Chemistry Commons^™

Electroless Nickel Plating On Carbon Nanotube With Non-Palladium Activation Procedure, Guang-Hui Hu, Hui-Huang Wu, Fang-Zu Yang

Journal of Electrochemistry

A new procedure of surface activation without using palladium salt was proposed for electroless nickel plating on carbon nanotubes.In the procedure,carbon nanotubes were oxidized by nitric acid and then neutralized with NaOH to create carboxyl surface groups which were used to adsorb Ni²⁺ ions,thereafter the adsorbed Ni²⁺ ions were chemically reduced into Ni nano-particles as a catalytic center for electroless nickel deposition,all these were further confirmed by infrared absorption spectra and electron microscopic observations.The results indicate that the procedure is feasible to electroless nickel plating on carbon nanotubes.The different morphology of deposits obtained from electroless plating was also …

Conductivity Of Comb Polyether Pure Solid Polymer Electrolyte, Lin Ye, Peng Gao, Zeng-Guo Feng, Feng Wu, Shi Chen, Guo-Qing Wang

Journal of Electrochemistry

A comb polymer was synthesized through cationic ring-opening polymerization starting from a monomer 3-hydroxymethyl-3-methyl-oxetane.The ion conductivity was measured by CHI660A electrochemical station under various lithium salt concentrations and various temperatures.The highest ion conductivity was recorded to be 10^-4.43 S/cm at room temperature and 10^-3.44 S/cm at 80 ℃.DSC results showed that the segment moves more difficultly with the increasing of lithium salts concentration.XPS found the existence of aggregating lithium ions in POE5 and POE10,and it suggested that POE20 had a suitable lithium concentration for polymer electrolyte.

Studies On Pva-Cmc-Koh-H2O Alkaline Polymer Electrolytes, An-Bao Yuan, Jun Zhao

Journal of Electrochemistry

A given amount of sodium carboxymethyl cellulose(CMC)was added to PVA complex and thus the PVA-CMC-KOH-H₂O alkaline polymer electrolyte with this modification was prepared.The properties of the polymer electrolyte films were characterized by AC impedance,cyclic voltammetry,differential thermal analysis and infrared spectroscopic analysis methods.The polymer electrolyte exhibited a high ionic conductivity,typically 10^-2S·cm^-1 with an electrochemical stability window of about 1.6 V on stainless steel blocking electrodes.The influence of the film composition such as KOH,H₂O and CMC on ion conductivity was investigated.In addition,a preliminary study was carried out on the polymer electrolyte for Ni/MH battery.It was …

Anodic Behaviors Of Pb-Ca-Sn-Re Alloy And Tradditional Pb-Ca-Sn Alloy In Sulfuric Acid Solutions, Dang-Guo Li, Gen-Shu Zhou, Liang Yao, Guan-Fa Lin, Mao-Sheng Zheng

Journal of Electrochemistry

The anodic behaviors of Pb-Ca-Sn-Re and Pb-Ca-Sn alloys were investigated at 1.28 V(vsHg/(H₂SO₄)) in 4.5 mol/L sulfuric acid solution by means of ac voltammetry,ac impedance and cyclic voltammetry.The results showed that the corrosion-resistance property of Pb-Ca-Sn-Re alloy is better than that of tradditional Pb-Ca-Sn alloy,the growth of Pb(Ⅱ) compounds was inhibited in the film of Pb-Ca-Sn-Re alloy,and the film impedance of Pb-Ca-Sn-Re alloy was decreased,indicating that the conductivity of the film was(increased),which is helpful to enhance the deep recycling property for lead acid battery.

