Physical Chemistry Commons^™

Synthesis And Electrochemical Properties Of Yttrium-Doped Lini0.49Mn1.49Y0.02O4, Xian-Wen Zhang, Zheng-Xi Zhang, Li Yang, Shao-Hua Fang, Long Qu

Journal of Electrochemistry

The LiNi_0.49Mn_1.49Y_0.02O₄ cathode material was synthesized using the citric acid-assisted sol-gel method by partial substitutions of Ni and Mn with Y in the LiNi_0.5Mn_1.5O₄ material. The influences of Y doping on the structure and electrochemical properties were investigated by means of X-ray diffraction, cyclic voltammetry, galvanostatic charge/discharge tests and AC impedance spectroscopy. The results showed that the introduction of Y into the LiNi_0.5Mn_1.5O₄ greatly improved the cycle performance and rate capability. When the charge and discharge current was 1 C in the potential …

Template-Free Synthesis Of Porous Nio Hierarchical Structure For High Performance Supercapacitors, Yun Huang, Zhong Wu, Xin-Bo Zhang

Journal of Electrochemistry

A facile and template-free hydrothermal method is proposed to successfully synthesize porous NiO hierarchical structure, which is found to be assembled from ultrathin NiO nanosheets. As for electrochemical pseudocapacitor application, the obtained material exhibits not only high specific capacitances of 435 F·g^-1 at 20 mV·s^-1 and 367 F·g^-1 at 10 A·g^-1, but also holds a good electrochemical stability over 1000 cycles at a current rate of 20 mV·s^-1. These results suggest that the hierarchical structured porous NiO is a promising supercapacitor electrode material.

Electrochemical Reduction Of Co2 On Sn/Cu Electrodes, Chen-Chen Zhao, Jian-Wei Guo, Li Wang, Xiang-Ming He, Cheng Wang, Zhi-Xiang Liu

Journal of Electrochemistry

The Sn/Cu electrodes were prepared by electroplating method and their morphologies under different galvanization current densities were determined by SEM. In alkali, the effects of Sn/Cu electrodes on the activities towards hydrogen evolution and electrochemical reduction of CO₂ were investigated in alkaline solutions using a three-electrode system. These results indicated that the Sn/Cu electrodes prepared at 10 mA/cm² and 15 mA/cm² showed good activities, while that prepared at 15 mA/cm² was even better in activities. The synergetic structure of the Sn/Cu electrode to be beneficial to electrochemical reduction of CO₂ has been pointed out.

Electrochemical Properties Of The Keggin-Type Lacunary Heteropolysilicate Anion And Its Eectrocatalysis For H2O2 Reduction, Xi-Long Liu, Chun-Yan Wu, Fang Zhou, Hong-Sheng Liu, Ying-Jie Hua, Chong-Tai Wang, Xiao-Yang Liu

Journal of Electrochemistry

Electrochemical properties of the Keggin-type lacunary heteropolysilicate anion SiW₁₁O₃₉^8- (SiW₁₁) and its indirect electrocatalysis for H₂O₂ reduction in the supporting electrolyte containing 0.1 mol·L^-1 NaHSO₄ and Na₂SO₄ solutions were investigated using cyclic voltammetry, square wave voltammetry and alternating current impedance spectroscopy. Experimental results indicated that SiW₁₁ showed two pairs of reversible redox waves on the glassy carbon (GC) electrode in an acidic solution. The electron transfer number corresponding to the two pairs of waves was one, and the proton transfer number involved was two during …

Corrosion Inhibition Of 316l Steel Using Sodium Diethyl Dithiocarbamate Solution In Simulated Crude Oil, Xiao-Guang Ren, Jie Yang

Journal of Electrochemistry

The corrosion inhibition behaviors of 316L steel using the sodium diethyl dithiocarbamate (SDDTC) compound in the crude simulation solution were studied in the absence and presence of zinc sulfate or sodium chromate with different compositions. Experiment resultss showed that in the environments of highly acidic and high concentrations of chloride ions the SDDTC compound could well inhibit the corrosion of 316L steel. The good synergic effects on the corrosion inhibition of 316L steel by additions of either zinc sulfate or sodium chromate into SDDTC compound were indicated in this study, which is of great significance and importance in practical applications.

