Mechanics of Materials Commons^™

Characterization Of Suspension Polymerized Polyacrylamide And Poly(Sodium Acrylate-Acrylamide) Copolymer And Their Size Influence On The Properties Of Concrete, Cole R. Davis, Kendra A. Erk, Stacey L. Kelly

The Summer Undergraduate Research Fellowship (SURF) Symposium

Shrinkage leading to cracking and mechanical instability is a major problem for concrete due to the loss of water during the curing process. However, through the addition of Superabsorbent Polymer (SAP) hydrogels, shrinkage can be prevented, increasing the strength of concrete. Characterization of suspension polymerized polyacrylamide (PAM) poly(sodium acrylate-polyacrylamide) (PANa-PAM) copolymer microsphere sizes, morphology and swelling behavior was conducted before adding them to concrete. Size was determined using microscopy paired with ImageJ analysis. Coulter Counter size characterization was also used to determine the particle size distribution. Swelling behavior was determined using the tea bag method as well as size analysis …

Contribution Of Fiber Undulation To Mechanics Of Three-Dimensional Collagen-I Gel, Shengmao Lin, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

The collagen-I gel is extensively used as a scaffold material in tissue engineering due to its ability to mimic the extracellular matrix (ECM). In this study, the mechanics of collagen-I gel is investigated using a numerical model of three-dimensional collagen network. The resulted mechanical behavior was validated against the published experimental data. Results illustrated that fiber alignment was dominated in the low strain region, and its transition to stretching dominated phenomena at higher strain led to the strain stiffening of collagen gel. The collagen undulation at the microscopic level was found to delay the initiation of strain stiffening

Effects Of Electrode Off Centre On Trapped Thickness-Shear Modes In Contoured At-Cut Quartz Resonators, Junjie Shi, Cuiying Fan, Minghao Zhao, Jiashi S. Yang

Department of Mechanical and Materials Engineering: Faculty Publications

We investigated thickness-shear vibrations of a contoured, AT-cut quartz resonator with a pair of electrodes displaced from the resonator centre. The scalar differential equations by Stevens and Tiersten for thickness-shear vibrations of electroded and unelectroded quartz plates were employed. Based on the variational formulation of the scalar differential equations established in a previous paper and the variation-based Ritz method with trigonometric functions as basis functions, free vibration resonance frequencies and trapped thickness-shear modes were obtained. The effects of the electrode off centre on resonance frequencies and mode shapes were examined. When the electrode off centre is about one hundredth of …

Experimental Building Demonstration Model With Viscous Fluid Dampers, Blake Thomas Reeve, Brianna Jean Kufa, Aden Malek Stepanians, Sophie Carmion Ratkovich

Architectural Engineering

The Architectural Engineering major places a heavy emphasis on structural dynamics and the role of wind and seismic loading in building analysis and design. Buildings of high importance that are critical to community function, such as hospitals, often utilize supplemental damping devices like supplemental viscous fluid dampers or base isolators to reduce the overall demands on the structural system. The design and analysis of these dampers are typically not taught at the undergraduate level, and is frequently performed by mechanical engineers, in lieu of structural engineers.

To better understand and research building behavior with supplemental damping devices, our multi-disciplinary team …

Theory Of Carrier Transport From First Principles: Applications In Photovoltaic And Thermoelectric Materials, Alireza Faghaninia

McKelvey School of Engineering Graduate Student Theses & Dissertations

New sources of energy that are environmentally friendly, cost-effective, and renewable are essential if we are to combat the effects of global climate change. Two of these sources are solar photovoltaic (PV) cells to convert sunlight into electricity and thermoelectric (TE) devices to convert heat to electricity. To be practical on a large scale, the properties (e.g. electrical conductivity, band gap, Seebeck coefficient, etc) of the the underlying materials must be improved significantly through judicious control of structure and composition. Significant understanding of materials properties is required to design and engineer new high-performing materials. First principles calculations using density functional …

Focal Adhesion Kinase Regulation In Stem Cell Alignment And Spreading On Nanofibers, Mohammad Nahid Andalib, Jeong Soon Lee, Ligyeom Ha, Yuris A. Dzenis, Jung Yul Lim

Department of Mechanical and Materials Engineering: Faculty Publications

While electrospun nanofibers have demonstrated the potential for novel tissue engineering scaffolds, very little is known about the molecular mechanism of how cells sense and adapt to nanofibers. Here, we revealed the role of focal adhesion kinase (FAK), one of the key molecular sensors in the focal adhesion complex, in regulating mesenchymal stem cell (MSC) shaping on nanofibers. We produced uniaxially aligned and randomly distributed nanofibers from poly(L-lactic acid) to have the same diameters (about 130 nm) and evaluated MSC behavior on these nanofibers comparing with that on flat PLLA control. C3H10T1/2 murine MSCs exhibited upregulations in FAK expression and …

