Construction Engineering and Management Commons^™

Redefining Construction “As-Built” Plans To Meet Current Kentucky Transportation Cabinet Needs, Victoria Lynn Lasley

Theses and Dissertations--Civil Engineering

As-built drawings are the traditional method used by the construction industry to record changes made during construction. As-builts provide valuable information for new design projects as well as rehabilitation and remediation projects. The completeness and accuracy of these plans are essential for transportation industries and their success. While the importance of as-builts is widely recognized, the process of creating them has proven to be difficult. It is a time consuming process and entities often lack the resources necessary to complete accurate and detailed as-builts. After an investigation of current as-built operations within State Transportation Agencies, recommendations have been made to …

Improving Safety Performance Of Highway Maintenance Crews Through Pre-Task Safety Toolbox Talks, Zamaan Al-Shabbani

Theses and Dissertations--Civil Engineering

The dangerous work environment in the construction industry and the inherent high risks associated with construction work make it the focus of safety training and regulations. Highway construction and maintenance has unique hazards but seemingly less directly applicable safety standards, regulations, and programs. Department of Transportation (DOT) employees working in highway maintenance are exposed to a variety of unique hazards specifically associated with their work and not relating to the adjacent traffic. Yet, highway construction and maintenance work has not received sufficient attention in terms of safety research and programs. The lack of safety training and education in highway construction …

Hazard Recognition And Risk Perception Among Union Electricians, Elyas Jazayeri

Theses and Dissertations--Civil Engineering

Hazard recognition and risk perception are two important factors that are a focus of most safety training programs. According to previous research, unrecognized hazards could lead to underestimation of risks, which ultimately could lead to injuries and fatalities. The primary objective of this research was to assess hazard recognition and safety risk perception skills in the electrician trade among electricians in unions. Another goal of this study was to find possible correlation between level of engagement in safety training and hazard recognition and risk perception skills. The research objectives were accomplished by gathering data from sixty-seven apprentices and journeymen across …

Development Of A Readiness Model For The Application Of Precast Concrete In Housing Construction: A Case Study In Myanmar, Aung Phone Myint

Chulalongkorn University Theses and Dissertations (Chula ETD)

Precast concrete construction has been verified that it is one of the solutions for the growth of urbanization and housing development. In addition, it helps to reduce the labor requirement and material wastage in construction. However, the use of precast concrete technology is not still popular and not widely used within the Myanmar housing construction industry. Moreover, there is no readiness assessment model encompassed the readiness of construction industry including major stakeholders who are representatives of the construction industry for accepting the new technology. Therefore, the aim of this study is to develop a readiness model that can assess the …

แบบจำลองพฤติกรรมการเลือกใช้ยานพาหนะร่วมกัน: กรณีศึกษาผู้ใช้รถจักรยานยนต์รับจ้างในกรุงเทพมหานคร, วีรชัย โสธนนันทน์

Chulalongkorn University Theses and Dissertations (Chula ETD)

การบริการมอเตอร์ไซค์แชริ่งจะเป็นทางเลือกในเดินทางที่จะช่วยยกระดับคุณภาพชีวิตและเป็นทางเลือกการเดินทางของประชาชนในกรุงเทพมหานคร งานวิจัยนี้จึงมุ่งเน้นวิเคราะห์หาปัจจัยที่ส่งผลต่อการตัดสินใจเปลี่ยนรูปแบบการเดินทางของผู้โดยสารที่ใช้รถจักรยานยนต์รับจ้างมาเป็นการใช้บริการมอเตอร์ไซค์แชริ่ง โดยเจาะจงกลุ่มตัวอย่างเป็นผู้โดยสารที่ใช้บริการรถจักรยานยนต์รับจ้างเพื่อเชื่อมต่อกับระบบรถไฟฟ้าขนส่งมวลชนในพื้นที่ย่านศูนย์กลางทางธุรกิจของกรุงเทพมหานครจำนวน 349 ตัวอย่าง โดยใช้วิธีเก็บรวบรวมข้อมูลเชิงกล่าวอ้างด้วยการจำลองสถานการณ์สมมติ 6 สถานการณ์และสร้างแบบจำลองโลจิสติคทวินามบนพื้นฐานของทฤษฎีอรรถประโยชน์ นำข้อมูลมาวิเคราะห์ทางสถิติด้วยโปรแกรม Rstudio จากผลของการศึกษาพบว่าตัวแปรที่มีอิทธิพลเชิงบวกต่อการเลือกใช้บริการมอเตอร์ไซค์แชริ่งอย่างมีนัยสำคัญ ได้แก่ เวลาและค่าใช้จ่ายของรถจักรยานยนต์รับจ้าง ความเต็มใจจ่ายในการใช้บริการ ระยะเวลาเดินที่ยอมรับได้ ความถี่ในการใช้บริการรถจักรยานยนต์รับจ้างต่อสัปดาห์ การมีใบอนุญาตขับขี่รถจักรยานยนต์ สำหรับตัวแปรระยะทางในการเดินทาง สถานะภาพการสมรส จำนวนรถจักรยานยนต์และจำนวนรถยนต์ในครอบครองครอบครองส่งผลเชิงลบต่อการเลือกใช้บริการมอเตอร์ไซค์แชริ่ง โดยมูลค่าเวลาในการเดินทางของผู้โดยสารรถจักรยานยนต์รับจ้างของกลุ่มตัวอย่างมีค่าเท่ากับ 5.63 บาทต่อนาที

