Engineering Commons^™

New Optimal High Efficiency Dsp-Based Digital Controller Design For Super High-Speed Permanent Magnet Synchronous Motor, Limei Zhao

Electronic Theses and Dissertations

This dissertation investigates digital controller and switch mode power supply design for super high-speed permanent magnet synchronous motors (PMSM). The PMSMs are a key component for the miniaturic cryocooler that is currently under development at the University of Central Florida with support from NASA Kennedy Space Center and the Florida Solar Energy Center. Advanced motor design methods, control strategies, and rapid progress in semiconductor technology enables production of a highly efficient digital controller. However, there are still challenges for such super high-speed controller design because of its stability, high-speed, variable speed operation, and required efficiency over a wide speed range. …

Power And Memory Optimization Techniques In Embedded Systems Design, Atef Khalil Allam

LSU Doctoral Dissertations

Embedded systems incur tight constraints on power consumption and memory (which impacts size) in addition to other constraints such as weight and cost. This dissertation addresses two key factors in embedded system design, namely minimization of power consumption and memory requirement. The first part of this dissertation considers the problem of optimizing power consumption (peak power as well as average power) in high-level synthesis (HLS). The second part deals with memory usage optimization mainly targeting a restricted class of computations expressed as loops accessing large data arrays that arises in scientific computing such as the coupled cluster and configuration interaction …

Multispectral Camera Control And High Speed Image Transfer Using Lossless Hardware Compression, Padraig Ryan

Theses

This work provides extensions of a standard D-Cam/Firewire digital camera platform for use within a multispectral imaging setting and includes real-time lossless image compression targeted at the re-configurable environment of an FPGA. The control and image acquisition structures specific to multispectral systems are detailed with respect to an embedded firmware solution, complementary host PC software driver routines, and camera hardware control infrastructures. The augmentation of the standards based implementation is discussed without compromising compliance with underlying specifications. The mandate for image data acquisition includes glue logic to efficiently transmit data via a high-speed communications pipe, IEEE - 1394 in this …

Automated Control Of Led-Based Illumination Using Image Analysis Metrics, Stephen Mills

Theses

This project discusses a microprocessor controlled illumination system that covers the visible spectrum. It uses multiple discrete wavelength LEDs. Spatial and spectral illumination profiles are achieved by controlling LED currents with an array of voltage controlled current sources. A highly efficient polycarbonate holographic diffuser is used to improve the uniformity of the distribution. System design is underpinned by accurate characterisation and modelling of the LEDs used.

Image analysis techniques are then used to parameterise the recorded scene and to provide a figure of merit for the quality of the illumination. Several functions such as contrast, low/high saturation, average brightness and …

An Evaluation Of Model-Based Predictive Control, Daniel Czarkowski

Theses

This thesis attempts to determine whether advanced control algorithms offer any real benefits to the process industry in terms of optimising single-input single output process units. To establish this, an ideal PID controller, Two Degree of Freedom (2 DOF) PID Controller and the Generalised Predictive Controller (GPC) are compared. A common design philosophy is applied based on optimising performance subject to constraints on robustness. Specifically, three different designs are examined; minimum subject to constraints on the gain and phase margin, minimum lAE subject to constraints on the modulus margin and minimum lAE subject to constraints on the input sensitivity function. …

Real-Time Multi-Spectral Image Processing On The Adsp-Bf533 Dsp, Stephen Niall Coffey

Theses

As the need to process multi-spectral images in real-time is becoming more prevalent, the pressure on Integrated Circuit (IC) manufacturers to produce cheap and reliable devices capable of handling the demands of such operations is growing. This project investigates the ADSP-BF533 Blackfin® Digital Signal Processor (DSP) and its ability to support a real-time multi-spectral imaging system. The Blackfin® DSP, incorporating the Analog Devices/Intel Micro Signal Architecture (MSA), are a broad family of 16-bit fixed-point product with a dual Multiply Accumulate (MAC) core.

