Improving Surveying Accuracy And Efficiency In Connecticut: An Accuracy Assessment Of Geoid03 And Geoid09,
2010
University of Connecticut
Improving Surveying Accuracy And Efficiency In Connecticut: An Accuracy Assessment Of Geoid03 And Geoid09, Thomas H. Meyer, Robert Baron
Department of Natural Resources and the Environment Articles
Comparing published NAVD 88 Helmert orthometric heights of First-Order bench marks against GPS-determined orthometric heights showed that GEOID03 and GEOID09 perform at their reported accuracy in Connecticut. GPS-determined orthometric heights were determined by subtracting geoid undulations from ellipsoid heights obtained from a network least-squares adjustment of GPS occupations in 2007 and 2008. A total of 73 markers were occupied in these stability classes: 25 class A, 11 class B, 12 class C, 2 class D bench marks, and 23 temporary marks with transferred elevations. Adjusted ellipsoid heights were compared against OPUS as a check. We found that: the GPS-determined orthometric …
A Life Cycle Cost Analysis Of Large-Scale Thermal Energy Storage Technologies For Buildings Using Combined Heat And Power,
2010
Technological University Dublin
A Life Cycle Cost Analysis Of Large-Scale Thermal Energy Storage Technologies For Buildings Using Combined Heat And Power, Kenneth Gaine, Aidan Duffy
Conference Papers
Buildings account for approximately 40% of energy consumption and greenhouse gas (GHG) emissions in developed economies, of which approximately 55% of building energy is used for heating and cooling. The reduction of building-related GHG emissions is a high international policy priority. For this reason and because there are many technical solutions for this, these polices should involve significant improvements in the uptake of small-scale energy efficient (EE) systems. However the widespread deployment of many technologies, must overcome a number of barriers, one of which is a temporal (diurnal or seasonal) mismatch between supply and demand. Costeffective thermal storage solutions have …
Bs News July/August,
2010
Technological University Dublin
Best Practices For Dealing With Price Volatility In Utah's Residential Construction Market,
2010
Brigham Young University - Provo
Best Practices For Dealing With Price Volatility In Utah's Residential Construction Market, James Packer Smith
Theses and Dissertations
Price volatility is a consistent problem that affects all of the parties involved in the residential construction industry. The myriad factors that can have an impact on construction costs are such that it is extremely hard to anticipate upcoming changes in a timely and accurate way. When prices fluctuate during the course of a project, estimates become erroneous and completion of projects within expected budgets becomes difficult. Increasing prices typically leave contractors with the majority of the risk burden due to the enforceability of contracts that are likely to have been executed months prior. The risk associated with the owner's …
Best Practices For Dealing With Price Volatility In Utah Commercial Construction,
2010
Brigham Young University - Provo
Best Practices For Dealing With Price Volatility In Utah Commercial Construction, Justin Earl Weidman
Theses and Dissertations
In the commercial construction industry, the problem of price volatility as it pertains to materials and labor is a consistent problem. The changing instability of market conditions presents a challenge for construction companies to accurately estimate and complete projects within budget. This volatility can lead to higher costs and more risk to suppliers, contractors, and owners which can cause financial distress for all parties involved in the construction process. As lump sum contracts are typically being used on many projects, the owners seem to have the upper hand and are forcing contractors to honor lump sum contracts even when prices …
Natural Fibers And Fiberglass: A Technical And Economic Comparison,
2010
Brigham Young University - Provo
Natural Fibers And Fiberglass: A Technical And Economic Comparison, Justin Andrew Zsiros
Theses and Dissertations
Natural fibers have received attention in recent years because of their minimal environmental impact, reasonably good properties, and low cost. There is a wide variety of natural fibers suitable for composite applications, the most common of which is flax. Flax has advantages in tensile strength, light weight, and low cost over other natural fibers. As with other natural and synthetic fibers, flax is used to reinforce both thermoset and thermoplastic matrices. When flax is used in thermoplastic matrices, polypropylene and polyethylene are the main resins used. Although at first glance flax may seem to be a cheaper alternative to fiberglass, …
The Relevance Of Teaching Traditional Measurement Techniques To Undergraduate Quantity Surveying Students.,
2010
Technological University Dublin
The Relevance Of Teaching Traditional Measurement Techniques To Undergraduate Quantity Surveying Students., Fiacra P. Mcdonnell
Articles
Measurement of quantities is a core skill which must be inherent in all graduates from Quantity Surveying courses. Many students find this subject difficult to grasp, and the learning experience can be problematic especially in the first semester of first year. This is not unique to measurement as in many cases first year students are in the process of adapting to a new stage in their life, along with attempting to master many new subjects (Cottrell, 2008). This is reinforced by Johnston (2010) who highlights the many challenges being experienced by first year students and observes that “ entering first …
Table 6.04,
2010
Purdue University
Table 6.04, Mark E. Shaurette
Supplementary Content for <em>Demolition: Practices, Technology, and Management</em> <br>(ISBN 978-1-55753-567-2)
No abstract provided.
