Physical Chemistry Commons^™

Effects Of Kscn On Kinetic Characters Of The Positive Couple And Performance For Vanadium Redox Flow Battery, Jian-Guo Liu, Dong Shi, Yue Men, Chuan-Wei Yan

Journal of Electrochemistry

In order to improve the reaction activity of VO²⁺/VO²⁺ and the battery performance of Vanadium redox flow battery,different concentration of potassium sulfocyanates KSCN were added into 0.1mol/L VOSO₄/ H₂SO₄ solution,and the kinetic characters of electrochemical reaction of VO²⁺/VO²⁺ was studied by CV and EIS.The results showed that the addition of KSCN could improve the oxidative peak current value of positive couple VO²⁺/VO²⁺ reaction,but had little influence in the reductive peak.The addition of KSCN decreased the impedance at 1.0 V.And the value of standard rate constant k0 …

Effect Of Impurity Cu(2+) On Oxygen Electrode In Pemfc, Xiao Jie, Jun-Bo Hou, Zhi-Gang Shao, Bao-Lian Yi

Journal of Electrochemistry

Rotating disk electrode was adopted in this paper to simulate the cathode in PEMFC.In the Cu²⁺ electrolyte,the influence of impurity Cu²⁺ on Carbon-Supported Pt Catalysts was investigated by using electrochemical measurements such as chronocoulometry,cyclic voltammetry and linear sweep.Experimental results showed that,after constant voltage at 0.49 V,the ECA of Pt/C decreased dramatically,it's perhaps under potential deposition of Cu might occur on the substrate.Meanwhile the change of ORR Tafel scope reaction is very large.It might be because oxygen adsorption sites are occupied by Cu atoms after they under potential deposit on surface of Pt/C catalyst,and the adsorption of oxygen on …

Electro-Oxidation Of Methanol On Fe-Doped Pt-Zro2/C Catalyst, Mao-Cai Lin, Dong-Dong Liu, Qing-Chun Yu, Ming-Ruo Hu, Heng-Yong Tu

Journal of Electrochemistry

The Fe-doped ZrO₂ powders were prepared by so-gel method.After that,Pt-Zr_1-xFe_xO₂/C catalysts were made by reducing platinum salts with ethylene glycol.The physical property of the catalyst was characterized by XRD and TEM.It was found that the distribution of the catalyst was narrow,the particle sizes of Pt and ZrO₂ particles were 2~4 nm and 3~7 nm,respectively.The Cyclic Voltammetry and Chronoamperometry testing indicated that the electro-catalytic activity for methanol electro-oxidation on Pt-ZrO₂/C catalyst increased when ZrO₂ was doped with Fe.And Pt-Zr_0.95Fe_0.05O₂/C catalyst showed the highest activity …

Computational Study Of Pristine And Titanium-Doped Sodium Alanates For Hydrogen Storage Applications, Gopi Krishna Phani Dathar

Doctoral Dissertations

The emphasis of this research is to study and elucidate the underlying mechanisms of reversible hydrogen storage in pristine and Ti-doped sodium aluminum hydrides using molecular modeling techniques. An early breakthrough in using complex metal hydrides as hydrogen storage materials is from the research on sodium alanates by Bogdanovic et al., in 1997 reporting reversible hydrogen storage is possible at moderate temperatures and pressures in transition metal doped sodium alanates. Anton reported titanium salts as the best catalysts compared to all other transition metal salts from his further research on transition metal doped sodium alanates. However, a few questions remained …

Preparation And Performance Of Co And La Co-Doped Li-Rich Lithium Manganate, Da-Qiao Zhou

Journal of Electrochemistry

The cathode material of Li_1.1Co_0.02La_0.01Mn₂O₄ was successfully synthesized by the method of co-precipitation followed by a solid state reaction.In the sintering temperature range of 700～850 ℃,X-ray diffraction(XRD) results showed a single phase of each material and the increase of crystallization degree,and scanning electron microscopic(SEM) images indicated that the particle size increased and the specific surface area decreased,respectively,with increasing the sintering temperature.Due to its lower polarization resistance,the Co and La co-doped lithium-rich lithium manganate(sintered at 800 ℃) positive electrodes showed the most promising electrochemical performance.The capacity retention after 50 cycles reached 98.5%.