Nanoscale Frictional Properties Of Nickel With One-Dimensional And Two-Dimensional Materials, Timothy K. Schlenger

Mechanical Engineering Undergraduate Honors Theses

When looking at the nanoscale, material interface interactions have been observed to exhibit particularly interesting properties. Our research looks into various combinations of carbyne and graphene atop a nickel block to look into the interface friction properties between them. Both the carbyne and graphene are tested using steered molecular dynamics (SMD) in sheering and peeling directions along the surface of the nickel block. These tests are then analyzed by comparing the magnitude of the acting force versus the displacement of the carbon allotrope sample across the nickel block. It is found that as the width of a carbon allotrope sample …

Haul Truck Tires Recycling, Jessica N. Lizarazu

Chemical Engineering Undergraduate Honors Theses

The disposal of large Off-the-Road (OTR) tires is an increasingly important concern. These tires can weigh up to 8,450 pounds with an overall diameter and width of approximately 140.7 inches and 45.1 inches respectively. OTR tires are used for mining vehicles such as haul trucks, wheel loaders, backhoes, graders, and trenchers. These new tires cost between $38,000 and $50,000 each, depending on multiple factors including oil prices and the cyclical nature of the industry. Haul trucks contain six tires per vehicle, and mines replace these tires around every 9-12 months. Statistics regarding discarded OTR tires are not provided by the …

Design Of A Folding V-Scraper With Roller For Orchard Applications, Chase Ulrich

BioResource and Agricultural Engineering

This senior project discusses the design of a folding 15 ft. wide leveler for orchard use. This design utilized a category 2 three-point hitch to connect the implement to a tractor. The folding mechanism uses the tractors hydraulic system to actuate the folding movement using hydraulic cylinders. The blades, when wings in operational position, are rigid with one another after some assembly. When the implement is folded the width is reduced to nine feet.

Heating Element Including Carbon Nanotube (Cnt) Layer, Santhosh Kumar Loganathan, Virginie Rollin, Daewon Kim

Publications

Apparatus , materials , and techniques and techniques herein can include providing a deposited layer comprising a com posite material including carbon nanotubes ( CNTs ) . Accord ing to various examples , the composite can be applied to a substrate such as using a solution containing CNTs and other constituents such as sulfur . The solution can be spray applied to a substrate , or spin - coated upon a substrate , such as to provide a uniform , conductive , and optically - transpar ent film layer . In one application , such a film layer can be …

Bending Stiffness In Cadaveric And Composite Long Bones Following Total Joint Replacement, Danielle Gehron, Anderson Adams Ms, Tatsuya Sueyoshi Md, Scott R. Small Ms

Rose-Hulman Undergraduate Research Publications

Several biomechanics studies have utilized commercially available replicate bone models as an alternative to cadaveric tissue specimens, in part due to their ease of handling and reduced expense. In an effort to validate the use of replicate bone specimens in biomechanics research, a number of studies have compared material properties of whole tibia and femur specimens to those of similar cadaveric specimens. Many of these validation studies have ascertained that the material properties of whole bone composite models fall within the range of those properties of cadaveric specimens, while offering reduced interspecimen variability. Current literature lacks, however, the direct comparison …

Ramifications Of Projectile Velocity On The Ballistic Dart Penetration Of Sand, Peter Anthony Sable

Master's Theses (2009 -)

With the advent of novel in-situ experimental measurement techniques, highly resolved quantitative observations of dynamic events within granular media can now be made. In particular, high speed imagery and digital analysis now allow for the ballistic behaviors of sand to be examined not only across a range of event velocities but across multiple length scales. In an attempt to further understand the dynamic behavior of granular media, these new experimental developments were implemented utilizing high speed photography coupled with piezo-electric stress gauges to observe visually accessible ballistic events of a dart penetrating Ottawa sand. Projectile velocities ranged from 100 to …

Thermoelastic Waves In Microstructured Solids, Arkadi Berezovski, Mihhail Berezovski

Publications

Thermoelastic wave propagation suggests a coupling between elastic deformation and heat conduction in a body. Microstructure of the body influences the both processes. Since energy is conserved in elastic deformation and heat conduction is always dissipative, the generalization of classical elasticity theory and classical heat conduction is performed differently. It is shown in the paper that a hyperbolic evolution equation for microtemperature can be obtained in the framework of the dual internal variables approach keeping the parabolic equation for the macrotemperature. The microtemperature is considered as a macrotemperature fluctuation. Numerical simulations demonstrate the formation and propagation of thermoelastic waves in …

Method For Hyper-Polarizing Nuclear Spns At Arbtrary Magnetic Felds, Carlos A. Meriles, Daniela Pagliero, Abdelghani Laraoui

Department of Mechanical and Materials Engineering: Faculty Publications

A method of dynamically polarizing the nuclear spin host of nitrogen-vacancy (NV) centers in diamond is provided. The method uses optical, microwave and radio-frequency pulses to recursively transfer spin polarization from the NV electronic spin. Nitrogen nuclear spin initialization approaching 80% at room temperature is demonstrated both in ensemble and single NV centers without relying on level anti-crossings. This makes the method applicable at arbitrary magnetic fields.