Table 6.03,
2010
Purdue University
Table 6.03, Mark E. Shaurette
Supplementary Content for <em>Demolition: Practices, Technology, and Management</em> <br>(ISBN 978-1-55753-567-2)
No abstract provided.
Affordable Lightweight High Performance Concrete (Alwhpc): Expanding The Envelope Of Concrete Mix Design,
2010
University of Nebraska-Lincoln
Affordable Lightweight High Performance Concrete (Alwhpc): Expanding The Envelope Of Concrete Mix Design, Kevin J. Simons
Department of Construction Engineering and Management: Dissertations, Theses, and Student Research
One way to reduce excess material would be to lighten the load on a structure with the use of affordable lightweight high performance concrete (ALWHPC). Most or all lightweight high performance concrete mixes used today include lightweight aggregates as the coarse aggregate and sand for the fine aggregate. ALWHPC mix designs contain all lightweight aggregates and cementitious materials that are readily available throughout the United States. Instead of 115 – 120 pcf, ALWHPC mix designs range from 88 – 100 pcf and strengths from 2,700 – 8,700 psi compressive strength. This research will explore the use of local lightweight aggregates …
Bs News May/June,
2010
Technological University Dublin
An Exploratory Study On Energy Consumption Of Energy Star And Non-Energy Star Homes,
2010
University of Nevada Las Vegas
An Exploratory Study On Energy Consumption Of Energy Star And Non-Energy Star Homes, Prajakta Kulkarni
UNLV Theses, Dissertations, Professional Papers, and Capstones
The reduction of energy consumption is one of the economic necessities in the United States due to depleting energy sources in the world. The construction industry is stepping forward to reduce the energy consumption of buildings by efficient designs or by constructing buildings with energy efficient materials and features. In 1992, the U.S. Environmental Protection Agency (EPA) and Department of Energy (DOE) introduced the Energy Star Program to promote energy efficient products with the same or improved services. According to the EPA, Energy Star homes, which use these products, will consume 20 to 30 percent less energy than non-Energy Star …
Performance Of Nevada’S Aggregates In Alkali-Aggregate Reactivity Of Portland Cement Concrete,
2010
University of Nevada Las Vegas
Performance Of Nevada’S Aggregates In Alkali-Aggregate Reactivity Of Portland Cement Concrete, Mohammad Shahidul Islam
UNLV Theses, Dissertations, Professional Papers, and Capstones
Alkali-aggregate reaction (AAR) is a form of distress that occurs in concrete and results in serviceability problems, cracks, spalling, and other deterioration mechanisms. There are two categories of AAR, namely, alkali-silica reaction (ASR) and alkali-carbonate reaction (ACR). Alkali-silica reaction is one of the most recognized deleterious phenomena in concrete, and has been a major concern since its discovery in the 1940s. The reaction which occurs between reactive silica or silicates present in some aggregates and alkalis of Portland cement produces an alkali-silica gel that expands in the presence of moisture resulting in concrete cracks. ACR is also a chemical reaction …
Site Design Of A Four-Story 11,705 Sq-Ft Class A Office Building,
2010
Western Michigan University
Site Design Of A Four-Story 11,705 Sq-Ft Class A Office Building, Britney Richmond, Allison Porrett, Kimberly Warners
Honors Theses
This senior capstone design project was a two-semester long venture that began last fall with the formation of the team, the selection of the sponsored project, and the conclusion of a proposal. The purpose of the proposal was for the senior design team to display a thorough understanding of the project's scope of work and to declare the deliverables agreed upon by the team. The team began contact with the sponsor, Hurley &Stewart, prior to beginning the proposal writing in order to gain more details about the project at hand and to ask any questions. The team chose to add …
Input-Output Analysis Of Irish Construction Sector Greenhouse Gas Emissions,
2010
Technological University Dublin
Input-Output Analysis Of Irish Construction Sector Greenhouse Gas Emissions, Adolf Acquaye, Aidan Duffy
Articles
Ireland is committed to limiting its greenhouse gas (GHG) emissions to 113% of 1990 levels over the period 2008-12 and to 84% of 2005 levels by 2020 under the Kyoto Agreement and the EU’s ’20 20’ by 2020 respectively. National policies have targeted many industry sectors but have failed to directly tackle GHG emissions associated with construction activity. This paper estimates energy and GHG emissions intensities of the Irish construction sector and subsectors and estimates its contribution to Irish national emissions. This information is used to identify and assess the impacts of policy measures which would result in a reduction …