Electrochemical Properties Of Functionalized Carbon Nanotubes And Their Applications In Analysis Of 6-Mercaptopurine, Bao-Yi Lu, Yan-Yan Lai, Hong Li

Journal of Electrochemistry

The electrochemical behaviors and adsorption properties of single-walled carbon nanotubes such as SWNT,SWNT-COOH,and SWNT-OH and multi-walled carbon nanotubes including MWNT,MWNT-COOH,and MWNT-OH modified at a graphite electrode have been investigated by using [Fe(CN)₆]^3-anion and [Co(phen)₃]³⁺ cation.It was shown that shows good redox reversibility of [Fe(CN)₆]^3-/4-reactions on the existed carbon nanotubes(CNT) modified electrode.Based on the strong adsorptive property of [Co(phen)₃]³⁺ on the CNT surface,the [Co(phen)₃]³⁺/CNT modified graphite electrode can be obtained by progressive potential sweeping and developed to monitor quantitatively 6-mercaptopurine(6-MP).The adsorption capacity of …

High Utilization Aupt Nanoparticles Supported On Mwcnts For Methanol Electro-Oxidation In Alkaline Medium, Xun Guo, Dao-Jun Guo, Xin-Ping Qiu, Li-Quan Chen, Wen-Tao Zhu

Journal of Electrochemistry

We synthesized gold-platinum electrocatalysts supported on multi-walled carbon nanotubes(MWCNTs) with high utilization by a simple one-step method.A high Pt loading series of bimetallic AuPt/MWCNTs catalysts were prepared by the improved ethylene glycol reduction method,and then were compared in terms of the electrocatalytic activity for methanol electro-oxidation using cyclic voltammetry(CV) and chronoamperometry in alkaline solutions.The structure of AuPt/MWCNTs was characterized by the transmission electron microscopy(TEM),X-ray diffraction(XRD) and energy-dispersive X-ray spectroscopy(EDS).The results showed that the AuPt/MWCNTs catalysts had high Pt utilization,uniform AuPt nanoparticles size and good electrocatalytic activity for methanol electro-oxidation.The effect of Au/Pt mass ratio on electrocatalytic activity was also investigated.The …

Preparation And Electrochemical Performance Of Li3V2(Po4)3, Hou-Gang Fan, Tao Jiang, Chun-Zhong Wang, Gang Chen, Ying-Jin Wei

Journal of Electrochemistry

The carbon coating Li₃V₂(PO₄)₃ powder samples were synthesized by carbon incorporation solid state reaction.The structure,morphology and electrochemical properties have been studied by X-ray powder diffraction,scanning electron microscopy and automatic battery tester system,respectively.Carbon coating on Li₃V₂(PO₄)₃ would prevent the particles from agglomerating,reduce the particle size,raise the conductivity and improve the samples′ electrochemical performance.

Silicon Nanowires As Anode Materials For Lithium Ion Batteries, Yan-Peng Fu, Hui-Xin Chen, Yong Yang

Journal of Electrochemistry

The SiNWs electrodes were fabricated by coating and direct growth methods,respectively.The structure,morphology and electrochemical performance of such materials were characterized by XRD,SEM and charge-discharge tests.The results show that the electrodes prepared by direct growth method had higher capacity,better battery life and also displayed and excellent cyclability at higher currents.During the process of lithiation,the initial crystalline Si transformed to amorphous LixSi,and the average diameter of the SiNWs increased.Despite the large volume changed,the SiNWs remained intact and did not break into smaller particles.