Mechanism Of Self Discharge Performance Improvement In The Ni-Mh Batteries With Naoh Electrolyte, Xiao-Feng Li, Tong-Chi Xia, Hui-Chao Dong, Yan-Wei Wei

Journal of Electrochemistry

The self-discharge performance and charge efficiency at 60 ℃ for Ni-MH battery can be markedly enhanced by using NaOH electrolyte instead of KOH electrolyte.Both the results of electrochemical impedance spectroscopy and cyclic voltammetry tests indicate that the separation of H₂ from the negative electrode may be partly blocked in the former because of the change of the adsorption/desorption behavior of H on the surface of the negative electrode,thus results in an improvement of self-discharge performance of the battery.

2006 National Conference On Corrosion Electrochemistry And Measuring Methods, Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

Degradation Of Aniline Wastewater By Electro-Heterogeneous Catalysis Reactor, Wei-Li Liu, Ai-Li Zhang, Ji-Ti Zhou, Bao-Jun Jia, Qun-Li Zhu

Journal of Electrochemistry

The treatment of aniline wastewater was investigated using novel electro-heterogeneous catalysis reactor.The effects of applied cell voltage,electrolysis lime,pH value and the electrolyte on electrolysis were investigated.The experimental results show that the reactor with a cell voltage of 30 V,an electrolysis time of 1 h,pH value of 7 and a salinity of 800 mg/L can achieve the best removal efficiency on aniline,which is more efficient than the sole electrochemical reactor.

Preparation Of Spinel Limn2O4 Cathode Materials For Li-Ion Batteries Based On Sol-Gel Process, Xiang-Ming He, Li Wang, Guo-Yun Zhang, Chang-Yin Jiang, Chun-Rong Wan

Journal of Electrochemistry

Spinel LiMn₂O₄ was prepared from CH₃COOLi·2H₂O,Mn(CH₃COO)₂ and adipic acid based on sol-gel process.XRD analysis showed that when the sintering temperature increased,the crystallinity increased,and the capacity also increased.However,its cycleability reached a maximum value at 750 ℃.The sintering duration also influenced on the capacity.The optimized performance was obtained when the sintering was carried out at 750 ℃ for 20 h.Under these conditions,as-prepared spinel LiMn₂O₄  presented the initial discharge capacity of 130 mAh·g^-1 and 125 mAh·g^-1 at 15^th cycle.

Special Photoelectrochemical Response Of Nano-Crystalline Tio2 Electrode, Bi-Bo Lan, Jian-Zhang Zhou, Yan-Yan Xi, Hong-Xiang Chen, Guang-Hua Yao, Zhong-Hua Lin

Journal of Electrochemistry

The nano-crystalline TiO₂ electrodes were prepared by spread method,electrodeposition and sol-gel method.The experimental results show that the nano-crystalline TiO₂ electrodes have special photoelectrochemical response-the photocrrent-potential curves appear peaks.The special photoelectrochemical behaviors of nano-(crystalline) TiO₂  electrodes are ascribed to nano-structure as well as special light induced redox reaction mechanism of nano-crystalline semiconductor electrodes.

Electrocatalytic Oxidation Of Glucose On Nano Pt/C Electrode, Cui-Lian Chen, Xiao-Lan Wei, Pei Kang Shen

Journal of Electrochemistry

Nano Pt/C electrocatalysts were prepared by intermittent microwave heating method.The electrooxidation of glucose on smooth Pt and～Pt/C electrodes has been studied and compared.The results showed that the electrochemical properties on nano Pt/C were improved due to the reduction of the overpotential and the increase in the kinetic rate.The surface area would be significantly increased when the particle size of the catalyst was reduced to nano-scale,resulting in the increase in the activity.The enhancement in the resistance to poisoning could be explained that the oxygen-containing species are easier to react with poisoning species on nano Pt/C and re-active the electrode.