Using the MicroC/OS-II Real-time Operating System (RTOS), which is a completely portable and scaleable pre-emptive real-time kernel, the …

Characterisation, Modelling And Performance Evaluation Of Cmos Integrated Rf-Mems Multielectrode Tunable Capacitor, Zbigniew Olszewski

Theses

The circuits used in telecommunications are made of two types of components; active integrated circuits that have continuously been improved together with the evolution of the Si technology and off-chip and on-chip passive components. The latter did not profit from much development and now constitute the bottleneck for further integration of RF (Radio Frequency) integrated circuits. MicroElectroMechanical Systems (MEMS) is rapidly emerging as an enabling technology to yield a new generation of high performance components to replace off-chip (not integrated) and on-chip (poor performance) counterparts. The RF components (RF-MEMS) that can be fabricated with MEMS technology are mainly the resonator, …

Controller Design And Web-Based Simulation For A Pasteurisation Process, Luis Torres

Theses

The basic PID controller remains the most commonly used automatic feedback control technique in industry. Many tuning techniques exist for this controller and the use of tuning rules remains very popular, both in industry and academia. This thesis is concerned with the practical evaluation of a selected number of PID tuning rules. The rules were to be evaluated on an industrial pilot-scale milk pasteurisation process. However, most of these rules could not be tested on the real plant as the industrial distributed control system was quite inflexible and did not permit many of the more advanced PID structures e.g. two-degree …

A 10-Bit 100msample/S Pipeline Analog- To-Digital Converter In Cmos, Pieter Berkelaar

Theses

High speed, medium resolution ADC’s, are required for many applications, including wireless receivers, ultrasound systems, wireline interfaces, cameras and camcorders. Low power dissipation is important, particularly for portable equipment where battery life must be maximised. The pipeline ADC architecture is particularly suited to such applications. Its strength comes from the manner in which it performs a conversion, distributing the work in time and amongst successive stages. These stages operate concurrently, maintaining high throughput. Each stage is made up of a fully differential switched capacitor sample-and- hold amplifier and some other circuitry. Designing these circuits to operate at l00MHz is extremely …

Robust Colour Segmentation Under Dynamic Lighting Conditions, Noreen Mary Looney

Theses

Traditionally, the issue of colour constancy has limited the success of colour image segmentation algorithms. Numerous methods exist to achieve colour constancy for different applications. The principal contribution of this thesis is the investigation of a suitable technique for the problem of robust colour based object detection.

Appropriate colour models are investigated and analysed in order to assess their ability to enhance the isolation process. Models that possess suitable colour constancy characteristics are chosen for use with image segmentation algorithms. Reviews of existing sur\'eys of image segmentation algorithms are appraised for the emergence of a suitable colour image segmentation technique. …

Heuristics For Offset Assignment In Embedded Processors, Satya Swaroop Mahapatra

LSU Master's Theses

This thesis deals with the optimization of program size and performance in current generation embedded digital signal processors (DSPs) by the design of optimal memory layouts for data. Given the tight constraints on the size, power consumption, cost and performance of these processors, the minimization of code size in terms of the number of instructions required and the associated reduction in execution time are important. Several DSPs provide limited addressing modes and the layout of data, known as offset assignment, plays a critical role in determining the code size and performance. Even the simplest variant of the offset assignment problem …

Traffic Engineering And Path Protection In Mpls Virtual Private Networks, Pooja S. Aniker

LSU Master's Theses

Traffic Engineering (TE) attempts to establish paths for the flow of data in a network so as to optimize the resource utilization and maximize the network performance. One of the main goals of Traffic Engineering is to bring about efficient and reliable network operations. Constraint based routing is the key to Multiprotocol label switching TE. Constraint based routing helps to manage traffic paths within a MPLS network and allows for traffic to flow along certain desired paths. MPLS also supports explicit routing thus providing TE capabilities. MPLS TE enables resiliency and reliability to be built into networks, thus increasing the …

Remote Power Delivery For Hybrid Integrated Bio-Implantable Electrical Stimulation System, Venkat Reddy Gaddam