Electrocatalytic Reduction Of Oxygen On Tungsten Carbide Electrode, Chun-An Ma, Yun Huang, Ying-Hong Zhu, Zhao-Yang Chen

Journal of Electrochemistry

Tungsten carbide(WC) catalysts were prepared by gas-solid reaction using ammonium metatungstate as precursors which were pretreated with spray drying sphere miniaturation,carbon monoxide as carrier gas and hydrogen as deoxidizing gas.The WC electrode was fabricated using WC catalyst powders and PTFE as binding agent,and characterized by XRD and SEM.Electrocatalyst behavior of WC for oxygen reduction reaction in the sulphuric acid solution was studied by steady-state voltammetry and cyclic voltammetry.The results show that the WC powders obtained were in spheric particles and the prepared WC electrode had a good electrocatalyst activity to the oxygen reduction reaction.The electrode reaction was controlled by adsorption.The …

Nano-Sn/Hard Carbon Composite As Anode Material For Lithium Ion Batteries, Bing-Kun Guo, Jie Shu, Kun Tang, Ying Bai, Zhao-Xiang Wang, Li-Quan Chen

Journal of Electrochemistry

The tin(Sn) nano particles were embedded into the mesopores of hard carbon spherules(HCS) to form a composite anode material for lithium ion batteries.The structure of the obtained composite was characterized by X-ray diffraction(XRD) while its electrochemical performances were evaluated with galvanostatic cycling.It is found that the embedding Sn nanoparticles into porous HCS not only result in a composite material with high lithium storage capacity and capacity retention,but also increase the initial coulombic efficiency of the composite.Based on the infrared spectroscopic analysis,the enhanced initial coulombic efficiency is attributed to the inductive decomposition of the ROCO₂Li species in the solid …

19th International Symposium Of Fine Chemistry And Functional Polymers (Fcfp-Xix) & Iupac 5th Internaitonal Symoposium On Novel Materials And Synthesis (Nms-V), Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

Preparation Of The Protic Ionic Liquid/Pvdf-Hfp Composite Membranes And Its Performance For Dmfc, Rui-Ying Miao, Jian-Ling Li, Yong Fang, Xin-Dong Wang

Journal of Electrochemistry

The protic ionic liquid(PIL) α-methyl pyridinium trifluoroacetate([α-MPyH]Tfa) was synthesized by acid & alkali neutralization.Then PIL/PVDF-HFP composite membranes were prepared by means of phase inversion method using acetone as solvent.The conductivities of the composite membrane increased with the temperature and reached 8×10^-3 S/cm,1×10^-2 S/cm and 3×10^-2 S/cm at room-temperature,30 ℃ and 80 ℃,respectively,by electrochemical impedance method.The properties of the methanol-rejecting of the membranes were measured by chronoamperometry as well.The results indicate that the properties of methanol-resistance of the membranes before and after IL combination were equivalent approximately.

Mesoporous Carbon For High Power Supercapacitors, Bin Xu, Lu Peng, Guo-Qing Wang, Gao-Ping Cao, Feng Wu, Yu-Sheng Yang

Journal of Electrochemistry

Mesoporous carbon for supercapacitors was prepared from sucrose using nano-CaCO₃ as template.The microstructure of the carbon was characterized with N₂ adsorption and transmission electron microscopy(TEM) observation.The electrochemical performances were evaluated in 6mol·L^-1 KOH aqueous electrolyte with galvanostatic charge/discharge,cyclic voltammetry,and ac impedance spectroscopy.The sucrose-based mesoporous carbon had a surface area of 606 m²/g and enriched mesopores in the range of 10～30 nm.The mesoporous carbon presented a specific capacitance of 125 F/g at a current density of 50 mA/g and outstanding excellent rate performance.As the current density increased to 20 000 mA/g,its capacitance remained at 88 F/g,much …

Preparation And Performance Of The Thin-Film Libpon Electrolyte, Feng Wu, Ya-Dong Liu, Ren-Jie Chen, Shi Chen

Journal of Electrochemistry

The LiBPON thin-film electrolyte was prepared by magnetron sputtering,and the relationship between the performance and the deposition condition was investigated.As seen in the SEM images,the thin films are dense and uniform without cracks,and according to the XRD patterns they have an amorphous structure.The electrochemical performance of the electrolyte was characterized by electrochemical impedance spectroscopy(EIS).The ionic conductivities of the thin film decreased with the RF power,but increased with the N₂ pressure.The an ionic conductivity of 3.5×10^-6 S/cm at room temperature was found from the electrochemical measurement.While the deposition rate increased with the RF power,but decreased with the N_{2 …}

Hydrothermal Preparation And Electrochemical Characterizations Of Vanadate Compound Nav2O5 Crystals, Fang Hu, Xing Ming, Fei Du, Ying-Jin Wei, Gang Chen, Chun-Zhong Wang