Effects Of Sulfide Ions On The Inhibiting Efficiency Of Eda As A Copper Corrosion Inhibitor In Dilute Hcl Solution, Wen-Juan Qu, Rong-Gui Du, Chang-Jian Lin

Journal of Electrochemistry

The anticorrosion action of EDA on copper in dilute HCl solution and the effect of sulfide ions on the inhibiting efficiency were studied by the Tafel plot method.The corrosion potential of Cu shifted to more positive value and the corrosion current density decreased after the addition of Na₂S to the solution.The results indicated that sulphide ions could increase the inhibiting efficiency of EDA because of the synergistic inhibition effect between EDA and Na₂S,resulting from the adsorption of HS^- on the surface of Cu,facilitated the adsorption of EDA to form a highly protective adsorbed layer which …

The Complex Of Pasp And Tungstate As Inhibitors Of Cupronickel B10′S Corrosion In 3% Nacl Solution, Qun-Jie Xu, Guo-Ding Zhou, Hui-Feng Wang, Wen-Bin Cai

Journal of Electrochemistry

AC impedance and polarization curve measurements were conducted to study the effects of environ-ment-friendly inhibitors PASP,Na₂WO₄ and their complexes on the corrosion of cupronickel B10 in 3%NaCl solution.The results indicate that PASP or Na₂WO₄ alone does inhibit the corrosion of B10,and most effectiveconcentrations are 40 mg/L and 60 mg/L for PASP and Na₂WO₄,respectively.With the total concentration of 40mg/L for the complex inhibitors,the optimum complex ratio of PASP to Na₂WO₄ was 3:1.The complex of such a combination showed a significantly synergetic inhibition effect on the corrosion of B10.

The Effect Of Solution Concentration On Properties Of Ru-Ti-Ir Oxide Anode Coatings, Ke Wang, Yan Han, Jun-Tao Wang, Xiao-Ling Zhang, Yu-Pu Sun

Journal of Electrochemistry

The anode coatings of Ru-Ti-Ir oxide with various solution concentrations were prepared by thermal decomposition.The scanning electron microscope(SEM),energy dispersive X-ray detector(EDX),X-ray diffraction(XRD),accelerated life,polarization curve,cyclic voltammetry and electrochemical impedance.spectroscopy(EIS)tests were carried out.The results showed that there was an obvious effect of solution concentrations on the morphology of the coatings,but little effect on polarization of chlorine evolution.Voltammetric charges and double layer capacitances of anode coatings had a tendency to fall down firstly then increase afterwards as the solution concentration increased.

Electrochemical Reduction Behavior Of Benzaldehyde In The Ionic Liquids, Ning Zhao, Wen-Ju Dong, Qi-Zeng Shi

Journal of Electrochemistry

In this paper, the electrochemical reduction of benzaldehyde was investigated in C₄MIMBF₄, C₆MIMBF₄  and C₈MIMBF₄ ionic liquids by cyclic linear sweep voltammetry,cyclic square-wave voltammetry and chronocoulometry.Benzaldehyde exhibits two successive one-electron irreversible reduction(E_P1=-1.39 V, E_P2=1.69 V) with GC electrode in C₄MIMBF₄, the voltammetric data for benzaldehyde give diffusion coefficients of 1.5*10^-8cm²/s and 1.3*10⁸cm²/s. There is one current peak in C₆MIMBF₄  and C₈MIMBF₄ ionic liquids due to their stronger alkalinity …

Oxygen Enrichment Effect Of Ceo2 To The Cathode Performance Of Proton Exchange Membrane Fuel Cell, Xiang-Li Hou, Hong-Feng Xu, Jian-Hua Dong, Xin Sun

Journal of Electrochemistry

CeO₂ was added to Pt/C catalyst in the cathode of PEMFC by both sol and impregnation methods.The samples were evaluated by TEM,cyclic voltammogram techniques and proton exchange membrane fuel cell performance test.The addition of CeO₂ obviously improved the performance of PEMFC and represented a notable function of oxygen enrichment in the cathode side.But with the addition of CeO₂,part of the catalyst surface was covered and led to the performance drop of the PEMFC.The best content of CeO₂ is 1% when it is added by impregnation method and 3% when it is added by sol method.

