Robotics Commons^™

Certification Basis For A Fully Autonomous Uncrewed Passenger Carrying Urban Air Mobility Aircraft, Steve Price

Student Works

The Urban Air Mobility campaign has set a goal to efficiently transport passengers and cargo in urban areas of operation with autonomous aircraft. This concept of operations will require aircraft to utilize technology that currently does not have clear regulatory requirements. This report contains a comprehensive analysis and creation of a certification basis for a fully autonomous uncrewed passenger carrying rotorcraft for use in Urban Air Mobility certified under Title 14 Code of Federal Regulations Part 27. Part 27 was first analyzed to determine the applicability of current regulations. The fully electric propulsion system and fully autonomous flight control system …

Assessment Of Simulated And Real-World Autonomy Performance With Small-Scale Unmanned Ground Vehicles, William Peyton Johnson

Theses and Dissertations

Off-road autonomy is a challenging topic that requires robust systems to both understand and navigate complex environments. While on-road autonomy has seen a major expansion in recent years in the consumer space, off-road systems are mostly relegated to niche applications. However, these applications can provide safety and navigation to dangerous areas that are the most suited for autonomy tasks. Traversability analysis is at the core of many of the algorithms employed in these topics. In this thesis, a Clearpath Robotics Jackal vehicle is equipped with a 3D Ouster laser scanner to define and traverse off-road environments. The Mississippi State University …

Actively Guided Cansats For Assisting Localization And Mapping In Unstructured And Unknown Environments, Cary Chun, M. Hassan Tanveer

Symposium of Student Scholars

When navigating in unknown and unstructured environments, Unmanned Arial Vehicles (UAVs) can struggle when attempting to preform Simultaneous Localization and Mapping (SLAM) operations. Particularly challenging circumstance arise when an UAV may need to land or otherwise navigate through treacherous environments. As the primary UAV may be too large and unwieldly to safely investigate in these types of situations, this research effort proposes the use of actively guided CanSats for assisting in localization and mapping of unstructured environments. A complex UAV could carry multiple of these SLAM capable CanSats, and when additional mapping and localization capabilities where required, the CanSat would …

Unmanned Aerial System Design For Civil Engineering Operations – A Vip Study, Ezra Robles, Harrison Vicknair, Derek Price, Logan Westra, George Pitcock, Joshua Diamond, Bhuvan Saraswat, Jeremiah Prayor, Fon Saliki

Symposium of Student Scholars

Unmanned Aerial System Design for Civil Engineering Operations – A Case Study

The objective of the project is to design and build a modular Unmanned Aerial System (UAS) that meets the specifications set forth by United Consulting – a local civil engineering company. These specifications are achieved through three unique missions. In each mission, data is collected using different methods. These missions include land surveying, bridge structure inspection and manhole probing. The key requirements of the drone are to maintain a minimum flight time of 30 minutes and the ability to receive and transmit telemetry, photographic and video data from …

Panodepth – Panoramic Monocular Depth Perception Model And Framework, Adley K. Wong

Master's Theses

Depth perception has become a heavily researched area as companies and researchers are striving towards the development of self-driving cars. Self-driving cars rely on perceiving the surrounding area, which heavily depends on technology capable of providing the system with depth perception capabilities. In this paper, we explore developing a single camera (monocular) depth prediction model that is trained on panoramic depth images. Our model makes novel use of transfer learning efficient encoder models, pre-training on a larger dataset of flat depth images, and optimizing the model for use with a Jetson Nano. Additionally, we present a training and optimization framework …

Intelligent Autonomous Inspections Using Deep Learning And Detection Markers, Alejandro Martinez Acosta

Open Access Theses & Dissertations

Inspection of industrial and scientific facilities is a crucial task that must be performed regularly. These inspections tasks ensure that the facilityâ??s structure is in safe operational conditions for humans. Furthermore,the safe operation of industrial machinery, is dependent on the conditions of the environment. For safety reasons, inspections for both structural integrity and equipment is often manually performed by operators or technicians. Naturally, this is often a tedious and laborious task. Additionally, buildings and structures frequently contain hard to reach or dangerous areas, which leads to the harm, injury or death of humans. Autonomous robotic systems offer an attractive solution …

Productivity And Quality Evaluation In Assembly Using Collaborative Robots, Carlos F. Manzanares Vega

