Open Access. Powered by Scholars. Published by Universities.®

Chemistry Commons™

Open Access. Powered by Scholars. Published by Universities.®

Materials Science and Engineering

Institution
Keyword
Publication Year
Publication
Publication Type
File Type

Articles 1801 - 1830 of 2635

Full-Text Articles in Chemistry

Electrodeposition Of Nano-Sb-Zn Alloy In Acetamide-Urea-Nabr-Kbr Melt, Peng Liu, Xin-Ai Guo, Ye-Xiang Tong, Qi-Qin Yang Aug 2006

Electrodeposition Of Nano-Sb-Zn Alloy In Acetamide-Urea-Nabr-Kbr Melt, Peng Liu, Xin-Ai Guo, Ye-Xiang Tong, Qi-Qin Yang

Journal of Electrochemistry

The electroreduction of Zn(II) and Sb(III) in acetamide-urea-NaBr-KBr(343 K) were studied by cyclic volatmmetry.The reduction of Zn(II) or Sb(III) to the metals is an irreversible process.The transfer coefficient of Zn(II)+2e→Zn and Sb(III) +3e→Sb were calculated to be 0.231 and 0.319,the diffusion coefficient of Zn(II) and Sb(III) in the melt were determined as 1.70*10-6 and 3.21*10-6 cm2· s-1 respectively.The Zn-Sb films with different Zn content from 29.67 at% to 97.34 at% were electrodeposited in acetamide-urea-NaBr-KBr melt at 343 K by controlling the deposition potential and the Zn(II)/Sb(III) molar ratio.The morphology of Zn-Sb film was observed by …

Go to article

Investigations On Electrochemical Characteristics Of Liv3O8 Electrode In Lithium Sulfate-Water-Ethanol Electrolytes, An-Bao Yuan, Wei-Xiang Song Aug 2006

Investigations On Electrochemical Characteristics Of Liv3O8 Electrode In Lithium Sulfate-Water-Ethanol Electrolytes, An-Bao Yuan, Wei-Xiang Song

Journal of Electrochemistry

The active material of LiV3O8 prepared using low-temperature pre-reaction in solution followed by intermediate-temperature calcination at 450 ℃.The product was characterized by X-ray diffraction analysis and scanning electron microscope observation.The performance of LiV3O8  electrode in neutral lithium sulfate-water-ethanol electrolytes was investigated using electrochemical methods.Galvanostatic charge/discharge results indicated that the specific capacity of LiV3O8  electrode decreases with ethanol content increasing in electrolyte.The most appropriate water/ethanol volumetric ratio is 4 ∶1 in terms of conductivity of the electrolyte and stability of the electrode.AC impedance measurements demonstrated that the ohmic resistance of the electrolyte …

Go to article

The Influence Of Pva As Disperser On Lifepo4 Synthesized By Hydrothermal Reaction, Hui-Lin Li, Hui Zhan, Yu-Hong Zhou Aug 2006

The Influence Of Pva As Disperser On Lifepo4 Synthesized By Hydrothermal Reaction, Hui-Lin Li, Hui Zhan, Yu-Hong Zhou

Journal of Electrochemistry

LiFePO4 was synthesized by means of hydrothermal reaction,in which PVA acts as disperser and glucose as carbon source. The samples were characterized by X-ray diffraction, scanning electron microscopy and electrochemical measurement. SEM results show that the sample is homogeneously composed of grains with a particle size of ca.200nm. In the charge/discharge test, the products exhibited a 3.45V discharge voltage plateau and a maximum specific capacity of 140mAh/g. After 40 cycles, its capacity only declined by 2.1%. Besides these, the mechanism for the influence of the particle size and carbon coating on the electrochemical property of LiFePO4 material was …

Go to article

Calcined Temperatures Influence On Synthesis And Electrochemistry Charactarization Of Li[Ni0.475Mn0.475Co0.05]O2 For Li-Ion Batteries, Li-Qin Wang, Li-Fang Jiao, Hua-Tang Yuan, Yong-Mei Wang Aug 2006

