Mechanics of Materials Commons^™

A New Angle On Microscopic Suspension Feeders Near Boundaries, Rachel E. Pepper, Marcus Roper, Sangjin Ryu, Nobuyoshi Matsumoto, Moeto Nagai, Howard A. Stone

Department of Mechanical and Materials Engineering: Faculty Publications

Microscopic sessile suspension feeders are a critical component in aquatic ecosystems, acting as an intermediate trophic stage between bacteria and higher eukaryotic taxa. Because they live attached to boundaries, it has long been thought that recirculation of the feeding currents produced by sessile suspension feeders inhibits their ability to access fresh fluid. However, previous models for the feeding flows of these organisms assume that they feed by pushing fluid perpendicular to surfaces they live upon, whereas we observe that sessile suspension feeders often feed at an angle to these boundaries. Using experiments and calculations, we show that living suspension feeders …

Metal-Assisted Etching Of Silicon Molds For Electroforming, Ralu Divan, Dan Rosenthal '14, Karim Ogando, Leonidas E. Ocola, Daniel Rosenmann, Nicolaie Moldovan

Student Publications & Research

Ordered arrays of high-aspect-ratio micro/nanostructures in semiconductors stirred a huge scientific interest due to their unique one-dimensional physical morphology and the associated electrical, mechanical, chemical, optoelectronic, and thermal properties. Metal-assisted chemical etching enables fabrication of such high aspect ratio Si nanostructures with controlled diameter, shape, length, and packing density, but suffers from structure deformation and shape inconsistency due to uncontrolled migration of noble metal structures during etching. Hereby the authors prove that a Ti adhesion layer helps in stabilizing gold structures, preventing their migration on the wafer surface while not impeding the etching. Based on this finding, the authors demonstrate …

Pan Nanofibers And Nanofiber Reinforced Composites, Cheng Ren

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Nanomaterials play an important role in the development of nanotechnology. They possess unique mechanical, physical, and chemical properties coupled with small size and ultrahigh surface area that can provide critical advantages for applications. Continuous nanofibers attract special interest due to their dual nano-macro nature and ability to bridge scales. Nanofibers are being considered for a broad range of applications spanning advanced filters, separation membranes, ultrasensitive sensors, micro/nano actuators, nanoprobes, tissue engineering scaffolds, protective and smart closing, and multifunctional composites. Most of these applications require certain mechanical properties and robustness. However, the literature on the mechanical behavior of nanofibers and their …

The Equi-Biaxial Fatigue Characteristics Of Epdm Under True (Cauchy) Stress Control Conditions, Mark Johnson, Ray Ekins, Niall Murphy, Stephen Jerrams, John Hanley

Conference Papers

ABSTRACT: Strain amplitude control is most often employed when carrying out fatigue testing of rubber components. Often the design engineer requires fatigue test data that is based on load amplitude control. This is analogous to engineering or nominal stress amplitude control. This usually makes it easy to maintain the load within the specified test limits during extended testing. Values of true stress and strain can be obtained from this approach, but the magnitudes of the maximum true stresses in these tests increase with accumulated cycles, whereas the equivalent maximum engineering stress values remain constant. This is easily demonstrated in the …

Materials Education And Research In Art And Design: A New Role For Libraries (Survey Stats), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Program Sheet), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Program Booklet), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Website), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Collection Creation And Administration: A New Role For Libraries (White Paper), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

The Problem/Opportunity: To define, identify, and guide design-based materials collections in academic settings and foster community among those with existing collections and/or those considering creating and supporting one.

Contents and topics:

1. What is a materials collection?
2. Why have a materials collection?
3. Acquisition strategies
4. Organizational approaches
5. Programming possibilities
6. Symposium summary
7. Resources

Beach Wheelchair Project, Rory Aronson, Joshua Marcum, Samuel Coyne, Alex Hayes, Alexa Colburn, Max Hessel, Benedikt Strauss, Marvin Rimmele, Marco Pietsch

Mechanical Engineering

The Beach Wheelchair, Sandcrawler, is a machine intended to help give people with disabilities the full beach experience. The non-profit organization Bridge II Sports sponsored this project, and tasked us with developing the design and fabricating a prototype. This chair has several features including a linkage mechanism that raises and lowers a chair relative to an external frame, hand crank drive with Gates Carbondrive belt and sprockets, buoyant Wheeleez balloon tires, and much more.

Low Velocity Impact Tower Feasibility, Setup, And Impact Testing Of Carbon Fiber Reinforced Epoxy Thermoset And Peek Thermoplastic Matrix Composites, Brent Plehn

Materials Engineering

A low velocity impact tower was donated to Cal Poly's Materials Engineering Department along with four fiber reinforced polymer matrix composites. The tower was set up in building 192 in the Mechanical Testing Laboratory. Improvements were made to the tower including adding velocity detection capabilities, making loose hardware inclusive, adding an extra tower arm for better consistency, adding a double jawed clamp for faster testing, and rerouting the tower's compressed air system to improve performance. A standard operating procedure was drafted, tested, and redrafted for impact testing composite panels. The four composite panels consisted of two quasi-isotropic 16 ply AS-1 …

Thickness-Shear And Thickness-Twist Vibrations Of Circular At-Cut Quartz Resonators, Huijing He, Jiashi Yang, Qing Jiang

Department of Mechanical and Materials Engineering: Faculty Publications

Exact solutions for free vibration frequencies and modes are obtained for thickness-shear and thickness-twist vibrations of unelectroded circular AT-cut quartz plates governed by the two-dimensional scalar differential equation derived by Tiersten and Smythe. Comparisons are made with experimental results and the widely-used perturbation solution by Tiersten and Smythe under the assumption of weak in-plane anisotropy. Our solution is found to be much closer to the experimental results than the perturbation solution . For the frequency of the fundamental thickness- shear mode, the error of the perturbation method is 0.4549%, significant in resonator applications.