Effects Of Srb Biofilm And Corrosion Product Films On Corrosion Behavior Of Carbon Steel, Jing Lin, Yong-Gui Yan, Guang-Zhang Chen, Guang-Zhou Liu, Qing-Fen Li

Journal of Electrochemistry

Electrochemical techniques and surface analysis techniques were applied to study corrosion characteristic of A₃ steel.The effects on corrosion behavior of A₃ steel by sulfate-reducing bacteria(SRB)(biotic media)and corrosion product(abiotic media)were studied.The results showed that biofilms and corrosion product films play different role during different stages.Biofilms were easier flaky with increasing of its thickness.Non-uniform biofilms reduced pitting corrosion of the specimens.The corrosion product films formed under abiotic conditions were more adherently to the surface of the metal than those formed in biogenic media.

In-Situ Detection Of The Effect Of Brighter In The Solution For Nickel And Phosphor Alloy, Jian Zheng, Ning Li, De-Yu Li, Guo-Feng Cui

Journal of Electrochemistry

In this work,the gold-plated mica was used for the substrate,the concentration of 5% of normal plating solution for the nickel was used as the mother solution,and the effect for the deposition by the brighter with ECSTM was in-situ detected.The solution for deposition without the brighter has no brightness,though the values of the roughness and the H_(A-V) have reduced in evidence after deposition;the solution for deposition with the complete brighter although has great brightness,the values of the roughness and the H_(A-V) have increased(after) deposition;the solution for deposition with the half brighter has a moderate effect on the H_(A-V) and (brightness).Hence,the brighter …

Nanodot-Based Organic Memory Devices, Zhengchun Liu

Doctoral Dissertations

In this study, resistor-type, diode-type, and transistor-type organic memory devices were investigated, aiming at the low-cost plastic integrated circuit applications. A series of solution-processing techniques including spin-coating, inkjet printing, and self-assembly were employed to fabricate these devices.

The organic resistive memory device is based on a novel molecular complex film composed of tetracyanoquinodimethane (TCNQ) and a soluble methanofullerene derivative [6,6]-phenyl C61-butyric acid methyl ester (PCBM). It has an Al/molecules/Al sandwich structure. The molecular layer was formed by spin-coating technique instead of expensive vacuum deposition method. The current-voltage characteristics show that the device switches from the initial 'low' conduction state to …

Electrochemical Deposition And Characterization Of Fe₃O₄ Films Produced By The Reduction Of Fe(Iii)-Triethanolamine, Hiten M. Kothari, Elizabeth A. Kulp, Steven J. Limmer, Philippe Poizot, Eric W. Bohannan, Jay A. Switzer

Chemistry Faculty Research & Creative Works

In this paper, we demonstrate that films of magnetite, Fe₃O₄, can be deposited by the electrochemical reduction of a Fe(III)-triethanolamine complex in aqueous alkaline solution. the films were deposited with a columnar microstructure and a [100] preferred orientation on stainless steel substrates. In-plane electrical transport and magnetoresistance measurements were performed on the films after they were stripped off onto glass substrates. the resistance of the films was dependent on the oxygen partial pressure. We attribute the increase in resistance in O₂ and the decrease in resistance in Ar to the oxidation and reduction of grain …

Segmental Dynamics Of Poly(Isopropyl Acrylate)-D7 On Silica, Piyawan Krisanangkura, Frank D. Blum

Chemistry Faculty Research & Creative Works

For a polymer film deposited on a surface, the strength of the surfacesegment interaction affects the mobility of polymer-chain segments. The selfconsistent field lattice model of Scheutjens and Fleer,1 based on mean-field lattice models of polymer at interfaces,2 has been used to describe the distribution of conformations of polymers on surfaces. Adsorbed-polymer segments may be classified as belonging to loops, trains or tails. There are different techniques used to study the molecular motion of the polymer including modulated differential scanning calorimetry (MDSC)3 and nuclear magnetic resonance (NMR).4,5 in this work, solid-state deuterium (2H) NMR was used to characterize the polymer …

