Mechanical Engineering Commons^™

The Role Of Si3n4 Amorphous Phase In Nc-Tin/A-Si3n4 Nanocomposites In Increases The Hardness And Thermal Stability, Keba Moto

Makara Journal of Technology

The role of Si3N4 amorphous phase in nc-TiN/a-Si3N4 nanocomposites will be shown and compared with polycrystalline ZrN/Ni which has no such amorphous phase (non-composites). The presence of amorphous phase Si3N4 increases the hardness of film as well as the toughness of the bulk nanocomposites under indentation load. It has been observed that nc-TiN/a-Si3N4 nanocomposites films has higher thermal stability than ZrN/Ni polycrystalline films.

Alternative Ways To Teaching Hvac And Related Subjects Through Actual Project Involvement-Three Case Studies, Samir F. Moujaes

Mechanical Engineering Faculty Research

No abstract provided.

Develops The Software Of Dsp Processor For The Cdma Circuitry, Arman Djohan D.

Makara Journal of Technology

This research develops the software of DSP Processor type TMS320C54X for the CDMA circuitry. This research apply two algorithms namely Mathematic Algorithm and table lookup Algorithm. From both algorithms, the research examine what algorithm have the fasted processing time and the smallest memory occupation. From the examination results the Mathematic Algorithm have 20.62 milliseconds processing time and the Table lookup algorithm have 14.08 milliseconds processing time. The Table lookup algorithm have the fastest processing time because the Matematic algorithm need the rounding process of the fi gure. Eventhough such processing time is not exceed from the 125 millisecond of delay …

The Manufacturing Properties Of Galvanised Steel Sheet With Hexagonal And Tetragonal Network Of Circle Holes, Rahmat Saptono

Makara Journal of Technology

Galvanized steel sheet of 0.8 mm in thickness was drilled with circle holes of 2.5 mm diameter and spacing arranged in tetragonal and hexagonal pattern. The manufacturing properties of specimen were studied through drawing and stretching simulative test. It was concluded from the results that, at high ratio of punch to hole diameter (40/2.5), the drawing properties (LDR) of both square and hexagonal perforated sheet were slightly lower than that of solid sheet, while hexagonal perforated showing LDR somewhat higher than the square one. The stretching properties (LDH) of sheet, however, were much lower than that of solid sheet while …

Object Classfification In Computer Vision With Discriminant Analysis, Amir Hamzahan

Makara Journal of Technology

A robotic sensor system is always supported by a computer system called ‘computer vision’. The important concept of computer vision is object classfifi cation. In this study two algorithms for object classifi cation in this system will be compared. Firstly, A simple method that do not need complex computation and that considered as an informal method is called binary tree decision structure. This method is based on modest caracteristic decriptors of an object such as vertical line, horizontal line or ellipse line. Unfortunately this method has weakness in recognize an image that contaminated by a noise. Secondly, a more formal …

Integrating Passenger And Modulo As Learning Tools For Collaborative Engineering Education, Kalamullah Ramli, Frank Schwarz, Stefan Werner, A Halim Shamsuddin, Axel Hunger

Makara Journal of Technology

The University of Indonesia (UI), Gerhard Mercator University (GMU), the Universiti Kebangsaan Malaysia (UKM) have agreed to cooperate as partners to develop a joint bachelor (3+1) and masters (1+1) degree, and collaborate in the research fi elds of multimedia- and internet-based learning and application level active networks. This paper describes the introduction of the Offshore Project and the extending of information technology applications to the partner institutions in this international cooperation which would very much enhance the operations of the new initiative in engineering education, which could provide students in far distance with more fl exible learning environment.

Effects Of 0.25 % Mo (Molybdenum) Which Is Contained In The Ductile Cast Iron On Mechanical Properties Of Austempered Ductile Iron (Adi)., Nukman Nukman, Bustanul Arifin, Bambang Sugiarto

Makara Journal of Technology

The aim of this research is to investigate the effects of 0.25 % Mo (Molybdenum) which is contained in the ductile cast iron on mechanical properties of Austempered Ductile Iron (ADI). The various temperatures and the holding times are used in the heat treatment processes. Using a given 0.25 % Mo in the ductile iron, ADI's alloyed developes a higher ultimate tensile stress value and decreases the elongation if we compare with the as cast (non alloy ductile iron). The higher impact energy value obtained at 9000 C austenization and 375o C austempering temperatures during 60 minutes holding times. The …

Making Alloys (Ti1 - Xalx) N Using Plasma Cvd Technique From Alcl3 Powder, H2 And N2 Gas ,With Solvent Ticl4, Keba Moto

Makara Journal of Technology

The substitution of Ti atoms by Al atoms in TiN lattice sites to form (Ti1-xAlx)N is clearly demonstrated by the coatings which were deposited on steel substrate and using plasma CVD technique. The presence of Al atoms in TiN lattice site is shown by means of XRD and EDX techniques: lattice parameters decreasing of TiN as the fraction of Al increases (XRD) and precipitation of hexagonal AlN phase (XRD) as the fraction of Al exceeding 0.8 (EDX). The hardness of these coating are just around 30 GPa, which is beyond the values reported in literatures.

