Mechanical Engineering Commons^™

Passive Radiative Cooling By Spectrally Selective Nanoparticles In Thick Film Nanocomposites, David Allen Young

USF Tampa Graduate Theses and Dissertations

Passive cooling of buildings is a benefit to society since no energy input is required for space cooling which reduces electricity consumption, fossil fuel burning, and greenhouse gas emissions. When a passive cooling technology radiates heat from the earth through the atmospheric windows to space higher levels of cooling power are possible -- this phenomenon is classified as passive “radiative” cooling. Spectrally selective surface coatings provide radiative cooling to lower surface temperatures by reflecting most solar radiation, while emitting infrared radiation at wavelengths between 8-13 μm through the primary atmospheric window to the cold of space. Multiple applications of radiative …

Estimating The As-Placed Grout Volume Of Auger Cast Piles, Tristen Mee

USF Tampa Graduate Theses and Dissertations

Augered Cast-in-Place (ACIP) piles are a geotechnical foundation element increasingly used to support large publicly funded structures as an alternative to drilled shafts or driven piles. ACIP piles are constructed by drilling an excavation to the full length of the designed pile with a continuous flight auger. Grout (cement, sand, and water mixture) is then pumped through the hollow auger stem to begin grouting the excavation. After establishing an initial head pressure, the auger is slowly extracted while the remainder of the pile is grouted. Once the auger is completely removed, the steel reinforcement cage is lowered into the grouted …

Device For Imaging Cross-Section Of Post-Tensioned Structural Tendons In The Field, David Dukeman

USF Tampa Graduate Theses and Dissertations

With increasing use of grouted post-tensioned tendons in structures, there is a critical need for equipment to determine deficient grouting. Inadequate grouting can cause dangerous corrosion of the high-strength post-tensioning steel in the tendons. Evaluation should be non-destructive, and early detection is needed to take timely remedial actions to repair or replace any tendons that are affected before catastrophic failure occurs. In particular, there is need for an imaging method that shows the cross-section of the tendon being tested and flag any deficiencies present relative to the location of the strands in the cross section. The method should be rapid, …

Efficient Adjacency Queries And Dynamic Refinement For Meshfree Methods With Applications To Explicit Fracture Modeling, James Olliff

USF Tampa Graduate Theses and Dissertations

Meshfree methods provide a more practical approach to solving problems involving large deformation and modeling fracture compared to the Finite Element Method (FEM). However meshfree methods are more computationally intensive compared to FEM, which can limit their practicality in engineering. Meshfree methods also lack a clear boundary definition, restricting available visualization techniques. Determining particle locations and attributes such that a consistent approximation is ensured can be challenging in meshfree methods, especially when employing h-refinement. The primary objective of this work is to address the limitations associated with computational efficiency, meshfree domain discretization, and h-refinement, including both placement of particles as …

Dns And Les Of Scalar Transfer Across An Air-Water Interface During Inception And Growth Of Langmuir Circulation, Amine Hafsi

USF Tampa Graduate Theses and Dissertations

Direct numerical simulations (DNS) of an initially quiescent coupled air-water interface driven by an air flow with free stream speed of 5 m/s have been conducted. The DNS solves a scalar advection-diffusion equation for dissolved gas (or scalar) concentration in order to determine the impact of the water-side turbulence on scalar (mass) transfer from the air side to the water side and subsequent vertical transport in the water column. Two simulations are compared: one with a freely deforming interface and a second one with a flat interface. In the first simulation, the deforming interface evolves in the form of gravity-capillary …

Corrosion Of Steel In Submerged Concrete Structures, Michael Thomas Walsh

USF Tampa Graduate Theses and Dissertations

This investigation determined that severe corrosion of steel can occur in the submerged portions of reinforced concrete structures in marine environments. Field studies of decommissioned pilings from actual bridges revealed multiple instances of strong corrosion localization, showing appreciable local loss of steel cross-section. Quantitative understanding of the phenomenon and its causes was developed and articulated in the form of a predictive model. The predictive model output was consistent with both the corrosion rate estimates and the extent of corrosion localization observed in the field observations. The most likely explanation for the observed phenomena that emerged from the understanding and modeling …

Numerical Simulation Of Flow In Ozonation Process, Jie Zhang

USF Tampa Graduate Theses and Dissertations

In the last two decades, Computational Fluid Dynamics (CFD) has shown great potential as a powerful and cost-efficient tool to troubleshoot existing disinfection contactors and improve future designs for the water and wastewater treatment utilities.

In the first part of this dissertation two CFD simulation methodologies or strategies for computing turbulent flow are evaluated in terms of the predicted hydraulic performance of contactors. In the LES (large eddy simulation) methodology, the more energetic, larger scales of the turbulence are explicitly computed or resolved by the grid. In the less computationally intensive RANS (Reynolds-averaged Navier-Stokes) methodology, only the mean component of …

Towards Rans Parameterization Of Vertical Mixing By Langmuir Turbulence In Shallow Coastal Shelves, Nityanand Sinha

USF Tampa Graduate Theses and Dissertations

Langmuir turbulence in the upper ocean is generated by the interaction between the wind-driven shear current and the Stokes drift velocity induced by surface gravity waves. In homogenous (neutrally stratified) shallow water, the largest scales of Langmuir turbulence are characterized by full-depth Langmuir circulation (LC). LC consists of parallel counter-rotating vortices aligned roughly in the direction of the wind. In shallow coastal shelves, LC has been observed engulfing the entire water column, interacting with the boundary layer and serving as an important mechanism for sediment re-suspension.

In this research, large-eddy simulations (LES) of Langmuir turbulence with full-depth LC in a …

Minimal And Symmetric Global Partition Polynomials For Reproducing Kernel Elements, Mario Jesus Juha

USF Tampa Graduate Theses and Dissertations

The Reproducing Kernel Element Method is a numerical technique that combines finite element and meshless methods to construct shape functions of arbitrary order and continuity, yet retains the Kronecker-δ property. Central to constructing these shape functions is the construction of global partition polynomials on an element. This dissertation shows that asymmetric interpolations may arise due to such things as changes in the local to global node numbering and that may adversely affect the interpolation capability of the method. This issue arises due to the use in previous formulations of incomplete polynomials that are subsequently non-affine invariant. This dissertation lays out …

Physically Meaningful Harmonization Of Tire/Pavement Friction Measurement Devices, Madhura Priyanga Nishshanke Rajapakshe

USF Tampa Graduate Theses and Dissertations

Accurate characterization and evaluation of tire/pavement friction is critical in assuring runway and highway safety. Historically, Pavement Friction Measurement Devices (PFMDs) employing different measuring mechanisms have been used to evaluate tire/pavement friction. They yield significantly disparate friction coefficients under the same contact conditions. Currently, an empirically developed data harmonization method based on a reference device (Dynamic Friction Tester (DFT)) is used in an attempt to overcome the disparities between the measurements using various different PFMDs. However, this method, which has been standardized by the American Society for Testing and Materials (ASTM E1960), has been criticized for its inconsistency by researchers …