The Design And Construction Of A Torque Measuring Arm For An Air Motor, Logan Dearinger

All Undergraduate Projects

There is a system efficiency lab that sits in the thermodynamics lab of the Mechanical Engineering Technologies department. To expand this lab, a torque measuring device was needed to measure the torsional force that the pump exerts on the air motor. The expansion of this lab is important to give a better understanding of how the different mechanical parts effect the efficiency of the overall system. The first step in the expansion process was the design of a suitable torque measuring device. The most efficient design was a simple one with minimal moving parts. When the air motor is energized …

Temperature-Dependent Helium Ion-Beam Mixing In An Amorphous Sioc/Crystalline Fe Composite, Qing Su, Lloyd Price, Lin Shao, Michael Nastasi

Department of Mechanical and Materials Engineering: Faculty Publications

Temperature dependent He-irradiation-induced ion-beam mixing between amorphous silicon oxycarbide (SiOC) and crystalline Fe was examined with a transmission electron microscope (TEM) and via Rutherford backscattering spectrometry (RBS). The Fe marker layer (7.2 ± 0.8 nm) was placed in between two amorphous SiOC layers (200 nm). The amount of ion-beam mixing after 298, 473, 673, 873, and 1073 K irradiation was investigated. Both TEM and RBS results showed no ion-beam mixing between Fe and SiOC after 473 and 673 K irradiation and a very trivial amount of ion-beam mixing (~2 nm) after 298 K irradiation. At irradiation temperatures higher than 873 …

Active Stiffening Of F-Actin Network Dominated By Structural Transition Of Actin Filaments Into Bundles, Shengmao Lin, Xinwei Han, Gary C.P. Tsui, David Hui, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

Molecular motor regulated active contractile force is key for cells sensing and responding to their mechanical environment, which leads to characteristic structures and functions of cells. The F-actin network demonstrates a two-order of magnitude increase in its modulus due to contractility; however, the mechanism for this active stiffening remains unclear. Two widely acknowledged hypotheses are that active stiffening of F-actin network is caused by (1) the nonlinear force-extension behavior of cross-linkers, and (2) the loading mode being switched from bending to stretching dominated regime. Direct evidence supporting either theory is lacking. Here we examined these hypotheses and showed that a …

Synthesis, Device Fabrication, And Characterization Of Two-Dimensional Molybdenum Disulfide, Gustavo Alberto Lara Saenz

Open Access Theses & Dissertations

The miniaturization of electronic devices according to Moore's Law has been propelled by the continuous demand for faster and smaller devices which continue to advance technology. One recent contribution to this trend was the isolation and characterization of one atom thick of graphite, known as graphene, which led to the Nobel Prize in physics in 2010 being awarded to Andre Geim and Konstantin Novoselov. Graphene and its related nanocarbon derivatives have exceptional mechanical, thermal, optical and electronic properties, making them a potential candidate for electronics and optoelectronics applications. However, this material has no intrinsic bandgap and complicated processes are required …

Improving The Engineering Properties Of Pla For 3d Printing And Beyond, Carmen R. Rocha

Open Access Theses & Dissertations

Additive manufacturing (AM), now more commonly known as 3D printing, has been classified as efficient, fast, and practical in the prototyping sector of product development. In the work presented here, we will use one of the AM techniques known as Material extrusion 3D printing (ME3DP), which has all the advantages of AM. However, one of the biggest challenges facing ME3DP technologies is the limitation of the range of materials used by this technique. Acrylonitrile butadiene styrene (ABS) and poly-lactic acid (PLA) are currently the most common thermoplastics materials used in ME3DP because of their ability to melt and be reprocessed. …

Microstructural Investigation Of Vintage Pipeline Steels Highly Susceptible To Stress Corrosion Cracking, Monica Adriana Torres

Open Access Theses & Dissertations

The use of pipelines for the transmission of gas offers not only efficiency, but a number of economic advantages. Nevertheless, pipelines are subject to aggressive operating conditions and environments which can lead to in-service degradation [1] and thus to failures. These failures can have catastrophic consequences, such as environmental damage and loss of life [2]. One of the most dangerous threats to pipeline integrity is stress corrosion cracking (SCC). Despite the substantial progress that has been achieved in the field, due to the complex nature of this phenomenon there is still not a complete understanding of this form of external …