Calcined Temperatures Influence On Synthesis And Electrochemistry Charactarization Of Li[Ni0.475Mn0.475Co0.05]O2 For Li-Ion Batteries, Li-Qin Wang, Li-Fang Jiao, Hua-Tang Yuan, Yong-Mei Wang

Journal of Electrochemistry

Layered Li[Ni0.475Mn0.475Co0.05]O2 materials have been prepared by a solid-state pyrolysis method.Experiments of XRD,SEM,cyclic voltammetry and charge/discharge cycling were carried out.It can be learned that when calclined at 800 ℃,the sample showed the highest first discharge capacity of 178.8 mAh·g-1 at a current density of 20 mA/g in the voltage range 2.3~4.6 V

Go to article

Study On The Microstructure Of Pb-Sn Alloy Obtained From Quasi-Two-Dimensional Electrodeposition, Bin Sun Aug 2006

Study On The Microstructure Of Pb-Sn Alloy Obtained From Quasi-Two-Dimensional Electrodeposition, Bin Sun

Journal of Electrochemistry

A two-layered structure of eutectic-solid sulotion is formed in the microstructure of Pb-Sn alloy obtained from quasi-two-dimensional electrodeposition.It is showed that this unique structure is caused by the variation of the current density on the growth interface.When the interface is located in the front of the whole deposits,the current density is high.So the Pb and Sn can deposit together and the eutectic texture forms.When the interface is in the rear of the whole deposits,the current density is low.At this moment the electrodeposition of Pb is the dominant reaction,and the Pb-based solid solution appears.

Go to article

Investigation On The Resistance To Electrochemical Oxidation Of Carbon Nanotubes With Various Diameters, Yu-Yan Shao, Ge-Ping Yin, Yun-Zhi Gao, Peng-Fei Shi Aug 2006

Investigation On The Resistance To Electrochemical Oxidation Of Carbon Nanotubes With Various Diameters, Yu-Yan Shao, Ge-Ping Yin, Yun-Zhi Gao, Peng-Fei Shi

Journal of Electrochemistry

The resistance to electrochemical oxidation of multi-wall carbon nanotubes(CNT) with various diameters is investigated by applying a fixed potential of 1.2 V(RHE) for 120 h in 0.5 mol L-1 H2SO4.The oxidation current of CNTs decreases with their diameters,but CNTs between 10~20 nm in diameter(D1020) shows the lowest oxidation current.XPS analysis shows that,after oxidation,the increase in surface oxygen for D1020 is the smallest,implying that the oxidation degree for D1020 is the lowest.The conclusion can be reached that CNTs between 10~20 nm in diameter are the most resistant to electrochemical oxidation.The difference in electrochemical stability of CNTs …

Go to article

Influence Of Crystallinity On The Kinetics Of Li Ion Insertation And Deinsertation In Spinel Limn2O4, Rong-Hua Zeng, Dong-Sheng Lv, Wei-Shan Li Aug 2006

Influence Of Crystallinity On The Kinetics Of Li Ion Insertation And Deinsertation In Spinel Limn2O4, Rong-Hua Zeng, Dong-Sheng Lv, Wei-Shan Li

Journal of Electrochemistry

Two spinel lithium manganese oxides of different crystallinity were prepared by sol-gel process and were studied by using inducfively coupled plasma,X-ray diffraction,scaning electron micrographs,constant charging and discharging,cyclic voltammetry and electrochemical impedance spectrometry,the results show that the sample treated under 700 ℃ has higher crystallinity than the sample treated under 500 ℃,however,the sample with lower crystallinity has higher discharge capacity and better cyclic performance that due to quicker charge exchange speed and quicker diffusion speed of Li-ion.

