Civil Engineering Commons^™

Precast Concrete Pavement Practices Overview, Shiraz Tayabji

JTRP Affiliated Workshops

No abstract provided.

Overview Of Illinois Tollway Precast Panel System, Steve Gillen

JTRP Affiliated Workshops

No abstract provided.

Super-Slab® Precast Pavement System, Dan E. Moellman

JTRP Affiliated Workshops

No abstract provided.

Precast Concrete Pavement Practices—Generic System Use In Michigan, Texas & California, Shiraz Tayabji

JTRP Affiliated Workshops

No abstract provided.

Infant Exposure To Resuspended Particles From Carpeted Flooring: Experimental Chamber Study With A Simplified Mechanical Crawling Infant, Manjie Fu, Brandon E. Boor

The Summer Undergraduate Research Fellowship (SURF) Symposium

Airborne particles of biological origin – bioaerosols – are present everywhere, including the indoor environment where people spend considerable amounts of time, and exposure to such materials via inhalation can have a number of health implications. Bioaerosol dynamics can occur through a variety of mechanisms, among them resuspension of deposited particles due to human activity. Because the breathing zone of infants is at a much lower height than that of adults, there is reason to suspect that infants are exposed to greater concentrations of bioaerosols resuspended from the floor, though knowledge in this specific area is limited. To investigate, a …

Development Of A New Nanohub Simulation Tool: Coarse Graining Of Crystalline Nano-Cellulose., Kuo Tian, Mehdi Shishehbor, Pablo Zavattieri

The Summer Undergraduate Research Fellowship (SURF) Symposium

Crystalline Nano-cellulose (CNC) is a general molecular structure obtained from acid hydrolysis of native fiber. They are often very short (100 to 1000 manometers) and the mechanical properties of CNC varies depend on length scale. Due to defect formation of the structure, the mechanical properties of the material composed of such CNC may vary drastically. This study was to provide a numerical tool to integrate a few valid modules and to better understand the mechanical properties of CNC and the overall performance of the bio-inspired material composed of CNC. Our focus is mainly on two type of composite structure [1] …

Strength Of Reinforced Concrete Beams With High-Strength Steel, Brian C. Rogers, Aishwarya Puranam, Santiago Pujol

The Summer Undergraduate Research Fellowship (SURF) Symposium

Structures are commonly made of reinforced concrete, which is a composite material made of concrete and steel reinforcement. Using high-strength steel, with yield stress larger than 100 ksi, could help reduce the quantity of steel required in structural members, thus reducing costs and improving constructability. The hypothesis being tested is that smaller quantities of high-strength steel reinforcement (HSSR) can be used in place of conventional steel in reinforced concrete beams while maintaining similar strength and deformation at failure. Two reinforced concrete beams with two different types of longitudinal steel reinforcement were constructed. The beams were 18 in. wide, 30 in. …

High Strength Steel In The Reinforced Concrete Structures: Serviceability, Alan Kanybek, Aishwarya Puranam, Santiago Pujol

The Summer Undergraduate Research Fellowship (SURF) Symposium

The use of high-strength steel (yield stress larger than 100 ksi) in reinforced concrete structures can provide an effective alternative to using conventional steel (yield stress up to 80 ksi). The goal of this study is to investigate if slabs with reduced quantities of high-strength steel reinforcement meet the serviceability criteria. Instantaneous and long-term deflections in slab specimens with conventional steel and reduced amounts of high-strength steel (as compared with conventional steel) were studied. Two sets of two reinforced concrete slabs, each 14 ft. long, 30 in. wide, were built. The depth, quantity, and type of longitudinal reinforcement were varied …

Study On Oil Palm Fresh Fruit Bunch Bruise In Harvesting And Transportation To Quality, Andreas Wahyu Krisdiarto, Lilik Sutiarso

Makara Journal of Technology

There are losses of production due to oil palm field’s material handling. Activities that may raise the losses are harvesting and transportation, which may cause bruise and damage to fruit. This research was aimed to learn the bruise of fresh fruit bunch (FFB) phenomenon in harvesting and transportation. Method used in this research was measuring the bruise area resulted by FFB falling when harvested, loading (throwing up) FFB to truck bin, and transporting using truck. These data, coupled with weight of bruised fruit, were calculated to get FFB bruise index. Each FFB bruise index is related to potential free fatty …

