Glocal Integrity In 420 Stainless Steel By Asynchronous Laser Processing,
2019
University of Nebraska-Lincoln
Glocal Integrity In 420 Stainless Steel By Asynchronous Laser Processing, Michael P. Sealy, Haitham Hadidi, Cody Kanger, X. L. Yan, Bai Cui, J. A. Mcgeough
Department of Mechanical and Materials Engineering: Faculty Publications
Cold working individual layers during additive manufacturing (AM) by mechanical surface treatments, such as peening, effectively “prints” an aggregate surface integrity that is referred to as a glocal (i.e., local with global implications) integrity. Printing a complex, pre-designed glocal integrity throughout the build volume is a feasible approach to improve functional performance while mitigating distortion. However, coupling peening with AM introduces new manufacturing challenges, namely thermal cancellation, whereby heat relaxes favorable residual stresses and work hardening when printing on a peened layer. Thus, this work investigates glocal integrity formation from cyclically coupling LENS® with laser peening on 420 stainless steel.
The Role Of Low-Level Image Features In The
Affective Categorization Of Rapidly Presented
Scenes,
2019
State University of New York at Binghamton
The Role Of Low-Level Image Features In The Affective Categorization Of Rapidly Presented Scenes, L. Jack Rhodes, Matthew Rios, Jacob M. Williams, Gonzalo Quinones, Prahalada K. Rao, Vladimir Miskovic
Department of Mechanical and Materials Engineering: Faculty Publications
It remains unclear how the visual system is able to extract affective content from complex scenes even with extremely brief (< 100 millisecond) exposures. One possibility, suggested by findings in machine vision, is that low-level features such as unlocalized, two-dimensional (2-D) Fourier spectra can be diagnostic of scene content. To determine whether Fourier image amplitude carries any information about the affective quality of scenes, we first validated the existence of image category differences through a support vector machine (SVM) model that was able to discriminate our intact aversive and neutral images with ~ 70% accuracy using amplitude-only features as inputs. This model allowed us to confirm that scenes belonging to different affective categories could be mathematically distinguished on the basis of amplitude spectra alone. The next question is whether these same features are also exploited by the human visual system. Subsequently, we tested observers’ rapid classification of affective and neutral naturalistic scenes, presented briefly (~33.3 ms) and backward masked with synthetic textures. We tested categorization accuracy across three distinct experimental conditions, using: (i) original images, (ii) images having their amplitude spectra swapped within a single affective image category (e.g., an aversive image whose amplitude spectrum has been swapped with another aversive image) or (iii) images having their amplitude spectra swapped between affective categories (e.g., an aversive image containing the amplitude spectrum of a neutral image). Despite its discriminative potential, the human visual system does not seem to use Fourier amplitude differences as the chief strategy for affectively categorizing scenes at a glance. The contribution of image amplitude to affective categorization is largely dependent on interactions with the phase spectrum, although it is impossible to completely rule out a residual role for unlocalized 2-D amplitude measures.
Compliant Surgical Graspers And Methods Of Making And Using,
2019
Lincoln, NE
Compliant Surgical Graspers And Methods Of Making And Using, Carl Nelson, Alan Goyzueta
Department of Mechanical and Materials Engineering: Faculty Publications
This disclosure describes compliant graspers for use in endoscopic surgeries.
Self-Powered Ghz Solution-Processed Hybrid Perovskite Photodetectors,
2019
Lincoln, NE
Self-Powered Ghz Solution-Processed Hybrid Perovskite Photodetectors, Jinsong Huang
Department of Mechanical and Materials Engineering: Faculty Publications
Organic-inorganic hybrid perovskite (OIHP) based photo-responsive devices include an OIHP active layer disposed between a cathode layer and an anode layer, and an electron extraction layer disposed between the cathode layer and the active layer. The electron extraction layer includes a layer of C60 directly disposed on the active layer. The active layer includes an organometal trihalide perovskite layer (e.g., CH3NH3PbI2X, where X includes at least one of Cl, Br, or I).