Go to article

Voltammetric Behavior And Its Determination Of Acetaminophen At Poly (Congo Red) Modified Electrode, Hong-Bin Luo, Ya-Feng Zhang, Wei Chen, Xin-Hua Lin, Xiao-Yan Lin Aug 2006

Voltammetric Behavior And Its Determination Of Acetaminophen At Poly (Congo Red) Modified Electrode, Hong-Bin Luo, Ya-Feng Zhang, Wei Chen, Xin-Hua Lin, Xiao-Yan Lin

Journal of Electrochemistry

Cyclic voltammetry was used to prepare poly(Congo Red) film on glassy carbon electrode and to study the electrochemical behavior of acetaminophen on poly(congo red) modified electrode.Experimental resultal shows that the poly(congo red) modified electrode exhibits excellent electrocatalytic effect on the oxidation of acetaminophen.The peak currents of linear sweep voltammogram are linear to the acetaminophen concentrations over the range of 2.0×10-7～2.0×10-6 mol·L-1.The detection limit has been estimated to be 4.0×10-8 mol·L-1.This method can be used for the determination of acetaminophenin real sample.

Go to article

Preparation And Supercapacitor Properties Of Yttrium Doped Nio, Dan-Dan Han, Ye Chen, Mi-Lin Zhang, Chang Shu, Chun-Xia Zhang, Peng-Cheng Xu Aug 2006

Preparation And Supercapacitor Properties Of Yttrium Doped Nio, Dan-Dan Han, Ye Chen, Mi-Lin Zhang, Chang Shu, Chun-Xia Zhang, Peng-Cheng Xu

Journal of Electrochemistry

Yttrium doped Nano-NiO were synthesized by chemical precipitation method.Characterization and performance of the samples were studied by X-ray diffraction,the results showed that the doping Yttrium did not change the crystal structure of NiO,but the size of crystalline grain was reduced.The electrochemical properties of the electrode materials were measured in the three electrode system.Electrochemical properties of NiO were researched by cyclic voltammetry,constant current charge/discharge and AC impedance methods.It could be seen that the chemical doping improved the specific capacitance and the utilization of active materials.When the weight ratio of NiO with Y2O3was 1∶0.1,the composite material had the …

Go to article

Study On The Preparetion And Electrochemical Beavior Of Nitrogen Doped Tetrahedral Amorphous Carbon Electrode, Ke Liu, Guang-Fu Wang, Zheng-Hao Wang Aug 2006

Study On The Preparetion And Electrochemical Beavior Of Nitrogen Doped Tetrahedral Amorphous Carbon Electrode, Ke Liu, Guang-Fu Wang, Zheng-Hao Wang

Journal of Electrochemistry

taC∶N films are a good materials for semiconductor electrodes.But further studies are hampered by the ohmic contact problem,which occurs between the silicon and the lead.By studying the influence of heat treatment on the film's property,it is believed that ohmic contact should be made on the silicon first,and then the film be deposited.A set of taC∶N electrodes with various nitrogen content have been prepared.CV study indicates that the cathodic limits move slowly to positive direction.while the anodic limits are unchanged with the increasing of nitrogen content.As a result,the electrochemical windows get narrow either.

Go to article

48th Rocky Mountain Conference On Analytical Chemistry Jul 2006

48th Rocky Mountain Conference On Analytical Chemistry

Rocky Mountain Conference on Magnetic Resonance

Final program, abstracts, and information about the 48th annual meeting of the Rocky Mountain Conference on Analytical Chemistry, co-endorsed by the Colorado Section of the American Chemical Society and the Rocky Mountain Section of the Society for Applied Spectroscopy. Held in Breckenridge, Colorado, July 23-27, 2006.