Processing A Nickel Nanostrand And Nickel Coated Carbon Fiber Filled Conductive Polyethylene By Injection Molding,
2010
Brigham Young University - Provo
Processing A Nickel Nanostrand And Nickel Coated Carbon Fiber Filled Conductive Polyethylene By Injection Molding, David Anthony Whitworth
Theses and Dissertations
A new method for pre-impregnating nickel coated carbon fiber with a thermoplastic polymer to make towpreg, similar to a recently developed coating-line by João P. Nunes et al and a new electrically conductive thermoplastic are developed. A melted bath was used to help mitigate health concerns and waste for dispersion of nickel coated carbon fibers (NCF) in low density polyethylene (LDPE). This towpreg was then mixed with more LDPE or a mixture of LDPE and nickel nanostrands (NiNS) to a desired filler volume fraction to test the electrical conductivity of the composite. Some of these mixtures were then injection molded …
Investigation Of Rf Curing Parameters In Resin Infusion Molding,
2010
Brigham Young University - Provo
Investigation Of Rf Curing Parameters In Resin Infusion Molding, Christopher K. Love
Theses and Dissertations
The purpose of this study is to investigate RF or Radio Frequency energy as a viable alternative to traditional heating methods for the purpose of curing resins used in resin infusion molding, a molding system for polymeric composites. Traditional heating/curing methods include technologies such as room temperature, oven, microwave, infrared, and ultraviolet. Although RF curing provides far more advantages than disadvantages, its implementation into a manufacturing process can be challenging. Specifically, three critical elements must be present in order for RF to function in a manner that is profitable to the manufacturer. Those elements are: (1) the proper generator (voltage …
Manpower Cost Analysis Of A Distributed En Route Support Structure Versus A Consolidated En Route Support Structure,
2010
Air Force Institute of Technology
Manpower Cost Analysis Of A Distributed En Route Support Structure Versus A Consolidated En Route Support Structure, Phillip M. Rehmert
Theses and Dissertations
The United States military has developed an en route support structure for airlift requirements to deploy and sustain combat forces in conflict. The Air Mobility Command (AMC) is interested in determining the cost effectiveness of two distinctly different en route structures, in particular, the cost effectiveness of one large facility versus supporting combat forces with many smaller facilities. With the current operational tempo, continued analysis must be accomplished to determine if a smaller footprint is possible in the deployment and sustainment scenarios of conflicts seen today; conflicts more centered on a leaner and faster deployment force. This research examines the …
Development Of Measures To Assess Product Modularity And Reconfigurability,
2010
Air Force Institute of Technology
Development Of Measures To Assess Product Modularity And Reconfigurability, Amie C. Stryker
Theses and Dissertations
Several fundamental benefits of modularity are agreed upon by industry including reusability, flexibility, reconfigurability and extensibility. Interfaces within or between modules which establish provide/depend relationships are the focus of current modularity measures. This research outlines a new method and measures for assessing product modularity in terms of degree of coupling and the recognized modularity benefits. A five–step analysis process is developed and used to guide the modularity assessment. Defining and decomposing products are performed first. Using the resultant functional model from the first step, the identified functions are mapped to modules in a product in the second step. In the …
Cca: Exploratory Case Study Of Construction In A Contingency Environment,
2010
Air Force Institute of Technology
Cca: Exploratory Case Study Of Construction In A Contingency Environment, Michael J. Pluger
Theses and Dissertations
Top military leadership has identified problems with the timeliness and effectiveness of DoD contingency construction support. Qualitative data was collected in order to gain clarity on the problem space and lay a foundation for solution generation and selection. Interviews were conducted with agents with experience within the Iraq and Afghanistan theater of operation as well as support functions for the Pentagon. Commanders, Engineers, Lawyers, Acquisition Attorneys, Staff Officers and Program Managers have been interviewed. The interviews have been analyzed using open coding to answer research question and identify to emergent themes and concepts. The data collected has revealed that Contingency …