9r Phase Enabled Superior Radiation Stability Of Nanotwinned Cu Alloys Via In Situ Radiation At Elevated Temperature,
2019
Purdue University
9r Phase Enabled Superior Radiation Stability Of Nanotwinned Cu Alloys Via In Situ Radiation At Elevated Temperature, Cuncai Fan, Dongyue Xie, Jin Li, Zhongxia Shang, Youxing Chen, Sichuang Xue, Jian Wang, Meimei Li, Anter El-Azab, Haiyan Wang, Xinghang Zhang
Department of Mechanical and Materials Engineering: Faculty Publications
Nanotwinned metals exhibit outstanding radiation tolerance as twin boundaries effectively engage, transport and eliminate radiation-induced defects. However, radiation-induced detwinning may reduce the radiation tolerance associated with twin boundaries, especially at elevated temperatures. Here we show, via in-situ Kr ion irradiation inside a transmission electron microscope, that 3 at. % Fe in epitaxial nanotwinned Cu (Cu97Fe3) significantly improves the thermal and radiation stability of nanotwins during radiation up to 5 displacements-per-atom at 200 °C. Such enhanced stability of nanotwins is attributed to a diffuse 9R phase resulted from the dissociation of incoherent twin boundaries in nanotwinned Cu …
Study Of Behavior Of Plastic Modified Bitumen By Incorporating Carbon Black,
2019
Technological and Higher Education Institute of Hong Kong (THEi)
Study Of Behavior Of Plastic Modified Bitumen By Incorporating Carbon Black, Ho-Fai Wong, Hao-Jue Hong, Lai-Ming Leung, Tsz-Chun Fong, Yi-Fei Shen, Tsz-Hin Lo
Faculty of Science & Technology (THEi)
In recent years, the performance of polymer modified bitumen has been widely studied. This study reports a research carried out to investigate the properties of polymer modified bitumen (PMB) by using polypropylene as modifier, carbon black as additives, to examine the optimum ratio of polypropylene to carbon black. With this objective, sample preparation using wet mixing method combining high shear mix was firstly performed. Subsequently, 18 samples were developed for the study, of which the polypropylene (PP) contents 10%, 12%, 14%, 16%, 18% and 20% with 2%, 3%, 4% of carbon black content. Afterwards, samples were characterized by standard tests …
Relative Contributions Of Intracranial Pressure And Intraocular
Pressure On Lamina Cribrosa Behavior,
2019
University of Nebraska-Lincoln
Relative Contributions Of Intracranial Pressure And Intraocular Pressure On Lamina Cribrosa Behavior, Junfei Tong, Deepta Ghate, Sachin Kedar, Linxia Gu
Department of Mechanical and Materials Engineering: Faculty Publications
Purpose. To characterize the relative contributions of intraocular pressure (IOP) and intracranial pressure (ICP) on lamina cribrosa (LC) behavior, specifically LC depth (LCD) and LC peak strain. Methods. An axially symmetric finite element model of the posterior eye was constructed with an elongated optic nerve and retro-orbital subarachnoid space ensheathed by pia and dura mater. -e mechanical environment in LC was evaluated with ICP ranging from 5 to 15mmHg and IOP from 10 to 45 mmHg. LCD and LC peak strains at various ICP and IOP levels were estimated using full factorial experiments. Multiple linear regression analyses were …
Design Rules For Additive Manufacturing – Understanding The
Fundamental Thermal Phenomena To Reduce Scrap,
2019
University of Nebraska-Lincoln
Design Rules For Additive Manufacturing – Understanding The Fundamental Thermal Phenomena To Reduce Scrap, M. Reza Yavari, Kevin D. Cole, Prahalada K. Rao
Department of Mechanical and Materials Engineering: Faculty Publications
The goal of this work is to predict the effect of part geometry and process parameters on the direction and magnitude of heat flow heat flux in parts made using metal additive manufacturing (AM) processes. As a step towards this goal, the objective of this paper is to develop and apply the mathematical concept of heat diffusion over graphs to approximate the heat flux in metal AM parts as a function of their geometry. This objective is consequential to overcome the poor process consistency and part quality in AM. Currently, part build failure rates in metal AM often exceed 20%, …
Cmas/Volcanic Ash Infiltration Performance Of Yttria Rich-Zirconia Thermal Barrier Coatings Produced By Electron Beam Physical Vapor Deposition,
2019
University of Texas at El Paso
Cmas/Volcanic Ash Infiltration Performance Of Yttria Rich-Zirconia Thermal Barrier Coatings Produced By Electron Beam Physical Vapor Deposition, Juan Jose Gomez Chavez
Open Access Theses & Dissertations
For many years the use of thermal barrier coatings (TBC) in gas turbine engines has allowed a significant increase in engine operating temperatures which are above the Ni-based super alloys' melting point. The base material for TBCs is the state of the art 7 wt % yttria stabilized zirconia (YSZ) which provides the thermal protection. Current industry demands for increased engine efficiency has pushed TBCs to the limits where significant technological constrains have been identified. One of the main ones represents the high temperature corrosion of the TBC material due to the ingestion of silicate based airborne particles commonly referred …
Tailoring The Mechanical And Optical Properties Of Silicon-Niobium-Nitride Composite Coatings,
2019
University of Texas at El Paso
Tailoring The Mechanical And Optical Properties Of Silicon-Niobium-Nitride Composite Coatings, Cristian Orozco
Open Access Theses & Dissertations
