Mechanical Engineering Commons^™

Immittance Response On Carboxymethyl Cellulose Blend With Polyvinyl Alcohol- Doped Ammonium Bromide-Based Biopolymer Electrolyte, Norfatihah Mazuki, Yuki Nagao, Ahmad Salihin Samsudin

Makara Journal of Technology

The blended carboxymethyl cellulose (CMC) and polyvinyl alcohol (PVA) doped with various compositions of ammonium bromide (NH4Br)-based solid biopolymer electrolytes (SBEs) were prepared by using the casting method. In this present work, CMC/PVA–NH4Br SBE thin film was used to investigate the electrical conductivity via electrical impedance spectroscopy. The maximum conductivity obtained was 3.21 X 10−4 S cm−1 for sample AB20 at ambient temperature (303 K), and this result might be due to the increased number of charge carrier. A dielectric study was conducted to understand the conductivity behavior. The electrical properties have been measured as a function of frequency of …

Automated Compilation Test System For Embedded System, Mohamad Khairi Ishak, Ooi Jun Hwan, Teh Jiashen, Nor Ashidi Mat Isa

Makara Journal of Technology

Embedded system testing involves testing an integration of software and hardware. It is increasingly difficult to evaluate the functionality of each module within a short time because of the increasing number of tests required. In this paper, a novel stepwise methodology involving the use of an automated compilation test system (ACTS) is proposed, to improve the quality of testing and optimize the testing time using automation. Using the proposed method, the testing coverage can be maximized, while minimizing the manual work and testing time required. This ACTS was used to automate the test code compilation and execution for different hardware …

Transition Metal Dichalcogenide For High-Performance Electrode Of Supercapacitor, Saifful Kamaluddin Muzakir, Ahmad Salihin Samsudin, Bouchta Sahraoui

Makara Journal of Technology

Molybdenum dichalcogenides have been reviewed from the perspectives of bandgap, conductivity, and oxidation states of transition metal. Researchers have concluded that a narrow-bandgap transition metal dichalcogenide with high conductivity could be achieved for the high-performance electrode of a supercapacitor.

Ascorbic Acid Degradation In Cut Lemon Packaged Using Oxygen Scavenging Active Film During Storage, Kurniawan Yuniarto, Setyo Purwanto, Bruce Ari Welt, Anang Lastriyanto

Makara Journal of Technology

Oxygen scavenging active film can be used to prevent diffusion of free oxygen due to the action of permeation mechanism. In this study, biodegradable oxygen scavenging plastic film was designed by incorporating an antioxidant agent into plasticized polylactic acid or PLA-PEG (PPLA). Butylated hydroxytoluene (BHT) was added at different concentrations into the matrix of the PPLA film using a direct casting method to produce oxygen scavenging active film. The antiradical activity of the oxygen scavenging active film was observed, which could be applied for preventing vitamin C degradation in cut lemon during storage. The antiradical activity of the active film …

A 2.3/3.3-Ghz Dual Band Low Noise Amplifier Using Switchable Load Inductor In 0.18-Um Cmos Technology, Taufiq Alif Kurniawan, Hsiao-Chin Chen

Makara Journal of Technology

In this paper, the dual band low noise amplifier is designed in 0.18-μm CMOS technology. By combining the proposed switchable load inductor for gain controlling and the conventional inductive source degeneration topology, narrow band gain and good impedance matching are achieved at 2.3/3.3-GHz frequency bands. The new mathematical analysis of low noise amplifier design is derived to define the component parameters of the proposed circuits. The proposed low noise amplifier exhibits gain of 17.18 dB and 15.5 dB, and noise figure of 2.67 dB and 2.52 dB at the two frequency bands, respectively.

Conversion Of Heat Energy From Cooling Water Of Diesel Engine To Electrical Energy Using Thermoelectric Generator, Muhammad Hasan Albana

Makara Journal of Technology

This research objective is to convert heat from the radiator fluid of a diesel engine to electrical energy by utilizing a thermoelectric generator (TEG). The TEG consists of 20 semiconductors (TE modules) and is equipped with a heat sink. The research shows that using the TEG, the heat of radiator fluid can be converted to electrical energy, although the electricity generated is small. The maximum electrical voltage generated by the TEG when modules were connected in series was 10 volts. When the TE modules were connected in parallel and series-parallel, the maximum voltages generated were 2.11 and 2.53 volts, respectively. …