Synthesis And Theoretical Studies Of Pyridyl Fullerene Derivatives For Supramolecular Applications In Photovoltaic Systems, Robert Vina-Marrufo ^, Danisha M. Rivera-Nazario, Agustin Molina-Ontoria, Luis Echegoyen *

COURI Symposium Abstracts, Spring 2012

No abstract provided.

Towards One Key To One Lock: Catalyst Modified Indium Oxide Nanoparticle Thin Film Sensor Array For Selective Gas Detection, Kun Yao, Daniela Caruntu, Sarah Wozny, Rong Huang, Yumi H. Ikuhara, Baobao Cao, Charles J. O'Connor, Weilie Zhou

Advanced Materials Research Institute (AMRI)

Homogeneous In2O3 nanoparticles (NPs) were self-assembled into thin film sensor arrays on a single chip, with further surface modification by noble metal catalysts. The NP film sensor arrays show clear current responses when exposed to different target gases, and both sensitivity and selectivity were greatly improved. Particularly, the sensors modified with Au, Pd, and Pt nanocatalysts demonstrated higher sensitivity to H2S, H-2 and CO, respectively, making the gas discrimination direct and simple, like "one key to one lock". The particle size dependence of the noble metal modifiers to the sensitivity was further investigated by tuning the sputtering parameters. Three different …

The Electrocatalytic Study Of Licoo2 In Air Electrode For Lithium-Air, Jun Gao, Wei Wu, Yan-Yan Tian, Yong Yang

Journal of Electrochemistry

The LiCoO₂ has been investigated as a new electrocatalyst for air electrodes using homemade lithium-air battery. The electrochemical performance and structural changes of the LiCoO₂ based composite air electrodes have been studied. The results of CV, XRD and charge-discharge tests show that the composite air electrodes composed of LiCoO₂ can greatly improve the discharge performance of lithium-air batteries. In particular when the composite air electrodes are charged to 4.1 V before further discharging, the obvious catalytic effects of LiCoO₂ are attributed to higher valence state of the Co element in LiCoO₂, esp. at charged …

Electrochemical Characterization Of (Phmgcl)2-Alcl3/Mixed Ether Electrolytes, Fei-Fei Wang, Yong-Sheng Guo, Jun Yang, Li-Yan-Na Nu, Jiu-Lin Wang

Journal of Electrochemistry

The (PhMgCl)₂-AlCl₃ salts were prepared and the electrochemical properties of (PhMgCl)₂-AlCl₃ electrolytes containing dimethoxyethane(DME)+THF, Diglyme(DG)+THF and Tetraglyme(TG)+THF solvents with different proportions on various metal electrodes were studied. Compared with (PhMgCl)₂-AlCl₃/THF, the (PhMgCl)₂-AlCl₃/DG+THF(3:2) solvents showed high ionic conductivity of 1.605×10^-3 S·cm^-1, good reversible Mg deposition behavior and anodic anti-oxidation performance with an electrochemical window wider than 2.8 V. In addition, the DG+THF mixed solvent could greatly lower the saturated vapor pressure by reducing from 23.46 kPa to 9.41 kPa, which suppresses volatilization of the …

Electrocatalytic Study Of Pseudomonas Aeruginosa Bte-1 Strain, Ping Zhou, En-Ren Zhang, Li Zhou, Guo-Wang Diao, Jun-Le Niu

Journal of Electrochemistry

The aim of the present study is to investigate the electrocatalytic activity of electricity-producing Pseudomonas aeruginosa BTE-1 strain under anaerobic conditions. Pseudomonas aeruginosa BTE-1 was inoculated into anaerobic three-electrode electrochemical cells, and the electrocatalytic activity was measured at poised potentials. HPLC and cyclic voltammetry were used to detect potential electron mediators in solutions. Experimental results showed that no detectable pyocyanine was excreted by P. aeruginosa BTE-1 strain in the anaerobic electrochemcial cells, and P. aeruginosa BTE-1 exhibited direct electrocatalytic activity through the formation of biofilm on the electrode surface which was induced by the electron transfer from the cells of …