The Impact Of Extreme Virtual Elevation Above Grade On Construction Workers' Physiological Responses, Physical Responses, And Task Performance, Mahmoud Habibnezhad

Department of Construction Engineering and Management: Dissertations, Theses, and Student Research

On average, in every two work hours, one person dies from work-related injuries at construction sites. Most incidents are due to falling from elevated surfaces. Slips, trips, and loss of balance are the main causes. Studies suggest that instigating visual mismatch and physiological changes are among the most important reasons behind falling from narrow elevated surfaces. By using advanced virtual reality models, this dissertation aims to highlight some of the possible effects of a destabilizing environment (i.e., elevation above grade) on workers’ physiological responses and task performance. More specifically, this dissertation strives to find potential effects of elevation above grade …

The Influence Of Of Company Culture On Employee Satisfaction At Holder Construction: A Case Study, Callie Alexander

Construction Management

Since being founded in 1960, Holder Construction has grown to do work all across The United States and internationally as well. Today, repeat clients are what drive Holder’s core markets and provide eighty five percent of the work that Holder performs. The associates at Holder Construction believe their success stems from the company’s culture. The “Holder Way” is a slogan that encompasses all cultural attributes that Holder Construction expects their associates to embody. This case study evaluates Holder Construction’s effectiveness of their company’s cultural training in regards to employee satisfaction and fulfillment. Are these employees truly living out what is …

Osha-30 Interactive Laboratory Course, Matthew Bramlett

Construction Management

This course is aimed to give the students of the Construction Management (CM) department a more in depth knowledge on topics covered in the online OSHA-30 hour safety course. The online focuses on a wider range of topics that are covered in the OSHA-10 hour course that students are required to complete in CM 413: Jobsite Management, such as hazard communication, OSHA inspection procedures, industrial hygiene & bloodborne pathogens, and much more. The course will also include topics outside the scope of the 30-hour class such as: heavy equipment inspections, rigging safety and techniques, challenges of working in the marine …

Implementation Of Blockchain Technology In The Construction Industry, Steven Graham

Construction Management

In general, the construction industry has been pretty resistant to change. While most industries have gained in productivity over the years through implementation of new technologies and other factors, construction industry productivity has been on a steady decline since the 1960s. Even though there are a multitude of reasons for this, including more complex building types and a decline in the workforce, the major problem holding construction back are project management issues and alienation of project stakeholders in the construction process. Some improvements have been made to help with collaboration between parties, like BIM (building information modeling) and project management …

Logistics And Funding Plan For The Simpson Strong-Tie Lab Crane, Arya Ghourchian

Construction Management

In the recent years, there has been interests regarding an overhead crane to be erected inside of Cal Poly Simpson Strong Tie Lab (Building 187). This under running single girder crane system will be used for construction classes, and to lift heavy equipment. The erection of this 2 Ton indoor crane will be crucial to provide modular pieces, for whom that lost their homes due to the California fires. Additionally, there has been previous senior projects researches; reference attached preconstruction services, and a full structural analysis of SST Laboratory. I am in charge of collecting information regarding: Bid Estimate, Advertisement …

Reducing Energy Use In Excavators With Biodiesel, Omeed Abolfathi

Construction Management

In assessing the life-cycle cost of a building, the operation energy and construction energy are considered. The operation energy constitutes 90 to 95 percent of the lifetime energy use of a building. Concern over reducing operation energy has led to advancements where many buildings can now be considered net zero. While considerable advancements were made in achieving net zero in the operation, construction energy use has largely remained the same. To achieve net zero for the entire life-cycle of the building, construction energy consumption needs to be reduced. Excavators are one of the most popular pieces of construction equipment. They …

Ultra-High Performance Concrete For Precast Seismic Bridge Column Connection, Titchenda Chan

Electronic Theses and Dissertations

Accelerated bridge construction (ABC) utilizes prefabricated bridge elements constructed off-site, delivered, and assembled on-site to expedite construction time and reduce traffic disruption. ABC has been increasingly used for super- and sub-structure elements in low seismic regions. However, its application in medium and high seismic regions remain limited, particularly for precast columns where connections typically coincide with plastic hinge (PH) regions. Ultra-high performance concrete (UHPC), characterized by high compressive and tensile strength, and superior bond properties, is a potential material that can mitigate PH damage and enhance load transfer. This research proposes a new and simple damage tolerant precast column connection …

Analysis Of Standardized Concrete Mixes, Riley Graybeal

Williams Honors College, Honors Research Projects

Concrete is one of the most common materials used in construction. It is mass produced throughout the country, with numerous different designs for concrete mixes. A common practice among concrete manufacturers is to use a standardized concrete mix design. These standardized mix designs are pre-tested and are not usually altered frequently. The hypothesis of this research project is that manufacturers do not constantly investigate new ways to save on their mixes, and simply use the same standardized mix designs.