Go to article

Electrochemical Studies Of Iron-Doped Nickel Oxide Electrode For Oxygen Evolution Reaction, Jin-Zhao Huang, Zheng Xu, Hai-Ling Li, Guo-Hu Kang, Wen-Jing Wang May 2006

Electrochemical Studies Of Iron-Doped Nickel Oxide Electrode For Oxygen Evolution Reaction, Jin-Zhao Huang, Zheng Xu, Hai-Ling Li, Guo-Hu Kang, Wen-Jing Wang

Journal of Electrochemistry

In this paper,the iron-doped nickel oxide thin film as anode catalyst was prepared by RF reactivesputtering method.The oxygen evolution reaction(OER) on the iron-doped nickel oxide was investigated withcyclic voltammetry,liner sweep voltammetry,polarization curves and electrochemical impedance spectroscopy.Results showthat the iron acts as active site in the film which makes the overpotential lower,and changes therate-limiting from primary discharge of OH-ions to the recombination of oxygen atom.With the increasing of ox-ygen content in flu ratio during sputtering,the electrocatalytic activities of the film increase.Iron-doped nickeloxide thin film is promising material as OER electrocatalyst for hydrogen production than the nickel electrode.The oxygen overpotential on the …

Go to article

Electrochemical Impedance Spectrum Of Ferrocene At A Rotating Disk Glassy Carbon Electrode And Its Interaction With Dna, Can-Hui Chen, Hong Li, Jian-Zhang Zhou, Zhong-Hua Lin, Wei Zhu, Quan-Xin Zhang May 2006

Electrochemical Impedance Spectrum Of Ferrocene At A Rotating Disk Glassy Carbon Electrode And Its Interaction With Dna, Can-Hui Chen, Hong Li, Jian-Zhang Zhou, Zhong-Hua Lin, Wei Zhu, Quan-Xin Zhang

Journal of Electrochemistry

The electrochemical impedance spectrum(EIS) of ferrocene(Fc) at a rotating glassy carbon(GC) electrode and its interaction with calf thymus DNA in Tris-NaCl buffer solution(pH=7.2) have been investigated by using electrochemical techniques such as rotating disk electrode(RDE),EIS and its data fitting.A plateau of the limiting current for the voltammetric curve and two capacitance arches obtained at the rotating GC electrode are exhibited.The interaction of Fc with DNA is represented by the decrease of limiting diffusion current and the increase of electrochemical reaction resistances with the increase of DNA concentration,respectively.On the other hand,based on the theoretical analysis and data fitting of RDE and …

Go to article

High Density Lifepo4/C Synthesized By Controlled Crystallization And Microwave Carbon Thermal Reduction, Chang-Ping Tang, Jie-Rong Ying, Min Lei, Wei Li, Chang-Yin Jiang, Chun-Rong Wan May 2006

High Density Lifepo4/C Synthesized By Controlled Crystallization And Microwave Carbon Thermal Reduction, Chang-Ping Tang, Jie-Rong Ying, Min Lei, Wei Li, Chang-Yin Jiang, Chun-Rong Wan

Journal of Electrochemistry

The spherical FePO4·xH2O was prepared in the solution by controlled crystallization.The precursor FePO4 was obtained in high temperatureceramic approach,then the high density LiFePO4 /C was synthesized by microwave carbon thermal reduction.The structure and morphology of the materials were characterized by means of XRD and SEM techniques,and the electrochemical properties were studies by charge-discharge experiments.

Go to article

Effect Of Cracks On Corrosion Of Rebar In Concrete Studied By Wire Beam Electrode, Guo-Xi Li, Xian-Lu Hou, Ri-Long Zhu, Jin-Feng Hu, Yan-Na Du May 2006

Effect Of Cracks On Corrosion Of Rebar In Concrete Studied By Wire Beam Electrode, Guo-Xi Li, Xian-Lu Hou, Ri-Long Zhu, Jin-Feng Hu, Yan-Na Du

Journal of Electrochemistry

The effects of crack and ethanolamine on corrosion of rebar in concrete were studied by measuring the distribution of corrosion potential and polarization resistance of iron wires in 10% NaCl solution.The results showed that the diffusion of water,oxygen and chloric ion toward concrete was accelerated by the crack which intensified the nonuniform corrosion of iron wire with the regions near to crack as anode and the uncracked regions as cathode.Ethanolamine could diffuse into the body of concrete and absorb on the surface of iron wire,which reduced iron corrosion evidently and successfully inhibited the nonuniform corrosion caused by crack without changing …

