Environmental Engineering Commons^™

An Experimental Investigation Of The Optimum Properties And Conditions For Use Of Anionic Emulsions In Road Maintenance Applications, Simonas Ignatavicius, Alan Kavanagh, David Colleran, Michael J. Brennan, Shane Newell

Civil Engineering Research in Ireland 2020

Bitumen emulsions are used for a range of road maintenance applications, including surface dressing, gravel seals, slurry seals, tack coating, cold-mix asphalt and in situ pavement recycling. The emulsions used can be classified as being either cationic (i.e. possessing a positive electrostatic surface charge) or anionic (i.e. carrying a negative electrostatic surface charge). The vast majority of emulsions used for such applications in Europe are cationic, while anionic bitumen emulsions are used widely throughout North America and Africa. The aims of the experimental study described in this paper were (a) to investigate why one or the other emulsion type is …

An Analysis Of The Effectiveness Of Bitumen Additives On The Performance Of Pavement Surface Dressings, Alan Anderson, John Casserly, Alan Kavanagh, Jim Campbell

Civil Engineering Research in Ireland 2020

Surface dressing is a maintenance technique that uses thin layers of bitumen emulsion and single sized aggregates. The surface dressing process seals and binds the surface of a road to protect its substructure from water ingress. It also provides increased skid resistance, which improves safety for road users. Early life chip-loss can occur if there is an insufficient degree of adhesion between the emulsion and aggregate used. The range of additives used in bitumen can have an effect on their adhesion properties. The focus of this research project was to investigate if the use of these additives in surface dressing …

An Experimental Investigation Of The Optimum Properties And Conditions For Use Of Anionic Emulsions In Road Maintenance Applications, Simonas Ignatavicius, Alan Kavanagh, David Colleran, Michael J. Brennan, Shane Newell

Civil Engineering Research in Ireland 2020

Bitumen emulsions are used for a range of road maintenance applications, including surface dressing, gravel seals, slurry seals, tack coating, cold-mix asphalt and in situ pavement recycling. The emulsions used can be classified as being either cationic (i.e. possessing a positive electrostatic surface charge) or anionic (i.e. carrying a negative electrostatic surface charge). The vast majority of emulsions used for such applications in Europe are cationic, while anionic bitumen emulsions are used widely throughout North America and Africa. The aims of the experimental study described in this paper were (a) to investigate why one or the other emulsion type is …

Analysis And Optimisation Of Tii’S Pams Reset Values And Deterioration Models For Irish Pavement Conditions, James Quinn, Raymond Mcgowan, Tomas O'Flaherty

Civil Engineering Research in Ireland 2020

Ireland has a national road network of approximately 5300km that is managed by Transport Infrastructure Ireland (TII). TII create yearly pavement maintenance and renewal programs from the operation of a Pavement Asset Management System (PAMS). Accurate pavement deterioration models and reset values are an essential part of PAMS and are required for life cycle cost analysis (LCCA). Pavement maintenance and renewal schemes are prioritised based on the LCCA's largest benefit to cost ratio, and therefore optimise the annual pavement maintenance and renewal budget. Currently, TII implement pavement deterioration models and reset values from Austria's and Belgium's PAMS, and are not …

An Analysis Of The Effectiveness Of Bitumen Additives On The Performance Of Pavement Surface Dressings, Alan Anderson, John Casserly, Alan Kavanagh, Jim Campbell

Civil Engineering Research in Ireland 2020

Surface dressing is a maintenance technique that uses thin layers of bitumen emulsion and single sized aggregates. The surface dressing process seals and binds the surface of a road to protect its substructure from water ingress. It also provides increased skid resistance, which improves safety for road users. Early life chip-loss can occur if there is an insufficient degree of adhesion between the emulsion and aggregate used. The range of additives used in bitumen can have an effect on their adhesion properties. The focus of this research project was to investigate if the use of these additives in surface dressing …

Towards Automated Uav Assisted Bridge Inspections Using Photogrammetry And Image Processing Techniques, Habeene Habeenzu, Patrick Mcgetrick, David Hester, Su Taylor, Louie Wong

Civil Engineering Research in Ireland 2020

At the heart of addressing bridge condition challenges are bridge inspections. The main activity during a bridge inspection is close, arm’s length visual inspection of the entire bridge structure. During this process, all defects such as cracks, spalls and material degradation are manually recorded on the bridge itself and on inspection forms. Where access is difficult such as where a safe working platform cannot be mounted under bridge decks, or on high bridges, expensive underbridge equipment is required which when used results in expensive lane closures. Furthermore, visual inspections have been shown to lack consistency from inspector to inspector and …

Acceleration Based Bridge Weigh In Motion Using Moving Force, Shou Wang, Daniel Mccrum, Eugene O'Brien