Study Effect Of Salt Washing Process On Content And Iodium Stability Of Salt, Nelson Saksono

Makara Journal of Technology

Effect of Salt Washing Process on Content and Iodium Stability of Salt. Salt washing process should increase the salt quality. It should clean the salt from sludge or clay and also reduce the impurity compound such as Mg, Ca and the reductor content. The objective of these reseach is to assess the effect of washing process on the content og hygroscopic impurities compound (Ca and Mg), and reductor content of salt. The research also investigate the water absorbing, pH, KIO3 content as function of time to obtain effect of washing process on KIO3 stability in salt. The experiment result shows …

Forensic Investigation Of Failed Mast Arms Of Traffic Signal Supported Structures, Genda Chen, Michael G. Barker, D. Scott Mackenzie, Christopher W. Ramsay, Joe Alderson, Lokeswarappa R. Dharani, Jiaqing Yu

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In Missouri, 11 traffic signal mast arms fractured at the arm-post weld connection in 7 years. To reduce this fatigue failure, the Missouri Department of Transportation developed a fatigue-resistant weld profile that increases the weld leg and reduces the slope of the weld at the toe. This study investigated causes of the failed arms, compared performance of new and old weld profiles, and suggested retrofitting measures for further investigation. The scope included a metallurgical investigation of one failed field mast arm, laboratory fatigue testing of five prototype mast arms (two new and three old profiles), and laboratory failure analysis of …

Application Of Dynamic System Identification To Timber Beams - Part Ii, S T. Peterson, D I. Mclean, M D. Symans, David Pollock, W F. Cofer, R N. Emerson, Kenneth J. Fridley

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

In a companion paper, a method of global nondestructive evaluation (NDE) for identifying local damage and decay in timber beams was developed and verified analytically using a finite-element model of a timber beam. The previously presented method of damage localization employs experimental modal analysis and an algorithm that monitors changes in modal strain energy between the mode shapes of a damaged beam with respect to the undamaged state of the beam. In this second part of a two-part paper, experimental laboratory tests on simply supported timber beams are presented to verify the capabilities and determine the limitations of the proposed …

Application Of Dynamic System Identification To Timber Beams - Part I, S T. Peterson, D I. Mclean, M D. Symans, David Pollock, W F. Cofer, R N. Emerson, Kenneth J. Fridley

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

In this first part of a two-part paper, development of a method of dynamic system identification for timber beams is presented with an analytical verification of the method using a finite-element model. A method of global nondestructive evaluation for identifying local damage and decay in timber beams is investigated in this paper. Experimental modal analysis is used in conjunction with a previously developed damage localization algorithm. The damage localization algorithm utilizes changes in modal strain energy between the mode shapes of a calibrated model, representing the undamaged state of the beam of interest, and the experimentally obtained mode shapes for …

Fatigue Assessment Of Traffic Signal Mast Arms Based On Field Test Data Under Natural Wind Gusts, Genda Chen, Jingning Wu, Jiaqing Yu, Lokeswarappa R. Dharani, Michael G. Barker

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In recent years, several states including Missouri, Wyoming, California, and Texas experienced fracture failures of traffic signal mast arms. Almost all the failures are associated with the propagation of defects or cracks. It is therefore imperative to evaluate existing mast arms using a simple yet accurate procedure. A statistical methodology is proposed to predict the fatigue life of signal mast arm structures on the basis of field-measured strain data. The annual occurrence of various stress levels is determined using the historical wind speed data in the vicinity of a mast arm structure and the strain readings of the structure under …

Matrix Structural Analysis, 2nd Edition, William Mcguire, Richard H. Gallagher, Ronald D. Ziemian

Faculty Books

The aims of the first edition of Matrix Structural Analysis were to place proper emphasis on the methods of matrix structural analysis used in practice and to lay the groundwork for more advanced subject matter. This extensively revised Second Edition accounts for changes in practice that have taken place in the intervening twenty years. It incorporates advances in the science and art of analysis that are suitable for application now, and will be of increasing importance in the years ahead. It is written to meet the needs of both the present and the coming generation of structural engineers.