LSU Master's Theses

Bio-implantable devices such as heart pacers, gastric pacers and drug-delivery systems require power for carrying out their intended functions. These devices are usually powered through a battery implanted with the system or are wired to an external power source. In this work, a remote power delivery system (RPDS) is considered as a means to charge rechargeable batteries that power a Bio-implanted Electrical Stimulation System (BESS). A loosely coupled inductive power transmitter and receiver system has been designed to recharge batteries for a bio-implanted gastric pacer. The transmitter coil is periodically worn around the waist. The receiver coil, rechargeable batteries, battery-charging …

Cad Model Extraction Of Pcb Signal Discontinuity Using A Circuit Extraction Approach Based On Mixed-Potential Integral Equation Formulation, Shaofeng Luan

Doctoral Dissertations

"In high-speed digital design, signal via transitions on printed circuit boards (PCBs) are becoming an important signal integrity issue. Efficient and accurate models for via transitions are necessary to analyze high bit-rate digital circuit system. The circuit extraction approach based on a mixed-potential integral equation formulation (CEMPIE) is an extension of the Partial Element Equivalent Circuit approach (PEEC) to general multi-layered media. CEMPIE was further developed to include the horizontal current components on the vertical surface and extended to model the discontinuities on multilayer PCBs. A procedure of building SPICE models for signal via transitions between printed circuit board layers …

Blind Multiridge Detection And Reconstruction Using Ultrasonic Signals, Rekha Katragadda

LSU Master's Theses

Time-frequency signal analysis has been widely applied in the modern radar, acoustic, sonar and ultrasonic signal processing techniques. Recently, the nondestructive testing (NDT) techniques via the ultrasonic instrumentation have shown the striking capability of the quality control for the material fabrication industry. In this thesis, we first provide a general mathematical model for the ultrasonic signals collected by pulse-echo sensors and then design a totally blind, novel, signal processing NDT technique relying on neither a priori signal information nor any manual effort. The signature signal can be blindly extracted by using the automatic optimal frame size selection for further modeling …

Development Of Process Techniques For Bistable Microbeam Fabrication, Varsha Francis

LSU Master's Theses

A design which uses bistable beams to modulate light is suggested in this thesis and appropriate processing techniques are presented. A beam when placed under compression above the Euler limit has two stable states. The compression in an electroplated beam can be controlled by the plating current density of nickel during electrodeposition. This beam is attached to an electromechanical comb. Voltages applied to the combs cause the beam to snap from one stable state to another. Structures were designed with dimensions that gave feasible voltages, snap distances, compressions required to snap. A two mask process was used for the fabrication …

A Study On The Nature Of Anomalous Current Conduction In Gallium Nitride, Joshua K. Spradlin

Theses and Dissertations

Current leakage in GaN thin films limits reliable device fabrication. A variety of Ga and N rich MBE GaN thin films grown by Rf, NH3, and Rf+ NH3, are examined with electrical measurements on NiIAu Schottky diodes and CAFM. Current-voltage (IV) mechanisms will identify conduction mechanisms on diodes, and CAFM measurements will investigate the microstructure of conduction in GaN thin films. With CAFM, enhanced conduction has been shown to decorate some extended defects and surface features, while CAFM spectroscopy on a MODFET structure indicates a correlation between extended defects and field conduction behavior at room temperature. A remedy for poor …

Investigation Of Surface States And Device Surface Charging In Nitride Materials Using Scanning Kelvin Probe Microscopy, Mohammed Shahriar Sabuktagin

Theses and Dissertations

In this work Scanning Kelvin Probe Microscopy (SKPM) was used to characterize surface states and device surface charging in nitride materials. Samples grown by Molecular Beam Epitaxy (MBE), Metal Organic Chemical Vapor Deposition (MOCVD) and Hydride Vapor Phase Epitaxy (HVPE) typically show a high surface band bending of about 1 eV. In an n-type sample with 3X1017 cm-3 carrier concentration, 1 eV upward band bending corresponds to 1.7X1012 cm-2 trapped charge density in the surface states. Under continuous ultraviolet (UV) illumination up to 0.6 eV surface photo voltage effect could be observed in some samples, which further indicates that surface …