Civil Engineering Research in Ireland 2020

Measuring vehicle axles weights is an important method to control traffic and monitor infrastructure. Traditional methods of measuring the static weight of vehicles at a weigh station is disruptive and time consuming. It is more cost effective and efficient to indirectly measure moving vehicle weights crossing a bridge. The weigh-in-motion concept, first proposed by Moses (1979) is an algorithm that uses measured bridge structural response (deflection, strain, …) due to passing vehicles to and a theoretical response. Moving Force identification (MFI) is a variation of the dynamic WIM algorithm that gives a force time history as a vehicle passes the …

Wind Power Prediction And Early Downtime Detection For Ireland, Vikram Pakrashi, Basuraj Bhowmik, Juan Manuel González-Sopeña, Paul Mucchielli, Bidisha Ghosh

Civil Engineering Research in Ireland 2020

Wind energy must be commercially competitive to be economically sustainable. Existing wind farms in Ireland must be more efficient to meet the 2009 EU Renewable Energy Directive target of 7% of total energy demand from onshore wind energy farms, which is 45% of the total national renewable energy target of 16%. WindPearl - a Sustainable EnergyAuthority of Ireland (SEAI) funded project is currently looking into improvin operations & maintenance (O&M) of onshore wind turbine farms in Ireland.

Application Of The Iec Technical Specification For Assessment Of Wave Energy Resource: A Case Study From The West Coast Of Ireland, Iulia Anton, Stephen Nash

Civil Engineering Research in Ireland 2020

There is significant interest globally in harnessing our ocean wave energy resource, estimated at approximately 30,000 TWh/year. The key to this is understanding the resource. The International Electrotechnical Commission (IEC) has developed a technical specification for the evaluation of wave energy resource, IEC-TS 62600- 101: Wave energy resource assessment and characterization. This research applies the IEC standard for a resource characterization study of the Atlantic Marine Energy Test Site on the west coast of Ireland. A key focus is the comparison of the detailed IEC validation approach using scatter diagrams with the traditional timeseries validation approach. Coarse (0.005°) and fine …

A Review Of Vision Based Methods For Pothole Detection And Road Profile Analysis, Darragh Lydon, Su Taylor, Myra Lydon, Julia Early

Civil Engineering Research in Ireland 2020

This paper is an overview of the development and application of Computer Vision for the detection of pothole, pavement distress and road profile analysis and categorisation. A brief explanation of the traditional methods for determining these factors is given, followed by a chronological description of the evolution and the challenges of using Computer Vision (CV) approaches to determine these conditions. The paper is separated into sections aligned to image capture and analysis methodologies. Qualitative evaluations and comparison of these methods have been provided along with the proposal of guidelines for new computer vision-based road analysis systems.

Analysis And Optimisation Of Tii’S Pams Reset Values And Deterioration Models For Irish Pavement Conditions, James Quinn, Raymond Mcgowan, Tomas O'Flaherty

Civil Engineering Research in Ireland 2020

Ireland has a national road network of approximately 5300km that is managed by Transport Infrastructure Ireland (TII). TII create yearly pavement maintenance and renewal programs from the operation of a Pavement Asset Management System (PAMS). Accurate pavement deterioration models and reset values are an essential part of PAMS and are required for life cycle cost analysis (LCCA). Pavement maintenance and renewal schemes are prioritised based on the LCCA's largest benefit to cost ratio, and therefore optimise the annual pavement maintenance and renewal budget. Currently, TII implement pavement deterioration models and reset values from Austria's and Belgium's PAMS, and are not …

Winter Maintenance On The Irish Road Network, Hugh Mcconnell, Brian Mccann

Civil Engineering Research in Ireland 2020

Winter maintenance relates to those activities undertaken where the objective is to minimise the impact of frost, ice or snow on the travelling public. The responsibility for winter maintenance of all roads in Ireland currently rests with local authorities and Transport Infrastructure Ireland (TII) (Formerly the NRA) on behalf of the Department of Transport, Tourism and Sport (DTTaS), (DTTaS, 2017). The aim of the study was to examine current winter maintenance practices undertaken in Ireland by local authorities and the Motorway Maintenance and Renewals Contracts (MMaRC) contractors and examine the potential financial, operational and environmental benefits if pre-wet and brine …

A Review Of Vision Based Methods For Pothole Detection And Road Profile Analysis, Darragh Lydon, S. E. Taylor, Myra Lydon, Julia Early

Civil Engineering Research in Ireland 2020

This paper is an overview of the development and application of Computer Vision for the detection of pothole, pavement distress and road profile analysis and categorisation. A brief explanation of the traditional methods for determining these factors is given, followed by a chronological description of the evolution and the challenges of using Computer Vision (CV) approaches to determine these conditions. The paper is separated into sections aligned to image capture and analysis methodologies. Qualitative evaluations and comparison of these methods have been provided along with the proposal of guidelines for new computer vision-based road analysis systems.