Journal of Electrochemistry

The NaV₂O₅ was prepared by a low temperature hydrothermal process. The material crystallized in the layered orthorhombic structure with space group Pmmn. X-ray diffraction confirmed that the material was pure and the scanning electron microscopy showed that the material was composed of needle crystals with 20 μm in length and 200 nm in width. X-ray photoelectron spectroscopy indicated the co-existence of V⁴⁺ and V⁵⁺ in the material,which results in an average V^4.5+ oxidation state of the material. The observed Raman bands were ascribed to different V-O vibrations. The first specific capacity about 120 mAh/g …

Photoelectrochemical Properties Of Tio2 Nanoparticles, Jie Qu, Ying Li, Qi-Wei Jiang, Xue-Ping Gao

Journal of Electrochemistry

The protonated titanate nanoparticles were obtained at room temperature and subsequently calcined at different temperatures(300 ℃,400 ℃,500 ℃,600 ℃ and 700 ℃) in air.The obtained products were characterized by XRD,TEM and UV-Vis.It is found that the grain sizes of TiO₂ nanoparticles calcined at 300 ℃ were about 20 nm,and increased gradually with the temperature rise.Photoelectric performance was measured with I～V curve and electrochemical impedance spectroscopy(EIS).The TiO₂ nanoparticles obtained at 500 ℃ showed the best photoelectrochemical properties with a photovoltaic conversion efficiency of 6.39%,which is much higher than those at other temperatures.In addition,it is also demonstrated that the charge …

Electrooxidation Behaviors Of Tib2 As High Capacity Anodic Material In Neutral Aqueous Electrolytes, Ya-Dong Wang, Xian-Yong Guang, Zhi-Xin Wang, Xin-Ping Ai, Han-Xi Yang

Journal of Electrochemistry

Titanium diborides were investigated as an anodic material for neutral aqueous batteries. It is revealed that this material shows superiorly high electrochemical activities in the neutral electrolytes. The discharge capacities observed for TiB₂ reached 1300 mAh/g at the constant current density of 50 mA/g, exceeding all the metal electrodes reported so far. The electrooxidation of this compound was found to proceed via the electrochemical dissolution of boron to form borofluoride, while titanium remained unchanged at the electrode. These results suggest a possible use of the boride compounds as a new material for constructing neutral aqueous batteries with high electrochemical …

The Electrochemical Performance Of Ncf-Sulfur Cathode, Chun-Rong Zhao, Zhong-Bao Yu, Wei-Kun Wang, Yu-Sheng Yang

Journal of Electrochemistry

The electrochemical performance of NCF-sulfur cathode, with different NCF contents, was investigated by constant current discharge, cyclic voltammetry and AC impedance methods. The morphologies of the cathodes were observed using scanning electron microscopy. The results indicate that the cycle life and rate capability of NCF-sulfur cathode increased. Better performance of sulfur cathode was obtained by 3% and 5% NCF conductive addition. When the current density was 0.4 mA/cm², the 3% NCF-sulfur cathode had an initial capacity of 880 mAh/g and a reversible capacity of 630 mAh/g after 20 cycles.

Preparation And Characterization Of Tin-Nickel Alloy Electromagnetic Shielding Fabric, Ke-Jing Chu, Wei Wang, Bin Sun, Mei-Fang Zhu

Journal of Electrochemistry

A soft electromagnetic shielding fabric was successfully prepared by electroplating tin-nickel alloy on the Cu-plated PET fabric in potassium pyrophosphate system. Results show that the different tin content and different colour can be obtained by changing the ratio of metals in bath. Better corrosion resistance and anti-tarnishing were achieved with the fabric consisting of 68.96% Sn. The tin-nickel alloy surface for the electromagnetic shielding fabric had excellent conductivity, softness, permeability and soft luster, non-sensitized to the human body. Thereby it has broad prospect in EMI field and shielding clothing.

