Process-Structure-Property Relationship In Magnesium-Based Biodegradable Alloy For Biomedical Applications,
2017
University of Texas at El Paso
Process-Structure-Property Relationship In Magnesium-Based Biodegradable Alloy For Biomedical Applications, Pramanshu Trivedi
Open Access Theses & Dissertations
Magnesium alloys are considered to be the next generation of biomaterials because of their ability to degrade in the physiological environment. We elucidate here the impact of multiaxial forging of Mg-2Zn-2Gd alloy on grain refinement to sub-micron regime and relate the structure to mechanical properties and biological functionality. As-cast and annealed samples were multiaxial forged (MAF) for a total number of two passes with a true strain of ~2/pass. Considering that the microstructure governs the biological response of materials, we studied the constituents of the microstructure in conjunction with the mechanical behavior. The antimicrobial behavior in a Mg-2Zn-2Gd alloy with …
Electronic Structure Studies On Transition Metal Containing Endohedral Fullerenes, Carbon Onions And Zinc Sulfide Cages,
2017
University of Texas at El Paso
Electronic Structure Studies On Transition Metal Containing Endohedral Fullerenes, Carbon Onions And Zinc Sulfide Cages, Shusil Bhusal
Open Access Theses & Dissertations
We present the most stable structures for VXSc3-XN@C2n (where X=1-3 and 2n=70, 76, 78 and 80) using a systematic procedure that involves all possible isomers of the host fullerene cages. Subsequently, a detailed investigation of structural and electronic properties of the lowest energy isomers is performed using density functional theory in combination with large polarized Gaussian basis sets. The search procedure developed involved structural optimizations of thousands of fullerenes and correctly identifies the experimentally observed VSc2N@C80 and V2ScN@C80 isomer as the most stable structures. The structural analysis shows that a few V-doped endohedral fullerenes do not follow the isolated pentagon …
On Demand 3d Printed Hybrid Scaffolds For Tissue Engineering Applications,
2017
University of Texas at El Paso
On Demand 3d Printed Hybrid Scaffolds For Tissue Engineering Applications, Ivan D. Hernandez
Open Access Theses & Dissertations
A composite 3D printed polymer scaffold with inbuilt porosity and filled with a hydrogel can provide an ideal support system for cell growth, proliferation, and vascularization. Therefore, a hybrid system of 3D printed polycaprolactone (PCL) scaffold and a hydroxyapatite-based hydrogel was developed for application in the reconstruction of bone defects, which are inherently difficult to repair without any guided therapies. In the present study, a 3D printed gyroid structure of PCL allowed the loading of a higher amount of hydrogel as compared to conventionally used 3D printed mesh structure of the same volume and strut thickness. The hydrogel was composed …
Vorticella: A Protozoan For Bio-Inspired Engineering,
2017
University of Nebraska-Lincoln
Vorticella: A Protozoan For Bio-Inspired Engineering, Sangjin Ryu, Rachel E. Pepper, Moeto Nagai, Danielle C. France
Department of Mechanical and Materials Engineering: Faculty Publications
In this review, we introduce Vorticella as a model biological micromachine for microscale engineering systems. Vorticella has two motile organelles: the oral cilia of the zooid and the contractile spasmoneme in the stalk. The oral cilia beat periodically, generating a water flow that translates food particles toward the animal at speeds in the order of 0.1–1 mm/s. The ciliary flow of Vorticella has been characterized by experimental measurement and theoretical modeling, and tested for flow control and mixing in microfluidic systems. The spasmoneme contracts in a few milliseconds, coiling the stalk and moving the zooid at 15–90 mm/s. Because the …
Controllable Energy Absorption Of Double Sided Corrugated Tubes Under Axial Crushing,
2017
University of Nebraska-Lincoln
Controllable Energy Absorption Of Double Sided Corrugated Tubes Under Axial Crushing, Hozhabr Mozafari, Shengmao Lin, Linxia Gu
Department of Mechanical and Materials Engineering: Faculty Publications
To maximize the controllable energy absorption of corrugation troughs as observed in the single sided corrugated (SSC) tube, we proposed and tested a new structure design, i.e., double-sided corrugated (DSC) tube made of Al 6060-T6 aluminum alloy or CF1263 carbon/epoxy composite. Finite element models were developed to test the mechanical advantage of the DSC tube in comparison with both SSC and classical straight (S) tubes under axial crushing. Results have shown that the total absorbed energy of the DSC aluminum tube with 14 corrugations was 330% and 32% higher than that of the SSC tube with 14 corrugations and the …
Novel Polyethylene Fibers Of Very High Thermal Conductivity
Enabled By Amorphous Restructuring,
2017
Iowa State University