Nitride nanocomposite thin films have generated significant attention as a result of their robust mechanical properties, excellent triobology, and good chemical (corrosion) stability. Due to their excellent hardness and high wear resistance NbN coatings have found use in a wide variety of applications such as the coating of cutting tools and to strengthen the surface mechanical properties of superconducting cavities. The mechanical properties of NbN can be further improved through mixing with Si3N4, leading to the formation of a nanocomposite structure. NbN-Si3N4 nanocomposite coatings have been actively studied due to their high hardness, high elastic modulus, and high resistance to …
Exploration And Optimization Of Biomaterials And Cells Required For The Fabrication Of A "Cardiac Patch",
2019
University of Texas at El Paso
Exploration And Optimization Of Biomaterials And Cells Required For The Fabrication Of A "Cardiac Patch", Shweta Anil Kumar
Open Access Theses & Dissertations
Cardiac failure induced by myocardial infarction is believed to be one of the primary causes of morbidity and mortality all over the world. Affecting more than 26 million people worldwide, its prevalence has been observed to increase steadily. Myocardial infarction, which intitially begins as the occlusion of of a coronary artery, results in the death of millions of cardiomyocytes by obstructing blood flow to the serviced regions of the myocardium. The dead myocardium is replaced by a dense,collagenous scar which reduces the contractility of the heart, gradually leading to heart attacks. Most of the existing treatment therapies are palliative in …
Tailoring Physical Properties Of Shape Memory Polymers For Fdm-Type Additive Manufacturing,
2019
University of Texas at El Paso
Tailoring Physical Properties Of Shape Memory Polymers For Fdm-Type Additive Manufacturing, Paulina Aileen Quinonez
Open Access Theses & Dissertations
Shape memory polymers (SMPs) have found applicability in biomedical settings as well as other uses that can take advantage of objects that can change shape upon exposure to stimulus. Integrating polymers with shape memory characteristics into additive manufacturing technologies such as fused deposition modeling (FDMâ?¢) can increase the number of applications this manufacturing platform can be utilized. Currently, polyurethane and polylactic acid (PLA) are two FDMâ?¢-compatible materials that possess shape memory properties. On their own these materials do not have tunable shape memory properties, namely shape recovery and shape fixation. The work presented here entails the development and characterization of …
Resistance To Helium Bubble Formation In
Amorphous Sioc/Crystalline Fe Nanocomposite,
2019
University of Nebraska-Lincoln
Resistance To Helium Bubble Formation In Amorphous Sioc/Crystalline Fe Nanocomposite, Qing Su, Tianyao Wang, Jonathan Gigax, Lin Shao, Michael Nastasi
Department of Mechanical and Materials Engineering: Faculty Publications
The management of radiation defects and insoluble He atoms represent key challenges for structural materials in existing fission reactors and advanced reactor systems. To examine how crystalline/amorphous interface, together with the amorphous constituents affects radiation tolerance and He management, we studied helium bubble formation in helium ion implanted amorphous silicon oxycarbide (SiOC) and crystalline Fe composites by transmission electron microscopy (TEM). The SiOC/Fe composites were grown via magnetron sputtering with controlled length scale on a surface oxidized Si (100) substrate. These composites were subjected to 50 keV He+ implantation with ion doses chosen to produce a 5 at% peak He …
Wearable Devices For Single Cell Sensing And Transfection,
2019
Beihang University, Beijing
Wearable Devices For Single Cell Sensing And Transfection, Lingqian Chang, Yu-Chieh Wang, Faheem Ershad, Ruiguo Yang, Cunjiang Yu, Yubo Fan
Department of Mechanical and Materials Engineering: Faculty Publications
Transdermal drug delivery systems have been successful for decades. Now these devices can be further scaled down, and their applications have been extended to wide selections of cargo, ranging from natural molecules (e.g., insulin and glucose) to bioengineered molecules (e.g., nanoparticles and vaccines). Some emerging nanopatches show promise for precise single-cell gene transfection in vivo and have advantages over conventional tools in terms of delivery efficiency, safety, and controllability of delivered dose. In this review, we discuss recent technical advances in wearable micro/nano devices with unique capabilities or potential for single-cell biosensing and transfection in the skin or other organs, …
Segregation Of Mo Atoms Into Stacking Faults In Crfeconimo Alloy,
2019
University of Nebraska-Lincoln
Segregation Of Mo Atoms Into Stacking Faults In Crfeconimo Alloy, Kaisheng Ming, Xiaofang Bi, Jian Wang
Department of Mechanical and Materials Engineering: Faculty Publications
Solute segregation at dislocations can impede the motion of dislocations, strengthening materials. Here, we study the formation and role of solute segregation at dislocations in CrFeCoNiMo high-entropy alloys (HEAs) by high-angle annular dark-field scanning transmission electron microscopy imaging and mechanical testing both deformed and annealed samples. Mo atoms exhibit pronounced segregation into the planar-extended core of dislocations, i.e. stacking faults, causing the increase in the yield strength while the loss of the ductility. This work suggests that mechanical properties of HEAs can be tailored by alloying additional elements that are in favor of segregation into dislocations.