Automatic Arrhythmia Beat Detection: Algorithm, System, And Implementation, Wisnu Jatmiko, I Md. Agus Setiawan, Muhammad Ali Akbar, Muhammad Eka Suryana, Yulistiyan Wardhana, Muhammad Febrian Rachmadi

Makara Journal of Technology

Cardiac disease is one of the major causes of death in the world. Early diagnose of the symptoms depends on abnormality on heart beat pattern, known as Arrhythmia. A novel fuzzy neuro generalized learning vector quantization for automatic Arrhythmia heart beat classification is proposed. The algorithm is an extension from the GLVQ algorithm that employs a fuzzy logic concept as the discriminant function in order to develop a robust algorithm and improve the classification performance. The algorithm is tested against MIT-BIH arrhythmia database to measure the performance. Based on the experiment result, FN-GLVQ is able to increase the accuracy of …

Optimization Of Electricity Generation Schemes In The Java-Bali Grid System With Co2 Reduction Consideration, Farizal Farizal, Wenty Eka Septia, Amar Rachman, Nasruddin Nasruddin, Teuku Meurah Indra Mahlia

Makara Journal of Technology

This research considers the problem of reducing CO2 emissions from the Java-Bali power grid system that consists of a variety of power-generating plants: coal-fired, natural gas, oil, and renewable energy (PV, geothermal, hydroelectric, wind, and landfill gas). The problem is formulated as linear programming and solved using LINGO 10. The model was developed for a nation to meet a specified CO2 emission target. Two carbon dioxide mitigation options are considered in this study, i.e. fuel balancing and fuel switching. In order to reduce the CO2 emissions by 26% in 2021, State Electric Supply Company (PLN) has to generate up to …

Apparent Porosity And Compressive Strength Of Heat-Treated Clay/Iron Sand/Rice Husk Ash Composites Over A Range Of Sintering Temperatures, M. Nizar Machmud, Zulkarnain Jalil, Mochammad Afifuddin

Makara Journal of Technology

Novel composites of clay/iron sand/rice husk ash (RHA) have been developed. Electric furnace was used to perform heat treatment on the composites to study the effect of sintering temperature on their apparent porosity and compressive strength. Two types of RHA with different bulk density were prepared to gain an understanding of the influence of apparent porosity on compressive strength of the heat-treated composites over a range of sintering temperatures. Heattreated composites, made of clay/iron sand and clay/RHA, were also prepared as a referenced material. X-ray diffraction (XRD) analysis was further performed to comprehensively discuss the role of iron sand on …

The Effect Of Irradiation Of Fe And Ar Ion On The Surface Morphology Of Diamond Thin Film Related To The Magnetoresistance Property, Salim Mustofa, Setyo Purwanto, Kenji Mishima

Makara Journal of Technology

The irradiation of Fe and Ar ion was applied on the surface of diamond/Si thin film to know its effect on the morphology of thin film.The magnetoresistance property was also studied. Ion irradiation treatment using Fe ion followed by argon ion at the energy of 70keV and a dose of 1 x 1015 ion/cm2 have been conducted on the surface of two types of thin film, diamond/Si (111) and diamond/Si (100). Both thin films were made by using a CVD method, and the thickness of the thin film is 1000-nm. From simulations using the software called Stopping and Range of …

Use Of Green Mussel Shell As A Desulfurizer In The Blending Of Low Rank Coal-Biomass Briquette Combustion, Mahidin Mahidin, Asri Gani, M. Reza Hani, Muhammad Syukur, Hamdani Hamdani, Khairil Khairil, Samsul Rizal, Abdul Hadi, T.M.I. Mahlia

Makara Journal of Technology

Calcium oxide-based material is available abundantly and naturally. A potential resource of that material comes from marine mollusk shell such as clams, scallops, mussels, oysters, winkles and nerites. The CaO-based material has exhibited a good performance as the desulfurizer or adsorbent in coal combustion in order to reduce SO2 emission. In this study, pulverized green mussel shell, without calcination, was utilized as the desulfurizer in the briquette produced from a mixture of low rank coal and palm kernel shell (PKS), also known as bio-briquette. The ratio of coal to PKS in the briquette was 90:10 (wt/wt). The influence of green …