Open Access Theses & Dissertations

In Industry 4.0, various technologies have been applied to achieve automation for traditional manufacturing and practices. For this reason, Smart Manufacturing (SM) environments utilize collaborative robots for process optimization by integrating the Internet of Things (IoT). Cobots are equipped with sensors and/or other devices to be able to transmit data in real-time while performing their tasks. Consequently, such SM implementations improves the decision making and business development, such as supply chain and operations, by sharing real-time data from a plant operational level. The collaborative robots are also designed to safely interact and collaborate with humans to perform tasks and optimize …

Design Of Environment Aware Planning Heuristics For Complex Navigation Objectives, Carter D. Bailey

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

A heuristic is the simplified approximations that helps guide a planner in deducing the best way to move forward. Heuristics are valued in many modern AI algorithms and decision-making architectures due to their ability to drastically reduce computation time. Particularly in robotics, path planning heuristics are widely leveraged to aid in navigation and exploration. As the robotic platform explores and navigates, information about the world can and should be used to augment and update the heuristic to guide solutions. Complex heuristics that can account for environmental factors, robot capabilities, and desired actions provide optimal results with little wasted exploration, but …

Modeling, Control And Estimation Of Reconfigurable Cable Driven Parallel Robots, Adhiti Raman Thothathri

All Dissertations

The motivation for this thesis was to develop a cable-driven parallel robot (CDPR) as part of a two-part robotic device for concrete 3D printing. This research addresses specific research questions in this domain, chiefly, to present advantages offered by the addition of kinematic redundancies to CDPRs. Due to the natural actuation redundancy present in a fully constrained CDPR, the addition of internal mobility offers complex challenges in modeling and control that are not often encountered in literature.

This work presents a systematic analysis of modeling such kinematic redundancies through the application of reciprocal screw theory (RST) and Lie algebra while …

A Mechanically Intelligent Hosing-Drone, Blake Hament

UNLV Theses, Dissertations, Professional Papers, and Capstones

This manuscript presents a ”mechanically intelligent” approach to designing a Hosing-Drone for heavy-duty pressure washing. Spraying a hose creates strong reaction forces and torques. Previously demonstrated spraying robots are over-engineered to be very massive with huge inertias. These high inertias ”wash out” the reaction from the spraying. In the proposed approach, the contributions from all observable fluid dynamics, fluid structure interactions, and aerodynamics are studied individually and for the coupled system. Experimental data is collected and fit to dynamic models. These models are used to design a smaller, lighter, more agile vehicle than has been previously demonstrated. An impedance controller …

Material Characterization And Comparison Of Sol-Gel Deposited And Rf Magnetron Deposited Lead Zirconate Titanate Thin Films, Katherine Lynne Miles

Mechanical Engineering ETDs

Lead zirconate titanate (PZT) has been a material of interest for sensor, actuator, and transducer applications in microelectromechanical systems (MEMS). This is due to their favorable piezoelectric, pyroelectric and ferroelectric properties. While various methods are available to deposit PZT thin films, radio frequency (RF) magnetron sputtering was selected to provide high quality PZT films with the added capability of batch processing. These sputter deposited PZT films were characterized to determine their internal film stress, Young’s modulus, composition, and structure. After characterization, the sputtered PZT samples were poled using corona poling and direct poling methods. As a means of comparison, commercially …

A Machine Learning Approach To Robotic Additive Manufacturing Of Uv-Curable Polymers Using Direct Ink Writing, Luis A. Velazquez

LSU Master's Theses

This thesis presents the design and implementation of a robotic additive manufacturing system that uses ultraviolet (UV)-curable thermoset polymers. Its design considers future applications involving free-standing 3D printing by means of partial UV curing and the fabrication of samples that are reinforced with fillers or fibers to manufacture complex-shape objects.

The proposed setup integrates a custom-built extruder with a UR5e collaborative manipulator. The capabilities of the system were demonstrated using Anycubic resin formulations containing fumed silica (FS) at varying weight fractions from 2.8 to 8 wt%. To fully cure the specimens after fabrication, a UV chamber was used. Then, measurements …

Enabling The Human Perception Of A Working Camera In Web Conferences Via Its Movement, Anish Shrestha

LSU Master's Theses

In recent years, video conferencing has seen a significant increase in its usage due to the COVID-19 pandemic. When casting user’s video to other participants, the videoconference applications (e.g. Zoom, FaceTime, Skype, etc.) mainly leverage 1) webcam’s LED-light indicator, 2) user’s video feedback in the software and 3) the software’s video on/off icons to remind the user whether the camera is being used. However, these methods all impose the responsibility on the user itself to check the camera status, and there have been numerous cases reported when users expose their privacy inadvertently due to not realizing that their camera is …