Cycle Lifetime Investigation Of Nickel Electrode Prepared By Electrochemical Impregnation For Applications In Aerospace Nickel Hydrogen Cells, Hai-Chang Zhang, Li-Xin Tan, Cheng Guo, Wen-Cheng Ming, Xue-Ying Ren

Journal of Electrochemistry

In this paper, the effects of overcharge, charge-discharge C rate and pore size on cycle lifetime of 4.5’ electrochemical impregnated nickel electrode were investigated. In the case of the electrode was overcharged to 170% of nominal capacity, the initial capacity of the electrode could be maintained 2.7 Ah up to 150 cycles without deterioration and a discharge capacity of 1.7 Ah (remaining 63% of 2.7 Ah) could be delivered after 300 cycles. Without overcharge, more than 300 charge-discharge cycles could be realized without loss of capacity and a discharge capacity of electrode could be maintained about 76% of initial capacity …

Dissolved Oxygen Seawater Battery With Electrochemical Capacitance, Hai-Bo Xu, Yong-Hong Lu, Wei Zhang, Yan-Ting Yu, Chuan-Wei Yan, Ya-Ping Sun, Lian Zhong, Jian-Guo Liu, Yi Zheng, Bing Han, Yong-Liang Wang

Journal of Electrochemistry

A new concept of seawater battery with electrochemical capacitance (SWB-EC) has been proposed using carbon fibre brush (CFB) as the cathode material, and three testing prototypes have been made accordingly. The discharge performances of the CFB before- and after-oxidation and Mg alloy sacrifice anode were studied by cyclic voltammetry and constant current discharge tests under steady state conditions. Results show that the oxidized CFB exhibits the pseudo-capacitive characteristic and its activity of oxygen reduction reaction (ORR) in stirred seawater highly increases, comparing with the non-oxidized CFB. The open circuit potential of Mg alloy sacrifice anode is -1.74 V, having the …

Simultaneous Determinations Of Ascorbic Acid, Dopamine And Uric Acid At Ca/Gc Electrode, Ying Zhang, Wang Ren, Min-Jiao Li

Journal of Electrochemistry

The citric acid modified glassy carbon electrode (CA/GC) was constructed by potentiostatic technique and used for simultaneous determinations of ascorbic acid (AA), dopamine (DA) and uric acid (UA) by cyclic voltammetry (CV) and differential pulse voltammetry (DPV). The CA/GC electrode exhibits excellent electrocatalytic activity towards AA, DA and UA. The oxidation peaks are well separated with the potential differences between AA and DA, DA and UA, and AA and UA being 170, 130 and 300 mV, respectively, which is large enough to determine AA, DA and UA simultaneously. The catalytic peak currents obtained were linearly dependent on the concentrations of …

Progress And Perspective Of Fuel Cell Technology, Ming Hou, Bao-Lian Yi

Journal of Electrochemistry

Fuel cell, a clean and high-efficiency electrochemical power source, has being paid much attention worldwide recent years. In this paper, the progress and perspective of fuel cell technology are elucidated in detail. Fuel cells have been applied in some special fields such as spacecraft, shuttle and submarines. However, in the areas of transportation, stationary station and portable power source, fuel cells are still under demonstration due to the durability and cost problems. The reliability and surrounding survivability of fuel cells should be enhanced in the special application. Meanwhile, the durability and cost of fuel cells are the main issues to …

Preparation And Electrochemical Performance Of Lifepo4/C By Spray Drying Method Assisted With Organic Template, Quan-Bing Liu, Yang-Mei Jiang, Hui-Yu Song, Shi-Jun Liao

Journal of Electrochemistry

In this work, the LiFePO₄/C composites were prepared by the spray drying and carbothermal method, and were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and galvanostatic charge-discharge measurements. The effects of the organic assisted templates on the morphologies and electrochemical properties of the LiFePO₄/C composites were investigated. The results showed that the morphology and microstructure of the composites could be tuned by incorporating with the different templates. The morphology of the composite appeared to be solid microspheres if no organic template was added, while porous microspheres, nest-like …

Synthesis And Electrochemical Performance Of Xlifepo4·Yli3V2(Po4)3 Composites, Ping-Ping Ma, Zhi-Jian Liu, Jian-Hua Xia, Yu Chen, Pu Hu, Zhi-Chao Lu, Ding-Guo Xia

Journal of Electrochemistry

A series of xLiFePO₄·yLi₃V₂(PO₄)₃ composites were systematically synthesized through solid state reactions by variations in the proportions of LiFePO₄ and Li₃V₂(PO₄)₃. The properties of the prepared compounds were investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical measurements. The capacity of 162.7 mAh/g at 0.2 C rate was obtained with the relatively good cycle stability and good conductivity for 0.95LiFePO₄·0.05Li₃V₂(PO₄)₃ due to more uniformed distributed and smaller particle sizes.