Optimization Of Protein-Protein Interaction Measurements For Drug Discovery Using Afm Force Spectroscopy,
2019
Michigan State University
Optimization Of Protein-Protein Interaction Measurements For Drug Discovery Using Afm Force Spectroscopy, Yongliang Yang, Bixi Zeng, Zhiyong Sun, Amir Monemianesfahani, Jing Hou, Nian-Dong Jiao, Lianqing Liu, Liangliang Chen, Marc D. Basson, Lixin Dong, Ruiguo Yang, Ning Xi
Department of Mechanical and Materials Engineering: Faculty Publications
Increasingly targeted in drug discovery, protein-protein interactions challenge current high throughput screening technologies in the pharmaceutical industry. Developing an effective and efficient method for screening small molecules or compounds is critical to accelerate the discovery of ligands for enzymes, receptors and other pharmaceutical targets. Here, we report developments of methods to increase the signal-to-noise ratio (SNR) for screening protein-protein interactions using atomic force microscopy (AFM) force spectroscopy. We have demonstrated the effectiveness of these developments on detecting the binding process between focal adhesion kinases (FAK) with protein kinase B (Akt1), which is a target for potential cancer drugs. These developments …
Local Control Robotic Surgical Devices And Related Methods,
2019
Ravenna, NE
Local Control Robotic Surgical Devices And Related Methods, Eric Markvicka, Tom Frederick, Jack Mondry, Joe Bartels, Shane Michael Farritor
Department of Mechanical and Materials Engineering: Faculty Publications
The various robotic medical devices include robotic devices that are disposed within a body cavity and positioned using a support component disposed through an orifice or opening in the body cavity. Additional embodiments relate to devices having arms coupled to a device body wherein the device has a minimal profile such that the device can be easily inserted through smaller incisions in comparison to other devices without such a small profile. Further embodiments relate to methods of operating the above devices.
Medical Inflation, Attachment And Delivery Devices And Related Methods,
2019
Boulder, CO
Medical Inflation, Attachment And Delivery Devices And Related Methods, Mark Rentschler, Shane Michael Farritor
Department of Mechanical and Materials Engineering: Faculty Publications
The various embodiments disclosed herein relate to procedural space maintenance devices, medical device positioning devices, and devices that provide both procedural space maintenance and device positioning. Further embodiments relate to medical device insertion and/or retraction devices.
Reliability Estimation Of Reciprocating Seals Based On Multivariate Dependence Analysis And It's Experimental Validation,
2019
Old Dominion University
Reliability Estimation Of Reciprocating Seals Based On Multivariate Dependence Analysis And It's Experimental Validation, Chao Zhang, Rentong Chen, Shaoping Wang, Yujie Qian, Mileta M. Tomovic
Engineering Technology Faculty Publications
Accurate reliability estimation for reciprocating seals is of great significance due to their wide use in numerous engineering applications. This work proposes a reliability estimation method for reciprocating seals based on multivariate dependence analysis of different performance indicators. Degradation behavior corresponding to each performance indicator is first described by the Wiener process. Dependence among different performance indicators is then captured using D-vine copula, and a weight-based copula selection method is utilized to determine the optimal bivariate copula for each dependence relationship. A two-stage Bayesian method is used to estimate the parameters in the proposed model. Finally, a reciprocating seal degradation …
Fe Modeling Methodology For Load Analysis And Preliminary Sizing Of Aircraft Wing Structure,
2019
Defense Acquisition Program Administration
Fe Modeling Methodology For Load Analysis And Preliminary Sizing Of Aircraft Wing Structure, Jun Hwan Jang, Sang Ho Ahn
International Journal of Aviation, Aeronautics, and Aerospace
It is a critical part at the basic design phase of aircraft structural design to build a finite element model and it will have a direct impact on time and cost for airframe structure development. In addition, the objective of finite element model will be varied depending on each design review phase and the modelling methodology varied accordingly. In order to build an effective and economic finite element model, it is required to develop adequate level of modelling methodology based on each design phase and its objectives. Therefore, in this paper, the finite element modeling methodology was presented for internal …