Dispersive Waves In Microstructured Solids, A. Berezovski, J. Engelbrecht, A. Salupere, K. Tamm, T. Peets, Mihhail Berezovski

Publications

The wave motion in micromorphic microstructured solids is studied. The mathematical model is based on ideas of Mindlin and governing equations are derived by making use of the Euler–Lagrange formalism. The same result is obtained by means of the internal variables approach. Actually such a model describes internal fields in microstructured solids under external loading and the interaction of these fields results in various physical effects. The emphasis of the paper is on dispersion analysis and wave profiles generated by initial or boundary conditions in a one-dimensional case.

Fatigue Testing And Data Analysis Of Welded Steel Cruciform Joints, Alina Shrestha

LSU New Orleans Theses and Dissertations

In this study, ABS Publication 115, “Guidance on Fatigue Assessment of Offshore Structures” is briefly reviewed. Emphasis is on the S-N curves based fatigue assessment approach of non-tubular joints, and both size and environment effects are also considered. Further, fatigue tests are performed to study the fatigue strength of load-carrying and non-load-carrying steel cruciform joints that represent typical joint types in marine structures. The experimental results are then compared against ABS fatigue assessment methods, based on nominal stress approach, which demonstrates a need for better fatigue evaluation parameter. A good fatigue parameter by definition should be consistent and should correlate …

Stress Analysis Of Ramberg-Osgood And Hollomon 1-D Axial Rods, Ronald J. Giardina Jr

LSU New Orleans Theses and Dissertations

In this paper we present novel analytic and finite element solutions to 1-D straight rods made of Ramberg-Osgood and Hollomon type materials. These material models are studied because they are a more accurate representation of the material properties of certain metals used often in manufacturing than the simpler composite linear types of stress/strain models. Here, various types of loads are considered and solutions are compared against some linear models. It is shown that the nonlinear models do have manageable solutions, which produce important differences in the results - attributes which suggest that these models should take a more prominent place …

Creep, Fatigue And Creep-Fatigue Interactions In Modified 9% Cr - 1% Mo (P91) Steels, Valliappa Kalyanasundaram

Graduate Theses and Dissertations

Grade P91 steel, from the class of advanced high-chrome ferritic steels, is one of the preferred materials for many elevated temperature structural components. Creep-fatigue (C-F) interactions, along with oxidation, can accelerate the kinetics of damage accumulation and consequently reduce such components' life. Hence, reliable C-F test data is required for meticulous consideration of C-F interactions and oxidation, which in turn is vital for sound design practices. It is also imperative to develop analytical constitutive models that can simulate and predict material response under various long-term in-service conditions using experimental data from short-term laboratory experiments. Consequently, the major objectives of the …

Influence Of Microstructure On Thermoelastic Wave Propagation, Arkadi Berezovski, Mihhail Berezovski

Publications

Numerical simulations of the thermoelastic response of a microstructured material on a thermal loading are performed in the one-dimensional setting to examine the influence of temperature gradient effects at the microstructure level predicted by the thermoelastic description of microstructured solids (Berezovski et al. in J. Therm. Stress. 34:413–430, 2011). The system of equations consisting of a hyperbolic equation of motion, a parabolic macroscopic heat conduction equation, and a hyperbolic evolution equation for the microtemperature is solved by a finite-volume numerical scheme. Effects of microtemperature gradients exhibit themselves on the macrolevel due to the coupling of equations of the macromotion …

Improvements In Microdialysis Sampling Extraction Efficiency Using Recycled Flow, Justin Cole Deaton

Graduate Theses and Dissertations

Incomplete recovery during microdialysis sampling is hindering important research in neurology, proteomics, and immunology. Although the current generalized solution, decreasing volumetric flow rates (Q), has been and will remain to be a useful strategy it has reached it's a physical limitation due to evaporation at the collection site. Consequently, many important signaling molecules, such as signaling proteins, remain difficult to study. It is more fundamental to consider relative recovery as a function of the interaction time between the perfusate and the environment surrounding the probe.

In this work an increase in relative recovery was predicted by a mathematical model. Using …

Analysis Of Bolted Joints Under Medium And High Impact Loading, Deepak Sankar Somasundaram, Mohamed Trabia, Brendan J. O'Toole

College of Engineering: Graduate Celebration Programs

• Develop test fixture for medium impact study on bolted joints
• Create FEA model that can replicate the experiment
• Develop test fixture for high impact loading
• Create FEA model and select material properties that can produce results that
  closely match experiments.
• Compare different modeling techniques for high impact loading

Numerical Characterization Of The Hydrodynamics And Thermal Behavior Of Air Flow In A "Flex-Duct" Air Distribution System, Samad Gharehdaghi, Samir Moujaes

College of Engineering: Graduate Celebration Programs

The aim of this research paper is to compute the hydrodynamic and heat transfer characteristics of the air flow inside a flexible duct used for residential/small commercial buildings. Various new information which manufacturers do not provide usually are produced numerically among which heat transfer coefficient, needed for estimating heat loss, is a principal one. Circulation zones in depressions are found to exist. It is shown that these regions act as an insulator and decrease the heat loss along the duct. The results show that fully developed conditions exist much earlier with regard to the inlet for both hydrodynamic and thermal …