Event-Triggered Optimal Adaptive Control Of Partially Unknown Linear Continuous-Time Systems With State Delay, Rohollah Moghadam, Vignesh Narayanan, Sarangapani Jagannathan

Publications

This paper proposes an event-triggered optimal adaptive output feedback control design approach by utilizing integral reinforcement learning (IRL) for linear time-invariant systems with state delay and uncertain internal dynamics. In the proposed approach, the general optimal control problem is formulated into the game-theoretic framework by treating the event-triggering threshold and the optimal control policy as players. A cost function is defined and a value functional, which includes the delayed system output, is considered. First, by using the value functional and applying stationarity conditions using the Hamiltonian function, the output game delay algebraic Riccati equation (OGDARE) and optimal control policy are …

Multi-Robot Symbolic Task And Motion Planning Leveraging Human Trust Models: Theory And Applications, Huanfei Zheng

All Dissertations

Multi-robot systems (MRS) can accomplish more complex tasks with two or more robots and have produced a broad set of applications. The presence of a human operator in an MRS can guarantee the safety of the task performing, but the human operators can be subject to heavier stress and cognitive workload in collaboration with the MRS than the single robot. It is significant for the MRS to have the provable correct task and motion planning solution for a complex task. That can reduce the human workload during supervising the task and improve the reliability of human-MRS collaboration. This dissertation relies …

Device Free Indoor Localization Of Human Target Using Wifi Fingerprinting, Prasanga Neupane

LSU Master's Theses

Indoor localization of human objects has many important applications nowadays. Proposed here is a new device free approach where all the transceiver devices are fixed in an indoor environment so that the human target doesn't need to carry any transceiver device with them. This work proposes radio-frequency fingerprinting for the localization of human targets which makes this even more convenient as radio-frequency wireless signals can be easily acquired using an existing wireless network in an indoor environment. This work explores different avenues for optimal and effective placement of transmitter devices for better localization. In this work, an experimental environment is …

A Comparison Of Robotic Hand Thumb Designs, Ryon Miro

Journal of the South Carolina Academy of Science

No abstract provided.

Adaptive Multi-Scale Place Cell Representations And Replay For Spatial Navigation And Learning In Autonomous Robots, Pablo Scleidorovich

USF Tampa Graduate Theses and Dissertations

Place cells are one of the most widely studied neurons thought to play a vital role in spatial cognition. Extensive studies show that their activity in the rodent hippocampus is highly correlated with the animal’s spatial location, forming “place fields” of smaller sizes near the dorsal pole and larger sizes near the ventral pole. Despite advances, it is yet unclear how this multi-scale representation enables navigation in complex environments.

In this dissertation, we analyze the place cell representation from a computational point of view, evaluating how multi-scale place fields impact navigation in large and cluttered environments. The objectives are to …

Columnas: The Honors Program Newsletter At Bentley University, Debayan Sen, Hailey Jennato, Gabe Holmes, Daniel Furze

Honors Program

Page 1: SOCIAL MEDIA—A VEHICLE FOR SOCIAL CHANGE OR VIRTUE SIGNALING? ~ By Debayan Sen ’23

Page 2: WILL ARTIFICIAL INTELLIGENCE AND ROBOTICS REPLACE THE HUMAN WORKER? ~ By Hailey Jennato ’24

Page 3: HOW TO HEALTHILY COMMUNICATE IN A RELATIONSHIP: NO, NOT JUST A ROMANTIC ONE ~ By Gabe Holmes ’26

Page 4: THE W SLANT ~ By Daniel Furze ’26

Development And Evaluation Of A Hand Exoskeleton For Neurorehabilitation Post Stroke, Ashley Joyce Mont

Dissertations

Stroke affects approximately 800,000 people in the United States each year, and due to its chronic effects, it is one of the leading causes of disability. Many individuals with stroke suffer the loss of motor function in their paretic upper extremity, and longitudinal studies show that 30 — 66% of individuals with hemiplegia fail to regain arm function six months post stroke. After a stroke, the brain undergoes neuroplasticity which will promote recovery of function. Investigators and clinicians are trying to develop rehabilitation interventions that can be designed to promote neuroplasticity, enhancing the recovery outcomes of therapy.

For individuals with …