ufuk Kilic, Sy_Hwang Liou, Christos Argyropoulos, A. Laraoui

Department of Mechanical and Materials Engineering: Faculty Publications

Hexagonal boron nitride (hBN) has emerged as a promising ultrathin host of single photon emitters (SPEs) with favorable quantum properties at room temperature, making it a highly desirable element for integrated quantum photonic networks. One major challenge of using these SPEs in such applications is their low quantum efficiency. Recent studies have reported an improvement in quantum efficiency by up to two orders of magnitude when integrating an ensemble of emitters such as boron vacancy defects in multilayered hBN flakes embedded within metallic nanocavities. However, these experiments have not been extended to SPEs and are mainly focused on multiphoton effects. …

Physics-Based Crystal Plasticity Model For Predicting Microstructure Evolution And Dislocation Densities, Juyoung Jeong

LSU Doctoral Dissertations

This work presents three different studies investigating plastic deformation mechanisms in metals and alloys using crystal plasticity finite element (CPFE) modeling. The first study presents a new nonlocal crystal plasticity model for face-centered cubic single crystals under heterogeneous inelastic deformation. The model incorporates generalized constitutive relations that incorporate the thermally activated and drag mechanisms to cover different kinetics of viscoplastic flow in metals and describes the plastic flow and yielding of single-crystals using dislocation densities. The model is compared to micropillar compression experiments for copper single crystals and clarifies the complex microstructural evolution of dislocation densities in metals. The second …

Graphene Twistronics: Tuning The Absorption Spectrum And Achieving Metamaterial Properties, Ammar Armghan, Meshari Alsharari, Khaled Aliqab, Osamah Alsalman, Juveriya Parmar, Shobhit K. Patel

Department of Mechanical and Materials Engineering: Faculty Publications

Graphene twistronics using multilayer graphene is presented in such a way that it provides a metamaterial effect. This manuscript also analyzes the prediction of behavior using machine learning. The metamaterial effect is achieved by twisting the graphene layers. Graphene twistronics is a new concept for changing the electrical and optical properties of bilayer graphene by applying a small angle twist between the layers. The angle twists of 5^o, 10^o, and 15^o are analyzed for the proposed graphene twistronics design. Tuning in the absorption spectrum is achieved by applying small twists to the angles of the …

Heterogeneous Sensor Data Fusion For Multiscale, Shape Agnostic Flaw Detection In Laser Powder Bed Fusion Additive Manufacturing, Benjamin Bevans, Christopher Barrett, Thomas Spears, Aniruddha Gaikwad, Alex Riensche, Harold (Scott) Halliday, Prahalada Rao

Department of Mechanical and Materials Engineering: Faculty Publications

We developed and applied a novel approach for shape agnostic detection of multiscale flaws in laser powder bed fusion (LPBF) additive manufacturing using heterogenous in-situ sensor data. Flaws in LPBF range from porosity at the micro-scale (< 100 μm), layer related inconsistencies at the meso-scale (100 μm to 1 mm) and geometry-related flaws at the macroscale (> 1 mm). Existing data-driven models are primarily focused on detecting a specific type of LPBF flaw using signals from one type of sensor. Such approaches, which are trained on data from simple cuboid and cylindrical-shaped coupons, have met limited success when used for detecting multiscale flaws in complex LPBF parts. The objective of this work is to develop a heterogenous sensor data fusion …

Oh, My Darling Clementine: A Detailed History And Data Repository Of The Los Alamos Plutonium Fast Reactor, Hannah K. Patenaude, Franz J. Freibert

College of Sciences Graduate Student Research

The Los Alamos Plutonium Fast Reactor, Clementine, provided the first fast neutron spectrum using a metallic plutonium fuel system and liquid mercury coolant. Clementine is often mentioned in the history of fast, metal-fueled, or metal-cooled designs, with little public information regarding the specifications or timeline. This paper contains a synopsis of each report regarding the development, operation, experimental results, failures, and subsequent disassembly of Clementine to explore this unique reactor within the context of modern advanced reactor development.

Precious Plastics - Plastic Brick Machine Fabrication, Timothy Ukaobasi Kanu, Evi Paraskevi Troulis

Architectural Engineering

The goal of this research is to determine the structural parameters of the recycled plastic polypropylene when molded into bricks resembling CMU blocks. To accomplish this, three mechanisms had to be assembled: the shredder, the injector, and the 1x1 mold. A tensile and compression test were to be performed on the plastic brick, and the values would be used to compare the tensile and compressive strength of PP plastic bricks, as well as their modulus of elasticity and stress vs. Strain performance. These values would be analyzed to determine whether it would be feasible to build an entire plastic wall. …

Multifunctional Microgel-Based Cream Hydrogels For Postoperative Abdominal Adhesion Prevention, Bo Liu, Yunfan Kong, Olawale A. Alimi, Mitchell Kuss, Huiyin Tu, Wenfeng Hu, Abu Rafay, Kumar Vikas, Wen Shi, Megan Lerner, William L. Berry, Yulong Li, Mark A. Carlson, Bin Duan

Department of Mechanical and Materials Engineering: Faculty Publications

Postoperative abdominal adhesions are a common problem after surgery and can produce serious complications. Current anti-adhesive strategies focus mostly on physical barriers and are unsatisfactory and inefficient. In this study, we designed and synthesized advanced injectable cream-like hydrogels with multiple functionalities, including rapid gelation, self-healing, anti-oxidation, anti-inflammation, and anti-cellular adhesion. The multifunctional hydrogels were facilely formed by the conjugation reaction of epigallocatechin gallate (EGCG) and hyaluronic acid (HA)-based microgels and polyvinyl alcohol (PVA) based on the dynamic boronic ester bond. The physicochemical properties of the hydrogels including anti-oxidative and anti-inflammatory activities were systematically characterized. A mouse cecum-abdominal wall adhesion model …

Surface Characterization Of Particulate Dust Subjected To Dew-Induced Cementation, Mohamed Adawi

Student Theses and Dissertations

Accumulation of soils and other particulate matter on the front cover glass of solar photovoltaic (PV) modules results in transmission losses that detrimentally affect the power output of PV installations. Cementation reactions occur due to interactions between the dust and the glass surface in the presence of temperature, humidity, and ph. In this study, accelerated soiling and cementation tests on glass coupons were performed using a custom instrumented soiling chamber and several standardized soils (Arizona Test Dust, Aramco Test Dust, and China Test Dust) to assess soil adhesion and cementation behaviors. Water contact angle (WCA) and X-ray photoelectron spectroscopy (XPS) …

Interfaces In Dynamic Brittle Fracture Of Pmma: A Peridynamic Analysis, Longzhen Wang, Javad Mehrmashhadi, Florin Bobaru

Department of Mechanical and Materials Engineering: Faculty Publications

Recent experiments in bonded PMMA layers have shown dramatic changes in dynamic crack growth characteristics depending on the interface location and toughness. In this paper we present a peridynamic (PD) analysis of this phenomenon and determine three elements that are essential in a model reproducing the observed fracture behavior: (1) softening near the crack tip to account for changes in PMMA due to heat-generation induced by the high strain rates reached around the crack tip in dynamic fracture; (2) independent extension (mode I) and shear (mode II) modes of fracture; (3) a two-parameter fracture model, which matches both strength and …