The Knowledge-Based Analysis On Medium Resolution Images Of Remote Sensing To Extraction Information Land Use Type Scs-Cn, The Case Study On Grompol Watershed, Puguh Dwi Raharjo, Totok Gunawan, Mohammad Pramono Hadi

Makara Journal of Technology

Remote sensing imagery Landsat-8 is one image that has a good temporal resolution; in addition to the availability of data, this image can be obtained free of charge. Land cover type SCS-CN is part of a unit of land that affects runoff. The use of medium resolution imagery in reducing the SCS-CN land use type is considered relatively difficult, and it yields less good accuracy. Limitations on multispectral classification only rely on facts derived from spectral reflection, so that the two data are the same since different characteristic results are not so good. This study aims to determine the accuracy …

Sugarcane Bagasse As A Carrier For The Immobilization Of Saccharomyces Cerevisiaein Bioethanol Production, Sita Heris Anita, Wibowo Mangunwardoyo, Yopi Yopi

Makara Journal of Technology

Sugarcane bagasse was used as a carrier to immobilize Saccharomyces cerevisiae in bioethanol production. This research aims to study the potential use of sugarcane bagasse as an alternative carrier for cell immobilization and improvement in the production process of cell immobilization in bagasse. The results showed that the physical characteristics of sugarcane bagasse as a carrier were water content (7.77 ± 0.35%), water retention (4.80 ± 0.44 g/g), water absorption index (8.58 ± 0.22 g/g), and lignin content (24.40 ± 1.52 %). Determination of cell retention was performed in an inoculum volume of 50 mL yeast suspension with various carrier …

Modeling, Control, And Impact Analysis Of The Next Generation Transportation System, Feng Zhu

Open Access Dissertations

This dissertation aims to develop a systematic tool designated for connected and autonomous vehicles, integrating the simulation of traffic dynamics, traffic control strategies, and impact analysis at the network level.

The first part of the dissertation is devoted to the traffic flow modeling of connected vehicles. This task is the foundation step for transportation planning, optimized network design, efficient traffic control strategies, etc, of the next generation transportation system. Chapter 2 proposes a cell-based simulation approach to model the proactive driving behavior of connected vehicles. Firstly, a state variable of connected vehicle is introduced to track the trajectory of connected …

Laboratory Characterization Of #2q-Rok Sand, Wilson Fernando Espinoza Chavez

Open Access Theses

A series of laboratory tests were performed in a sand commercially known as #2Q-ROK to determine its response to loading. #2Q-ROK is a poorly-graded, clean silica sand composed of 99% of quartz (SiO2). Its specific gravity is 2.65 and its maximum and minimum void ratios are 1.03 and 0.7, respectively. In the absence of crushing, the #2Q-ROK sand direct shear critical-state friction angle is 32.8° and the ring shear critical-state friction angle is 29.6°.

One-dimensional compression tests were performed on samples compressed to a normal stress of 24,851.36kPa for time periods ranging from 4 hours to 11 days. The maximum …

Improving The Laboratory Design Of Asphalt Mixtures To Enhance Asphalt Pavement Durability, Ali Hekmatfar

Open Access Dissertations

Most departments of transportation, including Indiana’s, currently use the Superpave mixture design method to design asphalt mixtures. This method specifies that the optimum asphalt content for a given gradation be selected at 4 percent air voids. During construction, these mixtures are typically compacted to 7-8 percent air voids. If mixtures were designed to be more compactable in the field they could be compacted to the same density as the laboratory mixture design, which would increase pavement durability by decreasing the in-place air voids. The objective of this research was to enhance the asphalt mixture design method in order to increase …

The Long-Term Performance Of Concrete Crack And Deck Surface Sealers, Emily A. Byl

Open Access Theses

Concrete bridge decks in the State of Indiana are undergoing continuous deterioration and loss of service life due to the use of deicing salts during winter weather conditions. As salt water penetrates the deck through cracks and the concrete surface, chlorides, water and oxygen are able to access the reinforcement to initiate corrosion. The corrosion of reinforcing steel over time creates an ongoing need for costly deck repairs and/or deck replacement. This study investigates the performance of crack sealers and deck surface sealers as a potentially cost-effective method of increasing bridge deck service life. An experimental program was developed and …