Factors Effecting Field Emission From Multiwalled Carbon Nanotubes, Abhilash Krishna

LSU Master's Theses

Carbon nanotubes (CNT) have emerged to be one of the most versatile of materials ever discovered. The small dimensions, high electrical conductivity and strength along with other physical and electrical properties make them a unique material with a wide range of promising applications. One such use is that of CNTs as electron beam sources. A typical CNT has a diameter of only a few nanometers but can be hundreds of microns long. Applying a voltage across the length of such an object results in field emission of electrons from one end of the tube. This effect is due to intense …

Interference Suppression And Parameter Estimation In Wireless Communication Systems Over Time-Varing Multipath Fading Channels, Jianqiang He

LSU Doctoral Dissertations

This dissertation focuses on providing solutions to two of the most important problems in wireless communication systems design, namely, 1) the interference suppression, and 2) the channel parameter estimation in wireless communication systems over time-varying multipath fading channels. We first study the interference suppression problem in various communication systems under a unified multirate transmultiplexer model. A state-space approach that achieves the optimal realizable equalization (suppression of inter-symbol interference) is proposed, where the Kalman filter is applied to obtain the minimum mean squared error estimate of the transmitted symbols. The properties of the optimal realizable equalizer are analyzed. Its relations with …

High-Freequency Cmos Vlsi Chip Testability And On-Chip Interconnect Modeling, Evan Ross Shultz

LSU Master's Theses

As high-speed digital and radio-frequency mixed-signal integrated circuits become increasingly common in product designs in industry, it is important for VLSI designers to be familiar with the challenges of chip testing and the behavior of circuit elements, including on-chip interconnect, at high frequencies. Expensive, specialized test equipment and software simulation packages for high-frequency chip testing and design are not always accessible for student research. This thesis documents the setup and characterization of a best-possible environment for high-frequency chip testing and data acquisition using existing laboratory equipment and resources. Experimental methodologies and measurement results of on-chip interconnect signal integrity and delay, …

A Programmable Cmos Decimator For Sigma-Delta Analog-To-Digital Converter And Charge Pump Circuits, Raghavendra Reddy Anantha

LSU Master's Theses

PROGRAMMABLE DECIMATOR FOR SIGMA-DELTA ANALOG-TO-DIGITAL CONVERTER: In this work a programmable decimator design has been presented in 1.5 μm n-well CMOS process for integration with an existing modulator to form a sigma-delta analog-to-digital converter (ADC). The decimator is implemented using a second order Cascaded Integrator Comb (CIC) filter and can be programmed to work with two different oversampling ratios of 64 and 16. The input to the decimator is provided from a first order modulator. With oversampling ratios of 64 and 16, an output resolution of 10-bit and 7-bit, respectively are achieved for the ADC. The ADC can be operated …

Comparative Analysis Of Conventional And Ici-Self-Cancellation Digital Video Broadcasting Transceivers, Khaled Z. Matarneh

LSU Master's Theses

Digital video broadcasting–terrestrial (DVB-T) is one of the important technologies in the communication area because of its capability of high data-rate multimedia transmission. Orthogonal frequency division multiplexing (OFDM) has been the backbone technique in the current DVB-T systems adopted by Europe and Japan. However, since the OFDM system is very sensitive to the frequency synchronization and phase errors, which will induce the intercarrier interference (ICI), the ongoing research has been dedicated to this ICI problem in the presence of the Doppler frequency drift and the fading channels. A means to deal with the ICI problem is called the ICI self-cancellation …

Contact Effects In Thermally Evaporated Pentacene Thin Films And Aspects Of Microsystem Hybrid Integration, Jagadish Yernagula

LSU Master's Theses

Organic thin film transistors have the potential to replace silicon based transistors in applications such as smart cards and RF-ID due to their low cost and low processing temperatures. Thermally evaporated pentacene is studied as an organic thin film material. Thin film transistors were fabricated in bottom contact structure using thermal evaporation of pentacene at a rate of 0.5 to 1 nm/s. Heavily doped Si was used as a gate material and 100 nm thick silicon dioxide was used as a dielectric. Ni was used as contact metal for source and drain contacts. Threshold voltage of 16 V and mobility …