Electrosynthesis Of 2,2-Dimethylolpropionic Acid, Hong-Yan Sun, Zhen-Hai Liang

Journal of Electrochemistry

The Ti/SnO₂+Sb₂O₄/PbO₂ electrode was prepared.The structure phase and valent state were characterized by means of XRD and XPS.The 2,2-dimethylolpropionic acid was synthesized on the Ti/SnO₂+Sb₂O₄/PbO₂ anode by direct electro-oxidation of 2,2-dimethylolpropionaldehyde.The product and crude material were analyzed by HPLC,the effects of the concentration of 2,2-dimethylolpropionaldehyde,pH,potential and reaction temperature were studied.The results showed that the optimum conditions were anode potential 1.8 V,pH=1,reaction temperature 15 ℃ and 2,2-dimethylolpropionaldehyde concentration 0.10mol/L.Under the optimum conditions,the selectivity of 36%,the current efficiency of 28% and the conversion of 58% were reached.The reported …

The Electrochemical Behavior And Determination Of Carbendazim On Iron Montmorillonite Modified Electrode, Xiao-Li Jiang, Rong Li, Xiao-Ying He, Jiang Li, Ying Li

Journal of Electrochemistry

The FeCl₃ modified clay electrode was made.The electrochemical behavior of carbendazim(BCM) on the modified electrode was studied by cyclic voltammetry.The impacts of pH,scan rate and dosages of modifier were discussed and the important kinetic parameters of the electrochemical process were determined.The results indicated that the process was controlled by diffusion.The effective area of FeMM-CMC/GCE(A)=0.027 cm²,the transfer electron numbers(n)=2 and the diffusion coefficient(D)=5.115×10^-6cm²/s.Under the optimized conditions,a good linearity was found between the first order derivative of peak current and concentration of BCM in the range of 2.00×10^-5～8.00×10^-4mol/L,with i′p=-8.045×10^-7-0.0237c,correlation …

Synthesis,Characteristics And Electrochemical Performance Of Nano-Sized Snco/Graphite Composites As Anode For Lithium Ion Batteries, Jin-Shu Cai, Ling Huang, Fu-Sheng Ke, Shi-Gang Sun

Journal of Electrochemistry

The nano-structural Sn-Co/graphite composites were prepared by chemical reduction of the alloy electroless deposition solution in graphite suspensions, and the composites were annealed at 500 ℃. The phase structure and surface morphology of the composites were measured by XRD, SEM and Raman. The results indicate that there were high dispersions and high loadings of Sn-Co nanoparticles on graphite by thermal treatment. Electrochemical lithium storage performance was studied preliminarily on the obtained samples. The graphite modified with the Sn-Co nanoparticles possessed a higher electrochemical reversible capacity than that of graphite during the charge and discharge process. The appetency between the Sn-Co …

Yttrium And Hydrogen Superstructure And Correlation Of Lattice Expansion And Proton Conductivity In The Bazr0.9y0.1o2.95 Proton Conductor, A. Braun, A. Ovalle, V. Pomjakushin, A. Cervellino, S. Erat, Wayne C. Stolte, T. Graule

Chemistry and Biochemistry Faculty Research

Bragg reflections in Y-resonant x-ray diffractograms of BaZr_0.9Y_0.1O_2.95 (BZY10) reveal that Y is organized in a superstructure. Comparison with neutron diffraction superstructure reflections in protonated/deuterated BZY10 suggests that both superstructures are linked, and that protons move in the landscape imposed by the Y. The thermal lattice expansion decreases abruptly for protonated BZY10 at T≥648±20 K, coinciding with the onset of lateral proton diffusion and suggesting a correlation of structural changes and proton conductivity. The chemical shift in the Y L₁-shell x-ray absorption spectra reveals a reduction from Y³⁺ toward Y²⁺ upon …

Study Of Corrosion Of Materials In The Sulfur-Iodine Hydrogen Production Cycle, Thao Trung Ho

UNLV Theses, Dissertations, Professional Papers, and Capstones

Hydrogen is of great interest since the availability of traditional fossil fuels is in decline. Strictly speaking, hydrogen is not a primary source of energy but is an energy carrier, since energy typically must be used from another source (electricity, natural gas, coal, etc.) to produce it. Of hydrogen production techniques, the Sulfur-Iodine thermochemical water splitting process (S-I cycle), which was proposed by General Atomics (GA), is promising with its simplicity and high efficiency. Most of the chemicals are recycled except water. However, the S-I cycle operates in a harsh, corrosive environment in the presence of a mixture of iodine …