Preparation And Characterization Of Mno/Tin Anode For Lithium Ion Batteries, Gao-Jie Xu, Hai-Yan Yang, Peng-Xian Han, Li-Xue Zhang, Ke-Jun Zhang, Chuan-Jian Zhang, Yu-Hua Fan, Cai-Feng Bi, Guang-Lei Cui

Journal of Electrochemistry

Manganese titanate (MnTiO₃) powder was prepared via a sol-gel method using manganese acetate and tetrabutyl titanate as raw materials, and citric acid as a chelating agent. Through high temperature nitridation of MnTiO₃ powder in ammonia, the MnO/TiN composite was obtained. The phase structure, composition and morphology of the composites were characterized by XRD, SEM and EDS. The electrochemical properties of the composite electrodes were studied by performing cyclic voltammetry, galvanostatic charge and discharge, and electrochemical impedance spectroscopy tests. The MnO/TiN electrode delivered specific capacities of 394 mAh·g^-1 and 146 mAh·g^-1 at the current density of …

Preparation And Hydrogen Evolution Properties Of Ni/Ag2O/Ruo2-Pt Cathodes, Shu Huang, Xue-Ming Li, Wu-Lin Li, Wen Wang

Journal of Electrochemistry

The Ni/Ag₂O/RuO₂-Pt composite cathode was prepared by sol-gel method using RuCl₃ and H₂PtCl₆ as raw materials. The effects of heat treatment conditions and AgNO₃ concentrations on hydrogen evolution properties were investigated. The morphology and composition of Ni/Ag₂O/RuO₂-Pt composite cathode have been characterized by XRD, XPS and SEM-EDS. It is demonstrated that the surface structure of Ni/Ag₂O/RuO₂-Pt composite cathode is more compact, with fewer cracks and larger surface roughness than pure nickel. At the conditions of 0.3 A·cm^-2, 90 ^oC, and …

Ag Nanoparticles Self-Assembled Films On Iron Surface And Their Inhibition Properties, Zhe Zhang, Ming-Zi Jia, Le Ruan

Journal of Electrochemistry

The Ag nanoparticles were prepared in aqueous solutions through a chemical reduction method and transferred from water phase to toluene phase with the protection of 1-dodecanethiol (DDT). The polished iron electrode was immersed in the DDT-protected metal nanoparticles toluene solutions to form DDT/Ag nanoparticles self-assembled mixed films. Electrochemical methods such as electrochemical impedance spectroscopy and polarization curve measurement were used to study the inhibition properties of the self-assembled films in the 0.5 mol·L^-1 H₂SO₄ solution. The appearance of elements such as S and Ag from the XPS data identified the presences of DDT and Ag nanoparticles.

Horizontally-Aligned Carbon Nanotubes Arrays And Their Interactions With Liquid Crystal Molecules: Physical Characteristics And Display Applications, Frederick Roussel, Jean-Francois Brun, Alexandre Allart, Limin Huang, Stephen O'Brien

Publications and Research

We report on the physical characteristics of horizonthally-grown Single-Walled Carbon Nanotubes (h-al-SWNT) arrays and their potential use as transparent and conducting alignment layer for liquid crystals display devices. Microscopy (SEM and AFM), spectroscopic (Raman) and electrical investigations demonstrate the strong anisotropy of h-al-SWNT arrays. Optical measurements show that h-al-SWNTs are efficient alignment layers for Liquid Crystal (LC) molecules allowing the fabrication of optical wave plates. Interactions between h-al-SWNT arrays and LC molecules are also investigated evidencing the weak azimuthal anchoring energy at the interface, which, in turn, leads to LC devices with a high pretilt angle. The electro-optical reponses of …

Ƴ-Selective Directed Catalytic Asymmetric Hydroboration Of 1,1-Disubstituted Alkenes, Sean M Smith, Gia L. Hoang, Rhitankar Pal, Mohammad O. Bani Khaled, Liberty S. W. Pelter, Xiao Cheng Zeng, James M. Takacs

Xiao Cheng Zeng Publications

Directed catalytic asymmetric hydroborations of 1,1-disubstituted alkenes afford ƴ

-dioxaborato amides and esters in high enantiomeric purity (90–95% ee).