Go to article

Study On Composite Organic Inhibitor Of Zinc Electrode In Alkaline Solutions, Xue-Tao Bu, Guang-Chuan Liang, Cui Li May 2006

Study On Composite Organic Inhibitor Of Zinc Electrode In Alkaline Solutions, Xue-Tao Bu, Guang-Chuan Liang, Cui Li

Journal of Electrochemistry

The synergetic influence of sodium dodecyl benzene sulfonate(SDBS) with Tween-20(Tween) on zinc electrode was studied by polarization experiment,surface tension test,discharge test and SEM.It is found that the composite inhibitor ST has a much higher efficiency.The addition of Tween reduced the critical micell concentration of SDBS on zinc electrode remarkably and the distribution of adsorption became more homogeneous.ST inhibits corrosion of zinc electrode and improves discharge capacity of the whole battery.Through electrochemical morphological observation of anodic passivation behaviors of zinc electrode,the absorption of ST on electrode surface makes discharged production much smaller and keeps crude porous structure intact.Passivation of zinc electrode …

Go to article

Electrochemical Behavior And Reduction Mechanism Of High Valence Silver Oxide Ag3O4 In Alkaline Solution, Yan Cheng, Ming Yu, Man-Ming Yan, Zhi-Yu Jiang May 2006

Electrochemical Behavior And Reduction Mechanism Of High Valence Silver Oxide Ag3O4 In Alkaline Solution, Yan Cheng, Ming Yu, Man-Ming Yan, Zhi-Yu Jiang

Journal of Electrochemistry

The electrochemical properties of high-valence silver oxide Ag3O4 in alkaline solution were investigated for the first time and the reduction mechanism of Ag3O4 was proposed. It can be recognized that Ag3O4 consists of Ag(Ⅲ) and Ag(Ⅱ)~(*). From the results of voltammetry and XRD experiments it was found that the reduction process of Ag3O4 was more complicated. It could be electrochemically reduced through the series reactions of Ag(Ⅲ) →Ag(Ⅱ) →Ag(Ⅰ) →Ag(O) at low discharge rate or Ag(Ⅲ) →Ag(Ⅰ) →Ag(O) at higher discharge rate.And the Ag(Ⅱ)~(*) could be reduced to …

Go to article

Application Of Electrolessplating Technology In Interconnection Manufacturing Of Ultralarge-Scale Integration, Zeng-Lin Wang, Zhi-Juan Liu, Hong-Yan Jiang, Xiu-Wen Wang, Shingubara Shoso May 2006

Application Of Electrolessplating Technology In Interconnection Manufacturing Of Ultralarge-Scale Integration, Zeng-Lin Wang, Zhi-Juan Liu, Hong-Yan Jiang, Xiu-Wen Wang, Shingubara Shoso

Journal of Electrochemistry

In this paper,research progresses in electroless plating for damascene copper process were reviewed.Electroless nickel ternary alloy deposition for barrier layer and electroless copper plating for seed layer were presented.Bottom-up copper fill high-aspect-via-hole and electroless plating after ICB-Pd catalytic layer for seed layer were mainly introduced.The applications of electroless plating in ultralarge-scale integration were discussed,and the developing tendency was also suggested.

Go to article

Synthesis Of Zinc Polyhedral Microspheres And Applications In Alkaline Zn-Mno2 Battery, Hua Ma, Chun-Sheng Li, Fang-Yi Cheng, Chun-Yuan Zhou, Feng Gao, Jun Chen May 2006

Synthesis Of Zinc Polyhedral Microspheres And Applications In Alkaline Zn-Mno2 Battery, Hua Ma, Chun-Sheng Li, Fang-Yi Cheng, Chun-Yuan Zhou, Feng Gao, Jun Chen

Journal of Electrochemistry

The zinc polyhedral microspheres were synthesized by evaporation of pure zinc powders via a vapor-transport process.The results characterized by XRD and SEM show that the as-synthesized zinc powders are polyhedral microspheres with the diameter of 2~3 μm.The electrochemical investigation showed that the capacity of the as-assembled AA-size primary alkaline Zn-MnO2 battery was increased to 3.14 Ah under the constant discharge current of 100 mA by using the as-deposited microspherical zinc powders as the anode active materials and γ-MnO2 nanowires as the cathode active materials,indicating their potential application in high-energy batteries.