Mapping Weak Multidimensional Torus Communications On Optical Slab Waveguides, Karthik Sethuraman

LSU Master's Theses

This thesis deals with the mapping of communication of a d-dimensional weak torus on an optical medium. Our results are derived in the setting of a sawtooth slab waveguide. The mapping aims to reduce the number and cost of optical components, by exploiting the fact that not all edges of a weak topology are used simultaneously. This approach allows for a better utilization of the huge bandwidth of an optical slab waveguide; currently the cost and size of optical components external to the optical communication medium are the primary bottleneck of an optical interconnect. We introduce the notion of adjacency …

Fuzzifying [Sic] Markov Decision Process, Ahmed Syed Irshad

LSU Master's Theses

Markov decision processes have become an indispensable tool in applications as diverse as equipment maintenance, manufacturing systems, inventory control, queuing networks and investment analysis. Typically we have a controlled Markov chain on a suitable state space in which transitional probabilities depend on the policy (or decision maker) which comes from a set of possible actions. The main problem of interest would be to find an optimal policy that minimizes the associated cost. Linear Programming has been widely used to find the optimal Markov decision policy. It requires solutions of large systems of simultaneous linear equations. By the fact that the …

Improved Watermarking Scheme Using Decimal Sequences, Naveed Shaik Ashfaq

LSU Master's Theses

This thesis improves upon the work carried out by Mandhani on decimal sequence watermarking showing that the embedding and decoding algorithms used by Mandhani are not robust. We next specify improvements to these algorithms so that the peak signal to noise ratio (PSNR) is maximized and the distortion introduced in the image due to the embedding is minimized. By exploiting the cross correlation property of decimal sequences, the concept of embedding more than one watermark in the same cover image has been investigated. A comparison between the PSNRs for decimal sequence watermarking and other pseudorandom sequences has been made.

A Robust Noise Spectral Estimation Algorithm For Speech Enhancement In Voice Devices, Brett Joseph Chessher

LSU Master's Theses

In this thesis, a new robust noise spectral estimation algorithm is proposed for the purpose of single-microphone speech enhancement. This algorithm can generate the optimal noise spectral estimates in the Minimum Mean Square Error (MMSE) sense based on the speech statistics in the noisy environments. Compared to the well-adopted conventional noise spectral estimation method using the single-pole recursion, our proposed scheme is more reliable since the recursion coefficients are adaptable and optimal in the MMSE therein. We also propose a new accurate Resulting Signal-to-Noise Ratio (R-SNR) estimator as a quality measure to benchmark the existing noise spectral estimation techniques. This …

Wafer Level Chip Scale Packaging Using Wafer Bonder, Kailash Upadhyaya

LSU Master's Theses

An in-house processing capability is developed in this research for silicon-glass bonding for microfabrication and wafer level chip scale packaging (WLCSP) using a wafer bonder. New masking technology for wet etching of glass to a depth of more than 430 µm is reported in this research work along with development of an anodic bonding process that permits electrical feedthroughs for connections to outside world. Three novel masks were developed in this work for deep wet etching of glass. They were multilayers of metals Mo/Cr/Au (mask 1) and Cr/Au/electroplated Ni (mask 2) both in combination with 20 µm thick AZ® P4620 …

Ternary Logic To Binary Bit Conversion Using Multiple Input Floating Gate Mosfets In 0.5 Micron N-Well Cmos Technology, Sowmya Subramanian

LSU Master's Theses

In the present work, a CMOS ternary to binary bit conversion technique has been proposed using multiple input floating gate MOSFETs. The proposed circuit has been implemented in 0.5 µm n-well CMOS technology. The ternary input signals of {-1, 0, +1} are represented as -3 V, 0 V and +3 V, respectively. The ternary input is given as a combination of any two of the three voltage levels and the 4-bit binary output is generated in which the left most bit is sign bit (SB) followed by most significant bit (MSB), second significant bit (SSB) and the least significant bit …