Novel Polyethylene Fibers Of Very High Thermal Conductivity Enabled By Amorphous Restructuring, Bowen Zhu, Jing Liu, Tianyu Wang, Shah R. Valloppilly, Shen Xu, Xinwei Wang
Department of Mechanical and Materials Engineering: Faculty Publications
High-thermal-conductivity polymers are very sought after for applications in various thermal management systems. Although improving crystallinity is a common way for increasing the thermal conductivity (k) of polymers, it has very limited capacity when the crystallinity is already high. In this work, by heat-stretching a highly crystalline microfiber, a significant k enhancement is observed. More interestingly, it coincides with a reduction in crystallinity. The sample is a Spectra S-900 ultrahigh-molecular-weight polyethylene (UHMW-PE) microfiber of 92% crystallinity and high degree of orientation. The optimum stretching condition is 131.5 °C, with a strain rate of 0.0129 s−1 to a low strain ratio …
Dislocations Interaction Induced Structural Instability In
Intermetallic Al2Cu,
2017
Xi’an Jiaotong University
Dislocations Interaction Induced Structural Instability In Intermetallic Al2Cu, Qing Zhou, Jian Wang, Amit Misra, Ping Huang, Fei Wang, Kewei Xu
Department of Mechanical and Materials Engineering: Faculty Publications
Intermetallic precipitates are widely used to tailor mechanical properties of structural alloys but are often destabilized during plastic deformation. Using atomistic simulations, we elucidate structural instability mechanisms of intermetallic precipitates associated with dislocation motion in a model system of Al2Cu. Interaction of non-coplanar <001> dislocation dipoles during plastic deformation results in anomalous reactions—the creation of vacancies accompanied with climb and collective glide of <001> dislocation associated with the dislocation core change and atomic shuffle—accounting for structural instability in intermetallic Al2Cu. This process is profound with decreasing separation of non-coplanar dislocations and increasing temperature and is likely to be …
A Rapid And Non-Invasive Method For Measuring The Peak Positive Pressure Of Hifu Fields By A Laser Beam,
2017
Chongqing Medical University
A Rapid And Non-Invasive Method For Measuring The Peak Positive Pressure Of Hifu Fields By A Laser Beam, Hua Wang, Deping Zeng, Ziguang Chen, Zengtao Yang
Department of Mechanical and Materials Engineering: Faculty Publications
Based on the acousto-optic interaction, we propose a laser deflection method for rapidly, non-invasively and quantitatively measuring the peak positive pressure of HIFU fields. In the characterization of HIFU fields, the effect of nonlinear propagation is considered. The relation between the laser deflection length and the peak positive pressure is derived. Then the laser deflection method is assessed by comparing it with the hydrophone method. The experimental results show that the peak positive pressure measured by laser deflection method is little higher than that obtained by the hydrophone, confirming that they are in reasonable agreement. Considering that the peak pressure …
Benchmark Burnishing With Almen Strip For Surface Integrity,
2017
University of Alabama - Tuscaloosa
Benchmark Burnishing With Almen Strip For Surface Integrity, Z. Y. Liu, C. H. Fu, M. P. Sealy, Y. Zhao, Y. B. Guo
Department of Mechanical and Materials Engineering: Faculty Publications
Burnishing is a surface treatment process widely used in aerospace, navy and other industries to improve fatigue and corrosion resistance by introducing a compressive residual stress layer. The measurement of residual stress by XRD is expensive, time consuming, and tedious. This work presented a quick method to determine the residual stress by using Almen strips. Inspired by the application of Almen strips in shot peening, deflections of burnished Almen strips under different burnishing conditions were measured. It was found that the deflection of Almen strip reflects the magnitude and penetration depth into subsurface of induced stress. Higher burnishing force, smaller …
The Effect Of Number Of Corrugation On Crashworthiness Of Aluminum Corrugated Tube Under Lateral Loading,
2017
University of Nebraska-Lincoln
The Effect Of Number Of Corrugation On Crashworthiness Of Aluminum Corrugated Tube Under Lateral Loading, Hozhabr Mozafari, Arameh Eyvazian, Abdel Magid Hamouda
Department of Mechanical and Materials Engineering: Faculty Publications
Thin-walled tubes have been developed and are growing in use as new energy absorber structures. The objective of this study is to investigate the energy absorption and crushing characteristics of corrugated tubes with different number of corrugation in a specific length exposed to lateral loading. At the first step, experimental tests were carried out on a corrugated tube with three con'ugations (two inner and one outer) and a tube without corrugation. After that, a finite element model was developed by means of ABAQUS software in order to study the effect of corrugation number on crushing properties of thin-walled tubes. The …