In this research, investigations into what alterations may reduce the cost of standardized mixes began with a baseline mix design provided …

Bs News January/February

Building Services Engineering

No abstract provided.

Analysis Of Demand On Shared Mobility Packages In University Campus, Sandar Win

Chulalongkorn University Theses and Dissertations (Chula ETD)

Shared mobility is the emerging service and comes in various forms. In Chulalongkorn University, innovative shared mobility services such as shared bicycle (CU Bike), small electric vehicle sharing (Ha:mo) and ride sharing tricycle (Muvmi) are offered along with conventional free bus (Pop bus) circulation. This study aimed to explore the attributes of the monthly mobility package which have effect on student’s decision while offering the integrated service package for CU students. Two phases of questionnaire surveys were conducted to find out the satisfaction on existing mobility services quality, barriers that discourage students from using shared mobilities, and factors that influence …

Public Private Partnership (Ppp): Sustainability In The Context Of Ppp Educational Building Projects, Renuka Rajput

Doctoral

This PhD research focuses on and examines the relationship between PPP procurement and sustainability and further aims to establish whether PPP projects can be sustainable with regards to social, enviornmnetal and economic sustainability. The scope of the research is primarily confined to the implementation of construction related sustainability practices within PPPs. It introduces various PPP concepts and critiques the underlying principles for the utilisation of PPP in education sector. This discussion leads to the identification of the core factors common to Sustainability and PPPs and the challenges facing the public and private partners in implementing sustainability in its entirety. In …

Notched Hollow Square Section Steel Column Buckling, Zia Razzaq, Solomon Tecleab

Civil & Environmental Engineering Faculty Publications

Presented in this paper is an outcome of a study to assess the effect of section loss in the form of longitudinal notches on the buckling load of hollow square section steel columns. The theoretical study includes buckling load estimates based on both an iterative equilibrium as well as a non-iterative energy approach. Buckling loads based on sample laboratory experiments are also presented. The study shows that the presence of a notch can significantly reduce the axial load-carrying capacity of a steel column.

Wind Load Analysis Of A High-Rise Building By Computational Fluid Dynamics, Canh Thiet Phung

Chulalongkorn University Theses and Dissertations (Chula ETD)

As new buildings become taller due to limited land area, often irregular in shapes for esthetics and some design constraints, wind load formula provided in design codes/standards cannot be applied because of the limitations. Wind tunnel test (WTT) is thus the suggested approach to obtain appropriate wind load for the design of such buildings. However, WTT is costly and time-consuming as it often requires much preparation of the small-scale model of the target building, instrumentation, and numerous realistic blocks of surrounding buildings (SBs). In this study, the CFD's accuracy will be evaluated by comparing its results to WTT by a …

Shear Wave Velocity Measurement Of Bangkok Clay Under Triaxial Testing With Various Stress Paths, Sirichai Pethrung

Chulalongkorn University Theses and Dissertations (Chula ETD)

Orientation paths of shear wave velocity for clayey soil subjected to multiple triaxial loading tests are dependent on complicated factors direction of stresses, void ratio, coefficient of earth pressure at rest, etc. However, most suggested the mean effective stress could provide a suitable correlation as well. In the present study, an identify the shear wave velocity under triaxial undrained small loading-unloading test , monotonic triaxial drained compression test , triaxial drained loading-unloading test , triaxial stress control test , drained triaxial extension , and undrained triaxial extension measured using the bender elements was presented. These results are indicated that the …

Seismic Enhancement Of Reinforced Concrete Columns With Lap Splices Using External Steel Collars, Pochara Kruavit

Chulalongkorn University Theses and Dissertations (Chula ETD)

This research investigated the behavior of reinforced concrete (RC) columns with lap splices and mechanical splices. The study conducted the full-scale test and predicted a lateral load capacity using the proposed numerical model. The test configuration was a cantilever column subjected to a cyclic lateral loading and a constant gravity load. The tested specimens consisted of the RC column without lap splices, RC columns with spliced reinforcement including lap splices and mechanical splices, and RC column with lap splices strengthened by external steel collars. The experimental result indicated that the lateral load capacity of the RC column with mechanical splices …