Synthesis And Flame Retardant Testing Of New Boronated And Phosphonated Aromatic Compounds, Vladimir Benin, Sravanthi Durganala, Alexander Morgan

Chemistry Faculty Publications

The present report describes the preparation and use of some dimethyl terephthalate derivatives in transition metal-catalyzed coupling reactions to produce new reactive flame retardants. Dimethyl iodoterephthalate and dimethyl 2,5-diiodoterephthalate were successfully employed in the preparation of phosphonic and boronic esters and acids. The latter were tested for heat release with a microcombustion calorimeter (ASTM D7309) to determine the potential for heat release reduction of these flame retardant molecules. The results showed that the addition of boronic or phosphonic acids greatly lowered the heat release, due to a condensed phase (char formation) mechanism. Adding ester groups to the boronic acids or …

Development Of Tailor-Designed Gold-Platinum Nanoparticles Binary Catalysts For Efficient Formic Acid Electrooxidation, Islam M. Al-Akraa Dr, Ahmad M. Mohammad Prof, Mohamed S. El-Deab Prof, Bahgat E. El-Anadouli Prof

Chemical Engineering

The modification of a glassy carbon (GC) electrode with platinum (PtNPs) and gold (AuNPs) nanoparticles is targeted to fabricate efficient anodes for the electrooxidation of formic acid (FA). A proper adjustment of the deposition sequence of PtNPs and AuNPs could eventually enhance the electrocatalytic activity of the electrode in such a way that suppresses the CO poisoning effect during FA oxidation. The highest catalytic activity is obtained at the Au/Pt/GC electrode (with PtNPs firstly deposited on the GC electrode followed by AuNPs). This superb enhancement is quantified by comparing the relative ratio of the direct vs. the indirect oxidation peaks …

Self-Assembling Subnanometer Pores With Unusual Mass-Transport Properties, Xibin Zhou, Guande Liu, Kazuhiro Yamato, Yi Shen, Ruixian Cheng, Xiaoxi Wei, Wanli Bai, Yi Gao, Hui Li, Yi Liu, Futao Liu, Daniel M. Czajkowsky, Jingfang Wang, Michael J. Dabney, Zhonghou Cai, Jun Hu, Frank V. Bright, Lan He, Xiao Cheng Zeng, Zhifeng Shao, Bing Gong

Xiao Cheng Zeng Publications

A long-standing aim in molecular self-assembly is the development of synthetic nanopores capable of mimicking the mass-transport characteristics of biological channels and pores. Here we report a strategy for enforcing the nanotubular assembly of rigid macrocycles in both the solid state and solution based on the interplay of multiple hydrogen-bonding and aromatic π − π stacking interactions. The resultant nanotubes have modifiable surfaces and inner pores of a uniform diameter defined by the constituent macrocycles. The self-assembling hydrophobic nanopores can mediate not only highly selective transmembrane ion transport, unprecedented for a synthetic nanopore, but also highly efficient transmembrane water permeability. …

Synthesis And Investigation Of The Liquid Crystalline Properties Of Polycyclic Aromatic Hydrocarbons, Joseph A. Paquette

Theses and Dissertations (Comprehensive)

In this thesis, the synthesis and liquid crystalline properties of a series of novel substituted dibenz[a,c]anthracenes is reported. Specifically, a series of hexaalkoxydibenz[a,c]anthracenes were prepared and found not to exhibit a mesophase. In contrast, when substituents are introduced on the aromatic core, columnar mesophases are observed over broad temperature ranges. A series substituted derivatives was prepared and their mesomorphic properties compared. In general, electron-withdrawing substituents promote broad mesophase temperature ranges, as do larger substituents. The liquid crystalline phase is a result of the electronic effects, size and shape of the substituents in the 10 and 13 positions.