Winter Maintenance On The Irish Road Network, Hugh Mcconnell, Brian Mccann

Civil Engineering Research in Ireland 2020

Winter maintenance relates to those activities undertaken where the objective is to minimise the impact of frost, ice or snow on the travelling public. The responsibility for winter maintenance of all roads in Ireland currently rests with local authorities and Transport Infrastructure Ireland (TII) (Formerly the NRA) on behalf of the Department of Transport, Tourism and Sport (DTTaS), (DTTaS, 2017). The aim of the study was to examine current winter maintenance practices undertaken in Ireland by local authorities and the Motorway Maintenance and Renewals Contracts (MMaRC) contractors and examine the potential financial, operational and environmental benefits if pre-wet and brine …

Modelling The Thermal Behaviour Of A Precast Pcm Enhanced Concrete Cladding Panel, Dervilla Niall, Roger P. West, Oliver Kinnane, Richard Hegarty

Civil Engineering Research in Ireland 2020

According to the World Business Council for Sustainable Development there is currently a stock of more than 80 million buildings in Europe built between 1950 and 1975, a period during which energy performance was not considered in building design. To enable governments to comply with the European Directive 2010/31/EU on the energy performance of buildings, strategies are required to improve the energy efficiency of these buildings. Using the mass of a building to store or dissipate heat can reduce the demand on the auxiliary heating and/or cooling systems and hence reduce the overall energy demand of the building.

Previous research …

Analysis And Design Of A Novel Heavy-Duty Precast Element, Daniel Naughton, Michael Naughton, Michael O'Sullivan, Suhaib Salawdeh

Civil Engineering Research in Ireland 2020

Window sills are common to most buildings. In Ireland, concrete is the most popular material used for external sills. A standard one-metre concrete window sill weighs about 70kg. While external window sills are required to have sufficient capacity to resist damage during transportation and loading, they are non-structural elements. Therefore, there is no need for their high selfweight. This project looks to redesign concrete window sills to make them lighter. Decreasing the amount of concrete used in each sill would significantly reduce their self-weight. This would make concrete window sills more manageable in terms of transportation and installation. Two design …

Development And Localisation Of Ultra High Performance Concrete Using A Particle Packing Model, William Wilson, Tomas O'Flaherty

Civil Engineering Research in Ireland 2020

Ultra-high performance fibre reinforced concrete (UHPFRC) is used worldwide to improve the structural performance of infrastructure such as bridges, extend their working life and reduce environmental impact. As a result thinner structures are constructed leading to reductions in the structure’s self-weight and the volume of concrete and natural raw aggregates used in their construction. A drawback to UHPFRC is that it results in a significant rise in initial costs over normal and even high performance concretes, and it has very high binder contents, which in some cases is greater than 1100kg/m³. Therefore, the cost-efficiency and sustainability of this …

Composite Behaviour Of Wide Sandwich Panels With High Performance Concrete Thin Wythes With And Without Thermomass Shear Connectors, Jagoda Lipczynska, Roger P. West, Michael Grimes, Dervilla Niall, Oliver Kinnane, Richard Hegarty

Civil Engineering Research in Ireland 2020

To partly address the future sustainability of energy use in buildings, there is a program in Europe to retrofit domestic and commercial buildings with non-load bearing insulated re-cladding and over-cladding panels. Recent research work has shown that limited composite action is possible depending on the type of non-conductive shear connector and the stiffness of the insulation between the inner and outer wythes. This paper reports on the mix design development to develop high strength 20mm thick wythes and the manufacture of sandwich panels with five silicone-bonded layers of XPS insulation, making up a panel which is 220mm thick. These model …

Optimization Of Nitrate Removal From Aqueous Solution By Acid-Activated Rice Straw Supported Nano Zero-Valent Iron Using Response Surface Methodology, Dalia A. Ali Eng, Nagwa Mahmoud Al-Mansi Prof, Mohamed Amin Sadek Prof., Ahmad Wafiq Abolnasr Dr.

Chemical Engineering

Rice straw is one of the most common agricultural wastes due to its large production amounts. Energy valorization of rice straw is a technology used for nitrate removal as the produced ashes used to generate the adsorbent by means of an alkali dissolution followed by acid precipitation. The novelty of the proposed process is that the production of the nano zero-valent iron supported acid-activated rice straw (AARS-nZVI) adsorbent is carried out without the energy valorization process but, through an acid activation for rice straw followed by precipitation of nZVI particles on its surface. The new adsorbent synthesis, characterization and application …

Advanced Materials For Air Pollutants Removal In A Combustion System, Sungyoon Jung

McKelvey School of Engineering Graduate Student Theses & Dissertations

Air pollutants directly or indirectly impact human health and the environment. Large quantities of CO2, volatile organic compounds (VOCs), and particulate matter are emitted from combustion systems, and cause climate change, smog formation, and pose serious health risks. The increasing demand for the remediation of air pollutants at the source has drawn much attention to the use of advanced materials due to their high reactivities and special properties. In order to achieve the successful application of advanced materials for the remediation of problematic emissions, three aspects, (1) synthesis method, (2) characterization of materials’ structural properties, and (3) evaluation of materials’ …