Effects Of Aspect Ratio On The Mode Couplings Of Thin-Film Bulk Acoustic Wave Resonators,
2017
Nanjing University of Aeronautics and Astronautics
Effects Of Aspect Ratio On The Mode Couplings Of Thin-Film Bulk Acoustic Wave Resonators, Nian Li, Zhenghua Qian, Jiashi Yang
Department of Mechanical and Materials Engineering: Faculty Publications
We studied mode couplings in thin film bulk acoustic wave resonators of a piezoelectric film on a dielectric layer operating with the fundamental thickness-extensional mode. A system of plate equations derived in our previous paper was used which includes the couplings to the unwanted in-plane extension, flexure, fundamental and second-order thickness shear modes. It was shown that the couplings depend strongly on the plate length/thickness ratio. For a relatively clean operating mode with weak couplings to unwanted modes, a series of discrete values of the plate length/thickness ratio should be avoided and these values were determined in the present paper. …
Experimental Study Of Corrugated Metal-Composite Tubes Under Axial Loading,
2017
Qatar University
Experimental Study Of Corrugated Metal-Composite Tubes Under Axial Loading, Arameh Eyvazian, Hozhabr Mozafari, Abdel Magid Hamouda
Department of Mechanical and Materials Engineering: Faculty Publications
In this study, crushing behavior of corrugated metal-composite tube was examined experimentally under axial loading condition. Six types of specimens, classified into two groups of metal and metal-composite, were tested under quasi static axial loading. The failure mechanism and failure history of the specimens were presented and discussed. The experimental result showed that corrugated metal composite tubes demonstrate perfect energy absorption characteristics in terms of uniformity of load-displacement diagram, reduction of initial peak load and controlling failure mechanism. Moreover, it was also found that adding filament wound layer of composite on the surface of metallic corrugated tube compensated weakness of …
Clustering On Magnesium Surfaces – Formation And Diffusion Energies,
2017
Shanghai University
Clustering On Magnesium Surfaces – Formation And Diffusion Energies, Haijian Chu, Hanchen Huang, Jian Wang
Department of Mechanical and Materials Engineering: Faculty Publications
The formation and diffusion energies of atomic clusters on Mg surfaces determine the surface roughness and formation of faulted structure, which in turn affect the mechanical deformation of Mg. This paper reports first principles density function theory (DFT) based quantum mechanics calculation results of atomic clustering on the low energy surfaces {0001} and {1011}. In parallel, molecular statics calculations serve to test the validity of two interatomic potentials and to extend the scope of the DFT studies. On a {0001} surface, a compact cluster consisting of few than three atoms energetically prefers a facecentered- cubic stacking, to serve as a …
Review Of Sustainability Issues In Non-Traditional Machining
Processes,
2017
University of Nebraska-Lincoln
Review Of Sustainability Issues In Non-Traditional Machining Processes, Kamlakar Rajurkar, H. Hadidi, J. Pariti, G. C. Reddy
Department of Mechanical and Materials Engineering: Faculty Publications
Non-traditional machining processes (such as EDM and ECM) provide alternatives or sometimes the only alternative in generating highly complex 3-D features in very difficult-to -machine materials. This paper reviews recently published work on sustainability issues related to these processes. For example in Electrochemical machining (ECM) the effect of sludge generation and selection of dielectric in Electrodischarge machining (EDM) need to be investigated from the sustainability point of view. All processes need to be studied not only for resulting productivity and accuracy but also their environmental impact during product generation and usage. This paper addresses process mechanisms, surface integrity, sensing and …
Target Lesion Calcium Arc Influence The Performance Of Stenting,
2017
University of Nebraska-Lincoln
Target Lesion Calcium Arc Influence The Performance Of Stenting, Pengfei Dong, Shengmao Lin, David L. Wilson, Hiram G. Bezerra, Linxia Gu
Department of Mechanical and Materials Engineering: Faculty Publications
Percutaneous coronary intervention (PCI) is the most common revascularization procedure, in which, fibrocalcific plaques are found in 17–35% of patients undergoing PCI [1]. Numbers will rise with population aging and prolonged statin treatment. Calcifications often lead to stent under expansion and strut malapposition, with increased risk of thrombosis and in-stent restenosis [2]. Presence of calcium strongly inhibits stent performance, a well-documented metric for outcome [3]. The goal of this work is to develop the finite element models for inspecting the influence of the calcium arc extent on the stenting outcomes, such as the stress and strain distribution within the plaque, …