We also synthesized …

The Tetrafluoroborate Salt Of 4-Methoxybenzyl N-2-(Dimethylamino)Ethyl-N-Nitrosocarbamate: Synthesis, Crystal Structure And Dft Calculations, Helene Hedian, Vladimir Benin

Chemistry Faculty Publications

The tetrafluoroborate salt of 4-methoxybenzyl N-2-(dimethylamino)ethyl-N-nitrosocarbamate was prepared in two steps, via the corresponding carbamate. Its crystal structure is monoclinic, space group P21/c. The unit cell dimensions are: a = 19.499(8) Å, b = 5.877(3) Å, c = 15.757(7) Å, α = 90°, β = 110.019(7)°, γ = 90°, V = 1696.5(12) Å3, Z = 4. The structure exhibits an unexpected, pseudo-gauche conformation with respect to the C2–C3 bond, due to a stabilizing hydrogen bond between the carbonyl oxygen (O1) and the hydrogen atom at the trialkylammonium center (H3n), with a distance between them of …

Preparation And Application Of Nano-Nio As Anode In Lithium-Ion Batteries, Cheng-Dong Bai, Jia-Jia Chen, Qi Zhang, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

In this work, the nano-NiO material was prepared by hydrothermal method. The surface morphologies and electrochemical properties of nano-NiO material were investigated. The special nano-NiO material with porous surface assembling honeycombs(100-200nm) was obtained by using surface active agents. The discharge capacity of nano-NiO electrode up to 2385.7 mAh/g was achieved at current density of 0.1A/g in the first circle,while 1100mAh/g could be maintained after 100 circles. At current density of 2.0A/g, the discharge capacity of 600 mAh/g was obtained. And when the current density was reduced to 0.1A/g, the discharge capacity was restored to 1050 mAh/g. The nano-NiO electrode exhibited …

Corrosion Behaviors Of 316 Stainless Steel Weldment Studied By Array Reference Electrodes, Wang-Huo Yang, Rong-Gang Hu, Chen-Qing Ye, Wei Hang, Ning Li, Chang-Jian Lin

Journal of Electrochemistry

The array reference electrodes were developed to in situ measure the potential distributions of the welded 316 stainless steel in 12% FeCl3 solution, combined with metallographic analysis, polarization curve, EIS measurement and Kelvin volta potential imaging. It was indicated that the weld zone of metal suffered a serious preferential corrosion when immersed in the environment due to the distinct changes of structure and composition during the welding process. With time prolonging, the corrosion potential of the welding zone was negatively shifted to a maximum value, and then declined gradually. At 45 min immersion, the corrosion development from welding zone to …

Microemulsion Preparation And Electrochemical Characterization Of Pt/C, Ptir/C Electrocatalysts, Ya-Ping Zeng, Sheng Sui

Journal of Electrochemistry

The Pt/C electrocatalysts were prepared by three different systems and the PtIr/C electrocatalysts were prepared with four different Ir contents. The samples were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM), cyclic voltammetry (CV), potentiostatic and potentiodynamic polarizations measurements. The experimental results confirmed that the electrocatalyst particles prepared by the microemulsion method were well distributed on XC-72R supports with the active particle sizes of 5～10nm and good electrocatalysts activity. The Pt85Ir15/C electrocatalysts showed the highest overall electrochemical activity in unitized regenerative fuel cell.

Preparation And Characterization Of Casno3 Anode Material For Lithium Ion Batteries, Ran Sun, Zi-Geng Liu, Ya-Qi Jiang

Journal of Electrochemistry

In this study the precursor CaSn(OH)₆ was prepared via a hydrothermal process, and its composition, surface feature and phase-transition were characterized by XRD, SEM and DSC-TGA. The shapes of CaSn(OH)₆ crystals were effectively controlled by adjusting the volumn ratio of H₂O and CH₃CH₂OH solvents. Perovskite CaSnO₃ could be obtained by calcination of CaSn(OH)₆ at 800 ℃. The reversible capacity of 334.4 mAh/g with good cycling stability could be achieved with the CaSnO₃ electrode.