The Importance Of Usability Aspect In M-Commerce Application For Satisfaction And Continuance Intention, Yassierli Yassierli, Vinsensius Vinsensius, M. S. Syed Mohamed

Makara Journal of Technology

There has been a rapid growing of m-commerce application in recent years due to the development of mobile communication technology and e-commerce business. However, only about 30% of online users, who conduct online searching, make online purchases. The low conversion rate seems to be correlated with poor usability aspect of most m-commerce applications and poor satisfaction reported by users. Research has reported that satisfaction and continuance intention in using m-commerce applications have relationships with service quality and information quality. In this study, a new model of user satisfaction and continuance intention in the context of mobile application was proposed by …

Activated Carbon Fixed-Bed Adsorber Design For Treating Chromium Hexavalent Wastewater, Tedi Hudaya, Velicia Rachmat

Makara Journal of Technology

Pollution caused by industrial wastewater containing heavy metals is a major issue, primarily due to its toxic nature. A cheap yet effective method to deal with such wastewater is activated carbon adsorption. The purpose of this research is to evaluate and design a fixed bed adsorber with granular activated carbon as an adsorbent to process wastewater-containing chromium hexavalent (Cr 6+). Experiments show that the Langmuir isotherm fits the equilibrium data as effectively as the Freundlich isotherm. Activated carbon used in this research is Jacobi 2000® derived from bituminous coal. The lab scale inlet volumetric flow is 100 mL/h with different …

Toward Building Resilient, Sustainable, And Smart Infrastructure In The 21st Century, Aly Mousaad Aly

Faculty Publications

In recent years, as a result of significant climate change, stringent windstorms are becoming more frequent than before. Given the threat that windstorms bring to people and property, wind/structural engineering research is imperative to improve the resilience of existing and new infrastructure, for community safety and assets protection. The Windstorm Impact, Science and Engineering (WISE) research program at Louisiana State University (LSU) focuses on creating new knowledge applicable to the mitigation of existing and new infrastructure, to survive and perform optimally under natural hazards. To achieve our research goals, we address two imperious challenges: (i) characterization of realistic wind forces …

Investigation Of Ship Hull Girder Strength With Grounding Damage, Muhammad Zubair Muis Alie, Ristiyanto Adiputra

Makara Journal of Technology

The objective of the present study is to investigate ship hull girder strength as a result of grounding damage upon longitudinal bending. A bulk carrier and tanker are analyzed and Smith’s Method is adopted and implemented in the analysis program. An efficient solution procedure is performed by assuming the cross-section remains plane and the vertical bending moment is applied to the cross section. As a fundamental case, the damage is simply created by removing the elements from the cross section. Welding residual stress, initial imperfections, and crack extensions are not considered. The grounding damage is made by two conditions, namely …

Internet Traffic Forecasting Model Using Self Organizing Map And Support Vector Regression Method, Enrico Laoh, Fakhrul Agustriwan, Chyntia Megawati, Isti Surjandari

Makara Journal of Technology

Internet traffic forecasting is one of important aspect in order to fulfill the customer demand. So, the service quality of internet service provider (ISP) can be maintained at the good level. In this study self organizing map (SOM) and support vector regression (SVR) algorithm are used as forecasting method. SOM is first used to decompose the whole historical data of traffic internet into clusters, while SVR is used to build a forecasting model in each cluster. This method is used to forecast ISPs traffic internet in Jakarta and surrounding areas. The result of this study shows that SOM-SVR method gives …

Satellite-Based Monitoring Of Spatiotemporal Changes In Batudulang Forest In Sumbawa, Indonesia, Mohammad Muslim, Arief Budhi Witarto, Wahyu Indrajaya

Makara Journal of Technology

Space-based earth observation technology applicable to forest inventory and monitoring is well known in the scientific community. High-resolution satellite images form an important data source for forest mapping and change detection at regional and national scales. The value of forest change information derived from remote sensing data is significantly enhanced if this information is integrated into a spatially explicit geographic information system. Satellite-based rapid assessment was conducted to measure spatiotemporal changes in Batudulang forest over the years. The general approach to quantify change in the spatial aspect of the forest involved change detection using moderate-resolution imaging spectro-radiometer satellite-based normalized difference …

Effects Of The Preheating Temperature On The Crystal Structure And Texture Of Martensitic Stainless Steel, Tri Hardi Priyanto, Rifai Muslih, Herry Mugirahardjo, Bharoto Bharoto, Andon Insani, Muzzakiy Muzzakiy