Accommodation Of The Human Lens Capsule Using A Finite Element Model Based On Nonlinear Regionally
Anisotropic Biomembranes,
2017
University of the Philippines
Accommodation Of The Human Lens Capsule Using A Finite Element Model Based On Nonlinear Regionally Anisotropic Biomembranes, G. David, Ryan M. Pedrigi, J. D. Humphrey
Department of Mechanical and Materials Engineering: Faculty Publications
Accommodation of the eyes, the mechanism that allows humans to focus their vision on near objects, naturally diminishes with age via presbyopia. People who have undergone cataract surgery, using current surgical methods and artificial lens implants, are also left without the ability to accommodate. The process of accommodation is generally well known; however the specific mechanical details have not been adequately explained due to difficulties and consequences of performing in vivo studies. Most studies have modeled the mechanics of accommodation under assumptions of a linearly elastic, isotropic, homogenous lens and lens capsule. Recent experimental and numerical studies showed that the …
Micro/Nanostructures Formation By Femtosecond Laser Surface Processing On Amorphous And Polycrystalline Ni60nb40,
2017
University of Nebraska-Lincoln
Micro/Nanostructures Formation By Femtosecond Laser Surface Processing On Amorphous And Polycrystalline Ni60nb40, Edwin Peng, Alfred Tsubaki, Craig A. Zuhlke, Meiyu Wang, Ryan Bell, Michael J. Lucis, Troy P. Anderson, Dennis R. Alexander, George Gogos, Jeffrey E. Shield
Department of Mechanical and Materials Engineering: Faculty Publications
Femtosecond laser surface processing is a technology that can be used to functionalize many surfaces, imparting specialized properties such as increased broadband optical absorption or superhydrophilicity/superhydrophobicity. In this study, two unique classes of surface structures, below surface growth (BSG) and above surface growth (ASG) mounds, were formed by femtosecond laser surface processing on amorphous and polycrystalline Ni60Nb40 with two different grain sizes. Cross sectional imaging of these mounds revealed thermal evidence of the unique formation processes for each class of surface structure. BSG mounds formed on all three substrates using the same laser parameters had similar surface …
Growth Mechanisms Of Multiscale, Mound-Like Surface Structures
On Titanium By Femtosecond Laser Processing,
2017
University of Nebraska-Lincoln
Growth Mechanisms Of Multiscale, Mound-Like Surface Structures On Titanium By Femtosecond Laser Processing, Edwin Peng, Ryan Bell, Craig A. Zuhlke, Meiyu Wang, Dennis R. Alexander, George Gogos, Jeffrey E. Shield
Department of Mechanical and Materials Engineering: Faculty Publications
Femtosecond laser surface processing (FLSP) can be used to functionalize many surfaces, imparting specialized properties such as increased broadband optical absorption or superhydrophobicity/-hydrophilicity. In this study, the subsurface microstructure of a series of mound-like FLSP structures formed on commercially pure titanium using five combinations of laser fluence and cumulative pulse counts was studied. Using a dual beam Scanning Electron Microscope with a Focused Ion Beam, the subsurface microstructure for each FLSP structure type was revealed by cross-sectioning. The microstructure of the mounds formed using the lowest fluence value consists of the original Ti grains. This is evidence that preferential laser …
Robotic Surgical Devices, Systems, And Related Methods,
2017
University of Nebraska-Lincoln
Robotic Surgical Devices, Systems, And Related Methods, Shane M. Farritor, Erik Mumm, Philip Chu, Nishant Kumar, Jason Dumpert, Yutaka Tsutano
Department of Mechanical and Materials Engineering: Faculty Publications
The embodiments disclosed herein relate to various medical device components, including components that can be incorporated into robotic and/or in vivo medical devices. Certain embodiments include various modular medical devices for in vivo medical procedures.
Methods , Systems , And Devices
Relating To Surgical End Effectors,
2017
University of Nebraska-Lincoln
Methods , Systems , And Devices Relating To Surgical End Effectors, Shane M. Farritor, Tom Fredrick, Joe Bartels
Department of Mechanical and Materials Engineering: Faculty Publications
The embodiments disclosed herein relate to various medical device components, including components that can be incorporated into robotic and/or in vivo medical devices, and more specifically including end effectors that can be incorporated into such devices. Certain end effector embodiments include various vessel cautery devices that have rotational movement as well as cautery and cutting functions while maintaining a relatively compact structure. Other end effector embodiments include various end effector devices that have more than one end effector.