Go to article

Electrodeposition Of Three-Dimensional Porous Copper Films Using Hydrogen Bubbles As Template, Ya-Feng Sun, Zhen-Jiang Niu, Shu-Qiong Cen, Ze-Lin Li May 2006

Electrodeposition Of Three-Dimensional Porous Copper Films Using Hydrogen Bubbles As Template, Ya-Feng Sun, Zhen-Jiang Niu, Shu-Qiong Cen, Ze-Lin Li

Journal of Electrochemistry

Using cathodic hydrogen bubbles as a template,the three-dimensional(3-D) porous copper films have been successfully electrodeposited from a bath of 0.2 mol·dm-3 CuSO4 and 1.5 mol·dm-3 H2SO4,effects of deposition parameters including temperature,current density and additives(Na2SO4,HCl and Polyethylene glycol(PEG)) on the morphologies of the deposits have been systematically studied.SEM results showed that both the pore size and thickness of the pore walls decreased with cooling the electrolyte temperature or adding(Na2SO4) or PEG into the bath when the other deposition parameters were fixed.With addition small amounts of HCl …

Go to article

Structure And Properties Of Electrodeposited Sn-Co Alloy Electrodes As Anode Material For Lithium-Ion Secondary Batteries, Hong-Hong Jiang, Ling Huang, Shun-Wei Zhou, Fu-Sheng Ke, Fang-Zu Yang, Xiao-Yong Fan, Shi-Gang Sun May 2006

Structure And Properties Of Electrodeposited Sn-Co Alloy Electrodes As Anode Material For Lithium-Ion Secondary Batteries, Hong-Hong Jiang, Ling Huang, Shun-Wei Zhou, Fu-Sheng Ke, Fang-Zu Yang, Xiao-Yong Fan, Shi-Gang Sun

Journal of Electrochemistry

The Sn-Co alloy deposits were prepared by electroplating.The structure and electrochemical performance of the electroplated Sn-Co alloys have been investigated in detail. Experimental results show that the porous Sn-Co alloy film exhibits hexagonal solid solution,with Sn as the solvent, Co as the solute. The texture of the Sn-Co alloy coating exhibits(110) preferred orientation. Electrochemical tests show that the porous Sn-Co alloy coating electrodes can deliver a discharge capacity of 643mAh/g in the first cycle. At the 20h cycle the charge was 461mAh/g. At initial charge curve the irreversible capacity is probably associated to a combination of processes, which may …

Go to article

Corrosion Behavior Of The Welding Seam Of The Q235 Steel Jointed By J420 Electrode In Ammonium Sulfite Solution, A-Li Lei, Qiao-Qin Guo, La-Jun Feng May 2006

Corrosion Behavior Of The Welding Seam Of The Q235 Steel Jointed By J420 Electrode In Ammonium Sulfite Solution, A-Li Lei, Qiao-Qin Guo, La-Jun Feng

Journal of Electrochemistry

The corrosion behavior of welding seam of the Q235 steel jointed by J420 electrode in ammonium sulfite solution was researched.The results of electrochemical method of welding seam and metallurgical structure analysis showed that the poor corrosion resisting property was determined by its structure after the Q235 steel was jointed by J420 electrode.The sulfite corrosion rate was accelerated by increasing the temperature and concentration of ammorium.