Segmental Dynamics In Poly(Methyl Acrylate) On Silica: Molecular-Mass Effects, Burak Metin, Frank D. Blum

Chemistry Faculty Research & Creative Works

The effect of molecular mass on the segmental dynamics of poly(methyl acrylate) (PMA) adsorbed on silica was studied using deuterium quadrupole-echo nuclear magnetic resonance (NMR) and modulated differential scanning calorimetry. Samples adsorbed on silica (all about 1.5 mg PMA/m2 silica) were shown to have more restricted segmental mobility, and higher Tg's, than the corresponding bulk PMA samples. Around the glass-transition region, adsorbed samples exhibited segmental mobility, which could be classified as heterogeneous due to a superposition of more-mobile and less-mobile components present in the deuterium NMR spectra. This heterogeneity was consistent with a motional gradient with more-mobile segments near the …

Molecular Mass And Dynamics Of Poly(Methyl Acrylate) In The Glass Transition Region, Burak Metin, Frank D. Blum

Chemistry Faculty Research & Creative Works

The segmental dynamics of bulk poly(methyl acrylate) (PMA) were studied as a function of molecular mass in the glass-transition region using 2H NMR and modulated differential scanning calorimetry (MDSC). Quadrupole-echo 2H NMR spectra were obtained for four samples of methyl-deuterated PMA-d3 with different molecular masses. The resulting spectra were fit using superpositions of simulated spectra generated from the MXQET simulation program, based on a model incorporating nearest-neighbor jumps from positions on the vertices of a truncated icosahedron (soccer-ball shape). The lower molecular-mass samples, influenced by the presence of more chain ends, showed more heterogeneity (broader distribution) and lower glass transitions …

Segmental Mobility Of Chain Ends In Poly(Methyl Acrylate)-D3, Burak Metin, Frank D. Blum

Chemistry Faculty Research & Creative Works

Better control of polymeric materials can be achieved with a thorough understanding of the dynamics of their constituents. In the present study, we consider polymer chains as composed of chain middles and chain ends. Even though chain ends do not comprise much of the sample by mass, they may play a crucial role in the ultimate properties of the polymers. Although chain ends have been assigned a higher mobility, as compared to chain middles, there have not been a large number of experimental studies that directly probe their mobility. Among those, the studies of Kitahara et al.1 and Miwa et …

Synthesis And Thermal Behavior Of Poly(Methyl Acrylate) Attached To Silica By Surface-Initiated Atrp, Manikantan B. Nair, Frank D. Blum

Chemistry Faculty Research & Creative Works

The modification of the surface of an object dictates the response of the object to an external environment.1 Surface-modified materials and nanoparticles have attracted immense interest due to the various desirable electronic, optical and magnetic properties they possess.2 Silica is widely used as an inorganic filler. Surface modification of the silica, with a variety of organic moieties, facilitates the utilization of silica in conjunction with organic systems. The resulting organic/inorganic hybrid materials have significant potential applications. This work reports the synthesis and characterization of modified silica, and poly(methyl acrylate) attached to the modified silica. An observation of the thermal behavior …

Crystal And Electronic Structures Of Linh₂, Jinbo Yang, X.-D. Zhou, Qingsheng Cai, William Joseph James, William B. Yelon

Materials Science and Engineering Faculty Research & Creative Works

The crystal structure of LiNH₂ was reinvestigated using powder neutron diffraction with high sensitivity. The compound crystallizes in the tetragonal space group I4 with lattice parameters α = b= 5.034 42 (24) Å, c = 10.255 58 (52) Å. It is found that H atoms occupy 8g1(0.2429, 0.1285, 0.1910) and 8g2 (0.3840, 0.3512, 0.1278) sites. The bond lengths between the nearest nitrogen and hydrogen atoms are 0.986 and 0.942 Å, respectively. The bond angle between H-N-H is about 99.97°. These results are significantly different from those of previous experiments. The electronic structure was calculated according to the revised structural …