Makara Journal of Technology

Theoretically, the preheating temperature refers to the start martensite temperature (Ms), and the martensite transformation can be considered as the conservation of the invariant habit-plane in the lattice structure. The habit-plane is the interface plane between austenite and martensite as measured on a macroscopic scale. From the calculation, Ms = 252 °C. The martensite formation can be affected by temperature or stress treatment. In this experiment, temperature treatment was conducted. The sample was treated at 250 °C ± 10 °C. Before and after the pre-heat treatment, the sample was characterized using the neutron diffraction method. BATAN’s Texture Diffractometer (DN2) with …

Strength Structure Analysis Of Main Gate Graving Dock Using Pontoons For Condition Repairs, Budianto Budianto

Makara Journal of Technology

Main gate graving dock with pontoon type can certainly suffered some level of damage after a long period of operation. Many employments within the graving dock can delay the process repair of main gate. The main gate may not be opened, because employees are still working to ship fabrication process under sea waterline. For accommodate these interrelated conditions, the best solution with repair one side of the main gate with type pontoon and employees can still work ship fabrication process in graving dock conducted simultaneously. The repair process conditions must be required main gate structure that consists of only one …

Mapping Of Bruise Of Oil Palm Fresh Fruit Bunch During Loading And Transportation From Field To Mill, Andreas Wahyu Krisdiarto

Makara Journal of Technology

Fresh fruit bunches (FFBs) are used as raw materials for palm oil, and their transport from a field is a critical step to maintain their quality. Fruit integrity should be maintained so the mill can efficiently obtain palm oil with less than 5% free fatty acid content. Physical treatments for FFBs during loading to truck bins and transport may cause physical injuries. This research aimed to map fruit bruises. The map can be used as a basis in managing transport of FFBs. Physical injuries were assessed by bruise index (BI), which was calculated by measuring the bruise area and weight …

Benchmarking Product Service System Of Generator Set Distributors, Venny Violetta Tiurindah, Tanika Dewi Sofianti

Makara Journal of Technology

Power generation is an industry that is essential to sustain daily life and competes with generator set distributors. The product service system of distributors must be improved to survive the competition. This research aims to develop tools for benchmarking the product service system of generator set distributors. Benchmarking identifies gaps between a product and other competitors’ products. In this work, a product service system board is used to visualize the current product service system of a generator set distributor. A PPIAF framework and a SERVQUAL framework are adapted to assess product performance and service quality, respectively. AHP is used as …

Purdue Air Sense: A Methodology For Improving The Accuracy Of Ambient Aerosol Mass Concentration And Size Distribution Measurement With Low-Cost Optical Sensing Techniques, Rishabh Ramsisaria, Satya Sundar Patra, Brandon Emil Boor

The Summer Undergraduate Research Fellowship (SURF) Symposium

There is a global lack of a means for monitoring air pollutant levels at a local level due to expensive and bulky instrument requirements. It is important to monitor toxic gas levels, as well as particulate matter levels, in the atmosphere to study their effects on human health and to further develop city- and community-level air pollution solutions. In this study, with the means of a Raspberry Pi, low-cost Alphasense Optical Particle Counter and gas sensors, and methodical calibration techniques, we built a portable 3-D printed module powered by clean electricity generated by an on-board Voltaic solar cell that measures …

Microstructures And Hardness Of Tig Welded Experimental 57fe15cr25ni Steel, Parikin Parikin, Mohammad Dani, Abu Khalid Rivai, Agus Hadi Ismoyo, Riza Iskandar, Arbi Dimyati

Makara Journal of Technology

The microstructures and hardness of tungsten inert gas (TIG) welded experimental 57Fe15Cr25Ni steel were investigated through optical–scanning electron microscopy analyses and with a hardness tester, respectively. The welding process restructured the constituent atoms into regular and irregular crystal lattices. Rapid cooling of the weld metal allowed the formation of a dendritic (columnar) structure, with porous grains. By contrast, slow cooling influenced HAZ and led to the formation of grain structures. The crystal lattice became more organized and larger than other zones. Meanwhile, the base metal formed circular nets that covered large area inside thick and thin grain boundaries. The diffraction …

My Catalyst, Gabrielle Gambino Lyon

Celebration of Learning

Over the course of my internship and shadow program with Pepper Lawson Construction and Ziegler Cooper Architects, I was able to explore the various career paths involved in the design, construction, and civil engineering fields. My work on the construction site of a high-rise apartment building located in the heart of Houston, TX allowed me first-hand experience working and learning alongside project engineers, contractors, building developers, and the construction team.