Go to article

Preparation Of Spherical Ni(Oh)2 Coated With Coooh And Its Fast Charge Performance, Min-Jie Yang, Jun-Min Nan, Jian-Jun Xue, Yan Cui, Ming Cui May 2006

Preparation Of Spherical Ni(Oh)2 Coated With Coooh And Its Fast Charge Performance, Min-Jie Yang, Jun-Min Nan, Jian-Jun Xue, Yan Cui, Ming Cui

Journal of Electrochemistry

Spherical Ni(OH)2 was coated with CoOOH through chemical precipitation and electrolytic oxidation.The influences of CoOOH coating on fast charge performance ofMH/Ni battery were studied by preparing high capacity and fast charge AA size MH/Ni batteries.The sample coated with CoOOH was characterized by Infrared spectrum(IR) and scanning electron microscopy(SEM).The results showed that the internal resistance decreased 3.4 mΩ,the charge plateau lower and the cell temperrature was below 55 ℃ at the end of charging process when the cathode active material used Ni(OH)2 coated with CoOOH as compared with that doped by CoO.In addition,an initial discharge efficiency of 90.6% and …

Go to article

Effect Of Preparation Conditions On Electroluminescence Of Porous Silicon, Ya-Jun Yang, Qing-Shan Li, Xian-Yun Liu, Ning Zhang, Bo Zhao, Xue-Gang Zheng, Ming-Ji Shi, Da Chen, Jing-Jing Wang May 2006

Effect Of Preparation Conditions On Electroluminescence Of Porous Silicon, Ya-Jun Yang, Qing-Shan Li, Xian-Yun Liu, Ning Zhang, Bo Zhao, Xue-Gang Zheng, Ming-Ji Shi, Da Chen, Jing-Jing Wang

Journal of Electrochemistry

Electrically induced visible light emitting porous silicon devices with the structure of ITO/PS/p-Si/Al were fabricated by evaporation-anodic oxidation method.The light emission last for a few hours under 7.5V forward bias conditions.It was shown that the electroluminescence(EL) peaks shifted to the blue with the increasing of current density,erosion time and solution concentration.In order to achieve samples with low driven voltage,long light emission time and high EL efficiency,porous silicon should be prepared under low current density and short erosion time.

Go to article

Tyrosinase Immobilizarion On Boron-Doped Diamond Electrodes And The Determination Of Phenolic Compounds, Yan-Li Zhou, Jin-Fang Zhi May 2006

Tyrosinase Immobilizarion On Boron-Doped Diamond Electrodes And The Determination Of Phenolic Compounds, Yan-Li Zhou, Jin-Fang Zhi

Journal of Electrochemistry

As-grown BDD surfaces were first functionalized by photochemically linking vinyl groups of allylamine,producing covalently linked amine-terminated active BDD surfaces.Then the tyrosinase was immobilized onto the BDD surface through peptide linking.Cyclic voltammograms of phenol,pcresol and hydroquinone were measured using the tyrosinase-modified BDD electrode and amperometric characteristics such as sensitivity,linear response range and stability were studied.

Go to article

Electrochemical Studies On Electrocatalytic Activity Of AuCore PtShell Nanoparticles To Methanol Oxidation, Fang Bao, Jian-Lin Yao, Ren-Ao Gu May 2006

Electrochemical Studies On Electrocatalytic Activity Of AuCore PtShell Nanoparticles To Methanol Oxidation, Fang Bao, Jian-Lin Yao, Ren-Ao Gu

Journal of Electrochemistry

AucorePtshell nanoparticles with different thicknesses were prepared by using chemical reduction method,and characterized by ultraviolet-visible spectroscopy(UV-Vis),transmission electron microscopy(TEM) and cyclic voltammetry(CV).The electrocatalytic activity of AucorePtshell nanoparticles with the mean diameter of 70~80 nm to methanol oxidation was investigated by cyclic voltammetry in the acid solution.The results revealed that the prepared core-shell nanoparticles were covered by Pt shell and exhibited the similar optical property and electrocatalytic activity with the normal Pt surface.Moreover,the electrocatalytic activity increased with the electrochemical sweep in the certain potential range.It might be contributed by the special loose structure of Pt shell …