Interaction Between Metal Fission Products And Triso Coating Materials: A Study Of Chemical Bonding And Interdiffusion: 1st Quarterly Report, 2006, Clemens Heske

Fuels Campaign (TRP)

This project is devoted to an in-depth study of the chemical and electronic impact of metal fission products on the coating layers in TRISO nuclear fuel. In particular, there is a focus on the investigation of Pd, Cs, and Ag and their interface formation with SiC and carbon-based substrates. A variety of surface and near-surface bulk sensitive probes that investigate the occupied and unoccupied electronic states of the substrate and the metal overlayer have been utilized. By a controlled and stepwise deposition of the metal overlayer, it is possible to gain substantial insight into the formation of interfaces and their …

Interaction Between Metal Fission Products And Triso Coating Materials, Clemens Heske

Fuels Campaign (TRP)

In this project the chemical bonding and interface formation of metal fission products with the coating materials used in TRISO fuel particles is investigated. The interface formation of Pd, Cs, and Ag with SiC and pyrolytic carbon is studied in detail. Using the SiC single crystals and TRISO coating materials as substrates, interfaces are prepared under controlled conditions in an ultra-high vacuum environment and are studied with a photoelectron spectroscopy, Auger electron spectroscopy, Inverse Photoemission, X-ray emission spectroscopy, and X-ray absorption spectroscopy. Recent additions to the experimental approach include microscopic techniques (Transmission Electron Microscopy, Scanning Tunneling Microscopy, Atomic Force Microscopy) …

Dissolution, Reactor, And Environmental Behavior Of Zro2-Mgo Inert Fuel Matrix, Kenneth Czerwinski

Fuels Campaign (TRP)

This project examines inert fuels containing ZrO₂ and MgO as the inert matrix, with the relative amount of MgO varied from 30% to 70% in ZrO₂. Reactor physics calculations are used to examine suitable quantities of burnable poisons from the candidate elements Gd, Er, or Hf with reactor grade Pu providing the fissile component, with up to 10% of ²³⁹Pu. Ceramics are synthesized and characterized based on the reactor physics results. The solubility of the fuel ceramics, in reactor conditions, reprocessing conditions, and repository conditions, are investigated in a manner to provide thermodynamic data necessary for …

Growth Of Ge Quantum Dots On Si(100)-(2×1) By Pulsed Laser Deposition, M. S. Hegazy, H. E. Elsayed-Ali

Electrical & Computer Engineering Faculty Publications

Self-assembled germanium quantum dots (QDs) were grown on Si(100)-(2×1) by pulsed laser deposition. In situ reflection-high energy electron diffraction (RHEED) and postdeposition atomic force microscopy are used to study the growth of the QDs. Several films of different thicknesses were grown at a substrate temperature of 400 °C using a Q-switched Nd:yttrium aluminum garnet laser (λ= 1064 nm, 40 ns pulse width, 23 J/cm ² fluence, and 10 Hz repetition rate). At low film thicknesses, hut clusters that are faceted by different planes, depending on their height, are observed after the completion of the wetting layer. With increasing film thickness, …

The High Temperature Corrosion Of 2205 Duplex Stainless Steel With Nacl Deposit, Fu-Fu Peng, Chaur-Jeng Wang, Yu-Chang Lin

Journal of Electrochemistry

The objective of this study was to figure out the hot corrosion behavior of 2205 duplex stainless steel (2205 DSS) within the temperature ranges from 550 to 850℃ in the static air condition with 2 mg/cm² NaCl deposit, and in the air atmosphere condition with a constant flow rate of 500 vppm NaCl_(g), respectively. Experimental results show that the hot corrosion kinetics met the parabolic rate law and the corrosion rate increased constantly with increasing temperature. The scales formed included Fe₂O₃/Fe₃O₄/Cr₂O₃ and FeCr₂O_{4 …}