This project was the perfect confluence of my main areas of interest: structural, mechanical, civil, and environmental engineering, as well as architecture. My daily work consisted of on-site walk throughs, …

Efficient Adjacency Queries And Dynamic Refinement For Meshfree Methods With Applications To Explicit Fracture Modeling, James Olliff

USF Tampa Graduate Theses and Dissertations

Meshfree methods provide a more practical approach to solving problems involving large deformation and modeling fracture compared to the Finite Element Method (FEM). However meshfree methods are more computationally intensive compared to FEM, which can limit their practicality in engineering. Meshfree methods also lack a clear boundary definition, restricting available visualization techniques. Determining particle locations and attributes such that a consistent approximation is ensured can be challenging in meshfree methods, especially when employing h-refinement. The primary objective of this work is to address the limitations associated with computational efficiency, meshfree domain discretization, and h-refinement, including both placement of particles as …

Preliminary Investigation Of Tensile Strength And Impact Characterization Of Cementitious Composite Incorporating Carbon Nanotubes, Robabeh Jazaei

UNLV Theses, Dissertations, Professional Papers, and Capstones

Cement has been largely used in the construction industry, specifically as a matrix for concrete. Recently, a new generation of cement-based composite that greatly increases mechanical properties is replacing conventional concrete. With periodic advances in the field, researchers considered particles with high-aspect ratios such as Carbon Nanotubes (CNTs) to reinforce cement matrices. Although there is not much literature to draw upon in research, some research on improving the tensile strength of cementitious composite incorporating with CNTs does exist. However, there had been no evidence of investigation into impact strength until this study.

Most papers presented examined the effect of multi-walled …

Hawai'i Wildlife Fund V. County Of Maui, Lowell J. Chandler

Public Land & Resources Law Review

In Hawai’i Wildlife Fund v. County of Maui, the Ninth Circuit held that the plain language of the Clean Water Act provides jurisdiction over indirect discharges of pollutants from a point source into groundwater that is shown to be connected to navigable waters. The court found that studies confirmed pollutants entering the Pacific Ocean were fairly traceable to the County of Maui’s sewage disposal wells. In affirming the district court’s ruling, the Ninth Circuit held that Maui County violated the Clean Water Act by discharging pollutants into a navigable water without the required permit. The court also concluded the …

Small-Signal-Stability Enhancement Using A Power-System Stabilizer Based On The Cuckoo-Search Algorithm Against Contingency N-1 In The Sulselrabar 150-Kv System, Muhammad Ruswandi Djalal, Muhammad Yusuf Yunus, Herlambang Setiadi, Awan Uji Krismanto

Makara Journal of Technology

Small-signal stability is one of the main factors limiting power transmission in conventional power systems. This concern is primarily handled by adding damper windings of a synchronous generator and power-system stabilizer (PSS). However, due to the impact of the N-1 contingency, damper windings and a conventional PSS are insufficient to overcome this problem. Proper placement and design of the PSS are crucial for improving stability. One approach to optimizing the placement and tuning of the PSS is to use an artificial-intelligence method. Here, the cuckoo-search algorithm (CSA) is proposed to optimize the PSS tuning and placement. Based on simulation, it …

Prerequisites For Public Acceptance Of Waste-To-Energy Plants: Evidence From Germany And Indonesia, Uwe Lahl, Barbara Zeschmar-Lahl

Makara Journal of Technology

Construction of waste incinerators often encounters resistance from the public. The minimum requirements for the ac- ceptance of these installations include modern air pollution control (APC) technology and safe disposal of residues. Confidence in the statements of government and government agencies as well as on those who support is an important point of acceptance. Independent scientific bodies such as universities can help to make this happen. In the case of the installation of waste into energy (WtE), such scientific support can be the measurement of emissions and their evalua- tion. Many products that enter the waste stream contain heavy metals, …

Hybrid Brain-Computer Interface: A Novel Method On The Integration Of Eeg And Semg Signal For Active Prosthetic Control, Reza Darmakusuma, Ary Setijadi Prihatmanto, Adi Indrayanto, Tati Latifah Mengko