Go to article

Electrochemical Preparation Of Gd-Ni Alloy Film In Acetamide-Urea-Nabr Melt, Bi-Qing Chen, Jian-Chao Wang, Chen-Yu Guo, Jin-Gui Wang, Qing Liu May 2006

Electrochemical Preparation Of Gd-Ni Alloy Film In Acetamide-Urea-Nabr Melt, Bi-Qing Chen, Jian-Chao Wang, Chen-Yu Guo, Jin-Gui Wang, Qing Liu

Journal of Electrochemistry

Cyclic voltammetry was used to study the electroreduction of Ni2+ to Ni on Pt and Cu electrode in acetamide-urea-NaBr melt at 353K.It is irreversible in one step.At Pt and Cu eletrode the diffusion coefficient and electron transfer coefficient of Ni2+ in 0.063mol/dm3) NiCl2-acetamide-urea-NaBr melt were determined.The transfer coefficient α=0.28 and diffusion coefficient D_(0)=4.63×10-5 cm2·s-1 of the Pt eletrode and transfer coefficient α=0.22 and diffusion coefficient D_(0)=6.05×10-7 cm2·s-1 of the Cu eletrode were measured.It was put emphasis on that Gd3+ is not reduced to Gd alone …

Go to article

Cerium-Based Spontaneous Coating Process For Corrosion Protection Of Aluminum Alloys, James O. Stoffer, Thomas J. O'Keefe, Matthew O'Keefe, Eric L. Morris, Scott A. Hayes, Paul Yu, Alex Williams, Berny F. Rivera Vasquez, Xuan Lin May 2006

Cerium-Based Spontaneous Coating Process For Corrosion Protection Of Aluminum Alloys, James O. Stoffer, Thomas J. O'Keefe, Matthew O'Keefe, Eric L. Morris, Scott A. Hayes, Paul Yu, Alex Williams, Berny F. Rivera Vasquez, Xuan Lin

Chemistry Faculty Research & Creative Works

A cerium-based coating for corrosion resistance is applied by exposing a cleaned aluminum-based component to a corrosion-inhibiting cerium solution containing cerium ions in the presence of an oxidizing agent. The coating deposits spontaneously without an external source of electrons.

Go to article

2nd Annual Undergraduate Research Conference Abstract Book, University Of Missouri--Rolla Apr 2006

2nd Annual Undergraduate Research Conference Abstract Book, University Of Missouri--Rolla

Undergraduate Research Conference at Missouri S&T

No abstract provided.

Go to article

Structural And Magnetic Properties Of La Mn₁₋ₓfeₓo₃ (0 < X < 1.0), X.-D. Zhou, L. R. Pederson, Qingsheng Cai, Jinbo Yang, B. J. Scarfino, M. Kim, William B. Yelon, William Joseph James, Harlan U. Anderson, C. Wang Apr 2006

Structural And Magnetic Properties Of La Mn₁₋ₓfeₓo₃ (0 < X < 1.0), X.-D. Zhou, L. R. Pederson, Qingsheng Cai, Jinbo Yang, B. J. Scarfino, M. Kim, William B. Yelon, William Joseph James, Harlan U. Anderson, C. Wang

Materials Science and Engineering Faculty Research & Creative Works

Electronic, structural, and magnetic properties of Mn-doped lanthanum ferrites were studied by neutron diffraction, superconducting quantum interference device, and impedance spectroscopy. Neutron diffraction refinements were performed with the constraint of full La occupancy, which showed the presence of excess oxygen when x < 0.4. Mixed valent Mn cations and cation vacancies, therefore, exist in all the samples. The samples with x > 0.7 are magnetically ordered at room temperature with orthorhombic symmetry (Pbnm). When x < 0.3 the structure is rhombohedral and magnetically disordered above 16 K. The majority carriers, electron holes, correspond to high oxidation states of Mn. The carrier concentration is determined from the Seebeck coefficients, and is a function of temperature and Fe concentration. The measurements of conductivity and Seebeck coefficients show polaron hopping at elevated temperatures.

Go to article

First Prev Next Last