KEY FEATURES …

Finite Element Simulation Of Creep Buckling Of Cipp Liners Under External Pressure, Qiang Zhao

Doctoral Dissertations

The problem of long-term structural behavior of CIPP liners under external hydrostatic pressure has been characterized as a structural instability problem which is induced by time-dependent material deformation or creep. It is also a contact problem since the liner deflection is externally constrained by the host pipe. The intrinsically nonlinear problem is investigated by means of finite element simulation, with emphases on (a) the essential structural behaviors and mechanisms of buckling, and (b) the influences of inelastic material properties (i.e. yield strengths and creep rates) and geometrical parameters on liner's buckling resistance.

A liner first deforms as a free pipe …

Micro Hydro Power, Frederick J. Munster

Maine Collection

Micro Hydro Power

by Frederick J. Munster

Department of Economic and Community Development, August, Me. 1999 (?).

Contents: Introduction / History of Hydropower in Maine / Renewables / Why Micro Hydro / Determining Flow / Determining Head / Estimating Energy Potential / Hydro Turbines / Dams, Impoundments, Penstocks and Power Houses / Utility Interconnected Systems / Battery Charging Systems / Operation and Maintenance / Economics / Regulation of Hydro Development / For More Information / References

Lateral Resistance Of Ring-Shank Nail Connections In Southern Pine Lumber, R D. Theilen, D A. Bender, David Pollock, S G. Winistorfer

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

Ring-shank nails are used in engineered structures with lateral connection design values based on theoretically derived equations which were validated only for common nails. The goal of this study was to quantify the input parameters and lateral connection strength of several types of ring-shank nails in Southern Pine lumber and critically evaluate the applicability of the theoretical equations for ring-shank nails.

Two sizes of galvanized and ungalvanized, hardened steel ring-shank nails from two manufacturers were studied. The hardened, ring-shank nails carried significantly higher loads than the common wire nails studied. Because the current method of determining yield load does not …

The Study Of Wave-Blocking And Current Effects On Nonlinear Interactions Of Shallow-Water Waves Using Advanced Boussinesq Models, Qin Chen

Civil & Environmental Engineering Theses & Dissertations

The first part of this work focuses on the derivation of enhanced Boussinesq-type equations for the combined motion of waves and currents in shallow water areas.

The strategy proposed in this work is to couple two known methods which are the sponge layer concept suitable for short waves and Sommerfeld radiation condition for currents. This coupling method provides satisfactory non-reflective boundaries for the simulation of fully coupled wave/current motion as demonstrated by the numerical experiments. We verify the model against the well known solutions based on the existing theories and good agreement has been observed. The numerical results confirm the …

Withdrawal Strength Of Ring-Shank Nails Embedded In Southern Pine Lumber, M J. Skulteti, D A. Bender, S G. Winistorfer, David Pollock

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

Ring-shank nails are used extensively in post-frame construction due to their superior performance, yet surprisingly little testing has been done on nail sizes above 12d. Experience in the post-frame industry suggests that published allowable design values for ring-shank nails may be overly conservative and need revision. The goal of the research reported herein was to characterize the withdrawal strength of ring-shank nails embedded in Southern Pine lumber. Three sizes ofgalvanized and ungalvanized (bright) ring-shank nails from two manufacturers were studied. Ring-shank nails had approximately twice the withdrawal resistance of smooth-shank nails of the same diameter. Galvanizing slightly reduced withdrawal strength …

Comprehensive Conjunctive-Use Management Of Connected Surface Water Groundwater Systems Using Stochastic Inputs And Uncertainties, Seshadri Suryanarayana

Civil & Environmental Engineering Theses & Dissertations

A comprehensive conjunctive-use management model is developed. The dynamics of flow and solute transport processes in connected surface water groundwater systems are integrated by a dual programming management model. The governing aquifer flow parameters and streamflows are treated as stochastic random processes. Multiple realizations of the random field are generated and are explicitly incorporated in a non-linear optimization model along with other system, environmental, and management constraints. To facilitate management of large aquifer systems, a linked simulation-optimization approach is used. The simulation program generates the response matrices for flow and transport processes. The management model then determines optimal well discharges …

A One-Dimensional Model For Storm Breaching Of Barrier Islands, Cheol Shik Shin

Civil & Environmental Engineering Theses & Dissertations

A set of numerical models is developed for simulating the four stages of barrier breaching characterized by one horizontal spatial dimension.

The SBEACH model is employed for the first stage of dune/beach erosion. The Lax-Wendroff two-step explicit scheme for Stage II is developed to simulate initiation of ocean flood propagation on initially dry barrier islands and the method of characteristics (MOC), is employed to compute additional boundary data. The development of the Preissmann implicit scheme for water motion and a forward time centered space explicit scheme for sediment motion in Stages III and IV provide a tool to study the …

The Progressive Failure Analysis Of Cut Slope In Anisotropic Strain Softening Soils, Jong Woon Choi

Civil & Environmental Engineering Theses & Dissertations

The failure phenomena in earth structures such as slopes and embankments on clay foundations are a consequence of the formation of failure surfaces.