Makara Journal of Technology

This paper describes a novel method for controlling active prosthetics by integrating surface electromyography (sEMG) and electroencephalograph signals to improve its intuitiveness. This paper also compares the new method (RTA-2) with other existing methods (AND and OR) for controlling active prosthetics. Based on analysis, RTA-2 features higher true positive rate (TPR) and balanced accuracy (BA) than AND method. On the other hand, the new method (RTA-2) yields lower false detection rate (FPR) than OR method. Analysis also shows that RTA-2 possesses equal TPR, FPR, and BA with the detection of movement intention using sEMG-based system. Although the RTA-2 method shows …

An Exploratory Study Of Sukuk Utilisation For Transportation Infrastructure Development In Indonesia, Fiona Lamari, Ayomi Dita Rarasati, Meilia Evita

Makara Journal of Technology

Investment in infrastructure is one of the principal drivers of the growth of the economy. For that reason, the Indonesian government has proposed an investment budget in the railway and sea and air transport sectors over the next 10 years. In order to overcome the burden of direct outflows and for the future, a study was conducted to lay down the framework of Shariah-compliant payments for the development of infrastructure in Indonesia in the transport sector. This paper aims to explore the opportunity and implementation of sukuk utilisation to develop transportation infrastructure. Secondary data study and interviews were selected for …

Seismic Response Analysis Along The Coastal Area Of Bengkulu During The September 2007 Earthquake, Lindung Zalbuin Mase

Makara Journal of Technology

A strong earthquake of 8.4 Mw occurred at the Sumatra Subduction Zone in September 12, 2007. The area that underwent the impact of the earthquake was located along the coastal area of the Bengkulu Province. A seismic ground response study was then performed with reference to the event. Several site investigations, including standard penetration test and shear wave velocity tests, were conducted to understand the subsoil condition. The data were used to analyze a ground response during the earthquake. The amplification factor of each site was obtained, and a comparison of the spectral accelerations was performed. The results showed that …

Structural And Photoluminescence Properties Of Zno Thin Films Deposited By Ultrasonic Spray Pyrolysis, Iwan Sugihartono, Erfan Handoko, Vivi Fauzia, Artoto Arkundato, Lara Permata Sari

Makara Journal of Technology

Zinc oxide (ZnO) thin films on a silicon (Si) (111) substrate were grown herein using ultrasonic spray pyrolysis at 450 °C with different Zn concentrations. The ZnO thin films had X-ray diffraction patterns of a polycrystalline hexagonal wurtzite structure. The (002) and (101) peak intensities changed under different Zn concentrations. Furthermore, according to Scherer's and Stokes–Wilson equations, the crystallite size and the internal strain of the ZnO thin films in the (002) and (101) peaks changed with the Zn concentration. Optically, the photoluminescence spectra indicated that the ratio of the UV/GB emission of the ZnO thin films was the highest …

Isolation And Molecular Weight Characterization Of Tetragonula Laeviceps Honey Protein, Muhamad Sahlan, Nurul Azizah, Kazuaki Hakamada, Keiichi Noguchi, Masafumi Yohda

Makara Journal of Technology

The concentration of protein in honey is lower than polysaccharide. However, recently the honey’s protein is intensively studied and it showed that protein also have several biological activities such as antibacterial activity. The purpose of this research is to isolate and characterize Tetragonula laeviceps honey protein by determining the molecular weight. Honey protein of Trigona laeviceps was isolated using ultra-filtration with the membrane’s size of 30 kDa, then concentrated using tube membrane size 10 kDa. Molecular weight was analyzed by SDS PAGE. From the analysis, there was major protein band in honey produced by Tetragona laeviceps identified. The produced molecular …

Coax-Fed Dipole-Type Applicator For Hepatic Cancer Rf Ablation, Basari Basari, Aditya Rakhmadi, Kazuyuki Saito

Makara Journal of Technology

Cancer is the third leading cause of mortality in the world and is one of the most difficult diseases to detect and cure. This fact motivates us to investigate a treatment method by using radiofrequency (RF) ablation. RF ablation therapy kills cancer cells by electromagnetically heating them up. The treatment uses an applicator that is inserted into the body to heat the cells. The cancer cells are exposed to a temperature of more than 60 °C in short duration (a few seconds to a few minutes), thereby causing cell destruction locally. To ensure effective treatment, a minimally invasive method is …