Spectroscopic Investigation Of Palladium-Copper Bimetallic Systems For Pem Fuel Cell Catalysts, Timo Hofmann

UNLV Theses, Dissertations, Professional Papers, and Capstones

One of the main barriers to commercialization of polymer electrolyte membrane fuel cells systems is cost, which is largely due to the need of platinum (Pt)-containing catalysts. In this thesis we investigate bimetallic systems consisting of a base metal (copper) and a noble metal (palladium) that, as an alloy on the nanoscale, mimic the electronic properties that make Pt desirable as a catalyst.

We present a detailed investigation of the electronic structure of carbon-supported Pd/Cu nanoparticle catalysts, model bilayer thin film systems, alloys, and various metal reference samples. We have investigated the valence band structure of the catalysts using a …

Studies Of Surface Diffusion In Pemfc Electrodes, Jiang-Shui Luo, Jian Chen, Bao-Lian Yi, Chuan-Sin Cha, Hua-Min Zhang

Journal of Electrochemistry

A PEMFC electrode consisting of dual-layer catalyst layer(CL) was fabricated in this work. The outer CL was Nafion-free,while the inner CL was Nafion-bonded. The effects of Pt/C catalyst in the outer CL that did not contact with Nafion on the current generation in PEMFC electrodes were investigated. Cyclic voltammetric studies indicated that the Pt/C catalyst in the outer CL without direct contact with Nafion was still electrochemically active in taking part in the adsorption/desorption of hydrogen and the electrochemical oxidation/reduction of the oxygen-containing species occurring at the interface of "Pt/Nafion" in the inner CL. The polarization curves showed that the …

Ec-Pt/Cnts Glucose Oxidative Electrode, Jia-Hua Liang, Chun-Mei Zhou, Hong-Juan Wang

Journal of Electrochemistry

A glucose oxidative electrode(GOD),EC-Pt/CNTs glucose oxidative electrode,was constructed by ethyl cellulose(EC) and Pt/CNTs.The sensitivity of the EC-Pt/CNTs GOD is 0.85 μA/mM in the concentration range of 0～4 mmol/L of glucose.After dipped in PBS(4℃) for 18 days,the activity of the EC-Pt/CNTs GOD can reach 80%.It is promising for the EC-Pt/CNTs GOD to be used to construct glucose biosensor.

Corrosion Inhibition Of Magnesium Alloy In 3.5% Nacl Medium By Tungstate, Ling-Jie Li, Zhi-Ming Yao, Jing-Lei Lei, Dong-Hai He, Sheng-Tao Zhang, Fu-Sheng Pan

Journal of Electrochemistry

Electrochemical impedance spectroscopy(EIS),Tafel polarization curves and scanning electron microscopy(SEM) were used to study the corrosion inhibition of AZ61 magnesium alloy in 3.5% NaCl medium with tungstate.Results showed that tungstate demonstrates strong inhibition to the corrosion of AZ61 magnesium alloy.At the concentration of 0.01 mol/L,tungstate has a high inhibition efficiency 75.5%.Tungstate is an anodic inhibitor that mainly inhibited the anodic reactions of magnesium alloy through forming a compact protective layer that covered the magnesium alloy surface active sites.

Behavior Of Copper Electrodeposition In Copper Electroplating Solution With Different Peg Molecular Weight, Lie Yin, Zeng-Lin Wang

Journal of Electrochemistry

The effect of the polyethylene glycol(PEG) molecular weight(MW) upon via-hole filling with diameter of 50 μm and aspect ratio of 1 in the acid copper plating solution was studied.The cathodic polarization in copper electroplating bath with PEG of different molecule weights was investigated by linear sweep voltammetry.The surface roughness,crystallography,and the resistivity of copper films were characterized by X-ray diffraction(XRD),atomic force microscopy(AFM) and the four-point probe measurements.The results showed that the polarization on the cathode and the hole-filling capability of electroplating copper bath were increased evidently with an increase of PEG molecular weight from 600 to 8000.When the PEG MW was …