A finite difference computer code, FLAC (Itasca Consulting Group, 1993), with the isotropic Mohr-Coulomb plasticity model, is used to analyze the undrained progressive failure of a strain softening soil during a slope excavation process. The focus of the study is on the short-term stability of slopes. In the first series of analyses, which are aimed at the evaluation of anisotropic strength effect on slope stability, the isotropic Mohr-Coulomb plasticity model is slightly modified to implement the anisotropic …

Threaded-Nail Fasteners - Research And Standardization Needs, B L. Wills, S G. Winistorfer, D A. Bender, David Pollock

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

Threaded nail fasteners are commonly used in agricultural and commercial post-frame structures, yet there has been insufficient research to fully understand the effect of threads on withdrawal and lateral load resistance. The objective of this article is to review technical information on threaded nail fasteners and to identify problems facing manufacturers, designers, and users of threaded nail fasteners for engineering applications. Recommendations are given concerning research and standardization needs.

Micromechanics Of Granular Materials And Its Relation To Wave Velocity, Tarun K. Agarwal

Civil & Environmental Engineering Theses & Dissertations

The macro characters of the granular materials depend upon micromechanical parameters such as the void ratio, particle shape, contact force distribution, and initial state of the fabric of the assembly. Since it is difficult to evaluate these internal parameters from laboratory experiments, a macro measure is desired which depends directly on these internal parameters. One such measure has been shown to be dynamic shear modulus but it was incomplete in predicting directional changes in the internal parameters. Therefore, it is hypothesized here that the complete elastic moduli matrix will have more direct information about the internal parameters, especially the dynamic …

Nonproportionally Loaded Steel Beam-Columns And Flexibly-Connected Nonsway Frames, Siva Prasad Darbhamulla

Civil & Environmental Engineering Theses & Dissertations

A theoretical study of the inelastic stability of nonproportionally loaded steel beam-columns and flexibly-connected frames is conducted. Specifically, solution techniques are formulated to predict the nonlinear behavior of cross sections, spatial beam-columns, and nonsway plane frames under the combined influence of imperfections, flexible connections, and nonproportional loads. A set of new inelastic slope-deflection equations for imperfect members are derived and their use illustrated through in-depth studies of flexibly-connected portal and two-bay two-story frames. These equations are derived from a system of nonlinear ordinary differential equations. The member studies are carried out using a second-order finite-difference solution to a set of …

Feasibility Study Of Maine's Small Hydropower Potential, James D. Sysko

Maine Collection

Feasibility Study of Maine's Small Hydropower Potential

Prepared by James D. Sysko, Small Hydro East, for the Maine State Planning Office, Maine Office of Energy Resources, January 1989.

"This study focuses on finding potential hydropower sites of approximately 50 kw to 1000 kw in capacity."

Post-Buckled Performance Of Partially Restrained And Intermediately Supported Steel Angles, Perumal Radhakrishnan

Dissertations and Theses

The post-buckled performance of cross-braced single angles was experimentally determined. The results of this study will be used by the Bonneville Power Administration for the analysis of member performance in transmission towers.

Fundy Tidal Power Development : Preliminary Evaluation Of Its Environmental Consequences To The Resources Of The State Of Maine, Bigelow Laboratory For Ocean Sciences

Maine Collection

Fundy Tidal Power Development : Preliminary Evaluation of Its Environmental Consequences to the Resources of the State of Maine

A Report to the Maine State Planning Office by the Bigelow Laboratory for Ocean Sciences, April, 1984.

"Technical Report No. 35 - Bigelow Laboratory for Ocean Sciences, West Boothbay Harbor, Maine - A Division of Northeastern Research Foundation, Inc."

Contents: Executive Summary / Introduction / Methods / Physical and Biological Consequences / Socio-Economic Consequences / Research Needs / Bibliography / Appendix I. Written Comments on Greenberg Model

Stability Analysis Of Closed Surge Tanks By Phase-Plane Method, Mostafa A. Sabbah

Civil & Environmental Engineering Theses & Dissertations

The governing equations describing water level oscillations in a closed surge tank with compressed air at the top of the tank are a set of nonlinear ordinary differential equations if the hydraulic system is analyzed as a lumped system. These oscillations are stable or unstable depending on the parameters of the plant and the type and magnitude of the disturbance.

The present available stability criterion has been developed by linearizing the governing equations and is, therefore, valid only for small disturbances.

In the research reported herein, the governing equations are normalized to reduce the number of parameters from nine to …